Do-it-yourself air grill repair

In detail: do-it-yourself air grill repair from a real master for the site my.housecope.com.

Behind the external simplicity of the design of the air grill lies a rather complex, multi-component device with a wide range of functions. Nevertheless, do-it-yourself air grill repair with a heater replacement is quite affordable even for users with a minimum of technical knowledge. Functionally, this is an improved version of the convection oven, designed for cooking with the help of heated air flows.

The main structural elements are:

heat and impact resistant glass container;
cover with built-in electric motor, heating element and a pair of fans;
control module on the cover bracket.

Despite the overall reliability and durability of the device, its main components are not immune from breakdowns. Their occurrence is often associated with banal wear and tear during prolonged and intensive use, neglect of the requirements of the instructions, voltage drops and other adverse factors.

There may be several such problems, but the failure of the heating element is most common and is relatively easy to fix on your own compared to other technical problems.

Not always the lack of heating is caused by a breakdown of the air grill itself or a malfunction of the heater. First of all, you need to check the device for inclusion. This is a common problem, likely causes include:

lack of voltage in the network;
socket failure;
loose contact of the power cable;
wrong mode selection;
tightly closed lid.

If the device turns on, adjusts, but does not reach operating temperature, the most likely cause is a malfunction of the heating element. Depending on the design features, it can be made in the form of a halogen lamp or various heating elements. The location is the bottom surface of the cover. The lamp or heating element is fixed on special holders and connected by contacts to the control board. Externally, the element is covered with a protective grille.

Video (click to play).

Repair will have to begin with disassembly of the structure. The process is straightforward and intuitive. To do this, you will need a Phillips screwdriver. After loosening the fixing screws:

remove the protective grill;
remove retaining brackets;
dismantle the heating element;
release contacts.

If a hologen was initially installed in the air grill, you can try replacing it with a heating element with a spiral. Its advantage is a larger working resource. The lamp is designed for a couple of years of trouble-free operation under standard conditions. The service life of a high-quality heating element without replacement is five times longer. Another advantage of this option is maintainability.If the problem is related to a broken spiral, it can be repaired. But this is acceptable in cases where there is no workable analogue. A restored coil will not last long, plus it will take a long time to repair.Therefore, in both cases, it is recommended to immediately replace the defective part and check the repaired air grill for heating.In addition to the heating element, the inoperability of the air grill may be associated with other breakdowns. Not all of them can be fixed on your own, but it will be useful to know about them. Frequently mentioned are a non-working fan and failure of the control unit.This is the most important element of the device, which ensures uniform baking, roasting of the product due to blowing with a directed hot stream. Turns on when the heating element reaches the set temperature. When it fails, the quality of cooking decreases.The problem may be related to a broken soldering, which is easily restored on its own without leaving home without visiting a service center. If the node is completely inoperative, it must be changed to a healthy one:

for this purpose, you will need to completely disassemble the cover;

conduct a visual inspection of the contacts;

if they are in order, replace the node with a working one with an exact match of those. parameters.

The most difficult malfunction to fix on your own, requires skills in working with electronics. The control module ensures the functioning of:

Externally, the control panel can be made in a push-button or more modern touch version, which is more prone to failure. With such a breakdown, the device does not turn on or refuses to accept the settings for the desired mode of operation.

Self-repair in this case is hardly possible, the most that can be done is to make sure that the element is malfunctioning, that is, check the condition of the contacts and the presence of voltage with a multimeter.

The board is located in the device case, fixed above the cover; to access it, you will have to completely dismantle the structure. After making sure that it is malfunctioning, it is best to return everything to its place and contact the service center.

The best way to avoid malfunctions and prolong the life of your Airfryer is to follow the manufacturer's instructions exactly. If, nevertheless, a breakdown has occurred, you should not rush and puzzle over the question of how to repair the air grill with your own hands. First of all, you should correctly assess the complexity of the problem and possibly take your device to a specialist. This will be more expensive, but it will avoid the loss of time and loss of the device associated with self-repair errors.

Aerogrill is designed for cooking by heat treatment. Heating of products is made by a stream of hot air. Structurally, the air grill can be divided into three components: a heater, a fan and a control unit. Troubleshooting and do-it-yourself air grill repair at home can also be divided into several stages according to the number of nodes:

the device does not turn on or the operating modes are set incorrectly;
the air does not heat up or does not warm enough;
No air flow, fan is loud.

If the device does not turn on, the indication on the control unit is off, then the search for the cause must begin with external inspection of the device. The problem may be a faulty power cord, electrical plug, or damage to the case.

If the integrity of the cord insulation is broken, it must be replaced. The power cable may not show any external damage, but may still be defective. You will need a multimeter to check. The cord is disconnected from the device and checked for contact between the ends of the cable with a multimeter in resistance measurement mode. The serviceability of the fuse is also checked, the blown one is changed.

Many models of air grills are equipped with limit switch on the lid, which does not allow the heating to be turned on when the work bowl is not closed. If you press the switch with your finger, you can hear a distinct click. The absence of sound indicates a broken contact. The limit switch can only be replaced after disassembling the cover body. The cover is at the same time the body containing all the working elements.

The glowing indicator indicates that the device is receiving power, and the previous step can be skipped. If the device still does not work, most likely it is out of order control circuit. Unfortunately, its repair requires specific knowledge; it is impossible to consult an unprepared person in absentia. However, the problem may be a break in the connecting wires between parts of the device. To inspect the wires, you will need to disassemble the case.

You need to start disassembling the unit by unscrewing the screws securing the mesh from the bottom of the case.

Photos of disassembly are given on the example of Hotter air grill.

A heating element and fan blades are visible under the grid.

The screws and nut highlighted in the photo allow you to disconnect the part of the device on which the heater is fixed. Below are the contacts of the heating element.

We check the heating elementif it doesn't get hot. We disconnect the terminals with wires from the heating element, now it is possible to check its serviceability. The check is carried out with a multimeter in the same way as the cable was checked. A faulty heater will show an open circuit, the heating element will have to be changed. Along with the disassembly, the connecting wires are inspected for damage, the cause of the problem may be this.

In more expensive models, heating is done by a quartz lamp. Its malfunction can be determined by the glow: there is no radiation or the lamp goes out periodically - the lamp needs to be replaced.

Typical malfunctions of the air grill blower system:

airflow is absent;
the fan hums when turned on;
a rumble or rattle is heard during operation;
the airflow is too weak.

To check the fan, you need to continue to disassemble the device. We unscrew the screws securing the lower part of the fan and the electric motor.

We inspect the motor.

One of the possible reasons why the motor and, accordingly, the fan spins slowly or does not rotate at all, may be the ingress of grease on its shaft. After hardening, the fat interferes with the normal operation of the engine. This can be seen in the picture. Therefore, a hum is heard: the engine cannot cope with the load and its winding starts to hum.

The accumulation of fat is removed with a rag, and the residue is washed off with gasoline, alcohol or other liquid that dissolves oil. Just removing the fat from the shaft is not enough. Need to produce shaft lubrication. This will require Ciatim engine oil.

In the absence of a specialized oil, you can use petroleum jelly, but when heated, it becomes liquid, flows off the shaft, and soon the operation will have to be repeated.

Rumble, rattle and other unpleasant sounds during operation can be caused by bearing failure on the motor shaft. The bearing is located on the back of the engine.

Most often, it is also thickened grease. By unscrewing the two fixing screws, they gain access to the bearing itself. As before, we apply a new lubricant inside it. We return the cover to its place and make several turns of the shaft with our hands to evenly distribute the oil.

All suggested operations make sense when the motor winding is not damaged.. Therefore, during disassembly, we carefully study the connecting wires for integrity. We call the conclusions of the motor winding with a multimeter. A winding break is usually not possible to eliminate; a replacement of the electric motor will be required.

The limit switch on the cover was previously mentioned. To get to it, you have to disassemble the entire body. But you can check its serviceability in another way. To do this, you need to determine which wires go to it from the printed circuit board. It's not difficult at all: two conductors go in his direction. We disconnect them from the circuit board and connect a multimeter to them. When you press the limit switch, the resistance on the tester display should change from infinity to zero. Otherwise, the limit switch is faulty and needs to be replaced.

The possible malfunctions of a fairly cheap Hotter model are discussed above. Similar manipulations can revive similar air grills from Supra. Expensive aerogrills have a more complex device, they are controlled electronic circuits, therefore, it is better to repair them in service centers, although you can try to fix some of the above malfunctions yourself.

If your household appliances are out of order, then you should not say goodbye to it. You don't even have to take it to a service center.Instead, check out the instructions and tips to help you repair your airfryer yourself.. Common malfunctions have long been painted, and the design is clear and not very complicated, so you can get down to business.

An air grill is a kind of air draft oven, a mixture of a heater and a fan. A special grill acts as a heating element, which in turn is blown by air currents. The primary heat source is an infrared lamp. All these important parts are separated from the glass bowl where the food is placed.

The design usually consists of several elements:

sealed glass bowl;
a quartz lamp covered with a grate and slightly lowered inside the bowl;
a fan consisting of lower and upper blades (the lower ones work to blow food, and the upper ones cool the motor);
partitions between the blades with holes for air removal;
bimetallic plate for temperature control;
control unit and display system.

The lid is usually equipped with a functional handle that completely turns off the power when opened. Cooking starts only when the appliance is hermetically sealed. Problems can be associated with the listed elements, so do-it-yourself air grill repair often begins with a diagnosis.

Any do-it-yourself repair of an electric grill or similar device requires familiarity with the internal workings. The electrical circuit consists of a switch on the cover and handle. From it, the signal through the timer goes to the motor that starts the fan. Relays and quartz lamps are connected in parallel.

You often encounter the following problems:

the device does not turn on and does not respond to control;
the device heats up slightly;
air fryer fan does not spin;
the main control unit is broken.

Typically, a chicken carcass weighing about 1.5 kg is cooked for about 1 hour. The degree of readiness can be observed through the transparent walls. If the time increases noticeably, then this indicates possible malfunctions. There are other problems - the air grill simply does not respond to button presses or other malfunctions occur. But your device can still be repaired.

The design of this device has already been discussed above. It is not difficult, which allows you to quickly repair the air grill with your own hands. Usually one of three main components breaks:

thermal fuse;
a heating element;
Control block.

The third option is the most serious problem, because in this case it is quite difficult and expensive to repair the device. In addition, only specialists should be involved in restoration, but even they cannot guarantee a 100% result.

Breakdowns of the thermal fuse and the heating element are easily eliminated, and you can do everything yourself with minimal knowledge and tools. For this, a multimeter is suitable, which “rings out” all the elements.

If the heating element fails, then you can simply buy a new heating element. An ordinary steel model is inexpensive and can last for a dozen years. However, the disadvantages include slow heating, high energy costs. You can spend a little more, but buy more efficient carbon or halogen heaters.

If the problem lies in the thermal fuse, then usually the air grill does not turn on at all. A short-term power surge in the network often leads to such a problem. Although before taking serious measures, it is also better to check the outlet and wiring.

Do-it-yourself disassembly of the air grill is carried out in several stages:

the lattice of the quartz lamp is unscrewed;
the lower blades of the fan are dismantled;
the partition between the blades is removed;
the upper “cage” is removed (the motor of the device opens behind it);
the quartz lamp is removed, fastened with brackets to the partition;
if you want to replace the quartz lamp, you need to dismantle the cable connectors.

Before starting work, you should carefully inspect the body of the air grill and find all the screws that are hidden in deep grooves or behind decorative plugs.

Remove steel blades from the back, where the grip nut is usually located. This will make it much more convenient and safer.

Do not forget that before you start repairing your air grill, conduct a complete diagnosis. There are several reasons that can be misleading:

the outlet is out of order;
the device is incorrectly configured or the wrong mode is selected;
the lid is not fully closed.

Sometimes it is cheaper to replace one or another part than to buy a new convection oven. You can repair it with your own hands quite quickly and efficiently.

The first malfunction that is encountered most often is that the air grill does not turn on. You should not panic, because sometimes the following banal situations can be the cause of a breakdown:

The electrical plug is not connected to the socket or the contact is bad. No matter how strange it may look, nevertheless, the lack of power is very often the so-called cause of the breakdown of the air grill. Pay attention not only to the contact with the outlet, but also to the connection of the cord to the equipment itself (on the back, as shown in the photo). Very often, it is the last connection point that causes problems. In addition, check the integrity of the cord that you may have interrupted. If necessary, replace or repair the damaged area yourself. We talked about how to replace the plug in the corresponding article!
The socket has failed. Check the connection point itself, if there is voltage in it. Perhaps the air grill does not turn on because the outlet does not work. All you need for repair is to check the voltage in the socket with an indicator screwdriver as shown in the photo.
The correct mode is not set. If the display lights up, but nothing happens when you press the "Start" button, most likely you have set the operating mode incorrectly. This will be indicated by a timer, which will display the numbers 00:00.
The handle is not all the way down. In many models, a button is installed under the handle, which protects the equipment from accidental activation. If the handle is not tight, you will not be able to start cooking.

If all of the above points do not fit your case, you will have to make a more complex repair of the air grill on your own - disassemble the case and check each element of the circuit in turn.

To "diagnose" parts, you need to use a special tester - a multimeter. Using this tool, check the resistance of a fuse that blows during power surges. If the air grill does not really work due to the failure of the thermal fuse, replace it with a new one with the same parameters (it costs a penny). Replacement instructions are provided in the video lesson:

To prevent this malfunction from bothering you again, we recommend installing an overvoltage protection device!

If the fuse is OK, ring all other elements of the circuit - heating element, control unit, and also visually inspect all wire connections. Perhaps somewhere there was a break in the contact, which will need to be soldered. You can see how this technique works in this video:

In the event that the air grill does not heat up or heats slightly from below, we can say with confidence that the heating element does not work. The cause of the malfunction may be the wear of the heating element at the end of its service life or an open circuit. In the latter case, you can try to repair the damaged area, but according to many reviews on the Internet, it is easier to buy a new part than spend hours on repairs.

By the way, it should immediately be noted that the heating element in the form of a halogen lamp often fails, the service life of which is already 2 years compared to 10 years of a metal heating element. If the lamp under the cover does not heat up, do not replace it with the same one. It would be much more correct to replace the heating element with a metal one yourself. In this case, you will need to dismantle the protective grille, remove the brackets, unscrew the heater and disconnect the wires. After replacement, the parts are assembled in the reverse order. As you can see, do-it-yourself air grill repair, which does not gain temperature, can be done by yourself without certain knowledge in electrics!

Also, you may encounter a situation where the air grill does not fry the bottom of the dish or does not heat up at all due to the fact that the fan is not spinning. In this case, the repair of equipment comes down to the fact that it is necessary to disassemble the case and visually inspect the contacts connected to the fan. If there is a broken wire somewhere, solder it. In the event that the fan does not work completely, it is better to replace it with a new one with the same parameters and dimensions.

In order for you to understand the importance of good fan operation, we will now briefly describe its principle of operation. When the heating element reaches a certain temperature, the fan starts spinning and blows hot air towards the food. If the fan does not work properly, a situation may arise when the air grill does not bake well or does not fully cook food from below.

Well, the last, most difficult malfunction is when the control unit does not work - the timer, thermostat, power button or mode switch. In this case, a reverse moment may even occur when the air grill does not turn off. Most often, this situation occurs with touch displays, although they are convenient, they are more prone to breakdowns and costly repairs.

The only thing you can do is check the integrity of the contacts and ring the touch panel with a tester. If it really does not work, the repair will be beyond the power of a novice electrician, so you will have to hand over the equipment to a service center. Do not be afraid, because the situation when the air grill does not work due to a malfunction of the control unit is very rare and occurs only if you bought a cheap Chinese model of the device.

Here we have listed all the most popular malfunctions of this type of household appliances. As you can see, do-it-yourself air grill repair is quite realistic, so if the device does not work, now you know what to do to repair it yourself!

Also read:

Aerogrill is a convenient multifunctional device that allows you to cook delicious dishes by heat treatment of products. If this device stops working when it is still new and is under warranty, it is recommended to take it to a specialized center. There, professionals will take care of the repair of the air grill. If the equipment has already served, and the warranty period has expired, then you can try to fix it yourself.

The air grill is a device main nodes which are:

a heating element;
fan;
Control block.

A more detailed structure of the device is considered in the following photo.

The numbers in the photo correspond to the following structural elements:

cover with fan and electric heater;
control Panel;
cover bracket;
cover lifting mechanism;
plastic case;
flask;
network socket;
electrical cord.

As a rule, on the cover of the device there are power off and on button. When you open the lid, the cooking process stops automatically. In the event that the device is not closed tightly, it will not start working.

Repair of the device at home start with diagnostics, that is, with the search for problems. Common malfunctions include the following:

the device does not turn on at all or it suddenly turns off;
operating modes are not set at all or are incorrectly set;
the light panel goes out periodically;
air heating is weak or absent;
The fan does not work (no airflow).

If the air grill does not turn on, and in addition there is no light indication on the light panel, then the first thing to do is to inspect the device for external damage. It is possible that the cause of the malfunction is damage to the case, power cable or plug.

In the event that the cable is damaged, it is enough just to change it with a new one or reconnect the wiring at the break point and insulate it. The cord may look intact on the outside, but be inoperable. To determine the integrity of the cable cores, you will need a multimeter (pictured below).

Important! For diagnostics, you need to disconnect the power cord from the air grill and, in the resistance measurement mode set on the multimeter, check the integrity of the wires: touch the probes to the opposite ends of each of them. If the wires in the cable are intact, then the device will show that their resistance is practically zero. When there is a break in the core, the multimeter will give out infinity.

Further, with a multimeter in the same way it is necessary check the fuse. If it does not work, then it should be replaced.

Air grills on the lid contain limit switch. It blocks the operation of the device if the lid is not tightly closed. When you press the switch, you should hear a characteristic click, which indicates its good condition. If there is no sound, then this may indicate poor contacts or their breakdown. The trailer is replaced by disassembling the cover shell.

To check the limit switch and not disassemble the entire cover, you need to determine which wires come to it from the control board: as a rule, only two wires connected. Next, you need to detach them from the electrical circuit and connect them to the multimeter. When you press the microswitch, the resistance value on the device should change from infinity to 0. If there are no changes on the multimeter, then the limit switch is not working and needs to be replaced.

If all the lights are lit on the device, then this indicates a good power supply. But in the case when the heating or blowing of the cooked products does not occur, it is recommended to contact a specialized center. With such a malfunction, most likely, a wire break has occurredconnecting the parts of the device.

The lack of heating or blowing can also be a consequence failure of the control unit. In this case, the following elements do not work:

timer;
thermostat;
mode switch button.

The problem with the control unit most often occurs with cheap, non-original, devices without certificates with touch displays. The problem is considered one of the most difficult breakdownsrequiring to eliminate special knowledge in the field of electrical engineering. In case of malfunctions of this kind, it is better to immediately disconnect the device from the mains by removing the plug from the outlet.

For self-repair, you need to check the integrity of the contacts and ring the board using a tester (multimeter). In the event that there are no signals, then repairs at home will be very difficult for non-professionals. It is better take it to a repair shop unit.

If the control unit functions normally and all internal electrical wiring is intact, and the device heats up very little or does not heat up at all, then the heating element does not work. In an air grill, heating can be carried out due to heating element or halogen lamp (or its carbon counterpart). The latter fails more often, as it has a shorter service life (about 24 months) compared to the heating element (about 10 years).

Halogen lamp or heater can be replaced by yourself for parts of the same power. To do this, you will need to disassemble the entire device.In this case, the first thing to do to replace the heating element is to unscrew the bolts that hold the grid from the bottom of the device body (a model from the Hotter brand is taken as an example).

Below the grid are heating elements and fan (the photo below shows its blades).

The following photo shows the contacts of the heating element.

Important! To check the health of the heating elements, it is necessary to disconnect all contacts. The performance is checked with a multimeter, just like the power cable: in the event of a breakdown, the tester will show an open circuit. Then the heater needs to be replaced.

Definitely recommended view all wires for breakage or poor contacts at their connections. This is due to the fact that the reason may be precisely in them.

There are several indications by which it can be determined that fan defective:

no airflow or very little airflow movement;
air fryer buzzes when turned on;
during operation, an uncharacteristic rumble or rattle comes from the device.

To identify the causes, it is necessary take the device apart. It is necessary to separate the lower part of the fan and the electric motor (they are fastened with screws).

Next, carefully inspect the engine: you need to view the winding and all connecting wires for the presence of burnt areas and for their external integrity.

If grease gets on the shaft and freezes, it can cause malfunctions of both the electric motor and, accordingly, the fan. In this case, the fan blades will spin very slowly or not move at all. Recommended clear the shaft engine from pollution. After that, lubricate it with special machine or weapon oil.

If the motor winding is externally intact, then you will need to use a multimeter to determine the presence of internal breaks in it. For this, the device needs ring output winding. In the event of an open circuit, you will need to buy a new electric motor. At the same time, the necessary spare parts for repairs can be purchased on the official websites of the manufacturer or in stores that sell household appliances.

Loud sounds during operation of the appliance may be caused by bearing failure on the motor shaft. It is located on the reverse side.

Very often the problem is thickened grease. At the same time, by unscrewing 2 screws, you can access the bearing and remove the old lubricant. After that, you need to check the integrity of the bearing. If it is in order, then it must be lubricated with oil.

Important! When the bearing has crumbled, is badly worn out, or there is a crack in the cage, then it needs to be replaced.

Next, you need to assemble the air grill in the reverse order, returning the lid to its place. In order to distribute the oil inside the bearing and to check the ease of rotation of the fan, it is recommended turn the blades by hand.

As an example, when troubleshooting, an inexpensive Hotter air grill model was considered. All the actions considered will help to repair such devices at about the same price, for example, from Supra. More expensive devices are made differently. As a rule, such air grills contain more complex electronic circuits and in case of problems, it is recommended to immediately contact specialized service centers.

We consider an air grill to be a hybrid of an iron, a quartz heater, and a wind blower. Working together, they will allow you to get mouth-watering delicacies that would be problematic to prepare with other methods. We believe that the inhabitants of America adopted the technology of smoking bison from the Indians, then frying methods were introduced into everyday life. Grill, reminiscent of a skewer hanging over a fire. In fairness, let's say that infrared radiation makes a small contribution to cooking, the chicken turns out to be browned, tanned. Do-it-yourself air grill repair is much easier than, say, an iron.The screws are not hidden by artfully made decorative elements, buttons, regulators. A repairable device looks more attractive on the Russian market than a beautiful, but disposable one.

Thanksgiving Day is celebrated in memory of those who survived the hungry winter of the coast of colonized America. The settlers were helped by the local Indian Tiskvontum, who was later poisoned, according to historians, by warlike brethren.

The aero grill grate simultaneously acts as an infrared emitter and a heating coil blown by a fan. The device has an infrared (halogen) lamp, which acts as a primary source of heat. The lid is removable (start with it when you need to repair the air grill), the ring element is located with a perimeter from below. Separated from the working compartment of a giant glass bowl by a steel grate with randomly shaped holes. If you take the repair of the Hotter air grill, you will also have to face the mechanism for lifting the hinged lid.

They said that the air grill device resembles an iron for one simple reason. The regulator is made according to the scheme based on a bimetallic plate. Of course, there are many designs, it is powerless to list everything, simple devices are arranged like this:

Self-repair of air grills requires knowledge of the internal structure. At the input of the electrical circuit there is a switch pressed down by the handle. The fan motor is powered by a timer. Parallel to the branch, a relay is connected (adjusted by the corresponding knob), a quartz filament lamp. For convenience, a couple of indicators:

Timer operation. The lamp is on while the cocked mechanism is ticking.
Quartz work. The lamp burns synchronously with the heating element.

Beginners are interested in why indicators are needed. They will come in handy when do-it-yourself air grill repair becomes inevitable!

The quartz indicator is on, there is no heating, prepare five hundred to replace the coils.
As long as the timer indicator is on, the program is running. Even if the spring mechanism stops. In the rest position, on the contrary, neither the indicator should light nor the quartz lamp heat up.

On the temperature controller, notice the self-cleaning mode. Today, a popular word, an air grill could not do without an option, of course.

In fact, nothing complicated. A bucket of detergent water (dishes) is poured inside the bowl so that the foam does not reach the fan. The timer starts for 40 minutes. After the specified time, the quartz lamp grille and fan blades will become much cleaner.

Why the air grill is designed this way is a big question. Judge for yourself:

Inside there is a quartz lamp, separated from the working compartment by a grate. Steel is specially equipped with thick ceilings so that half of the radiation leaves the grating. Where does the rest go? Heats the table, floor, cooks, ceiling!

This is not rational. It is known that the efficiency of a halogen lamp is 98%, if the light heats the room, it is not good for cooking. Airfryer bowl is made of glass, stops ultraviolet radiation, not infrared. For a cook, of course, it is useful. Infrared radiation is used for the treatment, prevention, removal of postsyndromes in diseases of the nasopharynx. You will feel the heat of the air fryer lamp by raising your hand. Not convective heating! When the lamp turns off, the hand stops feeling warm. The only big drawback of the airfryer.

The appliance does not work in automatic mode when cooking other dishes. Some will object: the slow cooker is not omnipotent. However, the main recipes are automated. You'll have to work hard on the side ones. In an air grill, we consider the advantage of getting a roast without oil to be the dominant advantage. The main dish will not automatically cook. The cook must monitor the actions of the air grill, at the right time turn the meat over on the grill. In the recipe book, the moment is missed, the chicken will not cook lying on one side. The top of the roast is baked with shock, the bottom receives little heat.

From what has been said, it is clear what can break:

The quartz lamp burns out.
The engine fails.
Relay breaks.
The timer fails.

The main types of faults The air fryer is cleaned regularly.

You should start with a lattice of a quartz lamp. Then the lower blades, the partition are removed. Having removed the upper "squirrel cage", we will get access to the wall of the engine compartment. Behind her is the filling of the device. The quartz lamp is attached to the partition with brackets. Cable connectors are removable, it is better to dismantle, do not touch the metal fasteners. Unless, of course, you need to replace the quartz lamp.The air fryer is not an iron, but the screws can be hidden under decorative elements. First of all, the pens. In many models, screws are hidden under the lattice of the quartz lamp. Steel blades are held on the central nut. Do not take on disassembly. On the back of the blades there is a nut for gripping, or disassembly is not done from this side. In the course of the master, some readers will ignore the words - in case of a successful experience, unsubscribe in the comments.

Video (click to play).

We hope that now the readers of the VashTekhnik portal can repair the Hotter air grill, repair Ves air grills, arranged in a similar way. Cook barbecue, chicken. It comes out great, it goes into the mouth even better: om-nom-nom.