Dualshock 4 DIY repair

In detail: do-it-yourself dualshock 4 repair from a real master for the site my.housecope.com.

The main goal was to replace the worn-out sticks, but in the process a couple of problems arose, the answers to which I never found on third-party resources, and the problems after opening were not only mine.
I decided to make a manual for replacing sticks, and avoiding / repairing these problems, maybe someone will come in handy ..

1. Unscrew the 4 bolts at the back of the DS4

There is emptiness under the sticker, although it feels like a hidden bolt

2. We begin to boldly snap off from the bottom

3. As it was revealed, we take out the battery wire, the loop of the joey wall, and the rubber band of the reset button

4. For convenience, you can remove the buttons, be careful with the springs, it is because of them that I had 1 button after assembly! (very easy to insert, all grooves are visible)

5. There is still a bolt under the battery.

6. Gently pull out the touchpad cable using tweezers by the blue strip.

7. Change sticks and collect everything back.

After collecting, like many, the touch panel did not work for me.

At first glance, it is not collapsible, the train holds on tightly, but in fact it falls out easily, but does not fall out completely because everything is twisted there and goes at an angle.
It opens in an elementary way, since glued with ordinary double-sided tape. You can warm it up with a hairdryer for 10 seconds and open it with my hands, I personally picked it with a knife.

We insert the cable, assemble the panel, falling into the grooves, collect the joy.

The joystick of any game console is the part most susceptible to various breakdowns. The reason may be trivial wear and tear of parts, careless handling. Moreover, the latter, unfortunately, most often leads to premature repairs. Often, players during the game drink drinks, food, can carelessly throw the gamepad. But even if you are sensitive to your console, wear and tear cannot be avoided.

Video (click to play).

To clean and repair your PS4 controller, you need to know how to disassemble it.

Since active participation in games involves frequent and strong pressing of the buttons, rotation of the sticks. Usually they are the first to fail. The material from which the sticks are made is erased and torn. To carry out repairs, you need to carefully disassemble the PS4 joystick. And also it will be required to replace the battery.

Repairing a PS4 joystick is required when the following symptoms appear:

any buttons stuck or do not work;
there is mechanical damage to the parts;
various errors appear on the screen;
communication between the console and the gamepad often disappears;
I can't connect the joystick and the console.

The main problems when using Dualshock 4 gamepads:

Sticks are highly abrasive and often need to be replaced. To prevent this problem, buy silicone rubber tips and your sticks will last much longer. You can change the native sticks to metal ones, but they are less convenient to operate.
The 3D analog is the mechanism on which the sticks are attached. Over time, it breaks down, and the character of the game stops responding to the movements of the stick left-right or forward-backward. Or it sticks in motion in one direction. In this case, the 3D analog needs to be replaced to solve the problem. It is quite difficult to change it at home, especially if you have no experience.
Broken shackle of the R2 button is especially common among fans of sports simulators. And also you need to pay attention to the silicone rubber band under the button. Replace if worn.
Conductive rubber bands under the cross and control buttons (square, triangle, circle and cross). Are prone to wear and tear, and if the gameplay does not respond well to any of these buttons, then it needs to be replaced and the problem will be solved.

You can use the services of special firms, but in fact, if you just need to replace buttons or some simple parts, then it is quite possible to repair the PS4 joystick yourself. If the set-top box does not see the joystick, then, most likely, its Bluetooth module is broken. It is almost impossible to replace such a part on your own without special materials and devices. In such cases, it is better to trust specialized firms to repair gamepads.

Replacing and repairing any parts of the controller begins with its correct disassembly. In this case, it is important:

Strictly follow the order of actions.
Do everything carefully, do not pull, pull or press forcefully.
Record or photograph your actions in stages, so that later you can easily and correctly assemble the gamepad back.
It is advisable to use a small magnet on which to fold the screws that you unscrewed. This way, none of them will fall, roll away or get lost.
Gently take parts with contacts and microcircuits by the edges, hands should be clean and dry.
Before disassembling your PS4 controller, prepare yourself a work area with enough space to accommodate the parts to be removed.

After preparing everything necessary, we disassemble the PS4 controller step by step according to the instructions:

Unscrew the 4 screws on the back of the case.
It is necessary to carefully bend the inner clips, which are located on the sides near the R1 and L1 buttons and near the headphone jack. In order to detach them, use a thin screwdriver, or better with a special spatula for disassembling the electronics. You can buy it in specialized stores or on the Internet.
Begin to peel back the clips from the ones near the connector. Insert the paddle between the bottom edge of the connector and the controller body. Push and tilt a little, the clip should come off easily.
Now carefully unfasten the clips on the sides of the controller.
To remove the back of the case, pull the triggers and move up and forward to detach the cover.

Disconnect the ribbon carefully by taking it closer to the connector.
Remove the battery by disconnecting the connecting wire. Do not pull on the cord itself, keep close to the connection.
Remove the plastic battery holder by releasing the two latches on the sides.
Disconnect the touchpad cable.

Unscrew the screw on the main board.
Since the board is soldered to the vibration motors, carefully slide it down. On newer DS4 models, the board is fixed on the plastic part, and does not hang on the wires, so this item is not applicable for them.
Now, carefully grasp the vibration motors and remove the plastic part that held the board and sticks.
Now you can remove the silicone rubber bands under the buttons and the buttons themselves.

These are the general instructions for disassembling a Dualshock 4 controller. You may not need to disassemble it completely, it depends on what exactly needs to be repaired or replaced.

After you have completed your PS4 controller repair, you need to properly reassemble it. To do this, simply follow all the steps in the instructions in reverse order. Pay attention to the following important points:

After replacing the buttons, the conductive spacers must be properly secured to the plastic guides, otherwise the buttons will not work.
When installing the plastic frame, be sure to insert the ribbon cable through the hole provided for it.
Make sure the touchpad cable is flat and secured with a latch.
When installing the back of the case, insert the ribbon cable in the correct direction. Otherwise, the light bar and charging will not work.

Many specialized workshops are engaged in the repair of gamepads. But the considered instructions on how to disassemble the joystick of the PS4 console on your own shows that you can cope with elementary actions at home. This is a replacement for sticks, triggers, batteries, cross and buttons. You just need to disassemble the controller, change the part and assemble it.

It is not recommended to carry out actions related to the use of a hair dryer, soldering iron, thermal tape and similar materials and tools by yourself.For example, separate the touchpad from the plastic cover or change the 3D analogue. Rough handling can lead to breakage. If you have any tips for disassembling and repairing PS4 gamepads, leave comments and share your opinion with other users.

Published by the VP Editor, 04/13/2018. Posted in Articles and News

The longer you play on PS4, the more it will wear out and get dirty DualShock 4 gamepad.

If you have the right tools and enough experience to disassemble the PS4 joystick yourself, you can change a torn or broken stick, clean the "insides" from dust and change individual buttons and parts.

About, how to disassemble a PS4 gamepad, read this article.

There are several revisions of joysticks. Depending on the versions, disassembly method may differ: location of clips, loops, etc.

If you suspect that your joystick needs major repairs, such as replacement of chips and important parts, contact the workshop.

This manual is for informational purposes only. If you are not confident in your abilities, contact a specialist. In the workshop, cleaning and / or repairing joysticks on average take no more than 30-60 minutes.

PS4 Joystick Disassembly Begins from the preparation of the workplace and the necessary tools.

Make sure on the table there are no unnecessary items and rubbish. Leave only those tools that are useful for your work. For convenience, you can prepare small magnet, to which it is convenient to attach the bolts so as not to lose them.

Next you need prepare tools, with which we will disassemble the PlayStation 4 joystick:

Metal shovel for electronics disassembly;
Small diameter Phillips screwdriver;
Insulating tape;
Clip tool (see below).

Most DualShock 4s cost JDM-011 schematic... All control elements, backlight diodes, touch panel, charging connector, etc. are connected to it.

Also there is a battery inside Li-ion 1000 mAh.

Right and left are located 2 vibration motors.

All buttons, sticks and triggers can be easily replace with new... However, if complex parts or the body of the controller are damaged at the attachment point, it is better to contact a workshop.

1. Let's proceed directly to disassembly. Begin by loosening the screws... There is nothing special about this procedure. The main thing - don't lose anything.

2. Now you need to separate the body by removing the clips, but before doing this, protect buttons R1 and L1: cut off a small strip of electrical tape and glue them, as shown in the picture.

3. Moving on to the clips themselves: you need a spatula insert gently between the charging connector and the case, then pull the handle up (70-80 degrees) and smoothly lower it to a horizontal position.

All latches, except for the top ones, disperse immediately... This method is much more practical, simpler and safer than opening "in a circle" (clips may break).

Don't worry, the headset jack is made of thick plastic, so it does not deform.

4. Now you need remove the fixation of the upper clips... This will require a strong, thin tool such as a hair clip. To get something like a lever it needs to be bent.

Insert the hairpin between the body and the L1 key, and then push down gently. Do the same with the other button.

5. The gamepad can now be disconnected. Press with index fingers triggers R2 and L2 and gradually slide the back cover forward and upward to remove it.

Carefully! Both parts connected by a loop... Do not make sudden movements so as not to break it. Take a closer look at the connector and disconnect the loop.

6. The time has come de-energize the system before disassembly. To do this, you need to pull out the power connector as shown in the photo. The battery can now be put aside and remove the plastic holder.

The holder is fixed with two clamps, which must be disconnected with the same spatula.

Read also: DIY car radio panel repair

Sticks, the first time I ordered a pair and one came as in the photo, the second, as it were, without a rubber knob. I had to order an alternative. I decided not to risk it and made an order for four pieces at once, this time all came in whole and within 2 weeks! Very fast. Good quality! But, the gum is a little more "oak" than the original, but after 10 minutes there is no difference at all.

Unscrew the four bolts at the back (regular chalk Phillips screwdriver (hello XBOX360 gamepad))

We slightly tighten the black (or blue, or red :)) cover and slip, for example, a plastic card, and leave it in this position.

Then we take a minus screwdriver and gently push it inside. Latches next to R1 and L1.

We do this on both sides and release a couple of latches from the side of the headset.

We take out the trains (indicated by the arrows)

We take out the battery connector and unscrew the bolt on the board, just to the right of the connector

Just the characteristics and model of the battery for replacement, there are options for replacing it with a larger volume. LIP1522

We bend the board and remove the sticks.

The removed stick looks like this. We make a new one.

Putting it up in the reverse order. Don't forget to stick in the loops!

Comparison of the original new sticks and the Chinese ones. Visually, there is no difference.

And for comparison, old and new sticks.

You can get used to anything, and the linings served me for a month. I hardly noticed them. But in order not to fence the garden, he still replaced the sticks with Chinese ones. They are slightly different in terms of tactile sensations.But they cope with their task at 5!

Is R2 skipping? Lost L1? Stick sticking? All this can be fixed - quickly and with a guarantee.

PS4 joysticks, while similar in design to other generations of joysticks, have a number of design changes that add both gameplay features and challenges. For instance, the touch panel often fails when liquid gets under it and with minor impacts. The charging port is fragile and is often damaged when connecting the cable. There are also design flaws. For example, most players the R2 button breaks, as well as in a short time stick pads are erased.

Most often, problems with the DualShock 4 are associated with mechanical damage: dropped or jammed buttons, erased or not working sticks, a faulty charging connector. But breakdowns can also occur in the electronic part: the console does not see the joystick, the battery does not charge, vibration does not work, the joystick stops turning on.

We undertake most of the repair work for PS4 joysticks, including after unsuccessful self-repairs. Mechanical problems are usually resolved in a short time - from 15 minutes. Electronics problems require diagnostics and longer repair times.

Joysticks of any game consoles in the process of intensive use are subject to natural wear and tear of mechanical parts. In addition, they often suffer from the effects of various negative factors - falls, bumps, pouring drinks, dust, etc.

The weakest points of the third and fourth generation PlayStation game controllers are the end control buttons: R1 and R2, L1 and L2.

The nature of breakdowns can be different: for someone the button falls through and sticks, for someone it becomes very sensitive, sometimes the plastic fastening of the button breaks off and falls out of the gamepad.

Since the plastic mount cannot be restored, in all these cases, the simplest solution will be to replace the button with a new one. In this case, not only the key itself is changed, but also the metal spring with a lining.

If Round buttons on PS4 joystick don't work or are triggered every other time, the problem may be in a worn out or damaged contact substrate, which transmits signals to the board when the buttons are pressed. In this case, cleaning or replacing the entire backing will help solve the problem.

If sticky button on Dualshock 4stuck or stopped working altogether, you should carry out diagnostics to establish the exact cause of the problem.

To do this, you will have to disassemble the controller using a small Phillips screwdriver and a flat screwdriver with a thin wide slot.

The order of performing the actions is as follows:

Turn the joystick over and unscrew the four mounting screws;
Gently pry off the plastic cover on the handles of the gamepad with a flat screwdriver (so as not to damage the case, the screwdriver can be wrapped in a napkin or handkerchief);
Then we turn the controller upside down and gradually detach the plastic cover on the left and right sides of the case;
Next, you need to detach the plastic in the area of the triggers. To do this, turn the joystick with the triggers towards you and carefully detach the plastic, moving first from the right triggers towards the Share button, and then to the left triggers;
Disconnect the two parts of the controller case. This must be done very carefully so as not to damage the train. After removing the cover, the cable should be disconnected

If there are problems with the end control buttons (R1 and R2, L1 and L2), there is no need to further disassemble the controller, since after removing the case cover, full access to them is provided.

We make a visual inspection of the keys for mechanical damage.
We check if the spring has fallen out of its place.If the button itself is damaged, it must be replaced. This is done very simply: the old key is removed from the seat and a new button is inserted. Since the new buttons are sold with a spring, both parts must be replaced.
If all the buttons are intact, and the springs are in their places, but the keys stick, you should thoroughly clean all the "insides" of the controller from dust and dirt with a cotton swab and alcohol.

VIDEO INSTRUCTION

Another common problem faced by PS3 / PS4 users is faded (torn) sticks.Fortunately, the controllers are fully repairable, and the sticks can be considered consumables.New sticks can be purchased in specialized stores from stock, but it will be cheaper to order them on Aliexpress.To replace the sticks, you must completely disassemble the gamepad. Image - Dualshock 4 DIY repair

Install the stick button in place and check the functionality

Remove the plastic cover of the controller housing (the process is described above);
Disconnect the battery by disconnecting the white connector with two wires from the joystick board itself .;
Unscrew the fastening screw located under the battery;
Next, you need to disconnect the cable and remove the controller board itself from the front button part. In order not to damage the cable, it should be removed very carefully using tweezers, simply by pulling the tab

Once the DualShock is completely disassembled, you can easily repair any button on your PS3 joystick. So, to replace the sticky stick, you just need to remove the old one and replace it with a new one.

VIDEO REVIEW