Striking wall clock amber DIY repair

In detail: wall clock amber DIY repair from a real master for the site my.housecope.com.

The factory producing most of the large-sized watches in the USSR was the Oryol Watch Factory. On many watches on the dial was the abbreviated name of this plant "OCHZ". The factory began to produce watches Amber in the late 60s. The watch became very popular among the citizens of the Soviet Union. Nowadays, they still use this watch, this speaks of the good quality of the mechanism, because with proper operation and timely prevention, the Amber watch with a pendulum can last at least 100 years. A watch was brought to the Fullfix watch center for repair after a long stay in the attic. Corrosion has strongly eaten the chrome-plated elements of the case, we will carry out restoration and repair of watches. Let's start with the watch case.

As you can see, there are traces of paint on the body, most likely due to storage in the attic, corrosion has appeared on the chrome parts.

The condition of the case and chrome-plated parts leaves much to be desired, there is also corrosion on the dial elements.

The pendulum is covered with a layer of rust.

We will remove rust from the case and dial elements by polishing with abrasive wheels.

Let's pay attention to the striking strings of our clocks, as we can see the time also did not pass them by, we will carry out the restoration of the "voice", our clocks.

From the exterior of the watch, let's move on to the internal mechanism. Dust has adhered to the old watch oil and an unpleasant "mess" has formed, we will disassemble and clean everything.

In the process of parsing, we notice the absence of a pawl spring on the mechanism. Repairing antique pendulum clocks is not an easy task these days, you have to make some spare parts yourself, as new ones can no longer be found. We make the spring ourselves and solder the missing end to the old piece in platinum.

Video (click to play).

We disassemble the watch and wash everything in a special solution.

We assemble and lubricate the mechanism.

We insert the mechanism with the dial into the watch.

After restoration, the watch took its original appearance, the watchmaker №1 in Sokolniki Fullfix coped with its work perfectly.

The striking wall pendulum clock is a household clock. In terms of accuracy, they satisfy the need for measuring time in everyday life. The watch has a device for striking a clock and half an hour.

After unpacking the watch, free the pendulum from the holders. It is not recommended to take the pendulum by the load with unprotected hands, in order to avoid corrosion and oxidation of it.
Hang the clock on a wall away from windows and heating systems.
Remove the shipping bar from the sound strings.
Move the fight fence lever (if there is one).

5. Carefully place the pendulum on the hanger with the hanging hook.

6. Set the watch so that the pendulum rod is parallel to the back wall of the case. Parallelism can be achieved by rotating the set screws on the bottom of the case.

7. To wind the chime, insert the key into the left hole on the dial, winding is done clockwise. Move the key to the right hole and insert the travel spring as far as it will go. The watch must be wound every two weeks. For two weeks of operation of the watch, the power spring unwinds by 6 full revolutions, the striking spring unwinds by 5.65 revolutions. ! When winding the watch, be careful not to knock the case to the side.

8. To start the clock, take the pendulum to the side and release it smoothly, the movement should be rhythmic. If this is not observed, carefully move the lower part of the watch case to the right or left, achieve rhythmic strokes of the movement. ! If you cannot achieve the rhythm of the movement by moving the watch case, you should contact the watchmaker.

9.Set the exact time by turning the minute hand. If the hands diverge, set the minute hand to the “12” position, and adjust the hour hand by turning it to the left or right. ! When rotating the minute hand, it is advisable to stop it at the “6” and “12” positions, and enable the clock to strike the hours and half hours.

Adjusting the accuracy of the wall, grandfather clock

If the clock is inaccurate, it is adjusted by moving the weight of the pendulum. If the watch lags behind, the weight must be lifted up by turning the adjusting screw clockwise, if the watch is in a hurry, lower the weight in the same way, counterclockwise. One full turn of the adjusting screw corresponds to a change in stroke of one minute per day.

In order to prevent damage to the watch, when adjusting the stroke, the pendulum must be removed from the suspension.

A dry, heated room is required to store or use wall clocks, floor clocks. It is not allowed to store watches in the same room with substances or materials causing their corrosion.
A watch with a suspended pendulum must never be carried.
The watch mechanism is lubricated with special watch oil brands MC-3 and PS-4. The service life of the oil is 3 years, during which time it is recommended to clean and lubricate the mechanism. Replacing the oil of the indicated brands with others is not permissible.

To avoid voiding the warranty, it is not recommended to lubricate, disassemble or repair the watch yourself.

AMBER watch with striking. main causes of breakdown. and elimination.

Repair of striking watches, shown on the example of watches Yantar, Oryol Watch Factory (OCHZ).

the next clock came for repair.

How to fix an old wall clock Amber clock 1965. Oryol Watch Factory (OCHZ Yantar). Orlovsky.

Repair of striking watches, shown on the example of watches Yantar, Oryol Watch Factory (OCHZ).

The wall clock "Yantar" came to me for repair. I had to dig around the boy, testing the mechanism in operation.

HOW TO REPAIR AN OLD PENDULUM CLOCK.

Clock mechanism OCHZ 1957 with a fight. After service. Combat levers stand from late Amber. The fight is not set up.

Striking watch repair. Striking of the clock with the OCHZ pendulum Wall clock with the striking OCHZ (Oryol Watch Factory) for a duration.

To adjust the clock, I used the Android program "Clock Tuner". A very useful program for configuring how.

For many years now, we have had a wall clock with a Soviet-made pendulum hanging in our houses. Hanging, but not walking. After winding the springs and starting the pendulum, they stop and do not move, so I decided to fix them. It took me a lot of time, I will try to briefly tell you about it.

On the advice of dear members of the forum, I took off the dial and hands, unscrewed the anchor and set the mechanism to soak in Kalosha gasoline. After that, they had to go, but still something interfered with the move.

Why can't a person find the videos they want on Youtube? The thing is that a person cannot come up with something new and look for it. He was out of fantasy. He has already watched a lot of various channels, and he no longer wants to watch anything (from what he watched earlier), but what to do in this situation?
In order to find a Youtube video that suits your needs, it is imperative to keep searching. The harder your search is, the better your search result will be.
Remember that you only need to find a few channels (interesting), and you can watch them for a whole week or even a month. Therefore, in the absence of imagination and unwillingness to search, you can ask your friends and acquaintances what they are looking at on Youtube. Perhaps they will suggest original vloggers that they like. You, too, may like them, and you will become their subscriber!

Online mp3 cutting is convenient
and a simple service to help you
create a musical ringtone yourself.

YouTube video converter Our online video
the converter allows you to download videos from
YouTube website in webm, mp4, 3gpp, flv, mp3 formats.

These are radio stations to choose from by country, style
and quality. Radio stations all over the world
over 1000 popular radio stations.

Live broadcast from webcams is made
absolutely free in real
time - broadcast online.

Our Online Television is more than 300 popular
TV channels to choose from, by country
and genres. Broadcasting of TV channels is free.

A great opportunity to start a new relationship
with a continuation in real life. Random video
chat (chat roulette), the audience is people from all over the world.

How to fix an old wall clock

Watch Amber 1965. Oryol Watch Factory (OCHZ Yantar).

Oryol Watch Factory "Yantar" - a plant in the USSR, produced large-size floor, wall and table mechanical and quartz clocks. The Oryol Watch Factory also produced alarm clocks.

The first batch of products was released in 1952.

In the 2000s, the plant had financial problems and soon ceased to exist.

How to fix an old wall clock
Watch Amber 1965. Oryol Watch Factory (OCHZ Yantar).
The Oryol Watch Factory "Yantar" is a plant in the USSR, which produced large-size floor, wall and table mechanical and quartz clocks. The Oryol Watch Factory also produced alarm clocks.
The first batch of products was released in 1952.In the 2000s, the plant had financial problems and soon ceased to exist.
Watch my videos by topic:
Unboxing: /> Reviews: /> Review of LED lamps: /> Review of food: /> Recipes for a multicooker: /> Other recipes: /> Repair: /> Little tricks: /> Crimea: /> Quail: /> Moonshine: /> CHDK: /> Military Search Expedition: />
You can connect to the affiliate program and make money on YouTube by following this link:AMBER watch with striking. the main causes of the breakdown. and eliminationA person constantly monitors time, not even paying attention to it. He casts a fleeting glance from the car window at the street display, at the dial of a wristwatch, keeps track of the progress of time on TV, computer, telephone. Now you will not meet a passer-by on the street asking: "What time is it?"However, there is something touching in the old chiming clock of the last century, which makes you stop for a moment and count the number of strokes, and then look at the dial, checking yourself to see if it is going.The striking clock of the Yantar plant can sometimes be found in the apartments of people who have managed to preserve the relic. It is possible that the fight will interfere with the household at night and it is better to hang such a clock in the living room, but it is important to properly care for them so that the clock will last a long time and be inherited by the future generation. In order for the clock to run correctly and not to interrupt its movement, it should be hung on the inner wall, which has no door and is not subject to vibration. The striking watch should be fastened exactly without distortion, in this case the strikes will be uniform.The watch, which is almost half a century old, has definitely fallen into the hands of a watchmaker more than once. They remember the touch of the caring hands of an experienced craftsman who loves his work, and the rude inept attempts to fix them by a self-taught person who knows little about the mechanism of watches.Now you can safely entrust the Yantar watch with a break to the service center, which employs professionals. Specialists will test the watch, repair it, replace the damaged parts of the mechanism with new ones and provide them with warranty service. After visiting a trusted company, the watch will work like new and delight its owners.

The pendulum mechanism is durable and unpretentious, with proper care it can work for a long time, but it needs cleaning every two to three years. The dirt that has accumulated in the watch parts for several years affects the operation of the mechanism, the movement is thrown off, the hammers, briskly beating their song every hour, sound more muffled, which means it's time for cleaning.In the service center “Tochnoe Vremya”, the watch “Yantar” will be repaired and cleaned by masters using the latest technologies and tools used for watches of elite brands. The final touch for each master is checking the progress and accuracy, special attention is paid to the striking wall clock, due to its design features. After the workshop, you need to fix the watch on the surface in such a way that there are no distortions and the efforts of the masters are not in vain.Electromechanical wall clock Amber comes from the 80s. In this case, this is the simplest option without a fight in a simple (although with a claim to design) plastic case.The frequency setting element of the mechanism is a spring pendulum, and a generator with a pair of coils is engaged in swinging. This determines not the highest accuracy. Powered by one element 373 (aka type D).Unfortunately, after 30+ years, the mechanisms of watches of this type and age are usually in a deplorable state - the accuracy of the watches is poor, the battery runs out quickly, they can just get up. This is due to the lack of maintenance and trivial wear and tear. Of course, you can slightly refresh the mechanism, but usually the parts require not only lubrication, but also cleaning, which is not suitable for everyone at home. Just pouring watch oil in different places usually does not save for a long time, if at all changes something. In addition, the abundance of Soviet plastic from the 80s in the mechanism raises some doubts about the outcome of this enterprise.The radical remedy is replacing the mechanism. Modern movements are much more compact and are usually quartz-stabilized and powered by a single AA cell. Importantly, the replacement mechanism is usually virtually silent! True, now the mechanism will be almost completely plastic and not authentic Soviet, but Chinese.First of all, it is necessary to dismantle the old mechanism - this must be done carefully. The dial with the old movement must be unscrewed from the outer case and removed from it, the hands are simply tightly mounted on the shafts - they must be removed. The mechanism is attracted to the dial by a brass nut - it is located on the front side under the hands. This nut does not always give in - if so, it is better to wield from the side of the mechanism (unless, of course, it is dear to you as a memory) - you can use a drill and cutting wheels. The new mechanism has a similar fastening, but its length is shorter, so the elastic band under the mechanism most likely will not work - I suggest damping the strips of electrical tape with a sticker.The mechanism should not turn, but do not get carried away especially with a tightening. We also lose our native fasteners on the wall (in the version where the fasteners are directly above the mechanism) - there are replacement mechanisms with a loop, but I don't really like this option - and the clock is not a fluff, and it is not known whether that loop will be enough for your nail in the wall. As an option, I propose to fix a wire between the screws for attaching to the outer casing and make a suspension from it.There is a positive point - most likely it will be possible to preserve the native hands - for the minute and hour landings they coincide. Our second shaft is thinner, but if desired, the bore hole can be unclenched - it will hold. However, you can try to find a mechanism with similar openwork arrows, although their length will have to be clarified.An important point in setting the hands is to synchronize them correctly, that is, when the minute looks at 30 minutes, the hour should show half of any hour.

Science and technology

AMBER watch with striking. the main causes of the breakdown. and elimination

Hello! Thanks for the information! I can’t sleep when they do not beat!

How many times to start? Or all the way, I can't understand. And how to equalize the time with the number of fights, that is, on the arrows, for example, 6 o'clock and it hits once?

He didn’t really say anything, and even more so he didn’t show who is interested in sleeping under the chime of the clock, create an appropriate topic. How to clean? how to lubricate? what are the reasons for the breakdown? how to fix? not to mention the fact that the camera is directed somewhere into space. If a bad camera and poor lighting, why shoot and upload videos? Waste the time of those who are really looking for material on the topic. Nothing but annoyance, this video did not give

this is not called a fork, but a bracket

Thanks for the video, it helped a lot, I cleaned the watch and it began to walk, and the master told me not to clean

I have a watch. Amber has been banged for repairs, the clock runs, but from 10 to 11 they go and stop during this period

And how old are you? And where do you live?

And how loud do they beat at all? How is it perceived? Aurally?

Do you sleep in the same room as the clock or not?

Hirakura Towegabe I'm sleeping .. I can't hear them. only in the morning when to get up .. human physiology is an amazing thing.

At the dacha, the cuckoo clock is a beacon and they go and then they just melt

compozitorify thanks for the answer I will ask dad to clean

Kirill kraft is likely to be corrupted

Hello! The clock is running, but the bottom of the case needs to be taken a little to the side by 3-4 cm, i.e. not vertically how to rehearse?

You yourself thought what you wrote?

Konstantin Savateev easy! The mechanism itself is mounted in a wooden case - a box! Rotate it to the desired degree, so that the box itself hangs straight! In my opinion, the child would have guessed!

It is necessary to wait for the end of the battle in a quarter clock and a three-spring clock with a melody. Otherwise, the frequency of the quarter battle and the beating of the clock is lost.

good advice, went to clean and adjust.

Greetings.
Wall clock "Yantar". When the mechanism itself with the pendulum is on the table, the clock runs without problems. But if you return the mechanism to the case, the pendulum starts to wedge, and the clock stops. What is the reason?

If the wall is not flat enough in the plane and is "overwhelmed" vertically - by adjusting screws and moving the case to the left-right, you can achieve the position of the clock mechanism, which is on the table (taking into account that there is no development of the movement mechanism).

I will sell watches amber 87756121302

can you do without gasoline? eg air or brake spray?

On the good, it is necessary to completely disassemble the mechanism. Remove old grease with dirt (including in the bores for the trunnion). Then lubricate with the types of greases recommended for these units. And only after that, collect and configure the course and mechanism of the battle.

we have one repairman in the Crimea, he sits in a simfer in the central general store, where he takes 2500 hours for any repair of such a clock and does prevention for 2500 well, cool in general, but it does the perfect truth.

They are 7 minutes late a day tell me how to fix the clock like yours

you say you shoot for people. camera in one direction - a conversation in the other. 90 percent of people in the end did not understand fucking, I am sure.

By the way, it was this brand of watches that I remembered from childhood when I saw it on the wall of neighbors. They hooked me with their charisma and design. I don’t know what, but I liked them and I would buy them with pleasure. Thanks for the video.

Thank you very much for this video, tell me, are there any differences in the structure of the watch mechanism of this brand, produced in the 50-60s and later, in the 70s, for example?

The length of the pendulum axis may differ on different mechanisms (with a fight, without a fight).

Hello. OCHZ. Quarter hours. A broken tooth on the melody drum. Do you happen to have it? Teeth diameter 63 mm, drum diameter 58 mm, number of teeth 80.

Understood thanks. I will look for. or have to sharpen. thanks again.
maybe call my father, if he has one, then I'll buy and pay for the postage.
Thanks again for your participation.

Leonid Zaichik, look for even a bad drum, you can cut out these teeth from it and replace it with a dovetail, followed by soldering ..

Hello Leonid Zaichik. Unfortunately, I don’t have spare parts. Yana has a watchmaker at her father. Maybe he does, but he lives far away.

I have the same watch. Where to find the year of issue.

hello! why are there two pins inside the clock ?? on the right and left inside! on the case!

Why mounts at the bottom of a wooden case?

You mean 2 adjusting bolts at the bottom of the case. if yes then to adjust the angle from the wall ..

The question is, the clock slows down the battle, does not turn quickly during the battle, but with the brakes, it barely turns.

aerosol can for cleaning carburetors. pop a shit on the whole mechanism. dry by the battery. lubricate all axles and gears. all. collect and enjoy work

Most likely, all the cleaning will help. and look at the tools.

Hi, thanks for the video. But there is an inaccuracy, lifting the bridge plate regulates the pumping out of the pendulum in amplitude, respectively, after it is necessary to adjust the accuracy of the clock. But the one-sidedness of the movement is exposed by turning the anchor plug into the already installed watch case.

All right, you can hear it on the snaps

Can I clean it with white spirit instead of gasoline?
Your comment language is interesting. A kind of Albany? ))

and if isopropyl or some other alcohol? and will clean it and there will be no stinks, or is it necessary to clean it with some fatty oil product?

this watch can even be a solarium just if you do it in the apartment it will stink better with ordinary gasoline!

Poured with the same problem the other day I took it from Father - I wanted to throw it away. I sit down to fix it.

Model 118151 79 I have

Yes, you can't see the darkness, if you shoot, do it according to your mind

I shoot with what there is a camera .. I do not flock on advertising. I rent for people and not for profit, so sorry

It would be nice to first of all comment on how the mechanism was removed.
This important detail is generally shown in passing, and is not explained clearly.
Thank you.

Regarding sleep, I also don't see a problem at all (I also have a child). Gustav Becker's grandmothers and grandfathers have recently restored - the mechanism is basically the same. Also with the fight. They hung it up. On the first night, everyone slept well. After a week of use, they had no idea how they used to do without them). Their fight promotes self-organization). You don't lose control over time. You understand that you have the Thing.
Many thanks to the author - very useful!

yes, there is such a feeling when they stop, then some kind of anxiety as you envy and neglect everything super mechanism acts as a soothing they say on digestion it works well, say the doctors

Last time I visited a watchmaker in 2004, they stopped again, I want to try to clean it myself, I need to completely disassemble the mechanism (then you won't understand how it was + springs) or put it in a vice and where did it get in there and wipe it?

compozitorify, Hello, I got the same clock and also practically without a pendulum .. it is but homemade ..) and I'm not sure about its weight and size .. If it's not difficult to share the size and weight of the pendulum. Thanks in advance!

if you are going to sound them, I can throw off the size of the maitnik.

I found the same clock at my grandmother's, lying about 18 years old, started it up lying without a pendulum ticking, you put a minute to go and get up, dust and dirt are not visible.

Read also: Do-it-yourself grundfos pump

dai .. and trying to push the fork further away from the escape wheel. experiment .. look at the sample on the fork eats. if yes, remove it with a diamond file and slap it, I'm talking about the heels of the contacts on the fork with an anchor wheel

The counter with gear 2 of the Roshkovo Katoraya lets you know when to hit. she, as a hropovik, will not give a minute and go back if it is forcibly then a breakdown

There are do-it-yourself amber clock with striking wall repair, with minute and second hands. The mechanism of such accessories is mechanical and is manually adjusted. Sometimes only the minute hand is present, or both are absent, and the points on the dial, replacing each other, serve as a reference point for the time. Another type of wristwatch is called electronic. The time is calculated by an electronic mechanism with a battery, and the information is transmitted by an electronic dial.

Also, Astrakhan gold watches are ordinary and self-winding. The first ones need to be wound up every day so that they show the correct time. If the device is equipped with an automatic winding mechanism, this is not necessary, the watch will not stop at the most inopportune moment, but will work perfectly without stopping. Almost all modern watches are self-winding, people are more willing to buy such a product.

Electromechanical, or as they are also called, the most precious thing for a person is the life of the class hour, and are also very popular with buyers. They work thanks to a small battery, and instead of a pendulum, a quartz crystal. The hands of such watches, as a rule, are absent, and their electronic-digital dial replaces them. They do not need a factory and work until the battery runs out. This is a very common type of watch.

Our site will help you quickly find an experienced craftsman to order any home appliance repair services. Submit your request and trusted specialists will offer you their services and prices.

The Soviet-made amber wall clock was popular in the last century. And today, someone has them as a dead weight in the attic, someone admires the mechanism in the village with their grandmother, and lovers of antiquity and collectors buy from the owners and give them for repairs with a strike and without it. And looking for masters

competent, responsible and experienced;
neat and executive;
able to appreciate the old model.

Because the repair of wall clocks Amber requires not only professional skills, but also mental attitude and utmost diligence. Because it is difficult to restore broken parts of the mechanism, and it is completely impossible to find a replacement.

Well, don't despair! There is our YouDo crowdsourcing exchange on the Internet, so collectors from Moscow and St. Petersburg will easily find an excellent performer. The people we have registered are reliable and proven. And if the specialist indicated that he was repairing the Yantar watch. This means that he has both skill and dexterity. And, importantly, the master is also interested in it. Truly in love with his work, the pro, enthusiastically engaged in necessary and useful work, works accurately, but quickly and with a twinkle. To breathe new life into a mechanism that has been lying in the attic for 20 years - what could be more beautiful? Ace is capable of:

restore the broken clock;
bring the watch into working condition;
to perfect the external parameters of the mechanism.

Do you want to see an absolutely happy person? Then give just like that to the collector who collects hand, floor, wall mechanical or electronic clocks, a chic mechanism with a strike. Moreover, after the Yantar watch had been successfully repaired.

If the repair of the wall clock Amber is completed successfully, then the owner remains

place them correctly;
follow the recommendations of a specialist;
promptly call the foreman for prevention.

And then the mechanism, which has received a second birth, will always indicate the exact time, and the smooth, deep chiming of the clock will remind you of the transience of life and set it to the desired pace. And all this is possible due to the fact that there are masters in the capitals who are able to undertake the repair of Yantar watches. And you can find them here, on the stock exchange.

Video about how I installed the clock on the wall. The watch looks pretty good, I have never regretted a purchase.

Review of good wall-desk clocks. Bought here - good seller.

Cool electronic clock on the table or on the wall - Aliexpress. LINKS - and Save.

We make a wall clock with our own hands. I saw such a clock in one of the apartments and thought that it might be.

How to fix an old wall clock Amber clock 1965. Oryol Watch Factory (OCHZ Yantar). Orlovsky.

DSLR and photography from scratch: Photoshop from scratch in video format: Photoshop.

The easiest and fastest way to repair a wall clock in Prokopyevsk, the "Mix" shopping center.

Wall clock. Material elm, epoxy resin, oil.

I decided to buy a huge 3D wall clock in China, which I need to assemble and install myself. Today we are with.

50 wall clocks. Clock ideas. Some people might argue that regular wall clocks are becoming obsolete. After all.

Repair of a non-working, new, quartz, Chinese wall clock mechanism. I took it here:.

I bring to your attention a wall clock with a battle from the times of the USSR. They go well, they hit the prescribed number of times.

Original wall clock with 3D effect! Original designer wall.

I ordered this watch (10 colors) here: Sex clock: I bought a huge clock on the wall,.

The text is already better, but so far it is lame, as is the diction. Great clock for a table or wall. Purchased here:.

Musical wall clock Rhythm 4MH817WD06.

Wall clock 3D Diy clock You can order a clock here Cool and unusual Large.

Fabulously beautiful as a church battle

What is the full name of the clock that is 27 seconds (left)?

RapRetelling there all watches are amber of different modifications

Very beautiful ringing, a little like a church one

skajite. kagda snimaiu maitnik chisi rabotaiut, a kagda veshaiu maitnik chisi ni xodiat pochemu?

Krasava, only what is the point of collecting them? The mechanism is the same there, I'm talking about amber. I have 6 cuckoos, well, no longer interesting. you know the whole mechanism by heart. OCHZ has not yet disassembled to the end, only opened the drums and put the strikers. Well, cleaning. Here's the question, if the mechanisms were different, but just the case. It's a shame.

Video about how I installed the clock on the wall. The watch looks pretty good, I have never regretted a purchase.

Video blog about design, architecture and style. Ideas for those who equip their house, apartment, cottage, garden.

Wall clock Energy EC 02 ——————————————————– Wall clock Energy EC-02 will decorate the interior of any room.

On sale from 02.02.2018 on the website / p>

Modular wall clock "Couple in love", 80 × 140 cm product link.

link to watch

A very beautiful and inexpensive entourage thing. The starting price is only 1000 rubles! Place your bets, gentlemen! Send.

Top 10 of the most striking, original and insanely stylish wall clocks from the global online store Aliexpress.

Wood, carving, toning, painting; m / c, casting, mount; glass. Dimensions: 51x20x15 cm. This type of wall.

How to fix an old wall clock Amber clock 1965. Oryol Watch Factory (OCHZ Yantar). Orlovsky.

Wall clock 3D Diy clock You can order a clock here Cool and unusual Large wall clock.

Wall clock ОЧЗ with quarter strike 1962

We make a wall clock with our own hands.I saw such a clock in one of the apartments and thought that it might be.

Video blog about design, architecture and style. Ideas for those who equip their house, apartment, cottage, garden.

Video about how I installed the clock on the wall. The watch looks pretty good, I have never regretted a purchase.

link to watch

Domino wall clock DIY clock **************** Do not forget to subscribe, click on the bell next to.

Top 10 of the most striking, original and insanely stylish wall clocks from the global online store Aliexpress.

We make a wall clock with our own hands. I saw such a clock in one of the apartments and thought that it might be.

One of the main elements of the decor is the clock, and when the clock is wall, and even the size of their meter, and made.

I wanted to somehow properly attach a few planks of my tiger tree so that there was a striped pattern.

Bought here:

1906 YEAR. le Roi a Paris Antique wall clock with striking. The case is wooden with glass, a fight every half an hour. Dial.

50 wall clocks. Clock ideas. Some people might argue that regular wall clocks are becoming obsolete. After all.

Repair of a non-working, new, quartz, Chinese wall clock mechanism. I took it here:

How to fix an old wall clock Amber clock 1965. Oryol Watch Factory (OCHZ Yantar). Orlovsky.

Soviet wall clock "Yantar" with a fight, Oryol watch factory, 1969.

I filled the saw cuts of a cherry tree trunk with epoxy resin and made a clock.

The easiest and fastest way to repair a wall clock in Prokopyevsk, the "Mix" shopping center.

Top 10 of the most striking, original and insanely stylish wall clocks from the global online store Aliexpress.

On sale from 02.02.2018 on the website / p>

Review of good wall-desk clocks. Bought here - good seller.

Wall clock 3D Diy clock You can order a clock here Cool and unusual Large.

A very beautiful and inexpensive entourage thing. The starting price is only 1000 rubles! Place your bets, gentlemen! Send.

Clock style - Wall Interior Movement type - Quartz Case width - 310.00 Case height - 310.00.

Wall clock ОЧЗ with quarter strike 1962

Wall clock Energy EC 02 ——————————————————– Wall clock Energy EC-02 will decorate the interior.

We make a wall clock with our own hands. I saw such a clock in one of the apartments and thought that it might be.

Video blog about design, architecture and style. Ideas for those who equip their house, apartment, cottage, garden.

Repair of a non-working, new, quartz, Chinese wall clock mechanism. I took it here:.

Video about how I installed the clock on the wall. The watch looks pretty good, I have never regretted a purchase.

Cool electronic clock on the table or on the wall - Aliexpress. LINKS - Save.

In this video, I share my experience in repairing quartz watches: they lagged behind with a "healthy" battery.

Wood, carving, toning, painting; m / c, casting, mount; glass. Dimensions: 51x20x15 cm. This type of wall.

Video (click to play).

How to fix an old wall clock Amber clock 1965. Oryol Watch Factory (OCHZ Yantar). Orlovsky.

Rate the article:

Grade 3.2 who voted: 82

Striking wall clock amber DIY repair

Popular

Do-it-yourself pump repair mazda bongo friendy

DIY engine repair stand

DIY hp laptop repair

DIY apartment renovation ideas

New items

Do-it-yourself repair of the dishwasher krona bdx 60126 ht

DIY sable repair 2752

Do-it-yourself Chevrolet Niva CV joint repair

DIY electric lawn mower repair