Ariston tx100 ex DIY repair

Details: ariston tx100 ex do-it-yourself repair from a real master for the site my.housecope.com.

no water inlet (valve resistance is approximately the same
3 kOhm) the light is on, when installed on the drain - the pump works, when installed on the spin cycle - the pump works and the drum does not turn.

valek31, and where did you “dig” at all? What is "accumulated"? Did you read the rules?

valek31, try to go through the ports of the processor with a signature analyzer

That's why I'm asking because I don't know where to dig, what to look for. I removed the collector motor control board - I didn’t see anything worthy of attention on it. I didn’t look at the brushes, but I turned on the motor from the thyristor regulator - the motor turns. ten - it rings, there is no leakage on megohms to the case. Although in my opinion in this case it was all in vain. I would like to be told what to look for in such cases.

I would like to know - faulty engine meters can give such a defect (the motor was not removed because they asked for a set of heads for the weekend, and then, as an evil, an urgent client)

I mean the old one which is given by reference

Eh valek31, valek31, and how not to swear at you (“trowels”) after this.
UBL does not work for you, and you are already trying to finish off the motor control module and the motor itself.

regiss, why poke your finger like that right away, if valek31 does not know how any SMA starts - let him pick the module with the engine. It took me 2-3 weeks ago to repair such a machine with the same malfunction with a smoke break

So after all, someone, with their tips, produces such “craftsmen”.

constant, probably at regiss, very good mood was. Is it him? Doesn't look like himself

Video (click to play).

the fact is, gentlemen, that the UBL was inspected first, the inspection showed that it had been disconnected for a long time, and the contacts were short-circuited (sorry, I forgot to say).

although of course thanks, I used to think that if UBL didn’t work, then nothing would work at all.

it was this delusion that prompted me to all the other meaningless checks that seemed ridiculous to you (probably for many, if you don’t already know where to dig, then you consistently check everything). but not everything is as pointless as it might seem at first glance, on the control board of the collector motor, both relays had dry solder joints, the contacts on the motor along the tacho circuit were heavily oxidized. I understand, of course, that the respected SHAITAN would hardly bother himself with such checks with these symptoms, all the more so he would remove the engine to view the condition of the brushes. But many customers ask, in addition to repairs, to diagnose the car, and we charge them money for this (as it will not be funny to some), but I’m sorry for my misconception, I confess that I didn’t know and didn’t check this circuit in more detail, because I saw that the sunroof was turned off (and before that she worked for them)

Multifunctional Italian units from this company are considered very popular due to their ergonomics and reliability, but they can also fail. Failures in SMA Ariston are rare phenomena, since the manufacturer guarantees the reliability of his product. But there are several typical cases involving the replacement of failed elements. In such situations, it is quite possible to repair Ariston washing machines on your own. The intervention of experienced specialists will be required only in particularly difficult cases.

The vast majority of Ariston machine failures are caused by their operation. This opinion was reached by the masters of services providing repair services. Sometimes problems are caused by outright violations of the operating rules, but the environment in which the machine is operated should not be discounted.

A well-known brand has found its niche in the market.But, like other models, the washing machine is prone to minor breakdowns, which most often occur due to careless handling of the device. The point is that each element has a certain working resource. For example, the brushes of an electric motor without replacement can last about twelve years. During this period, they wear out and need to be replaced. A little earlier, the drive belt loses its performance, which also changes, for which you will have to disassemble the washing machine.

For some failures, Ariston washing machines can be repaired on their own, without the intervention of service center specialists. Some of the simpler and more common failures include:

the washer does not turn on;
waste water is not drained;
washing water is not heated;
the drum has stopped rotating;
during the operation of the machine, a crunch and rattle are heard.

For more serious questions, it is recommended to call the master.

The failures listed above can occur for certain reasons, which you can eliminate with your own hands.

If there is a similar problem, do not rush to call the master. The main symptom of this problem is the idle operation of the pump, the lack of water drain. As a rule, this problem happens after washing, the machine does not drain the water to switch to rinsing, or it does it too slowly. A blockage can form at certain points:

in the drain pipe located between the filter and the tank. It rarely happens, because the nozzle is thick enough;
in the water filter. In this place, blockage occurs most often;

in the pump. For a machine of this brand, blockage in this place is rare, because another filter is mounted in front of the pump;
in the drain hose. A rare occurrence that can be caused by improper hose installation.

When removing a blockage, you must first inspect and clean the most accessible places of the washer. First of all, the drain filter is unscrewed, located in the lower part on the right, behind a narrow panel. Before you start unscrewing the filter, you need to put a rag to collect spilled water. After cleaning the filter from debris, it can be put in place.

The second step is to check the drain hose. It is unscrewed and cleaned with a cable. After that, the hose is installed in its place.

If the problem persists, you will have to disassemble the machine to clean the pump and pipes. To remove the pipes, a pair of clamps is released, and when dismantling the pump, disconnect the electrical wiring and unscrew the mounting screws.

Failure of the pump and water intake valve.

A broken water inlet valve, by all indications, is quite difficult to confuse with other washing machine malfunctions. When this element ceases to close the flow of water, it enters the tank by gravity, even when the machine is de-energized from the mains.

If you hear the characteristic murmur of flowing and draining water when the unit is turned off, you can be absolutely sure that the problem lies precisely in the valve.

To check this element, you should remove the top panel, which requires unscrewing a couple of bolts. The valve is located at the point of connection of the hose intended for collecting water with the SMA body. First you need to check the gaskets, then measure the resistance of the device using a multimeter. To do this, the probes are exposed to the contacts of the intake valve, and a check is performed. A value of 30 - 50 ohms should be displayed on the device.

The failed element must be replaced with an analogue, it is no longer subject to repair. The replacement process is quite fast. You just need to unscrew the old element, and install a new one in its place, connecting all the sensors.

The problem arises with a failed pump, since such a part is quite expensive. A failed pump will give itself away during the washing process, when the unit should drain the waste water, but this does not happen.At the same time, no sounds are heard from the pump, or it buzzes idle, and the murmur of flowing water is not heard.

It should be noted here that such signs are considered approximate and may well confirm that there are problems of a different nature. For example, the electronics failed. And yet, first of all, you need to check the pump.

In Ariston, it is located below, it is possible to get to it through the bottom of the machine. It is necessary to entrust the master to check and change the pump, but some craftsmen do this work on their own.

Failure of the water heating element.

The heating element is considered an important part, which is responsible for maintaining the temperature of the water in the tank, respectively, and for the quality of the washing process. If it breaks, washing may not start at all, an error code will be displayed on the screen, or washing will start in cold water. Both phenomena should cause you to inspect the heating element, check it for operability and, if necessary, replace it.

The verification is fairly easy. It is necessary to deploy the washing machine, on the back panel from the bottom, find a service hatch, fixed with latches and self-tapping screws. After unscrewing and squeezing the fasteners, remove the cover. Under the tank are two contacts fixed in the middle. The screw must be unscrewed, then the heating element is carefully pulled towards itself. At this point, it can be gently rocked in different directions.

It is recommended that before removing the heating element, check its resistance using a multimeter.

If, however, the heating element is burned out, it is replaced with a similar one. Installation is carried out in reverse order.

Bearing failure.

It is no longer a secret that the failure of oil seals or bearings is a rather rare phenomenon in Ariston. But sometimes this happens, and appropriate measures must be taken immediately. Such a breakdown is recognized quite easily - in the bearing, after its destruction, all rubbing elements make unpleasant sounds, the shaft rubs against the bushing, forming a wear. If you do not take appropriate measures and continue to use the washing machine, play will appear in the drum, which will damage the tub.

So that the machine does not break down completely, you should, having heard such sounds, immediately call the wizard, or make an attempt to replace the bearings on your own. The main difficulty lies in the fact that you have to disassemble the washer. Bearings must be removed so as not to damage the bushing, install new elements in the vacated space. And here, due skill will already be required, otherwise the repair will not bring positive results.

Washing machine does not turn on.

This problem can arise from a faulty outlet or power wiring. The first option is easy to check - just turn on another electrical appliance. If it works, then disconnect the wire that feeds the machine and check it with a tester. If the wire is in good condition, it is necessary to look for a problem in the control unit. This is a more serious problem, involving the intervention of an experienced specialist.The first thing that draws attention is the condition of the drive belt. During the operation of the machine, it is subject to severe wear and tear. To such problems, you can add a gap or an increase, which is also not very pleasant. In each of these cases, it is necessary to replace the drive belt. Such repairs do not cause any particular difficulties, it is quite possible to carry out on their own. Image - Ariston tx100 ex DIY repair

It should be noted that the belt is not considered the only cause of such a failure. A few more troubles can happen related to the failure of the electric motor, a breakdown in the control unit, malfunctions of the electrical wires, blockages in the filter. Each of them can cause the rotation of the drum to stop. Only an experienced master can determine it.

Breakage of fasteners.

It may happen that the door in the machine stops closing or is tightly fixed.The problem should be sought in its skew, which does not allow the hook to enter the hole intended for it. To fix this problem, you just need to tighten the door hinges. When the locking tab wears out or the handle loosens, these elements are best simply replaced.

Repair of the control module, or its replacement.

In order to remove this element, it is necessary to sequentially perform several actions:

it is necessary to de-energize the washing machine by pulling the plug out of the socket;
remove the top panel of the machine;
by pressing on a special latch located in the center, remove the box for detergents (dispenser);
now the front panel is unscrewed, the clamps are unclenched, the board is turned off;
the selector is removed, a new board is mounted on it;
it remains to assemble in the reverse order and check the machine for operability.

Remember that there is nothing complicated here. But checking and cleaning oxidized contacts is much more difficult.

The manufacturers of the Ariston washing machine took care of the future owners of their product, providing it not only with modern functionality and beautiful design, but also with a convenient system for self-diagnosis of faults. Codes indicating malfunctions light up on the display of the machine. For some models, a failure may be indicated by a flashing indicator on the panel.Without a doubt, the Ariston washing machine has a complex structure, but most often, having information about errors and breakdowns, it is possible to find their cause without any problems and carry out repairs on our own, without using the help of qualified specialists. It is only recommended not to neglect technical advice, to comply with every last detail, and to comply with safety requirements. Image - Ariston tx100 ex DIY repair

Washing machine Hotpoint Ariston Italian manufacturer-reliable and high quality. But some parts of the washing machine sometimes become unusable.

You can, of course, send it to a service center for repair, but in order to save money and with skillful hands and a smart head, you can repair an electromechanical household appliance yourself.

Do-it-yourself Ariston washing machine repair is easy to do. Follow our washing machine restoration instructions, and your assistant will serve you for many years.

In the electromechanical device Ariston, the main reason leading to incorrect operation of the machine is blockages.
In addition, the heating element becomes unusable due to the appearance of limescale on the heating element due to hard water.
The pump is also faulty due to its long operation.
Sometimes the filling valve fails due to damage to the rubber gasket.
In rare cases, it is necessary to change bearings and seals.
Electronics almost never break, but we still touch on the issue of replacing the control unit a little.

It is easy to remove the blockage with your own hands. You need to check the drain filter, which is located at the bottom right under the panel.

By cleaning the filter, you will eliminate the cause of the washing machine malfunction. Less often, there is a blockage of the drain pipe, because it is thick.

The pump may be clogged, but rarely, because there is an additional filter in front of it.

The drain hose only becomes clogged if you installed it incorrectly.

Check the drain, it may also be clogged. Disassemble the unit, pull out the pipe, loosen the clamps, rinse it. Pull out the pump by unscrewing the fasteners and disconnecting the sensors.

Signs of a pump failure:

Drain pump hums but water won't drain.
The machine may stop while the system is running.
Water flows out slowly.

Ariston washing machine pump repair should be done as follows:

If the filling valve is broken in Ariston, then water constantly flows into the washer, even when it is not working, it is disconnected from the network.

To check the fill valve, you need to unscrew the fasteners and remove the top cover. The valve is located where the drain hose connects to the housing of the electromechanical unit.

Check gaskets first. If they have not lost their performance, measure the resistance of the valve. Put the probes on the contacts of the filling valve and check the resistance if it is optimal (from 30 to 50 ohms).

If it is less or more than it should be, it means that the water intake valve is not working. To replace it, you need to unscrew the old valve from the body and screw in a new one. Be sure to connect the sensors.

If the heating element is faulty, then it must be replaced. Its breakdown is signaled by the fact that the water does not heat up or washing according to all programs takes place in cold water. Sometimes the machine gives an error and stops.

To replace the heating element, the rear wall must be removed. Under the tank there are two contacts with a fastener in the middle. This is the ten. Measure the resistance of the heating element with a multimeter.

If the resistance is within the normal range, then you do not need to change the heating element - it is serviceable. To remove the heating element, you need to unscrew the screw in the middle and pull it towards you with rocking movements.

The water may not heat up due to the fragile connection of the wires to the heating element, which arises from the strong vibration of the washer. Water heating may be absent even if the temperature sensor malfunctions.

Take a tester or multimeter and check the resistance of the sensor cold and hot. If the resistance is the same, then it is broken and needs to be replaced. The resistance must be different.

The high-quality and durable material from which the drum of household appliances is made also becomes unusable, because solid foreign objects get into it, which can damage the assembly, forming cracks on it.

The plastic rib inside the drum can be deformed. To replace the drum, you need to remove it.

To remove the drum yourself, you need the following set of tools:

a set of screwdrivers, especially a Phillips screwdriver and a slotted nozzle;
screwdriver;
pliers;
hammer;
hexagons of different sizes.

Using a Phillips screwdriver, the bolts are removed from the rear, front and top walls, and then the panels themselves are removed.

Remove the powder container. Remove the module with a slotted screwdriver. The control unit does not have to be unscrewed to the end, the main thing is that it does not interfere with removing the drum.

Remove the cuff of the hatch, pull out the lower bar by unscrewing the screws. From the loading tank, you need to dismantle the electronics, shock absorbers and other parts.

Remove the drum from the device and disassemble it. Remove the screws holding the two sides of the drum. Pry off the seals with a screwdriver and remove them.

In the drum, the bearing can break and wear out. It needs to be replaced. You only need to buy a bearing of the appropriate brand in a specialized store or order it on the official website of the Ariston washing machine, or purchase it at an equipment repair shop.

Use a metal rod and a hammer to knock out the bearings. If they are faulty, replace them. If the drum is deformed, then change it to a new one.

Reassemble. If the malfunction is in the plastic rib, then there is no need to disassemble the tank. The washer door is removed. A metal rod is taken, the diameter of which is smaller than the holes in the plastic rib of the drum.

The rod is inserted into one of the holes on the rib, the latch is opened with it, the plastic part is removed. A new plastic rib is put in its place. Move the plastic rib along the groove until the latch engages the hole and closes.

The LED indicators that the control panel is equipped with receive a signal from a faulty unit.An error code is displayed on the display, indicating a breakdown of some element.In the Ariston Margarita 2000 washing machine, in the event of a malfunction, the power button starts flashing and the handle of the command device constantly rotates. The nature of the flashing is different depending on the fault. The codes can be found in the owner's manual. Image - Ariston tx100 ex DIY repair

The control unit may fail due to mechanical damage, water ingress on it. Do-it-yourself repair of the control module can be done on your own only when a small part has failed or you need to replace the board completely.

In other cases, please contact the service. Professionals will help you repair, resolder complex electronic circuits.

You need to unscrew the screws on the board or remove the plates with a key, depending on its brand. Remove the control unit, replacing with a new one. Screw the fasteners carefully so as not to damage any part.

The price of the repair depends on its complexity. If the device does not drain the water, then the cost of restoration work ranges from 1200 to 3000 rubles.

Repair of the control module costs more than 3500 rubles. The rattle and knock of the machine can be fixed at a service center in Moscow for a price of 3,000 to 5,000 rubles.

Today we shared with you the knowledge of how to repair the Ariston washing machine with our own hands.

We hope that everything will work out for you and self-repair will cost you inexpensively, you will not have to pay for disassembly and assembly of washing equipment, for restoration work with the help of specialists.

Models of Hotpoint and Margarita washing machines from the Italian manufacturer Ariston are rightfully considered one of the most reliable, ergonomic and high-quality among numerous competitors. However, even with them, sometimes unforeseen failures occur, which can be completely eliminated with your own hands.

Before you start repairing the machine, you should first figure out what most often malfunctions lead to the failure of the unit and determine the code of possible malfunctions.

The stability of the Ariston machines, first of all, depends on their correct operation. If there are certain problems, then you can try to fix them on your own, without resorting to the help of a specialist. But for this you need to figure out what most often can cause malfunctions.

Perhaps one of the most common causes of problems in the operation of the machine is blockages that prevent the passage of water during the process of draining it, which, in turn, leads to the inability of the washer to reconfigure the rinse mode. Characteristic signs of this problem are idling, loud noise and the impossibility of passing water through the hose (or very poor water permeability). As for places of blockage, then they can be concentrated:

in the drain hose itself, and in most cases blockages occur if it is installed incorrectly;
often blockages form in the drain filter itself;
blockages may occur in the pipe, which is located between the drain filter and the tank;
and also in the pump, although this is an extremely rare practice.

In order to correct the situation and eliminate the malfunction, it is enough to clean the machine from blockages in accessible places (pump, hose, drain pump or pipe).

The second problem that can be encountered during the operation of Ariston machines is lack of water heating during the erasing process. Often, in such a situation, the washing machine can be shocked due to dysfunction of the insulation of the heating element.

The main reason that provokes such a malfunction is extremely hard water, resulting in the formation of scale. Repair consists in replacing a damaged electric heater (heater). To do this, unscrew the back panel of the machine, since it is behind it that the fastener of the broken electric heater is located. First, disconnect all contacts and unscrew the fixing screw, then carefully pull out the broken heater and replace the part with a new one. Everything, the malfunction is fixed, and the machine should heat the water, as before.

The most difficult problem is the breakdown or partial wear of the bearing or seal at Ariston. Fortunately, in practice, it is extremely rare.

To understand that machine malfunctions are result of bearing failurejust pay attention to the following signs:

during the operation of the unit, all moving elements of the washer begin to make characteristic sounds during the spin cycle;
in this case, the shaft begins to come into contact with the sleeve;
vibrations are possible.

It must be said right away that this problem should be removed promptly, because otherwise you can just break the machine. The only difficulty is that the repair will require almost complete disassembly of the machine. Therefore, if there is no confidence in your actions, it is best to entrust this process to a professional.

In this case, most likely there is a malfunction associated with socket or power cord. To check the operation of the outlet, just try turning on another electrical appliance. If everything is in order with the outlet, then you need to check the wire itself. To do this, it must be disconnected from the outlet and try to “ring” with a special tester.

In the event that the electrical wire is normal, then most likely the problem is hidden directly in the power supply of the machine. This is a rather complex problem, so only an experienced professional can solve it.

It is interesting! How to open the washing machine yourself if it is blocked

Another problem that can cause the machine to stop working is no drum rotation. There are several reasons that can cause such a situation: engine breakdown; problems with electrical wiring; collection in the operation of the control panel or clogging of the filter. However, the most common cause is wear or severe stretching of the belt. In this case, you need to replace it - there should not be any special problems with self-replacement.

If the reason is different, then it is best to call a professional at home to identify the cause of the breakdown of the machine.

An equally common problem that users of Ariston Hotpoint or Margarita typewriters may encounter is a malfunction that occurs directly in the control unit. The main reason for this problem is a malfunction of our electrical networks, which is extremely problematic to deal with on our own.

In this case, the problem is easier to prevent than to fix. Therefore, before you start operating the washing machine, in particular, Ariston, it is best to put special protective equipment, which help protect the washer from power surges and other similar failures. This approach will be much more efficient and economical than replacing the entire control unit.

Operational problems may also arise during loose or broken mechanical fastenerswith which the machine is equipped. Most often, this is expressed in weakening the fixation of the hatch of the machine. The problem has the following symptoms: strong noise during the operation of the washer and characteristic vibrations. To get rid of this, it is enough to tighten or completely replace the fasteners with new ones.

It should be noted that such models of Ariston washing machines as Margarita 2000, Hotpoint, Avsl 109 and others have unique self-diagnosis function. The bottom line is that the system independently detects a malfunction and shows on the display or by flashing indicators, its specific code. Having an idea of what code number the unit shows, you can independently identify the problem and fix it.

It is interesting! Reasons why the washing machine does not draw water

Having an idea of \u200b\u200bwhat most often failures can occur in Ariston typewriters, you can try independently repair the unit. However, it should be started only if there is confidence in their actions. If there is no experience in such things, it is best to entrust the repair of the washer to a specialist.

Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Please, do not make a copy of the downloaded manual and do not offer to sell it,
just use personally to repair defective appliance! Good luck to the repair!

There is no preview for this item!

Video (click to play).

Possible causes:

this is not a pdf file.

The practice of recent years has shown that it is possible to repair the Ariston washing machine with your own hands.

Each master who repairs complex household appliances undergoes a special training course.

As part of this course, the functional and schematic diagram of the Hotpoint Ariston washing machine is studied.

At present, this machine is very popular with consumers. This is due to the versatility of the washing machine and ease of use.

In almost every major city and even in rural areas there are service centers for the maintenance and repair of these units.

Hotpoint Ariston washing machines appeared on the home appliance market many years ago. Today, analysts have almost eighty models that successfully perform their functions.

Each new model carries an additional feature that facilitates the washing process or makes it better.

Among the advantages of the models of this brand, the following should be noted:

high quality washing;

noiselessness;

operational safety;

ergonomic design.

With ease of operation and high reliability, the repair of Ariston machines requires a consistent and accurate approach.When the Hotpoint Ariston washing machine installed in the bathroom performs its functions properly, very often no maintenance actions are performed.And only when some malfunctions occur, attention is paid to the condition of the machine. In order to determine the nature of the breakdown, you need to imagine the general scheme of the unit.If you draw a simplified diagram of a washing machine, then it will consist of the following components and assemblies:

tubular electric heating element - heating element;

Electrical engine;

drain pump - pump;

water inlet valve;

bearings and seals;

sensors and timers.

This is an incomplete list of devices that make up the Hotpoint Ariston washing machine.However, it gives an idea of how the machine works and what connections exist between individual devices and mechanisms.Initially, any model is designed in such a way as to save water and electricity. Particular attention is paid to the consumption of detergents.All these resources are combined in such proportions to provide a gentle washing regime. Products from different fabrics are erased in different ways.Washing modes are set using special sensors and control devices.Self-repair of the washing machine should begin with an assessment of the malfunction.When the machine is working normally in all modes, but the quality of the wash is declining, and the spinning is practically not performed, you need to inspect the drain hose.The used water enters the hose through the outlet filter. The video shows the procedure for removing and cleaning the filter. This is a standard operation.