Ariston at 84 DIY repair

Details: ariston at 84 DIY repair from a real master for the site my.housecope.com.

Message SKORPION 03 Dec 2009 20:59

Message MAYBAX 04 Dec 2009 08:28

Message elremont 04 Dec 2009 09:37

Message MAYBAX 04 Dec 2009 10:52

Message bun 04 Dec 2009 11:01

Think for yourself: how many people ask similar questions - where do you think you can get so many photos (taking into account the huge variety of models and brands of cars and the equally huge variety of breakdowns in different nodes)?

Message MAYBAX »04 Dec 2009 11:20

Message elremont »04 Dec 2009 13:29

Message MAYBAX »04 Dec 2009 14:19

Message SKORPION »04 Dec 2009 18:10

Message volna2m »04 Dec 2009 19:51

A gentleman is a person with whom you feel like a gentleman.
Repair of washing, dishwashers, sewing machines and boilers in Nizhny Novgorod

Washing machine Hotpoint Ariston of the Italian manufacturer is reliable and of high quality. But some parts of the washing machine sometimes become unusable.

You can, of course, send it to a service center for repair, but in order to save money and with skillful hands and a smart head, you can independently repair an electromechanical household appliance.

Do-it-yourself repair of the Ariston washing machine is easy to do. Follow our instructions for restoring the washing machine, and your assistant will serve you for many years.

In the Ariston electromechanical device, the main reason for the incorrect operation of the machine is blockages.
In addition, the heating element becomes unusable due to the appearance of limescale on the heating element due to hard water.
The pump can also be faulty due to its long operation.
Sometimes the filler valve fails due to damage to the rubber gasket.
In rare cases, bearings and seals have to be changed.
Electronics almost never breaks down, but we will still touch on the issue of replacing the control unit a little.

Video (click to play).

It is easy to remove the blockage with your own hands. You need to check the drain filter, which is located on the lower right under the panel.

After cleaning the filter, you will eliminate the cause of the malfunction of the washing machine. Less commonly, the drain pipe is clogged because it is thick.

There may be a blockage in the pump, but rarely, because there is an additional filter in front of it.

The drain hose will only become clogged if you have not installed it correctly.

Check the drain, there may be a blockage in it too. Disassemble the unit, pull out the branch pipe by loosening the clamps, flush it. Pull out the pump by unscrewing the fasteners and disconnecting the sensors.

Signs of a pump breakdown:

The drain pump hums, but the water does not drain.
The machine may stop when the system is running.
Water flows out slowly.

Repair of the pump of the Ariston washing machine must be done as follows:

If the filler valve is broken in Ariston, then water constantly flows into the washer, even when it is not working, it is disconnected from the network.

To check the filler valve, you need to unscrew the fasteners and remove the top cover. The valve is located where the drain hose connects to the body of the electromechanical unit.

Check the gaskets first. If they have not lost their performance, measure the resistance of the valve. Put the probes on the contacts of the filler valve and check the resistance, whether it is optimal (from 30 to 50 ohms).

If it is less or more than the set value, it means that the water intake valve is not working. To replace it, you need to unscrew the old valve from the body and screw in a new one. Be sure to connect the sensors.

If the heating element is faulty, then it is imperative to replace it. Its breakdown is indicated by the fact that the water does not heat up or washing in all programs takes place in cold water. Sometimes the machine gives an error and stops.

To replace the heating element, the rear wall must be removed. There are two contacts under the tank with a fastener in the middle. This is ten. Measure the resistance of the heating element with a multimeter.

If the resistance is within the normal range, then there is no need to change the heating element - it is serviceable. To remove the heating element, you need to unscrew the screw in the middle and pull it towards you with swinging movements.

The water may not heat up also due to the fragile connection of the wires to the heating element, which arises from the strong vibration of the washing machine. Water heating may also be absent if the temperature sensor is faulty.

Take a tester or multimeter and check the resistance of the sensor when cold and hot. If the resistance is the same, then it is broken, requires replacement. The resistance should be different.

The high-quality and durable material from which the drum of household appliances is made also becomes unusable, because solid foreign objects get into it, which can damage the unit, forming cracks on it.

The plastic rib inside the drum can deform. Remove the drum to replace it.

To remove the drum yourself, you need the following set of tools:

a set of screwdrivers, especially a Phillips screwdriver and a slotted nozzle are needed;
screwdriver;
pliers;
hammer;
hexagons of different sizes.

Use a Phillips screwdriver to remove the bolts from the back, front, and top walls, and then remove the panels themselves.

Dismantle the powder container. Use a slotted screwdriver to remove the module. It is not necessary to unscrew the control unit to the end, the main thing is that it does not interfere with the removal of the drum.

Remove the hatch cuff, pull out the lower bar by unscrewing the screws. It is necessary to dismantle electronics, shock absorbers and other parts from the loading tank.

Remove the drum from the device and disassemble it. Remove the screws holding the two sides of the drum. Pry the oil seals with a screwdriver and remove them.

The bearing in the drum can break and wear. It needs to be replaced. You only need to buy a bearing of the corresponding brand in a specialized store or order it on the official website of the Ariston washing machine, possibly purchase it in an equipment repair workshop.

Use a metal rod and a hammer to knock out the bearings. If they are defective, replace them. If the drum is deformed, replace it with a new one.

Reassemble. If the malfunction is in the plastic rib, then you do not need to disassemble the tank. The washer door is removed. A metal rod is taken, the diameter of which is smaller than the holes in the plastic rib of the drum.

The rod is inserted into one of the holes on the rib, the latch is opened with it, the plastic part is removed. A new plastic rib is put in its place. Slide along the groove with the plastic rib until the latch enters the hole and closes.

The LED indicators on the control panel receive a signal from the faulty unit. An error code is reflected on the display, indicating a breakdown of some element.

In the Ariston Margarita 2000 washing machine, in case of a malfunction, the power button starts blinking and the handle of the command device is constantly turning. The flashing pattern is different depending on the fault. The codes can be found in the instructions for the machine.

The control unit may fail due to mechanical damage, water ingress on it. Do-it-yourself repair of the control module can be done on your own only when a small part has failed or you need to replace the board completely.

In other cases, contact the service. Professionals will help you repair, rewire complex electronic circuits.

It is necessary to unscrew the screws on the board or remove the plates with a wrench, depending on its brand. Remove the control unit by replacing it with a new one. Screw in the fasteners carefully so as not to damage any part.

The price of the repair depends on its complexity. If the device does not drain the water, then the cost of restoration work ranges from 1200 to 3000 rubles.

Repair of the control module costs more than 3,500 rubles. The rattle and clatter of a typewriter can be corrected at a service center in Moscow for a price of 3,000 to 5,000 rubles.

Today we have shared with you our knowledge on how to repair the Ariston washing machine with our own hands.

We hope that you will succeed and self-repair will cost you inexpensively, you will not have to pay for disassembling and assembling washing equipment, for restoration work with the help of specialists.

Washing machines Ariston from the Italian manufacturer can be called "a model of reliability and quality", but they sometimes require attention. In some cases, repair of Ariston washing machines can be done by hand, and a specialist needs to be involved only in the most difficult cases.

Within the framework of this article, we will analyze the frequent malfunctions of automatic washing machines of the Hotpoint Ariston brand, study the "symptoms" of such breakdowns and decide how to properly make an independent repair.

The vast majority of breakdowns of Ariston washing machines are associated with their operation. This is recognized by the masters of service centers for the repair of washing machines. Sometimes we are talking about frankly incorrect operation, the user regularly makes gross mistakes, which lead to breakdown. But most often, the cause of the breakdown is the operating conditions, which the user either did not know about, or guessed, but did nothing. A striking example is hard water, which can completely disable the "home helper"!

So, what are the most common breakdowns on Hotpoint Ariston washing machines? We decided to compile a kind of breakdown frequency rating. When compiling the rating, we rely on statistical data provided by leading service centers for the repair of washing machines.

Blockages. The blockages themselves can hardly be considered breakdowns; rather, this is the cause of various breakdowns. Nevertheless, it is with blockages that craftsmen have to deal with most often, and it is strong blockages that most often paralyze the operation of various Hotpoint Ariston washing machines.
A heating element. Teng is in second place in our rating. Despite the fact that the heating element itself is of high quality, low-quality hard water does its job. Over time, the scale layer destroys even the best part and has to be replaced.
Water pump. In third place is the drain pump or pump. This part fails quite rarely and in most cases the reason is wear from prolonged operation.
Filling valve. Even less often, the filler valve fails. More precisely, not even the valve itself, but a rubber gasket. Over time, rubber dubs and begins to let water through, and this causes a malfunction. The gasket itself costs a penny, but the services of a master to replace this gasket are by no means cheap.
Bearings and seals. In fifth place are the failures of bearings and oil seals. On Hotpoint Ariston washing machines, this is a great rarity, but if such a breakdown appears, you cannot continue to operate the machine.

Important! The electrics and electronics of the Hotpoint Ariston washing machine are deliberately not included in the rating, as it breaks down very rarely.

If you have problems with blockages on the Hotpoint Ariston washing machine, do not rush to call the master, everything can be repaired quickly, with your own hands. How do you know that you are dealing with a blockage? The main sign of a blockage in the drain system is the idle operation of the drain pump, that is, it hums, but the water does not leave the tank. Usually, this trouble manifests itself after the end of the wash, the machine cannot drain the waste water to start rinsing and freezes, or it drains the water too slowly.

A strong blockage can be found in several places:

in the drain pipe, between the tank and the drain filter - this happens less often, since the pipe is quite thick;
in the drain filter - there is a blockage most often;
in the pump - in Ariston washing machines, blockages in the pump are rare, since an additional filter is installed in front of the drain pump;
in the drain hose - blockages rarely occur, mainly in cases where the hose was installed incorrectly.

How to quickly remove a blockage? First of all, you need to check and clean the easily accessible places of the washing machine, where a blockage could occur. First, we unscrew the drain filter, which is located on the Ariston machines at the bottom right under the narrow panel. Place a cloth on the filter before unscrewing it as water will drip off. Remove all debris from the filter and then screw it back on.

Next, it is important to check the drain hose and drain. In a number of situations, a banal blockage in the drain pipe can force the user to contact a machine repair specialist, when it was more correct to contact a plumber. And if everything is in perfect order, then you will need to disassemble the machine, clean the pipes and the pump. To remove the pipe, you will need to loosen two clamps, and to remove the pump, you will need to disconnect it from the sensors and unscrew the two fasteners.

If any malfunction occurs, the Hotpoint Ariston "washing machine" gives an error with a specific code displayed on the screen. It is very important to recognize the error codes of Ariston washing machines correctly, because this is a direct clue indicating the cause of the breakdown.

A broken filler valve "symptomatically" is quite difficult to confuse with other breakdowns of the Hotpoint Ariston washing machine. When the filling valve stops blocking the water, water begins to flow into the washing machine tank by gravity, even if the “home assistant” is turned off from the network.

If you hear the characteristic murmur of water being poured and drained from the tank when the machine is turned off, be sure this is a valve.

To check the filler valve, remove the top cover of the Hotpoint Ariston by unscrewing the two fasteners. The valve is located at the junction of the inlet hose with the machine body. First of all, we check the gaskets, if they are intact, then you need to measure the resistance of the device, and for this you will have to use a multimeter. We install the probes on the contacts of the filler valve and check. The meter should read approximately 30 to 50 ohms.

A defective filling valve should be replaced with a similar one; self-repair is not possible. The replacement itself is done very quickly, we unscrew the old valve from the body and screw in a new one, not forgetting to connect the sensors. It is worse if the pump is out of order, because it is a rather expensive part.

A faulty pump gives itself out during washing, when the machine should drain the water, but it does not, while the pump either does not make any sounds at all, or it hums, but the murmur of the drained water is not audible.

Note! Strictly speaking, these symptoms are superficial and they may indicate other problems (for example, with electronics), but this should give you the idea to check your pump first.

In the Hotpoint Ariston washing machine, it is at the bottom and can be reached through the bottom. It is better to check and replace the drain pump by a specialist, but you can do everything yourself, the main thing is to thoroughly study the progress of work.

The heating element is an important part of the washing machine, which is responsible for the temperature of the water in the tub, and therefore for the quality of the wash. If the heating element is faulty, the wash either does not start at all, and the system generates an error, or the wash is performed in cold water. Both should prompt you to check and replace the heating element in the Hotpoint Ariston washing machine.

Checking the heating element of the Ariston washing machine is not difficult at all. It is necessary to unfold the machine, at the bottom of the rear wall there is a service hatch, which is attached to the clips and several screws. We unscrew the self-tapping screws, and wring out the clamps with a screwdriver, after which the cover will be removed. Behind the lid, under the tank, you will see two large contacts with the fastener in the middle - this is the heating element. We unscrew the screw, and then we begin to pull the ten on ourselves, pulling it out with swaying movements.

Note! Before pulling out the heating element, it is a good idea to measure the resistance with a multimeter, perhaps the device is working properly and does not need to be touched.

As we have already noted, bearing and oil seal failures are the most rare malfunctions of Ariston washing machines. However, if this happens, then urgent action is needed. It is not difficult to recognize such a breakdown. When the bearing is destroyed, the moving elements begin to emit unpleasant sounds, the shaft begins to rub against the bushing, which leads to a depletion. If you do not take any measures and continue washing, this can lead to the fact that the drum begins to play and damage the tank.

To prevent your favorite washing machine from ending up in a landfill, you need to contact a specialist when such sounds appear, or try to change the bearings yourself. If you are determined to do the work yourself, study the information offered on our website. Otherwise, with such a complex repair, it is not surprising to make serious mistakes. The main difficulty is that in order to get to the bearings, you need to disassemble the entire washing machine, along with the tank.

In addition, it will be necessary to correctly remove the old bearings without damaging the bushing, and then install the new ones correctly so that repeated repairs are not required. Without the proper skill, not many can do self-repair, so before starting work, think about delegating it to a specialist.

In conclusion, we note that the repair of malfunctions of Ariston machines can theoretically be done by hand, especially if you have the time and patience. But all the same, in order to avoid mistakes and unnecessary expenses, it is better to turn to a specialist, because “a miser pays twice”!

Breakdowns among Ariston washing machines are an infrequent phenomenon, because manufacturers have long established their equipment as the most reliable. But still, even such an excellent technique can fail after a long time of operation. Malfunctions of the Ariston washing machine in most cases are typical and boil down to replacing the failed elements.Breakdown of heating element. Thanks to this part, the water is heated to make the washing process more efficient. If a failure occurs for this reason, the machine itself will determine this and issue an appropriate malfunction code (F03). This can be either a malfunction of the element itself, or the accompanying breakthroughs in the power circuit due to the fact that the terminals are burnt out. To eliminate the breakdown, you need to replace the burned out heating element or fix the terminals.Bearing breakage. This malfunction is typical for almost all models of cars of any manufacturer, including the ariston hotpoint model. You can see how this is done in the video or in this article:

Pump or filter faults... Regardless of vertical or horizontal loading, model range, and other indicators, it may happen that the machine refuses to drain or fill in water. The reasons may be blockages, burned out pump winding.

Sometimes, in order to get the work done, it is enough to clean the filters, if their further work is impossible, replace them. If everything is normal with the filters, but the water still does not drain, you need to replace the pump.

Most often, you need to tighten the retaining nut or change the rubber seal. Less commonly, manhole cuffs and nozzles can be the culprits. In this case, replace the problematic part.

Noise when the machine is running with reference bearings... In situations like this, check if the machine is level. If not, you need to align its placement, and to reduce the vibration level, you can put a rubber mat. If this is done and the car is still noisy, the problem may be with the shock absorbers or the tank strap.

To make repairs, you need to check these parts and, in case of breakdowns, replace the one you need. Another reason for the noise can be small objects that are caught in the drum during washing. To eliminate noise, it is enough to take out these small things. Also read this article: https://my.housecope.com/wp-content/uploads/ext/1504/prichiny-gromkogo-shuma-v-stiralnoj-mashine.html

Malfunctions of washing machines of other companies:

Ariston washing machines are equipped with a display that displays information about the washing process, mode. But there is another irreplaceable function of such a display. It will also display the malfunctions that have occurred under the fault codes. Each such code is responsible for some kind of breakdown and knowledge of their values will help to quickly determine and eliminate the malfunction that has arisen.

The following codes can be displayed on the displays of the Ariston hotpoint or aqualtis washing machines:

Knowing about the fault codes of the Ariston hotpoint washing machines, you can find the reason for stopping work. Ariston washers have a complex device, but in many cases it is possible to make repairs with your own hands, while saving time and money.

Before calling a technician, read How to Clean the Detergent Dispenser, Troubleshooting - Ariston AT 84 User Manual

Installation and use instructions

If the wash results are unsatisfactory or

Troubleshooting, read this section before calling a technician.

In most cases, you can solve the problem yourself.

Press lightly on the large

button on the front

distributor and pull out

n Is the plug inserted in the

load could be triggered by auto-

How to clean the detergent drawer

Then rinse the distributor under running water (fig. 3),

using an old toothbrush. Take out a couple of siphons, insert

compartments 1 and 2 (fig. 4) in the top, check that the

clogged and rinse.

Install a pair of siphons in

until it clicks (fig. 4, 2 and 1).

n Is the distribution too low

n On the upper floors of buildings

leaks.
Don't leave working

hole.
Always leave the door

smell.
External panels of the machine

caution.
Machine body and rubber

Before starting to repair the Ariston washing machine, a novice master should know what to check first. I'll tell you right away about the control module, this detail should be looked at only when you have checked all the main components for their performance. Below I will list, point by point, which parts you should diagnose. Many people, seeing that the lights on their typewriter blinked, immediately sin on the control module, and in fact, often the blinking of the indication indicates not a module breakdown, but a malfunction of one or another spare part. The fact is that a modern washing machine has a self-diagnostic function that displays an error code on the control panel, that is, it shows which detail it is desirable to pay attention to. You can look at the error codes of Ariston washing machines on this page, just do not be alarmed by what is written there - about Indesit. Ariston and Indesit errors are identical. Well, now let's get down to diagnostics and repair, below I will try to answer in detail the frequently asked questions that sound on my YouTube channel

Help me repair the Ariston WISL 105 washing machine. Everything works fine, but at the very beginning of the wash, when the drum starts turning slowly, the engine cannot crank it, twitches and hums, then twitches and hums in the other direction, and so on. After a few minutes, the speed turns on quickly and begins to twist, but also unwinds with difficulty. I called the master through the dispatcher. He rang the bell, the engine and the control board, everything is normal, he replaced the brushes. I turned on the washing machine, no laundry, and it worked fine. The next day the laundry was thrown and everything repeated. I call him and tell him the reason, and he told us to change the engine.I think so, if the engine grunted, it would not work at all, and so only at the beginning of the wash and moreover at low speeds, as if the engine power did not correspond to the norm. By hand, the drum spins easily and for a long time. What is the reason, can someone tell me.

What does change engine mean? First, who should change him, why did you call the master? Secondly, the motor may have nothing to do with it. Something indicates to me the failure of your master. Let's see what he should have checked first.

To summarize, I think that first of all, you need to change not the motor on the washing machine, but the master whom you invited to repair your washing machine. Of course, in your case, the engine can be so kinky, but I will say that this behavior is more typical when there is not enough voltage. In general, do what I wrote above, and then we will look at the circumstances

Video how to check a motor from a washing machine

Thanks for the informative answer, we said goodbye to the master, called another. He first of all measured the voltage, as you basically wrote. We took an extension cord, connected a washing machine to it, and with a master tester, measured the pressure. It turned out to be 180 volts, and that was the end of the repair, although they paid for the call. Yesterday my husband bought a current converter, the one that draws 220 volts from the network and tried to wash it. Everything works fine, thank you very much for your help.In general, of course, it's great that your masters settled in, like do it yourself, and I'll come and take the money. On this topic, I can also add the following, but it happens that the engine is covered, that is, some winding is a little hooked, and the control unit cannot be discounted either, but first of all, you still need to check the voltage in the network, like this to do the right thing I wrote aboveThe ariston washing machine washed normally until the last, but today they threw in the laundry and decided to wash it, they closed the hatch and pressed the start button, but nothing happens. The wash indicator and the lock signal are on, there are no buzzing sounds, and no water is being drawn into the tank. He unscrewed the water set hose from the washing machine to check the pressure, it pours no worse than from the tapThere can be many reasons for this malfunction, the fact is that almost all the details, even the pump, are responsible for the collection of water into the tank. You are probably surprised now, but now I will try to explain to you why this is happening. In modern Ariston washing machines, there is an electronic control unit that, before starting the wash, diagnoses all the components that are on your washing machine and if some part is not in working order, the module will not give a command to fill the water. Further, I will list in order those details that need to be checked, and how to check them you can find out on this page. I draw your attention to the fact that the link will take you to the repair page of the Indesit washing machine, it is practically the same unit, only the tags are different, and as for the components and repairs, everything is the same. And so let's list what you should checkI have listed almost all the main breakdowns in which there may be no water filling in the washing machine. There is only one thing left - this is the control module. If you diagnosed all the spare parts and they are in working order, then call the master. I highly do not recommend repairing the control module myself, this spare part is very complicated and can only be repaired, only a person who has some experience and knowledge, not even every telemaster is capable of making this repair with high qualityToday, our washing machine refused to drain. The first thing we did was clean the filter of the washing machine, pulled out a few coins and another clump of wool. We decided to start and wash a little, the result was deplorable, reaching the rinse, the pump refused to drain the water, but you can hear it hum. We again drained the water by hand and decided to clean the filter, but this time, there was nothing in the filter.The husband took two wires and connected them to the drain pump, in short, fed it 220v, the pump started working, the fan inside the filter is spinning. We again decided to wash and again reaching rinsing, the water remained in the washing machineAs I understand you checked everything except one, I just need to supplement your story. You did everything right, but indeed you can supply 220 volts to the pump and see how it works, then that you cleaned the filter is very good, but you also had to blow through the drain hose and wash the pipe that goes from the tank to the pump body. Very often I pull out various interesting things from this branch pipe. Sometimes socks get there, often braces, sometimes I pull out the heels. I don't need to tell you how to remove it. Now a few words, I want to say about the drain hose that is inserted into the sewer. Before purging it, be sure to unscrew the plug from the pump body, that is, the filter. The fact is that there is a plastic ball in the branch pipe that goes from the tank to the pump body, and if the filter is not unscrewed, this ball can be blown into the tank, and we cannot allow this.We did everything as you wrote. The filter plug was unscrewed, then the hose was blown through, 10 kopecks fell out of there, thinking they interfered with the drainage of the water. We also washed the branch pipe for which you spoke, there was nothing significant in it, but there was a lot of dirt. Have washed it several times, the washing machine is draining the water. Thank youIn addition to this topic, I want to talk a little about other reasons why the Ariston washing machine does not drain water. Firstly, failure of the drain pump. The fact is that this breakdown may look different, the pump winding itself burns very rarely, but the impeller often sticks. In practice, there are times when you come to a call, check the pump, everything seems to be fine, but when washing, it starts to glitch, this is due to the fact that a large output appears on the impeller rotation mechanism, it also happens that a coin or some other thing gets under the impeller is nonsense that you can not even see, so you need to check well with your finger or something else, if there are any foreign objects under the impeller. It happens that a thread is wound around the impeller, this also affects the operation of the drain pump. In general, it is necessary to check everything related to the passability of the hoses and the performance of the pump. If all this does not help, then you need to look at the module, but before that, be sure to check the wires that go from the module to the pump, they are often broken. From experience I can say that the control module, with such a breakdown, breaks down extremely rarely, therefore the brain is the very last detail that you need to climbWe have a Hotpoint Ariston - Aqualtis washing machine. Recently, the bearings rustled, at first there was a small hum, and then the noise began to increase, there is also a play on the drum. In the workshop, we were asked too much money for repairs, we simply do not have that kind of money. On your YouTube channel, I watched a video in which you change bearings in the Indesit washing machine and I have a lot of questions. What is the difference between the tank of the Ariston Hotpoint - Aqualtis washing machine from the tank in your video. In particular, I am interested in: whether or not it is necessary to cut the tank, which company of bearings for the washing machine is better to use, which lubricant for the oil seal should be bought. If you cut the tank, what kind of glue is needed to glue the two halves and what is the best way to fix it - with self-tapping screws or boltsIn fact, the petition was two pages long, I just chose the most necessary of everything that a visitor to my channel wrote, he really had too many questions. Below you can watch a video, which tells about all the nuances of replacing bearings in a washing machine, and now, in order, I will answer the questions that were asked to meThe site has a detailed article on grease and oil seal, everything is described in detail there and be sure to watch the video belowTo glue the tank, I use a Dragon sealant for cars.For fasteners, I mainly use self-tapping screws, on my channel they made comments to me that self-tapping screws can be unscrewed, more than one hundred guys have already done this. I use bolts only where the screws are scrolled. It happens that the tank comes back for repair, in which case bolts can be used. In the video below, I talk about all the nuances of such a repair, it shows what kind of glue I use, what kind of lubricant, and so on.