Details: beko wmn 6508 k do-it-yourself repair from a real master for the site my.housecope.com.
Message stasprachkis » Jun 05, 2011 01:01
Message Maftun » Jun 05, 2011 09:24
Message bun » Jun 05, 2011 09:27
Message Maftun » Jun 05, 2011 13:01
Message elkri » Jun 05, 2011 13:13
Message Maftun » Jun 05, 2011 14:19
One was not enough but knocked out. Now it remains to knock out the bearings.
Message Maftun » Jun 05, 2011 15:35
I ran into another problem after removing the control panel trim. accidentally turned the washing program control knob, what to do now when assembling, how to find out what washing mode the machine is on.
Message wave2m » Jun 05, 2011 15:39
A gentleman is a person with whom you feel like a gentleman.
Despite the fact that imported washing machines have served flawlessly for more than 10-15 years, users quite often turn to service centers to repair Beko washing machines.
In most cases, the problems are mild, so we suggest considering cases where you can easily carry out repairs yourself.
Having entrusted the inspection of the car to an experienced master, there is no doubt that he will quickly and professionally find what the problem is. But due to the high prices for services, many home craftsmen are trying to save money and do their own Beko washing machine repairs.
Almost any CMA model can be repaired at home: ELB 57001 M, RKB 58801 MA, LNU 68801, etc.
This approach is fully justified - often repairs cost exorbitant prices, and sometimes the price is such that you can buy a new machine. At the same time, even the most "killed" car can last a few more years after repair.
Video (click to play).
Do not want to throw away the Veko machine and buy a new one? Try to figure out the problem yourself and fix everything with your own hands.
The device of the Beko washing machine also determines the nature of its breakdowns. Consider the typical malfunctions of washing machines of this brand:
Water does not heat up to the set temperatures, washing goes in cold water on any program. Or vice versa - the water overheats.
The tank fills slowly with water or does not fill at all.
The Beko washing machine does not start because the door does not close tightly enough.
Water is in the tank at the end of the wash (this may be accompanied by a strong hum).
The rotation of the drum occurs with a rattle, rumble, clang and other uncharacteristic sounds.
Not a single washing mode starts - all the lights on the machine blink. Or the program works, the indicator lights up, but the machine does not erase.
I cannot start the machine with the power button (when the power cord is connected to the mains).
Models with an electronic display give error codes H1, H2, H3, H4, H5, H6 and H7. The machine is not working.
Important! There may be other signs of failure. We have reviewed the most common Beko SM users in Russia.
As mentioned earlier, all malfunctions are accompanied by certain signs - from minor malfunctions to complete failure. The problem of a home master always lies in one thing - how to connect the existing signs of a breakdown with its causes. Here you just need the knowledge and advice of narrow specialists.
Next, we briefly summarize the main breakdowns.
If you know how to use a Beko washing machine, then you know that the water used after washing is never clear and clean - this is the specificity of washing. So that dirt, threads, hair, etc. do not clog the pump, there is a special drain filter on the way to it, which mainly suffers from blockages.
Your task is to find this filter, which is usually located at the bottom of the washer, under a small hatch or behind a panel. How to proceed next:
Before removing the filter, do not forget to substitute a basin or lay a rag under the machine, because the rest of the waste water will surely pour out of the hole.
In a number of Beko models, along with the filter, an emergency drain hose is also included - with its help it is much more convenient to drain water into any container.
To remove the filter, simply turn it to the right.
Next, clean the filter by hand and rinse under a faucet.
Armed with a screwdriver, you can also clean the pipe at the same time - it is usually also clogged with debris from waste water.
Once you have tools at hand, do not rush to put them away - for prevention, clean the filter that is on the water supply (it is located at the place where the hose is attached to the rear panel). Sand and rust from the plumbing slowly collect in this filter and eventually interfere with the normal filling of water into the drum.
After cleaning the inlet filter, do not rush to put it in place - also check the drain pump. Often, Beko washers, during self-diagnosis, find a pump failure and signal this using the H5 fault code. But with some breakdowns, the controller may not see minor violations - such as a loose impeller (you can identify it by hearing a hum).
To check the pump, start the drain mode and look into the filter plug hole to see how the impeller behaves. If it rotates, then everything is in order, and if not, then you need to clean or even replace the pump.
To fix this problem, you will also need at least a partial disassembly of the Beko washing machine, but more on that below.
First, let's say that in SM one of the most vulnerable nodes is a thermoelectric heater, simply a heating element. The mineral salts present in the water under the influence of hot water crystallize and settle on the heater in the form of a familiar scale - like in a teapot. Plaque does not let heat through, so the heating element does not give it to water and burns out.
If there is no scale, you have soft water, or you use special products, this does not mean that the heater could not burn out. The heating element has its own generation resource, and maybe its time has just come.
If the heating element fails, you will know about it by the errors H2 and H3. To be 100% sure what happened to him, first get to the heater. In some Beko models it is at the back, in others it is in the front.
So, how to disassemble the Beko washing machine, find the heating element, check and replace it, read on:
If the heating element is in front, then in order to remove the front panel, you need to remove the cuff of the hatch. To remove it, proceed carefully - if something goes wrong, then your activity is fraught with damage to the cuff and leaks.
You will not see the entire heating element - only its shank with two contacts and wires going to them.
Disconnect all wires.
Take a tester and measure the resistance. Usually, 25-30 ohm marks will be normal. If the indicators are different (for example, infinity), then there is a breakdown.
Remove the heating element by unscrewing the nut from the bolt that holds it under the drum.
Clean the installation site from debris and plaque.
Install the new heating element in reverse order, connecting all the wiring in place.
This video shows in strict sequence how to remove, check and replace the heater:
VIDEO If the heating element turned out to be inactive, then you need to check the temperature sensor (thermistor). You will find it under the top cover. How to get and test the sensor:
Remove the top cover by unscrewing the screws.
The dismantling of the sensor is carried out with the removal of the cuvette for detergents and the control panel - all this makes it difficult to get to the element. Having reached the sensor, free it from the wires.
The resistance measured by the tester in room conditions should be 4.7 kOhm.
Heat the sensor in a glass of warm water - after that, the readings should drop. If this does not happen, the sensor needs to be changed.
Installation of a new sensor is carried out in the same way as dismantling, only proceed in reverse order.
If you have the knowledge and experience of repairing electrical appliances, then you will quickly eliminate breaks in contacts or their oxidation. You only need a diagram of the Beko washing machine - you will find it in the manual or on the manufacturer's website, indicating the model of your SM.
As for electronics, everything is ambiguous here.
Repair or replacement of the electronic controller (control board) requires special knowledge and extensive experience.
Considering that an electronic module can cost as much as a third of your washing machine, it is not profitable to engage in amateur activities. Especially if the board needed minor repairs, which any master can do for little money. If you "sentence" the module, you will have to buy a new one, and an innocent breakdown will end in a complex and expensive repair.
Remember that it does not matter what characteristics your machine is designed for - they break in exactly the same way. If you got a 5 kg Beko washing machine, the malfunctions will be the same as in a similar 3 kg model. To prevent the Beko automatic washing machine from breaking down, we advise you to use the instruction manual and follow the rules prescribed there.
Frequent malfunctions of the BEKO WMN 6508 K washing machine:
VIDEO
Call a master to repair a washing machine in St. Petersburg:
+7 (812) 612-38-18
Our company produces repair of washing machines at home in St. Petersburg. We employ only highly qualified craftsmen.
Call a master to repair a washing machine in St. Petersburg:
+7 (812) 612-38-18
A fairly common problem is the chafing of the hatch cuff, water seeps into the hole, and given the tight contact of the internal parts, it reaches the UBL, you will have to change both the cuff and the UBL. It should be understood that the work of the master can stretch for the whole day, because in many washing machines, in order to change the bearing, you will have to disassemble the equipment by screw. In general, the replacement of any part is difficult, since the elements and nodes are located in close quarters, you need to work almost blindly. It should be noted that the cost of work varies from breakdown and time costs of a specialist. Replacing bearings sometimes takes 40 minutes, and sometimes up to 6 hours. The price is determined by the master after a thorough diagnosis. The installed parts are guaranteed within 3-12 months, it applies to parts replaced during the repair, as well as the work performed. In the event of a repeated breakdown of the replaced part, the master will perform the work again - completely free of charge.
The cost of repairing washing machines consists of the cost of labor and the cost of spare parts. Spare parts have different prices for different brands and models, and even for the same brand, the cost may be different. For example: for a Bosch washing machine, a cuff can cost from 1500 rubles. up to 8000 rubles. It all depends on the model and region of production of the washing machine.
You can download the washing machine manual for free BEKO WMN 6508 K in Russian at the link below or view the instructions in the browser.
If you have any additional questions on the use or repair of the BEKO WMN 6508 K washing machine, you can ask them in the comments at the bottom of the page or in the FAQ section.
But in some cases, the problem is not so serious, it can be eliminated with your own hands, thereby extending the age of your beloved “home assistant”. That is why we will talk in this article about typical breakdowns and repairs of Beko washing machines.
Experienced washing machine repair specialists are able, by looking at the operation of the equipment, to determine which unit or element is broken or is about to break and needs to be repaired.It would seem that if there are problems with your machine, call such a specialist from the service center, and he will deal with the cause of the breakdown, and if you're lucky, he will fix it on the spot. Everything is fast, easy and without unnecessary headaches, and most importantly, in some cases such an act is fully justified.
But there is one “but” here, calling a master and his repair services cost money, and a lot of it. It often happens that repair services cost more than the real cost of a Beko automatic washing machine and machines of other brands. It's a shame to give that kind of money for old junk, especially if there is no way to quickly buy a new machine. There is only one way out - to try to fix the breakdown with your own hands. But for this, you need to correctly identify the breakdown, which will be helped by the “symptoms” of malfunctions of Beko washing machines.
The water is not heated, and washing takes place in cold water or, on the contrary, the water is heated very strongly, not in accordance with the temperature set by the user.
Water is poured into the tank for a very long time or is not poured at all.
The hatch does not close completely and because of this, the wash does not start.
After the wash is completed, the water does not drain and this is accompanied (or not accompanied) by a strong hum.
The drum of the Beko washing machine rotates with a strong rattle, clang and other extraneous sounds.
It is not possible to start any washing program, because the machine, after turning on, blinks all the lights or the program is set, but does not start.
The machine does not turn on with the button, although the power cord is plugged into the outlet.
The Beko machine, which has a display, gives an error code and "refuses" to work.
Note! There may be more symptoms of malfunctions, but most often users have to deal with the above.
As we noted above, malfunctions of washing machines give themselves out as external “symptoms” of malfunction or failure altogether. But the problem is, how can these symptoms be associated with a specific breakdown? This is where some knowledge and advice from experts will be required, let's briefly outline them.
this may indicate a breakdown of the heating element or control board. The same conclusions can be drawn if the water is constantly overheating, that is, the user sets the temperature to 30 0 C, and the system brings it almost to a boil. In case of water overheating, the probability of a malfunction of the control board is even greater than a malfunction of the heating element, but both elements must be checked.
When you start the washing program, the machine should start pouring water into the tub. This happens with varying intensity, depending on the program selected by the user. To see the process of filling the water, just look through the window of the hatch. But if you see that 20-30 or even 40 minutes pass, the drum slowly rotates, but the water does not enter the tank, or time passes and the machine freezes, stopping executing the program and issuing a certain error code. There may be four reasons for this:
there is no water in the water supply system - this fact is easy to check by opening any tap;
the water filter located at the base of the inlet hose (if any) is clogged, respectively, water does not enter the machine;
the filling valve is broken;
Faulty element of the control unit.
The Beko automatic washing machine is designed so that it will not start the washing program until the hatch is completely closed and the blocking device sensor sends a corresponding signal to the control board. If the hatch does not close or seems to be closed, but the washing program still does not activate, then either the locking device has broken and does not hold the hatch, because of this, the sensor cannot work, or the sensor itself has broken.
For your information! If there is a problem with the hatch blocking device, try to gently press this hatch with your knee and turn on the washing program again, it is possible that the fixing hook simply does not fully enter the mating part and fixation does not occur.
in the pump;
in the control board;
clogged drain hose or drain.
If the machine is very noisy, the drum rotates with a terrible clang, rattle and knock, it is very possible that the bearings have broken or just a foreign metal object got into the tank, got stuck between its wall and the wall of the drum and wedged. Such a breakdown requires the immediate shutdown of the machine and the adoption of measures to eliminate the problem.
Also, the machine may not turn on at all or, after turning on, start blinking all the lights, and this is repeated from time to time and turning the machine on / off again does nothing. In this case it may:
break the on / off button of the washing machine;
break the control unit;
break the network wire.
It is best if the Beko washing machine with a display does not just freeze, but gives a system error with a certain code. The manufacturer has provided error codes so that the user can identify the breakdown without contacting a specialist. The description and interpretation of these codes are presented in the table below.
In theory, all Beko automatic washing machines are repairable, no matter how many kg their drums are loaded, how old they are or whether their control panels have displays. But in practice, problems often arise, or it is impossible to do the repair yourself, or it is not advisable due to the high cost, or there are no suitable spare parts available. In any case, if you find a breakdown and undertake an independent repair, you need to take these factors into account so as not to end up in the loser, losing time and money.
Important! For example, replacing the bearings of a washing machine sometimes takes hours from a specialist, calculate how long you can handle, if at all you can do the replacement correctly.
Experts strongly recommend taking on only the simplest repairs, which, for example, are associated with either the replacement of units or the elimination of blockages. It is better to leave the rest to the masters, because there is a risk of spoiling something, and this again will result in extra costs. So, which of the typical breakdowns can be fixed with your own hands?
Clean the drain filter, removing debris and dirt from there that interfere with the normal operation of the machine.
Replace the drain pump, but only if you are convinced that the old one is out of order.
Check and replace intake valve. To do this, you will also have to make sure that the problem is not in the control board.
Replace the heating element.
Ten breaks down on Beko washing machines quite often, especially for some reason on domestic models with a load of 6 kg. It is not difficult to replace it yourself, the main thing is to perform the following actions in accordance with the recommendations of specialists.
The heater in Veko washing machines is located at the back of the tank, which means the first thing we do is remove the back wall by unscrewing a few bolts.
Having removed the wall, we see a large round wheel - this is a pulley, a little lower from the tank two large contacts stick out - this is a heating element.
We take a suitable key and unscrew the fastener holding the heater, disconnect the wires from the contacts.
Gently, but with effort, pull the heating element out of the groove.
We purchase the same heating element and continue to work.
Carefully insert the new heating element into the groove and fasten it.
We connect the wires to the contacts, put the back wall of the machine in place and check the operation of the new element.
Summing up, we note that Beko washing machines, in general, are fairly reliable, however, they, like other appliances, break down. Inviting a specialist is an expensive business, so this should be done only if the breakdown is complex, in all the rest you can try to save money by doing the repair yourself.
VIDEO
A washing machine, like any other household appliance, likes to break down at the most inopportune moment.
But do not panic right away: if your unit is manufactured under the Veko brand, you can easily fix some malfunctions yourself.
And our article will help you, in which we will discuss the repair of the Veko automatic washing machine with our own hands.
To better understand which malfunctions the Beko washing machine is most prone to, you should take a closer look at the failure statistics collected by service center employees. According to their observations, the following breakdowns most often occur in these units:
Accumulation of dirt in the drain line or failure of the drain pump - 30% of cases.
Malfunctions in the operation of the electronic module - 20% of failures. The statistics are spoiled by inexpensive machines of this brand, in which the Invensys board is installed. The low-quality material from which it is made is brittle and can crack, causing the tracks to break. Most often, the semistors for controlling the heating element, filler valves, and an electric motor suffer.
The temperature sensor or heating element fails in 15% of cases.
Leaks - in 10% of cases.
Depreciation of the brushes of the electric motor or rupture of the drive belt - 10%.
The appearance of extraneous noise during operation - 10%.
This phenomenon is most often caused by a foreign object getting inside, a shock absorber breakage, or a bearing failure.
Let's look at the repair of the mechanical component of Zanussi washing machines here.
Do you own an Indesit washing machine? Then the following article will be useful for you: https://my.housecope.com/wp-content/uploads/ext/740/cancliz/mnogokvartirnyie-doma/santehnika/stiralnaya-mashina-indezit-neispravnosti-remont-svoimi-rukami. html. Algorithm for troubleshooting the unit and how to eliminate them.
In many cases, the user can revive the washing machine on their own, without even having special skills. Let's consider several situations:
To prevent dirt from accumulating in the pump, a drain filter is installed in its path - it is he who clogs most often.
Deal with this problem as follows:
First you need to find a drain filter, which is always located at the bottom of the machine behind a decorative hatch or panel.
Now you need to substitute a sufficiently capacious container under the car, into which we will drain the waste water.
Some models of Veko brand washing machines have an emergency water discharge hose next to the drain filter. If there is one, they should be used - it is more convenient to drain the water than through the filter hole.
The filter should be removed by twisting counterclockwise, cleaned thoroughly and rinsed under running water.
Using a screwdriver, you can also clean the nozzle into which the filter was installed - usually it is also heavily clogged with dirt and silt.
Since I had to take up the tools, at the same time, for the purpose of prevention, it is possible to clean the filter on the water supply, which can be easily found at the place where the inlet hose is attached to the machine body. Particles of sand and rust accumulating in it over time can prevent the collection of water.
After cleaning the drain filter, do not rush to install it in place, first you need to check the performance of the drain pump.In fact, the Veko washing machine, thanks to the built-in self-diagnosis function, in many cases can itself track the malfunction of the pump, while displaying the error code “H5” on the display.
But there are breakdowns that the machine “does not see”, for example, wedging of a loose impeller (you can guess the appearance of a strong backlash from the characteristic hum).
To check the pump, you need to start the machine in drain mode, watching the impeller through the filter plug hole. It must rotate. If this does not happen, the pump must be cleaned or replaced.
This plaque (scale) retains heat like a fur coat, so the heating element overheats and burns out.
In the absence of scale, it can also burn out - from the exhaustion of a resource, just like an ordinary incandescent lamp burns out. The machine can signal problems with the heater with the codes “H2” (heater break) and “H3” (heater constantly on).
To accurately determine the state of the heating element, you first need to get to it. In some models of Veko machines, for this you need to remove the back panel, in others - the front.
To remove the front panel, you have to dismantle the sealing collar of the loading hatch. It must be removed very carefully - the slightest damage will lead to leaks.
The heater is detected by two contacts at the bottom of the tank with wires connected to them. Disconnect the wires and use a multimeter to measure the resistance between the heater contacts. Normally, at room temperature, it should be 25 - 35 ohms.
Other indications (usually “infinity”) indicate a malfunction: the heating element must be pulled out by unscrewing the nut holding it (between the contacts) and replaced with a new one, carefully descaled the mounting hole from the inside.
It happens that, contrary to expectations, the heating element turns out to be serviceable. Then you need to check the performance of the temperature sensor, which is located under the top cover (to remove it after unscrewing the screws, you need to move back a little). At room temperature, its resistance should be approximately 4.7 kOhm, and after heating with hot water, it will decrease significantly.
If the thermostat is defective, it must be replaced. For dismantling, it is necessary to pull out and disconnect the powder dosing bin, then remove the control panel, having previously disconnected the thermostat and command device handles from it.
Firstly, the machine is much easier to disassemble than many others, and secondly, it is most often not required to completely remove the tank.
Only the front part of the tank is removed, after which it becomes possible to pull the drum out of the rear part, which remains in the car.
The exceptions are cases when one of the bearings is completely destroyed and its parts have to be removed from the glass.
To gain access to the front of the tank, you must first remove the front panel of the machine and unscrew the lower counterweight. Now you need to disconnect all tubes and wires connected to it from the tank.
Before disconnecting the tank from the wires and pipes, take a picture of it with a camera with sufficient resolution, especially the wires. By looking at the photos, it will be possible to avoid assembly errors.
The front of the tank is fixed with 12 clips that must be removed. After that, it can be disconnected and pulled out. It remains to unscrew the back wall of the housing, remove the pulley from the drum axle shaft and pull out the drum itself. The bearings on the axle shaft are fitted with an interference fit, so it has to be knocked out with careful blows of a rubberized hammer.
It is forbidden to reuse the screw that held the pulley on the drum shaft.
You can find the recommendations of Ardo washing machine repair professionals at this link.
VIDEO
Attention! Today, there is a special offer to replace the drain pump in this washing machine, details at the link - discount for replacing the drain pump.
departure of the master to the house throughout Moscow - free of charge
fault diagnostics - free of charge (in case of refusal to repair - 600 rubles)
Warranty for work performed up to 36 months. BO-1
details by phone: +7 (499) 495-10-97 (24/7)
V. How quickly will the technician arrive and fix the problem? O. It all depends on the timing of the application. As a rule, if the client calls before 18:00, the master arrives on the same day and performs all the necessary work. If the application is made after 18:00, then the specialist arrives the next day, at a convenient time for you.
V. Is it true that your visit and diagnostics are free of charge? O. If the client calls the master to repair the equipment, then the diagnostics are not paid. We also have a separate service “diagnostics without repair” - it includes a complete diagnosis of the washing machine, troubleshooting and issuing BO-1 regulatory documents. The cost of such a service is 600 rubles.
V. A friend said that there are Chinese spare parts, and they are cheaper. It's true? O. Now is the 21st century, and there are not only Chinese spare parts, but also Russian-made spare parts. But we use only original spare parts, purchasing them directly from manufacturers, according to existing contracts. Thus, our prices for spare parts are sometimes lower than for “China”, and the quality is many times better.
V. Does your service center issue a warranty for repairs? O. Yes. We undertake to fulfill warranty obligations in accordance with the Federal Law “On Protection of Consumer Rights”. The warranty period ranges from 6 months to 3 years. Find out details by phone.
What can we offer you? - First of all, quality Repair of washing machines at an affordable price.
Secondly, useful tips that will help you avoid problems with the washing machine in the future. The best masters of the city of Moscow work in our company.
The experience of employees and their attitude towards customers is the symbol of our company.
We value our customers and do our work with honor and dignity.
If you decide to repair washing machines yourself, there are many nuances that must be taken into account. To avoid the consequences of improper repairs, such as when removing a blockage, you need to know which side to put the washing machine on in order to avoid a short circuit. Therefore, we recommend that you ask a question in the "Questions - Answers" section or get a free consultation from our operator at +7 (495) 762-22-90 .
Repair of beko washing machines - main faults, detailed prices, as well as useful tips.
1.5 -2 Atm. The drain pump is already growling, I will change it. The command device is intact, the contacts are normal, the power supply of the 5.2v processor is set by the zener diode, the buttons are working. The wiring is outwardly intact, nothing is mixed up, nothing is burnt.
1.5 -2 Atm. The drain pump is already growling, I will change it. The command device is intact, the contacts are normal, the power supply of the 5.2v processor is set by the zener diode, the buttons are working. The wiring is outwardly intact, nothing is mixed up, nothing is burnt.
Perhaps there is debris in the valve, or its spring has weakened, or the water pressure in the system “floats”.
Water pressure 1.5-2 Atm, at a rate for a machine 1-10 Atm. At 10 of it, it will pour over the top! Or does she have a mind?
I'm embarrassed that the water is gaining under the emergency level! When the drum rotates, the drain pump kicks in. The hostess complains that the program goes astray. I managed to knock down the program if at that time I pinched the pressure switch tube and pressed it down a little more. It turns out - emergency protection? Or did I mess up something?
To replace the bearing in the Beko washing machine, you need to disassemble its body. The machine is disassembled from the front. First, disconnect the lower decorative panel and separate the seal of the hatch and the lock of its door. The design of Beko machines, unlike many other models, allows in some cases to do without completely removing the tank from the body. Yes, and the disassembly of the case itself is much easier.Unless major repairs are required and the removal of parts of the scattered bearings, the drum can be removed from the back of the tank, leaving it in place and removing only its front cover. This simplifies the work of the master and reduces repair time.
To disassemble the tank, the front panel and the lower counterweight of the tank are removed. Next, remove the tubes and wires suitable for the front of the tank, as well as 12 clamps with which the front cover of the tank is attached to its main part, and remove it. Then, having removed the back cover of the machine body, disconnect the belt and pulley and remove the drum. The bearing unit is pressed into the tank and consists of two bearings of different diameters located in a common glass. Put new bearings and assemble the machine. Finally, the build quality is checked.
In particularly difficult cases, the main (rear) part of the tank has to be removed entirely so that it can be worked on separately (knock out stuck bearings, for example). To do this, you need to disassemble the machine much more completely - remove the top cover of the case, the detergent dispenser, the control panel, disconnect the remaining wires and tubes, shock absorbers and springs from the tank. Sometimes it is really necessary, then the work of the master is added.
Departure of the master at a convenient time for youAccording to the record queueRepair within 1 day in your home
Taken for repair to the workshop, they charge for deliveryOnly original spare parts
Chinese low-quality analoguesExperienced craftsmen with experience from 5 yearsinexperienced employeesFree diagnostics in case of repairDiagnostics from 1000 rubles Guarantee for repairs up to 2 yearsGuarantee no more than a month
Washing machine with horizontal loading BEKO WMN 6508K is very popular. This type of device has many advantages. But, like any equipment, during operation, the units wear out, and their components and parts require replacement. In addition, there are several serious breakdowns that can lead to the inoperability of the machine.
Self repair washing machine BEKO WMN 6508K , which is resorted to by inexperienced users, often leads to even greater breakdowns, since unskilled intervention in the design of the device is not provided by the manufacturer. To top load washing machine BEKO WMN 6508K worked for a long time and with high quality, it is recommended to use the services of a specialized service center. Only such a company has the necessary equipment and employs the necessary specialists.
Side-loading washing machines come in a variety of looks and fit well into any bathroom or kitchen. These devices, unlike top-loading modifications, consume less water.
But such a washing machine also has disadvantages. These rightly include the fragility of the drum bearing and a high level of vibration during washing and spinning. Also, in the event of a power outage, it is impossible to get laundry out of such a unit, avoiding pouring water onto the floor.
However, according to experts, the repair of a machine with horizontal loading BEKO WMN 6508K easier and less time consuming than repairing "vertical" varieties. But it should be produced only with the use of special equipment and people who have received appropriate training.
Most often washing machine users BEKO WMN 6508K Sideloaders face the following issues:
the machine does not drain the water - this malfunction is the result of a clogged filter or a breakdown in the drain pump control;
the machine does not wring out the laundry - the problem lies in the malfunction of the tacho sensor or the electronic module;
the machine does not draw water - the valve filter is clogged, the electronic module or pump is broken.
In case of any breakdowns, it is recommended to contact the service center, where experienced specialists will carry out high-quality diagnostics and correctly repair the washing machine with horizontal loading BEKO WMN 6508K .
About the malfunction of the drain device of the washing machine BEKO WMN 6508K indicate the following signs:
the program stops working right before the start of the drain;
water does not drain at all stages of washing;
water does not drain only after rinsing;
draining the pod is too slow, and after it ends, the program crashes;
water is drained normally, but subsequent spinning is blocked by the program.
The most common cause of these problems is a clogged drain pump filter, drain hose or fitting that is located between the drain pump and the drum tank. In addition, the problem sometimes lies in the clogging of the sewer siphon or the ingress of foreign objects directly into the sewer.
Even if you are familiar with the design of a top-loading washing machine, it is not recommended to disassemble it yourself and try to fix the breakdown. It is better to entrust the repair of equipment to experienced professionals who will carry out diagnostics and reliable repairs in the shortest possible time.
To eliminate the blockage, the master opens the machine, dismantles the drain pump and the electronic unit - these elements are checked separately. It is hardly possible to do this work on your own. This threatens with additional damage.
If the drum of the washing machine with horizontal loading BEKO WMN 6508K stopped rotating, this may indicate several types of breakdowns.
First of all, we are talking about mechanical damage caused by the ingress of a foreign object into the space between the drum and the walls of the machine. In second place are malfunctions of electrical circuits or an electronic module.
Often the reasons for stopping the drum are the wear of the drive belt, which burns out and needs to be replaced, the wear of the brushes that wear out from long-term operation, the engine breaks or the heating element burns out. All of these cases need to be addressed. Repair of a washing machine with horizontal loading, which should be carried out by a highly qualified craftsman at a special stand.
Before repair, it is necessary to conduct a thorough diagnosis of all components of the device. During operation, additional malfunctions may be detected that need timely elimination.
Absolutely silent mechanical devices do not exist, this is just an advertising ploy by manufacturers. But there is an acceptable noise level, which is 50-70 decibels. If, during operation, the top-loading washing machine BEKO WMN 6508K makes very loud sounds, squeaks, knocks and vibrates excessively, it is worth diagnosing and finding out the reasons.
Too noisy washing machine BEKO WMN 6508K may be for the following reasons:
small objects getting into the space between the drum and the walls. Sometimes this can lead to jamming of the drum and its complete breakdown, so the foreign object must be removed;
drive belt wear. In the process of long-term operation, the belt becomes thinner, and its untimely replacement leads to combustion. This may affect the performance of the drum;
friction of the tank against the walls of the washing machine body. This situation occurs when the fasteners are loosened or the shock absorbers are worn out. If the damaged parts are not replaced, the horizontal loading washing machine will fall apart from the inside;
wear of the backlash of the drum shaft, which must be eliminated;
loosening of fasteners between the elements of the machine body. Loose brackets must be screwed or replaced with new ones;
bearing failures. Untimely replacement of a damaged part leads to the destruction of the rotation unit. If it comes to this, the subsequent repair of the washing machine BEKO WMN 6508K will cost significantly more.
Bearing wear is a common failure among machines that have served more than five years. It is not recommended to replace it yourself, since for work it is necessary to partially, and sometimes completely disassemble the washing machine.Incorrectly installed parts are the causes of new, more serious breakdowns.
Video (click to play).
Whatever the repair of a horizontal loading washing machine BEKO WMN 6508K , after the repair, the master conducts the final diagnostics of the equipment, which helps to prevent the occurrence of leaks, squeaks and other malfunctions. And home repairs can end with a uniform flood, the consequences of which are obvious to everyone.
