Disk drive DIY repair

In detail: do-it-yourself disk drive repair from a real master for the site my.housecope.com.

The situation is familiar to everyone: we insert a disc into a DVD player, and the disc is "unreadable".

There are two possible reasons:

2. Malfunction in the DVD drive.

For example, DVD HYUNDAI consider one of the options for repairing a DVD drive with your own hands... At first, the DVD “stopped reading discs”, and the malfunction sometimes manifests itself and disappears, as a result, it stopped working altogether.

First, we always check the output voltages from the power supply. Is the voltage normal? Then we look at the disk drive, for this we unscrew it and disconnect all the connectors.

We check visually connectors, cable, soldering, etc.

If the visual overview didn't give anything, let's move on.

Next, you need to ring the loop that goes from the board to the head.

During operation, the drive head constantly moves from place to place. As a result, it turned out that the four outer conductors of the loop are in a cliff, the rest are already ready to come off too. I tampered with the insulation with a needle. Here you can see the broken tracks.

If the break is at the very beginning or end of the loop and its length allows it, then you can carefully cut the end of the loop with scissors and insert the loop into the connector.

But sometimes it is useless to repair the loop, it is constantly in operation, it moves and bends, if it is soldered, it will break off again after a while. We need to change. But the problem is to buy exactly such a train is very difficult. But there was a way out! An old, unusable drive from a computer turned out to be at hand. True, the train from it is wider and longer, but the distance between the conducting lines and their thickness are the same.

But it's even good that it is longer, because it will bend less, and there is enough room for it. Contacts fit perfectly, one to one!

Video (click to play).

We accurately measure the required width of the train, it is better to make it a little wider, and then carefully trim it to the desired width. Everything must be done carefully, especially the edges of the train. Now we put it in place.

We check the operation of the drive. So that the train does not cling to anything.

Putting the DVD player together in reverse order. We put the drive, board, cable and connectors in their places, close the case, and enjoy watching your favorite films

Good luck with the repair! Visit our Forum.

Lightsaber (Eng. Lightsaber) - this fantastic weapon is known to many from the fantastic saga "Star Wars". It can be found in science fiction films and stories.

There are many articles on the internet on how to assemble a lightsaber. They are basically based on one principle: placement of multi-colored LEDs in a long tube. This imitates a laser beam. But nowhere is the imitation of the sound of this ray found.

Detailed video instructions for replacing some matrix models later in this article.

A split system (air conditioner) is now in almost every home. Let's figure it out - how does the split system (air conditioner) work?

Laser drives are widely used in electronics. Any DVD-player, CD / MP3-tape recorder, music center are equipped with a laser drive.

In most cases, such devices are repaired precisely because of the breakdown of laser drives.

Malfunctions caused by a breakdown of a laser drive are quite similar, and boil down to one thing - either the laser disc cannot be read, or the playback of music (CD / MP3) or video (DVD) fails.

It should be noted that the service life of a laser diode, which is included in any disk apparatus, is on average 3-5 years. It would be naive to think that a DVD player will last 10 years or more! Take a look at your DVD player manual ...

In general, the first thing to ask when a disk apparatus is brought to you for repair is how old the apparatus has been and how intensively it has been used. If the answer is 3 or more years, then the probability that the optical unit is faulty increases dramatically. How often the device was used is also important, because a laser drive is an electronic-mechanical device. The number of miniature motors in one laser drive is unlikely to be less than 2-3.

The first of the three - spindle drive. He is responsible for spinning up the laser disc. A very large number of malfunctions are associated with it. Here's an example.

Second - optical block drive. This drive is responsible for positioning the laser head along the disc. It rarely fails.

Third - loading / unloading drive (LOAD). Unloading and loading the disk into the drive. Malfunctions of this engine are quite rare and usually easy to repair.

In practice, such a malfunction is common. Mostly in CD / MP3 car radios.

The sound often disappears during playback. It appears abruptly and also disappears. Stuttering is present.

Have DVD players the malfunction manifests itself as follows.

The disc is read for a very long time, after which the display shows (ERROR or NO DISK). The disk may freeze up accidentally. Reinserting the disc solves the problem and the recorded disc plays back normally.

The reason for this "incomprehensible" behavior is not associated with a malfunction of the optical laser unit, but with a malfunction of the spindle drive.

The fact is that the spindle motor must spin up at a certain speed. The speed is adjusted by a feedback system. So don't think that the disc is spinning by itself. Applied 3 volts to the engine and that's it! Not! The rotational speed of the disk is regulated by a complex adjustment system. If the spindle motor is defective, then even the correction system does not handle well and malfunctions occur. The engine does not give out the required rpm, it “fails”.

Therefore, if the malfunction described below appears, do not rush to replace the optical laser unit!

Replacing the spindle drive is cheaper than buying an optical laser unit. You can temporarily replace the drive with a motor from another device or find a suitable one in the store.

A very common problem with CD / MP3 recorders with vertical disc installation.

The disc spins up, but the disc does not load. Writes ERROR or NO DISK.

The optical laser unit is afraid of dust and dirt... A thin finely dispersed dust deposit on the upper lens is enough for the disc to stop being read. Vertical disc recorders are more vulnerable to dust, the disc is loaded from above and the amount of dust that gets in increases.

Disc car radios in this case are more protected, they have a slot loading disc.

Fine dust deposits can be removed from the surface of the lens of the laser unit with an ordinary cotton swab or just a piece of cotton wool. Moisten cotton wool with cleaning agents no need, you can ruin the lens! Using a cotton swab 3-4 times on the surface of the lens in a circular motion. Making sure that there are no residues of coarse dust on the lens and that's it!

Do not press on the lens, it is attached to spring cables! They supply power to the focusing electromagnet. They are quite sturdy, but with excessive force they can be damaged.

It is not uncommon that after such a simple cleaning, the operation of the device is completely restored.

Read also: DIY abs pump repair

The main difficulty in this operation is to properly disassemble the device and get to the laser head. This is most difficult for music centers with a 3-disc loading unit or changer (when the discs are placed in a box - like plates in a dryer), as well as for car CD / MP3 players and DVD players with a slot loading disc.

Therefore, on the pages of the site, I posted information on disassembling all kinds of CD drives:

These techniques will help if you need to disassemble a CD drive, but there is no experience in this matter.

Sometimes cleaning the lens does not help. The reason is that there is a prism inside the optical unit, dust will settle on it over time. It makes no sense to disassemble the optical unit. Better to replace the entire block.

When repairing electronics with faults that clearly indicate a defect in the laser drive, you can use the following techniques:

Check the mechanical part of the laser drive for jammed gears, carriages, serviceability of flexible connecting cables. It is better to “ring” flexible cables with a multimeter, and it is better to check with a replacement. Very often the loop “rings” by the multimeter as if it is working, but since it bends during operation, the bad contact again makes itself felt.

In DVD players, the “weakest” ribbon is the one that connects the laser head to the main board. Replacing it often fixes a problem with a “freeze” disk, bad or long loading of the disk, and playback failures.

Check if there is a laser light. After inserting the disc, the red laser turns on (only for DVD) for a few seconds. At this moment, it is necessary to check the presence of a glow while looking from the side. Remember! Laser is harmful for health! Direct eye contact with the laser beam can result in loss of vision. Be careful!

Clean the lens of the optical unit. How to do this has already been described.

Visually trace the loading of the disc, its spinning. Replace the spindle drive using the substitution method.

If possible, replace, at least temporarily, for inspection, the laser optical unit. Here's how to quickly replace laser in DVD.

In addition to the laser, there may be other causes of the malfunction. I have already talked about the main malfunctions of DVD-players.

The topic of repairing disk devices is quite extensive, here are just a few recommendations and tips. For a deeper understanding of the operation of laser disc players, it will not be superfluous to familiarize yourself with the general principles of operation of such devices. I think the book “CD-players. Circuitry "Avramenko YF, will be very useful for understanding the operation of disk devices.

Disk drive repair. Prevention and Treatment.

Mechanical failures are the main causes of drive failures. They make up about 75-80% of the total number of malfunctions and repairs associated with it. Moreover, most often the reasons for the failure of DVD drives (any, not only computer ones) are contamination of the moving parts of the disc transport mechanism and dust accumulated on the optics. Repairing a drive will almost guarantee it will be adequate to the cost of a new one, so we carefully read and weigh whether the skin is worth the candle.

Repairing a floppy drive is not a trivial task.

The presence of dust and dirt on the moving parts of the mechanism, especially on the edges of the movable carriage sled, makes it impossible to lock the drive mechanism holding the disc, as a result of which the device does not fix the disc and constantly throws it out. If, on the contrary, the drive ejects the tray and immediately picks it up, then, most likely, the cause of the defect is the failure of the tray position sensor. The fact that the tray is thrown out is determined by the drive with the help of a contact sensor, which should be found, try to correct its position, repair or replace. Repairing the drive itself is not necessary here; from time to time, just make sure that dirt does not accumulate in the places where the slide moves.

In order to clean the dust from the drive of the drive, you can first confine yourself to partial disassembly (pull out the tray and remove the front panel), and then blow the interior of the drive with a vacuum cleaner configured to blow out the air flow. It's not about repairing the drive yet.

The optical drive system often fails due to dust accumulated on the focal lens or prism. If blowing out the device does not help, you can try dusting the lens with a soft flannel or a brush, as shown.

Remember that under no circumstances should you use alcohol or solvents for cleaning!

The focus lenses of most modern optical drives are made of organic plastic, and the solvent will irreversibly damage their surfaces. It is best to wipe a heavily soiled lens with a piece of stiff paper (at worst with a cotton swab, being careful not to leave any lint). This operation is carried out with extreme caution, as the suspension of the laser itself can be damaged. In this case, repairing a drive will be expensive, almost equal to the cost of the drive itself.

The situation is more complicated with the prism that stands behind the lens - it is extremely difficult to get to it. Moreover, the head, as a rule, is not collapsible, but even if it is disassembled, then you can knock down its settings. Therefore, for most drives, a dirty lens means it is completely unusable. Sometimes the optical system fails even due to an ordinary hair caught on the prism - in this case, again, you can try to blow through the system with a powerful stream of air. Otherwise, the repair of the drive (its cost) will be unreasonably high.

By the way, it is not recommended to use special discs for cleaning optics, supposedly specially designed for this. Most of them will not only fail to clean your drive, but they can even seriously damage it. After all, modern optical drives spin the disc to a very high speed and at the same time have a very delicate reading head, so if your device is dear to you, then do not clean it with the help of such devices. This will no longer be a repair of the drive, but an almost deliberate destruction of the drive.

However, most drives operating under normal conditions do not survive to the stage where dust can cause failures. Most often, the plastic of the lens simply becomes cloudy from time to time and / or from overheating of the drive in the system unit. Disk drive repair consists of an expensive replacement of the laser read head. However, such a malfunction accounts for no more than 10% of cases. Here you can, of course, advise to increase the intensity of the laser glow. For this, the variable resistor installed on the carriage with the laser is regulated. Turn the slider of this variable resistor clockwise by 20-30 °, after which the fact of rotation of the drive motor is checked when the disk is installed. If the disk does not begin to rotate, then turn the variable resistor slider another 20-30 °, and continue this way until the motor starts (it should start and for some time - about 10-20 seconds - rotate at a constant speed) ...

The need to rotate a variable resistor that regulates the intensity of the laser light is due to the fact that over time the power of the laser light flux decreases (aging of the elements, clouding of the lens, etc.), however, after such an adjustment, the optical system usually does not last long anyway. Such allegedly repairing a drive is no longer practiced.

You will hardly be able to eliminate other malfunctions of the optoelectronic information reading system on your own. Despite its small size, the optical system of the DVD drive is a very sophisticated and precise optical device, including servo control systems for the rotation of the disc, positioning of the laser reader, autofocus, radial tracking, and a readout and laser diode control system. Repairing the drive is not worth it in this case.

Typical signs of a malfunction are either the lack of rotation of the disk, or, conversely, its constant acceleration to the maximum rotation speed.When you try to remove a disc from a faulty drive using the controls, the carriage opens with the disc rotating on it.

In the operation of a working system, the following phases should be clearly traced:

• start and smooth acceleration of the disk;

• steady state of rotation;

• interval of braking to a complete stop;

• removal of the disk by the carriage tray from the engine spindle and its removal out of the drive.

You can check that the optical system of the drive is working properly by opening the case of the device and observing its operation. You can verify whether the disc spins up after installation by connecting only the power cord to the drive (the data cable is not connected in this case). If the disk does not rotate after installation, then check whether the laser is shining when the carriage is installed in the working position, but without the disk. Sometimes the glow of the laser is not visible in daylight, so the room needs to be darkened. Observation of the laser lens should be carried out from different angles.

In modern optical devices, the presence of a disc is controlled by the laser itself. If the photosensor installed in the laser carriage receives a reflected signal from the disk, then the electronic circuit perceives this signal as “presence of the disk” and only after that generates a command to turn on the main engine of rotation. Therefore, if the intensity of the laser light is insufficient, then the disk will not spin up and the repair of the disk drive will become inevitable.

The servo system for positioning the information readout head provides a smooth approach of the head to the specified recording track with an error not exceeding half the track width in the search modes for the required piece of information and normal playback. The movement of the read head, and with it the laser beam along the disk field, is carried out by the head motor. Engine operation is controlled by forward and reverse motion signals from the control processor, as well as signals from the radial error processor. Typical signs of a malfunction are both the erratic movement of the head along the guides and its immobility.

You can visually check the correctness of the focusing system. At the start of the disc, the control processor generates correction signals that provide multiple (two to three attempts) vertical movement of the focus lens, which is necessary to accurately focus the beam on the disc track. When focus is detected, a signal is generated to enable reading of information. If after two or three attempts this signal does not appear, then the control processor shuts down all systems and the disk stops. Thus, the operability of the focusing system can be judged both by the characteristic movements of the focal lens at the moment of starting the disk, and by the signal to start the disk acceleration mode upon successful focusing of the laser beam. Other parameters of the correct operation of the optical system are not visually determined.

Optical drives also have many mechanical components that require lubrication of the rubbing parts. The lack of lubrication leads to the fact that the drive hardly pushes the carriage with the disk, and the carriage lock can generally jam, and then the use of the drive will become completely impossible. The lubricant must be applied carefully, after having completely disassembled the device (the places where it is required are usually clearly visible). Before lubrication, it will be useful to clean the lubrication points of dust and dirt. The fact is that if you miss the moment when it is required to apply lubricant, then the difficulty in sliding will lead to mechanical damage to the parts of the transport mechanism or to a violation of its adjustments, which, in turn, will entail either the stop of the carriage mechanism in an intermediate position, or slipping of the disc during rotation time.

A similar situation can arise due to grease on the friction surfaces of the disc holder due to the frequent use of dirty DVD discs, which ultimately leads to unreliable operation of the drive, even to a complete stop.

Contamination of the disc drive seat and poor clamping of the disc to the seat can be eliminated by cleaning the disc seat with any cloth moistened with alcohol.

You can check if there is enough force to hold the disc against the seat when trying to play a regular disc. If there are no errors or failures during disc playback, and the disc with computer data is still unstable to read, you can take additional measures - bend the springs or increase the weight to increase the pressure on the disc from above.

Other mechanical failures include jamming of the disc on the transport carriage (in this case, the disc does not spin at all). Sometimes this happens because the seat of the disc spontaneously descends along the motor shaft and the disc touches the elements of the transport carriage. To eliminate this defect, the seat is moved upward along the shaft and its height is selected "by poking" so that the disc rotates without touching the structural elements, and also so that the drive ensures stable reading of all discs. After that, the position of the disc seat is carefully fixed on the shaft.

However, the listed mechanical faults relate mainly to simple mechanisms of relatively cheap drives. Expensive models, as a rule, have complex mechanisms, for which the main type of mechanical failure is fatal breakdown of the mechanism parts. Most often this happens due to the fact that the user, instead of using the control buttons, pushes the carriage with the disk inside the drive by hand. The consequences of such actions can be the most unpleasant. If a dirty and running mechanism is enough to clean, wipe, and lubricate it to perform its functions properly again, rushing and applying excessive force to the disc tray can cause breakdowns that will cause expensive and time-consuming drive repairs.

Finally, electronic component malfunctions are possible. However, their share is unlikely to exceed even a small fraction of all breakdowns. Unfortunately, modern optical drives are very complex electronic systems, and a faulty microcircuit does not differ in appearance from a working one. Accordingly, repairing a drive at home without preparation is impossible.

Now drives may cost less than a network card or video card, but that does not mean that they are just as simple. The optical drive has a rather complex design and, in addition to the mechanical part, contains at least two microcontrollers, a signal processor (DSP), a secondary voltage source, circuits for controlling mechanics, etc. Moreover, most of the microcircuits used in modern drives are specialized, and therefore, repairing a drive in its electronic part is hardly advisable.

Note that in an optical drive it is quite difficult to diagnose an electronics failure even with a sufficient degree of reliability. Indeed, depending on the error correction strategy chosen by the manufacturer for a particular model and, accordingly, on the complexity of the processor and the device as a whole, in practice this or that drive can work with different disks in different ways. This, by the way, explains a common situation when your disc is easily read on a colleague's machine, but your own PC does not even see it. In cheap models, the correction system can correct only one or two minor errors in a frame of information, and a complex expensive system can restore even serious and extended destruction of information, and it does this in several stages using a complex algorithm.So the repair of the drive in this case will not work due to the absence of a malfunction as such.

Each manufacturer uses its own chipset or completes it with products from different manufacturers, and, of course, does not attach a description. Due to the fact that for each specific device it is necessary to look for specifications for almost every microcircuit separately, often even service center specialists cannot always restore the functionality of your device. If only because the repair of the drive will not be economically justified.

In short, if after cleaning, checking all the wires and connections, as well as system settings, your DVD drive does not work, and the warranty for it has already expired, you may end up with a situation where you just have to throw out the old one and buy a new one.

How to repair a CD-DVD drive yourself?

This is a short story with pictures on how you can revive a CD-DVD, and probably a Blu-Ray drive, without resorting to expensive professional help. There are several common reasons that can lead to complete or partial inoperability of the drive. The elimination of these causes is not a repair, but rather a maintenance of the CD-DVD-ROM and may well be performed by a user with some electronic skills. Learn more at my.housecope.com/wp-content/uploads/ext/1284

Worn drive belt (belt).
Increased friction in the loading mechanism.
Dirty laser lens.
Decrease in laser efficiency.

Removing any of these causes requires partial disassembly of the drive. The design of the drives may vary, so the accompanying pictures should not be taken absolutely.

For preventive maintenance, we need the following tools, materials and components. my.housecope.com/wp-content/uploads/ext/1284

A paper clip.
Phillips screwdriver.
Medium brush.
Calico (cotton fabric).
Silicone grease SI-130.
Belt.
Cleaning cloth.
Thin screwdriver.
Tweezers.

Begin. Disconnect the cables from the drive and unscrew the mounting screws. We take out the drive from the case of the system unit.

Disassembling any CD-DVD drive begins with pulling out the tray. To slide out the tray, you first need to make a simple paper clip fixture.

Carefully, pushing the end of a paper clip into the technological hole on the front panel of the drive, we grope for the part of the mechanism that is responsible for blocking the tray. This detail is located strictly opposite the hole. Click on it and the tray slides out slightly. Now you can pull it out with your fingers.

We squeeze out the latches securing the front panel of the drive. First, squeeze one of the side latches.

Then, we squeeze out the latch located at the bottom of the drive, and the other side latch.

Pull out the front panel, unscrew the four Phillips head screws and remove the metal casing panels.

We squeeze the latches and separate the tray from the main mechanism.

Thoroughly clean the mechanism from dust and dirt with a brush. If the old grease is heavily contaminated, then we remove it with coarse calico and apply a new grease.

We replace the worn out belt with a new one. Then we wipe the belt and the inner surfaces of the pulleys with a cleaning cloth or coarse calico dipped in alcohol.

Wipe the laser lens with a cleaning cloth. Dust deposited on the upper surface of the lens may not be visible to the naked eye, but it is almost always present there.

If the drive is very old or it is known that too many discs have been written to it and there is a read or write problem, then you can try to increase the laser current. This rather delicate operation takes patience and can take quite a long time. Do not start this procedure if your drive simply does not read a few old discs or discs written on other people's drives.This can be caused by a lot of different reasons and the magnitude of the laser current is here in 38th place.

It is best to adjust the laser current when the actuator is in a semi-disassembled state.

To start the drive without the shroud and front panel, you will need to remove the front wall of the disc tray.

Somewhere on the carriage with the installed laser there is a small-sized potentiometer, the position of the slider of which determines the laser current. The location of this potentiometer depends on the design of the actuator.

Before turning this screw, be sure to sketch the position of the slot in order to have a reference point, and indeed, so that you can, in case of anything, return it to its original position.

Turning the screw 10-15 degrees, first in one direction and then in the other direction, each time we check the reading quality in some program, for example, Nero DiscSpeed.

It is only advisable to check on several types of media at once, for example, CD-R and CD-RW or DVD + R, DVD + RW, DVD-R, DVD-RW, etc. It is probably not necessary to check all types of supported media, but check at least the ones that you use all the time.

Multipurpose universal drives are rather compromise products and therefore they often read some types of discs better, and some worse. For example, by increasing the laser current, you can get perfect CD-R reading and make half of your CD-RWs unreadable.

The assembly does not present any difficulties, except for one moment. When inserting the tray into the loading mechanism, it is required to align the locking mechanism of the loading mechanism with the guide slot located at the bottom of the tray.

The slide is usually spring-loaded, so you need to fix the slide in the correct position using tweezers or another suitable tool before sliding the tray into the guides. In the photo, the position of the slider is fixed with an awl.

If, quite by accident, you have at your disposal a small set of belts of different diameters, then you just need to choose a suitable copy. If there is no such set, then you will have to buy a belt.

And although the era of video and audio tape recorders has passed, on all kinds of radio markets you can still buy rubber belts in stock.

When buying a belt, you need to pay attention to several of its parameters at once, such as: section, diameter, elasticity and quality of vulcanization of the rubber from which it is made.

The section of the belt can also be determined by eye, since the likelihood that you will be able to find a belt of a strictly corresponding section is small.

The diameter of the belt can be determined by attaching the old belt to the new one and make sure that the diameter of the new one is slightly smaller than the old one.

Elasticity can be measured using an impromptu stand, like the one in the picture.

I usually check the properties of a belt by touch without any dynamometers.

The quality of the vulcanization of rubber can be determined by the color and tactile sensations. The color of the "wrong" rubber is deep black and the surface is smooth and highly reflective. While the "right" rubber has a slightly grayish tint and a more matte finish.

Also, the quality of rubber vulcanization can be determined by the recovery time of the original size. For the test, you need to stretch the belt strongly with your fingers and very quickly drop it flat on a flat surface. The faster the belt takes its original size, the higher its quality. If you can notice by eye how the diameter of the belt changes, that is, it seems to shrink, then such a belt will not last long and it is better not to use it at all. However, it is not a fact that you will find a high quality belt at the bazaar, and even exactly the same as required. Therefore, for lack of the best, you can buy what you have, but adjusted for diameter, section and elasticity.

And so, all four of these parameters affect the properties of the belt. When choosing a belt, you need to take all of them into account.If the section of the belt is slightly smaller, then you need to choose the belt a little shorter and vice versa. If the quality of vulcanization is low, then you need to choose either a slightly larger section or a slightly smaller diameter.

If the belt is too tight, it can lead to seizure or premature wear of the disc loading mechanism. If the belt is too loose, it can cause it to slip relative to the engine pulley.

If there are several belts with similar properties in the bazaar, then it is better to buy several different ones at once in order to find the most suitable one at home. The price of a belt for a CD-DVD drive can range from $ 0.3 to $ 0.7.

You can fix a floppy drive malfunction with your own hands, in this article we will try to disassemble the principle of operation of a CD-ROM, and also consider one of the ways to bring it back to life using the example of the Samsung SCR-2431 model.

So, we have a problem: the drive does not read discs. The reasons for the breakdown can be mechanical or hidden in the electronics. All electronics malfunctions are the business of specialists, an attempt to independently repair a computer at home will lead to irreversible consequences.

The mechanical part consists of:

spindle motor;
optical head unit;
a drive that moves the optical head;
disk loading system.

The function of the motor is to drive the disc into rotation at high speed. The optical head unit consists of:

laser emitter;
photodetector;
focusing system;
preamplifier.

The focusing system tracks the beats of the disk in the vertical plane. A separate motor is responsible for the radial movement of the optical head; it is connected by a worm or gear drive with a carriage moving along the guides.

tray;
motor driving the tray;
a mechanism that sets the disc to the working position by raising the mechanics with the motor, or by lowering the disc onto the spindle motor.

Pull out the drive tray, removing the lock: insert a straightened paper clip into the small hole on the front panel, gently press. We unscrew the screws securing the top cover, we get access to the insides of the drive. Before proceeding with the repair of your computer, remember that you cannot do the following:

do not look directly into the laser lens - you can seriously damage your eyesight!
Do not leave the disc in the disassembled drive - spinning at high speed, it can break off the motor shaft and cause serious injury!

We proceed to the analysis of faults.

In the vast majority of drives, racking-out-racking is carried out using a separate motor. In the model considered here, this function is performed by a motor that moves the optics carriage. The sliding tray presses on a lever that pushes the carriage towards the gears connected to the engine, at the same time the tray comes out of this area. The stand with the disc is lowered and the disc is pressed against the spindle motor shaft. A sophisticated lever system creates an increased load on the last tooth on the tray. In addition, the gear driving the tray only half touches the line of teeth - the result is shearing off the lower half of the last tooth. A symptom of this malfunction is an incomplete latch of the tray and the impossibility of its extension, or its extension, accompanied by grinding sounds.

The solution to the problem is to restore the erased tooth. Put a small amount of melted plastic on it. After it has hardened, shape it into a prong shape using a file. You can also try raising the drive chute to move the gear to the same height as the top half of the tine. We also recommend lubricating the mechanism and checking the integrity of the rubber belt that drives the tray, which is available in some models - the causes of the malfunction may be hidden here.

In the case when everything is normal with the load, but the drive still does not function, it is necessary to check the system that moves the optical head and the spindle motor. Connect the opened disk drive to the computer and make sure that the engine starts up for a short time, and that the carriage and laser move when closed. You will notice a red glow from the laser (viewed from a specific angle).

The lack of rotation of the electric motor, as well as the immobility of the carriage, indicates a malfunction of the control microcircuit or the engine itself. Let's check the performance of the engine: by disconnecting it from the printed circuit board, apply a voltage of +5 V, connecting it to an external source. If the problem is in it, then you will have to replace it with an analog, if in the microcircuit, then only a specialist will help you. The immobility of the carriage can be caused by wear of the elements of the worm (gear) transmission. The solution to the problem is to replace the part.

It is easier to repair the drive at home if the discs are not readable, but the laser is on, the engine and carriage are working properly. The problem may be rooted in:

misalignment of the spindle motor;
contamination of the landing site for the optical system and disc.

Wipe the laser lens with a soft brush, grease the axles that move the gear carriage and guides with grease. Check and retighten the motor mount if necessary. Wipe the rubberized ring located on the seat with alcohol. We assemble the drive and check its performance. In the overwhelming majority of cases, the malfunction is eliminated, but if the functionality cannot be returned, then you need a wizard.

The Computer Support Center is always ready to assist in the restoration of the drive, as well as return the lost functionality to the system. Call us - we will quickly solve any problem!