Ariston at 84 do-it-yourself repair

Details: ariston at 84 do-it-yourself repair from a real master for the site my.housecope.com.

Message SKORPION » 03 Dec 2009 20:59

Message MAYBAX » 04 Dec 2009 08:28

Message elremont » 04 Dec 2009 09:37

Message MAYBAX » 04 Dec 2009 10:52

Message bun » 04 Dec 2009 11:01

Think for yourself: how many people ask similar questions - where do you think you can get so many photos (taking into account the huge variety of models and brands of cars and the equally huge variety of breakdowns in different nodes)?

Message MAYBAX » 04 Dec 2009 11:20

Message elremont » 04 Dec 2009 13:29

Message MAYBAX » 04 Dec 2009 14:19

Message SKORPION » 04 Dec 2009 18:10

Message wave2m » 04 Dec 2009 19:51

A gentleman is a person with whom you feel like a gentleman.
Repair of washing machines, dishwashers, sewing machines and boilers in Nizhny Novgorod

Washing machine Hotpoint Ariston Italian manufacturer-reliable and high quality. But some parts of the washing machine sometimes become unusable.

You can, of course, send it to a service center for repair, but in order to save money and with skillful hands and a smart head, you can repair an electromechanical household appliance yourself.

Do-it-yourself Ariston washing machine repair is easy to do. Follow our washing machine restoration instructions, and your assistant will serve you for many years.

In the electromechanical device Ariston, the main reason leading to incorrect operation of the machine is blockages.
In addition, the heating element becomes unusable due to the appearance of limescale on the heating element due to hard water.
The pump is also faulty due to its long operation.
Sometimes the filling valve fails due to damage to the rubber gasket.
In rare cases, it is necessary to change bearings and seals.
Electronics almost never break, but we still touch on the issue of replacing the control unit a little.

Video (click to play).

It is easy to remove the blockage with your own hands. You need to check the drain filter, which is located at the bottom right under the panel.

By cleaning the filter, you will eliminate the cause of the washing machine malfunction. Less often, there is a blockage of the drain pipe, because it is thick.

The pump may be clogged, but rarely, because there is an additional filter in front of it.

The drain hose only becomes clogged if you installed it incorrectly.

Check the drain, it may also be clogged. Disassemble the unit, pull out the pipe, loosen the clamps, rinse it. Pull out the pump by unscrewing the fasteners and disconnecting the sensors.

Signs of a pump failure:

Drain pump hums but water won't drain.
The machine may stop while the system is running.
Water flows out slowly.

Ariston washing machine pump repair should be done as follows:

If the filling valve is broken in Ariston, then water constantly flows into the washer, even when it is not working, it is disconnected from the network.

To check the fill valve, you need to unscrew the fasteners and remove the top cover. The valve is located where the drain hose connects to the housing of the electromechanical unit.

Check gaskets first. If they have not lost their performance, measure the resistance of the valve. Put the probes on the contacts of the filling valve and check the resistance if it is optimal (from 30 to 50 ohms).

If it is less or more than it should be, it means that the water intake valve is not working. To replace it, you need to unscrew the old valve from the body and screw in a new one. Be sure to connect the sensors.

If the heating element is faulty, then it must be replaced. Its breakdown is signaled by the fact that the water does not heat up or washing according to all programs takes place in cold water. Sometimes the machine gives an error and stops.

To replace the heating element, the rear wall must be removed. Under the tank there are two contacts with a fastener in the middle. This is the ten. Measure the resistance of the heating element with a multimeter.

If the resistance is within the normal range, then you do not need to change the heating element - it is serviceable. To remove the heating element, you need to unscrew the screw in the middle and pull it towards you with rocking movements.

The water may not heat up due to the fragile connection of the wires to the heating element, which arises from the strong vibration of the washer. Water heating may be absent even if the temperature sensor malfunctions.

Take a tester or multimeter and check the resistance of the sensor cold and hot. If the resistance is the same, then it is broken and needs to be replaced. The resistance must be different.

The high-quality and durable material from which the drum of household appliances is made also becomes unusable, because solid foreign objects get into it, which can damage the assembly, forming cracks on it.

The plastic rib inside the drum can be deformed. To replace the drum, you need to remove it.

To remove the drum yourself, you need the following set of tools:

a set of screwdrivers, especially a Phillips screwdriver and a slotted nozzle;
screwdriver;
pliers;
hammer;
hexagons of different sizes.

Using a Phillips screwdriver, the bolts are removed from the rear, front and top walls, and then the panels themselves are removed.

Remove the powder container. Remove the module with a slotted screwdriver. The control unit does not have to be completely unscrewed, the main thing is that it does not interfere with removing the drum.

Remove the cuff of the hatch, pull out the lower bar by unscrewing the screws. From the loading tank, you need to dismantle the electronics, shock absorbers and other parts.

Remove the drum from the device and disassemble it. Remove the screws holding the two sides of the drum. Pry off the seals with a screwdriver and remove them.

In the drum, the bearing can break and wear out. It needs to be replaced. You only need to buy a bearing of the appropriate brand in a specialized store or order it on the official website of the Ariston washing machine, or purchase it at an equipment repair shop.

Use a metal rod and a hammer to knock out the bearings. If they are faulty, replace them. If the drum is deformed, then change it to a new one.

Reassemble. If the malfunction is in the plastic rib, then there is no need to disassemble the tank. The washer door is removed. A metal rod is taken, the diameter of which is smaller than the holes in the plastic rib of the drum.

The rod is inserted into one of the holes on the rib, the latch opens with it, the plastic part is removed. A new plastic rib is put in its place. Move the plastic rib along the groove until the latch engages the hole and closes.

The LED indicators on the control panel receive a signal from a faulty unit. An error code is displayed on the display, indicating a breakdown of some element.

In the Ariston Margarita 2000 washing machine, in the event of a malfunction, the power button starts flashing and the handle of the command device constantly rotates. The nature of the flashing is different depending on the fault. The codes can be found in the owner's manual.

The control unit may fail due to mechanical damage, water ingress on it. Do-it-yourself repair of the control module can be done on your own only when a small part has failed or you need to replace the board completely.

In other cases, please contact the service. Professionals will help you repair, resolder complex electronic circuits.

You need to unscrew the screws on the board or remove the plates with a wrench, depending on its brand. Remove the control unit, replacing with a new one. Screw the fasteners carefully so as not to damage any part.

The price of the repair depends on its complexity. If the device does not drain the water, then the cost of restoration work ranges from 1200 to 3000 rubles.

Repair of the control module costs more than 3500 rubles. The rattle and knock of the machine can be fixed at a service center in Moscow for a price of 3,000 to 5,000 rubles.

Today we shared with you the knowledge of how to repair the Ariston washing machine with our own hands.

We hope that everything will work out for you and self-repair will cost you inexpensively, you will not have to pay for disassembly and assembly of washing equipment, for restoration work with the help of specialists.

Ariston washing machines from an Italian manufacturer can be called a "model of reliability and quality", but they sometimes require attention. Repair of Ariston washing machines in some cases can be done by hand, and a specialist needs to be involved only in the most difficult cases.

In this article, we will analyze the frequent malfunctions of Hotpoint Ariston automatic washing machines, study the “symptoms” of such breakdowns and decide how to properly repair it yourself.

The vast majority of breakdowns of Ariston washing machines are related to their operation. This is recognized by the masters of service centers for the repair of washing machines. Sometimes we are talking about frankly improper operation, the user regularly makes gross mistakes, which lead to a breakdown. But most often, the cause of the breakdown is the operating conditions, which the user either did not know about, or guessed, but did nothing. A vivid example is hard water, which can completely disable the “home helper”!

So, what breakdowns are most often found on Hotpoint Ariston washing machines? We decided to compile a kind of rating of the frequency of breakdowns. When compiling the rating, we rely on statistical data provided by the leading service centers for the repair of washing machines.

blockages. Blockages themselves can hardly be considered breakdowns; rather, they are the cause of various breakdowns. However, it is blockages that craftsmen have to deal with most often, and it is strong blockages that most often paralyze the operation of various Hotpoint Ariston washing machines.
A heating element. In second place in our ranking is ten. Despite the fact that the heating element itself is of high quality, low-quality hard water does its job. Over time, the scale layer destroys even the best part and it has to be changed.
Water pump. In third place is the drain pump or pump. This part fails quite rarely and in most cases the reason is wear and tear from long-term operation.
Fill valve. Even more rarely, the filling valve fails. More precisely, not even the valve itself, but a rubber gasket. Rubber becomes dull over time and begins to let water through, this causes a malfunction. The gasket itself costs a penny, but the services of a master in replacing this gasket cannot be called cheap.
Bearings and seals. In fifth place are the breakdowns of bearings and seals. On Hotpoint Ariston washing machines, this is a rarity, but if such a breakdown occurs, you cannot continue to operate the machine.

Important! The electrics and electronics of the Hotpoint Ariston washing machine are intentionally not included in the rating, since it breaks very rarely.

If you have problems with blockages on the Hotpoint Ariston washing machine, do not rush to call the master, everything can be repaired quickly, with your own hands. How do you know that you are dealing with a blockage? The main sign of a blockage in the drain system is the idle operation of the drain pump, that is, it buzzes, but the water does not leave the tank. Usually, this trouble appears after the end of washing, the machine cannot drain the waste water to start rinsing and freezes, or it drains the water too slowly.

Strong blockage can be in several places:

in the drain pipe, between the tank and the drain filter - this happens less often, since the pipe is rather thick;
in the drain filter - there the blockage forms most often;
in the pump - in Ariston washing machines, blockages in the pump are rare, since an additional filter is installed in front of the drain pump;
in the drain hose - blockages rarely occur, mainly in cases where the hose was not installed correctly.

How to quickly clear blockages? First of all, you need to check and clean the easily accessible places of the washing machine where a blockage could occur. First, unscrew the drain filter, which is located on the Ariston machines at the bottom right under the narrow panel. Before unscrewing the filter, put a cloth over it, as water will flow from it. Remove all debris from the filter, and then screw it back on.

Next, it is important to check the drain hose and sewer. In some situations, a banal blockage in the drain pipe can force the user to turn to machine repair specialists when it would be more correct to turn to plumbers. And if everything is in perfect order, then it will be necessary to disassemble the machine, clean the nozzles and the pump. To remove the pipe, you will need to loosen two clamps, and to remove the pump, you will need to disconnect it from the sensors and unscrew the two fasteners.

If any malfunction occurs, the Hotpoint Ariston “washer” gives an error with a certain code displayed on the screen. It is very important to correctly recognize the error codes of Ariston washing machines, because this is a direct clue indicating the cause of the breakdown.

A broken inlet valve “according to symptoms” is quite difficult to confuse with other breakdowns of the Hotpoint Ariston washing machine. When the inlet valve stops shutting off the water, water begins to flow into the washing machine tank by gravity, even if the “home assistant” is turned off from the network.

If you hear the characteristic murmur of water being filled in and drained from the tank when the machine is turned off, be sure this is a valve.

To check the filling valve, you need to remove the top cover of the Hotpoint Ariston machine by unscrewing the two fasteners. The valve is located at the junction of the inlet hose with the body of the machine. First of all, we check the gaskets, if they are intact, then you need to measure the resistance of the device, and for this you will have to use a multimeter. We install the probes on the contacts of the filling valve and check. The device should show approximately 30 to 50 ohms.

A defective filling valve should be replaced with a similar one; self-repair is not possible. The replacement itself is done very quickly, we unscrew the old valve from the body and screw in the new one, not forgetting to connect the sensors. It is worse if the pump fails, because this is a rather expensive part.

A faulty pump gives itself out during washing, when the machine should drain the water, but it does not, while the pump either does not make any sounds at all, or it buzzes, but the murmur of the drained water is not audible.

Note! Strictly speaking, these symptoms are superficial and may be indicative of other problems (eg electronics), but it should make you think to check the pump first.

In the Hotpoint Ariston washing machine, it is located at the bottom and you can get to it through the bottom. It is better to check and replace the drain pump by a specialist, but you can do everything yourself, the main thing is to thoroughly study the progress of work.

The heating element is an important part of the washing machine, responsible for the temperature of the water in the tank, and therefore for the quality of the wash. If the heating element is faulty, the wash either does not start at all, and the system gives an error, or the wash is performed in cold water. Both should prompt you to check and replace the heating element in the Hotpoint Ariston washing machine.

Checking the heating element of the Ariston washing machine is not difficult at all. It is necessary to deploy the machine, in the lower part of the rear wall there is a service hatch, which is attached to the clamps and several self-tapping screws. We unscrew the screws, and squeeze the latches with a screwdriver, after which the cover will be removed. Behind the lid, under the tank, you will see two large contacts with a fastener in the middle - this is the heating element. We unscrew the screw, and then we begin to pull the heating element towards ourselves, pulling it out with shaking movements.

Note! Before pulling out the heating element, it’s a good idea to measure the resistance with a multimeter, perhaps the device is working, and you don’t need to touch it.

As we have already noted, failures of bearings and seals are the most rare malfunctions of Ariston washing machines. However, if this happens, urgent action must be taken. Recognizing such a breakdown is not difficult. When the bearing is destroyed, the moving elements begin to make unpleasant sounds, the shaft begins to rub against the bushing, which leads to wear. And if you do not take any measures and continue to wash, then this can lead to the fact that the drum will begin to play and damage the tank.

So that your favorite washing machine does not end up in a landfill, you need to contact a specialist when such sounds appear, or try to change the bearings yourself. If you are determined to do the work yourself, study the information offered on our website. Otherwise, with such a complex repair, it is not surprising to make serious mistakes. The main difficulty is that in order to get to the bearings, you need to disassemble the entire washing machine, along with the tank.

In addition, it will be necessary to correctly remove the old bearings without damaging the sleeve, and then correctly install the new ones so that re-repair is not required. Without proper skill, self-repair is not possible for many, so before taking on work, consider delegating it to a specialist.

In conclusion, we note that it is theoretically possible to repair malfunctions of Ariston machines with your own hands, especially if you have the time and patience. But still, in order to avoid mistakes and unnecessary expenses, it is better to contact a specialist because "the miser pays twice"!

Breakdowns among Ariston washing machines are an infrequent phenomenon, because manufacturers have long established their equipment as the most reliable. But still, even such excellent equipment can fail after a long time of operation. Malfunctions of the Ariston washing machine in most cases are typical and come down to replacing failed elements.TENA failure. Thanks to this detail, water is heated for greater efficiency of the washing process. If a failure occurs for this reason, the machine itself will determine this and issue the appropriate breakdown code (F03). This can be both a malfunction of the element itself, and its accompanying breaks in the power circuit due to the fact that the terminals have burnt out. To eliminate the breakdown, you need to replace the burned-out heating element or fix the terminals.Bearing failures. This malfunction is typical for almost all models of machines from any manufacturer, including the Ariston hotpoint model. You can see how this is done in the video or in this article:

Pump or filter malfunctions. Regardless of vertical or horizontal loading, model range, and other indicators, it may happen that the machine refuses to drain or fill with water. The reasons may be blockages, burnt pump winding.

Sometimes, in order to establish work, it is enough to clean the filters, if their further work is impossible, replace them. If everything is normal with the filters, but the water still does not drain, you need to replace the pump.

Most often, you need to tighten the fixing nut or change the rubber seal. Less often, the cuffs of the hatch, pipes can be the culprits. In this case, the problematic part should be replaced.

Noise during operation of the machine with correct bearings. In such situations, you need to check whether the machine is level. If not, you need to level its placement, and to reduce the level of vibration, you can put a rubber mat. If this is done and the car is still noisy, the problem may be the shock absorbers or the tank belt.

To make repairs, you need to check these parts and, in case of breakdowns, replace the necessary one. Another cause of noise may be small objects that have fallen behind the drum during washing. To eliminate noise, it is enough to remove this small thing. Also read this article: https://my.housecope.com/wp-content/uploads/ext/1504/prichiny-gromkogo-shuma-v-stiralnoj-mashine.html

Malfunctions of washing machines of other companies:

Ariston washing machines are equipped with a display that displays information about the washing process, mode. But there is another irreplaceable function of such a display. It will also display the breakdowns that have occurred under the fault codes. Each such code is responsible for some kind of breakdown, and knowing their meanings will help you quickly identify and eliminate the malfunction that has occurred.

The following codes may appear on the displays of Ariston hotpoint or aqualtis washing machines:

Knowing the trouble codes for Ariston hotpoint washing machines, you can find the reason for stopping work. Ariston washing machines have a complex device, but in many cases it is possible to make repairs with your own hands, while saving time and money.

Before calling technicians, read How to Clean the Detergent Dispenser, Troubleshooting – Ariston AT 84 User Manual

Installation and use instructions

If the washing results are not satisfactory or if

faults, read this section before calling a technician.

In most cases, you can solve the problems yourself.

Press lightly on the big

button on the front

distributor and pull out

n Is the plug inserted in the

load could work auto-

How to clean the detergent dispenser

Then rinse the distributor under running water (Fig. 3),

using an old toothbrush. Take out a couple of siphons, insert-

attached to the top of compartments 1 and 2 (Fig. 4), check for

are they clogged and flush them.

Install a pair of siphons in

until it clicks (Fig. 4, 2 and 1).

n Is the height too low?

n On the upper floors of buildings

leaks.
Don't leave work

hole.
Always leave the door

smell.
External panels of the machine

caution.
Machine body and rubber

Before proceeding with the repair of the Ariston washing machine, the novice master should know what to check first. I’ll tell you right away about the control module, this detail should be looked at only when you have checked all the main components for their performance. Below I will list, point by point, the diagnostics of which parts you should do. Many people, seeing that the lights on their typewriter are flashing, immediately sin on the control module, and in fact often the blinking of the indication does not indicate a breakdown of the module, but a malfunction of one or another part. The fact is that a modern washing machine has a self-diagnosis function that displays an error code on the control panel, that is, it shows which part it is desirable to pay attention to. You can look at the error codes for Ariston washing machines on this page, just don't be afraid of what is written there - about Indesit. Ariston and Indesit errors are identical. Well, now let's start diagnosing and repairing, below I will try to answer in detail the frequently asked questions that sound on my YouTube channel

Help me repair the Ariston WISL 105 washing machine. Everything works fine, but at the very beginning of the wash, when it starts to slowly spin the drum, the engine cannot turn it, it jerks and buzzes, then it jerks and buzzes in the other direction, and so on. After a few minutes, the speed turns on quickly and starts to twist, but it also spins with difficulty. I called the master through the dispatcher. He rang everything, the engine and control board, everything is normal, replaced the brushes. Turned on the washing machine, without laundry and it worked fine. The next day they threw underwear and everything repeated. I call him and tell him the reason, and he said that we should change the motor.I think so, if the engine grunted, it would not work at all, but only at the beginning of the wash and at low speeds, as if the engine power was not up to par. By hand, the drum spins easily and for a long time. What is the reason, can someone tell me.

What does change motor mean? Firstly, who should change it, why did you call the masters? Secondly, the motor may not have anything to do with it. Something points me to the failure of your master. Let's see what he should have checked first.

To summarize, I think that first of all, you need to change not the motor on the washing machine, but the master you invited to repair your washing machine. Of course, in your case, the engine can be so weird, but I will say that such behavior is more typical when there is not enough voltage. In general, do what I wrote above, and then we will look at the circumstances

Video how to check the motor from the washing machine

Thanks for the informative answer, we said goodbye to the master, called another. He first measured the voltage, as you basically wrote. We took an extension cord, connected a washing machine to it and a master tester, measured the voltage. It turned out to be 180 volts, that was the end of the whole repair, though they paid for the call. Yesterday my husband bought a current converter, one that draws 220 volts from the network and tried to wash it. Everything works great, thanks a lot for your helpIn general, of course, it’s cool that your masters have settled down, like do it yourself, and I’ll come and take the money. On this topic, I can also add the following, but it happens that the engine is covered, that is, some winding is a little hooked, and the control unit cannot be discounted either, but first of all, you still need to check the voltage in the network, like this do it right i wrote aboveThe ariston washing machine washed normally until the last moment, but today they threw the laundry in and decided to wash it, closed the hatch, pressed the start button, but nothing happens. The wash indicator and the lock signal are on, there are no buzzes, it does not collect water in the tank. I unscrewed the water supply hose from the washing machine to check the pressure, it pours no worse than from a tapThere can be many reasons for this malfunction, the fact is that almost all the details, even the pump, are responsible for taking water into the tank. Perhaps you are now surprised, but I will now try to explain to you why this is happening. In modern Ariston washing machines, there is an electronic control unit that, before starting washing, diagnoses all the components that are on your washer and if some part is not in working order, the module will not give a command to fill in water. Further, I will list in order the details that need to be checked, and you can find out how to check them on this page. I draw your attention to the fact that the link will take you to the Indesit washing machine repair page, it is practically the same unit, only the tags are different, and as for components and repairs, everything is the same. And so let's list what you should checkI have listed almost all the main breakdowns in which there may be no water inlet into the washing machine. There is only one thing left - this is the control module. If you have diagnosed all the spare parts and they are in working order, then call the wizard. I highly do not recommend repairing the control module myself, this spare part is very complicated and can only be repaired by a person who has certain experience and knowledge, not even every telemaster is able to do this repair with high qualityToday, our washing machine refused to drain the water. The first thing we did was clean the filter of the washing machine, pulled out a few coins and another tuft of wool. We decided to start and wash a little, the result was deplorable, having reached the rinse, the pump refused to drain the water, but you can hear how it buzzes. We again drained the water manually and decided to clean the filter, but this time, there was nothing in the filter.The husband took two wires and connected them to the drain pump, in short, he applied 220v there, the pump started working, the fan inside the filter was spinning. We again decided to wash and again reaching the rinse, the water remained in the washing machineAs I understand it, you checked everything except one, I just need to add to your story. You did everything right, yes, you can really apply 220 volts to the pump and see how it works, it’s very good that you cleaned the filter, but you also had to blow out the drain hose and wash the pipe that goes from the tank to the pump body. Very often I pull out various interesting things from this pipe. Sometimes socks get there, often staples from the bra, sometimes I pull out the heels. I think how to remove it, this pipe does not need to be told. Now a few words, I want to say about the drain hose that is inserted into the sewer. Before blowing it, be sure to unscrew the plug from the pump housing, that is, the filter. The fact is that there is a plastic ball in the pipe that goes from the tank to the pump body, and if the filter is not unscrewed, this ball can be blown into the tank, and we cannot allow thisEverything was done as you wrote. The filter plug was unscrewed, then the hose was blown out, 10 kopecks fell out, thinking they prevented the water from draining. They also washed the pipe for which you spoke, there was nothing significant in it, but there was a lot of dirt. Washed several times already, the washing machine drains the water. Thank youIn addition to this topic, I want to talk a little about other reasons why the Ariston washing machine does not drain water. First, the failure of the drain pump. The fact is that this breakdown can look different, the pump winding itself burns very rarely, but the impeller often jams. In practice, there are times when you come to a call, check the pump, everything seems to be fine, but when washing, it starts to fail, this is due to the fact that a large output appears on the mechanism of rotation of the impeller, it also happens that a coin or some other gets under the impeller nonsense that you can’t even see, so you need to check well with your finger or something else if there are any foreign objects under the impeller. Sometimes a thread is wound on the impeller, this also affects the operation of the drain pump. In general, it is necessary to check everything related to the patency of the hoses and the performance of the pump. If all this does not help, then you need to look at the module, but before that, be sure to check the wires that go from the module to the pump, they are often broken. From experience I can say that the control module, with such a breakdown, fails extremely rarely, so the brain is the very last detail that you need to climb intoWe have a Hotpoint Ariston-Akvaltis washing machine. Recently, the bearings made noise, at first there was a small rumble, and then the noise began to increase, there is also play on the drum. In the workshop, we were given too much money for repairs, we simply don’t have that kind of money. On your YouTube channel, I watched a video in which you change the bearings in an Indesit washing machine and I had a lot of questions. What is the difference between the tank of the Ariston Hotpoint - Aqualtis washing machine and the tank on your video. In particular, I am interested in: is it necessary or not to cut the tank, which company of bearings for a washing machine is better to use, which grease for the stuffing box should be bought. If you cut the tank, then what kind of glue is needed to glue the two halves and what is the best way to fix it - with self-tapping screws or boltsActually, the petition was two pages long, I just chose the most necessary from everything that the visitor of my channel wrote, he really had too many questions. Below you can watch a video that tells about all the nuances of replacing bearings in a washing machine, and now I will answer the questions that I was asked in orderThe site has a detailed article about lubrication and stuffing box, everything is described in detail there and be sure to watch the video belowTo glue the tank, I use a sealant - Dragon, for cars.For fasteners, I mainly use self-tapping screws, on my channel they made comments to me that self-tapping screws can be unscrewed, more than one hundred guys have already done this. I use bolts only where the self-tapping screws have scrolled. It happens that the tank is re-repaired for repair, in which case bolts can be used. In the video below, I talk about all the nuances of such a repair, it shows what glue I use, what lubricant, and so on.