Electronic cigarette malfunction DIY repair

The mechanism of an electronic cigarette is rather complicated. Before entering the market, these products undergo quality control, but during operation, for one reason or another, malfunctions in its operation are possible. The cause of damage can be both prolonged use and improper use of the device.

Every user should know how to fix an electronic cigarette, since in most cases it can be done with his own hands. Often, the most common malfunctions are the flashing of a light bulb, as well as the production of a small amount of smoke during the smoking process, which at the same time gives off bitterness.

It will not be difficult to repair electronic cigarettes. If the battery light is blinking, the obvious solution to this problem is to charge the device. If during the vaping process less smoke is produced than it should be and at the same time it is bitter, it will be advisable to replace the atomizer, which is responsible for the formation of steam.

Based on statistics, we can say that battery breakdown as a result of a factory defect occurs in isolated cases. If an electronic cigarette breaks down, then this most likely happened due to improper use of its battery.

You should know if you fill an electronic cigarette with water - the battery will not work!

Often, novice vapers enter the query into search engines: "refueling an electronic cigarette with water." At first glance, the situation seems comical, but it has a place to be. If we exclude this ridiculous manipulation of this device, we can highlight the main causes of battery breakdowns.

As a result of the action of direct sunlight on the device, it overheats. There are many times when this smoking device is left in the heat in the car on the seat or under the windshield, or at home on the windowsill. Such cases are fraught with complete failure of the product battery. And then questions arise, why does the electronic cigarette not work?

This cause of problems is considered less common, but it also occurs. Negligent users thereby test the device for strength. In this case, the air flow sensors are not affected by air, but by liquid. Therefore, the battery is out of service and not charged.

Maintenance of an electronic cigarette eliminates the presence of systematic exposure to moisture, which can significantly shorten its life.

Very often, when using an electronic cigarette for the first time, a beginner smells burning.

Reasons for the sensation of a burning smell:

• Defective evaporator. It can be replaced under warranty.
• First puff taken too early. After connecting the evaporator to the cartridge, it is necessary to allow time for it to be saturated with liquid.

This is another problem in e-cigarette use that is associated with unpleasant emotions. To avoid it, you just need to develop the optimal suction power.

In the process of intensive air intake, a rather strong vacuum occurs, which in itself is fraught with the ingress of excess liquid from the cartridge onto the evaporator. As a result, the liquid does not have time to fully transform into steam and therefore it penetrates into the mouth.If the electronic cigarette is equipped with an automatic battery, you should not increase the suction power after the LED lights up, which gives a signal that the process of converting liquid into vapor has begun.

Let's take a look at the most common causes of problems with this device.

This is the most common problem in which an e-cigarette does not smoke properly. What to do if the electronic cigarette does not smoke?

This problem may be due to the fact that:

• The battery power is not enough for the correct operation of the atomizer. The reason may be the lack of charge in the battery, or poor contact of the clearomizer with the battery.
• There is no liquid in the electronic cigarette or it is not enough. For the device to work, you must refill the cartridge.
• There is liquid in the duct. You need to shake the device several times, like a thermometer.
• The puffs are too intense. In this case, less effort should be made, making a puff, the duration of which should be five seconds.
• The air passages are blocked. To eliminate this problem, it is necessary to clean the air intake duct.

This problem is most common among newbies. Although the e-whitefish stretches well, there is not enough smoke and it tastes bitter.

Presumable causes of device malfunction:

• The life of the atomizer has ended, which must be replaced with a new one.
• The battery voltage is too high. It is necessary to adjust the optimal values ​​of this parameter for the atomizer, as a result of which the bitterness will not be felt, and the smoking process will be comfortable.
• Interruptions in the operation of the battery, as a result of which the electronic cigarette stopped working in the correct mode. You need to send it in for repair or replace it with a new one.
• There is no liquid in the cartridge or there is not enough liquid. In this case, it is necessary to refill the cartridge.

If the indicator on the battery is on or blinking, the button on the battery may have fallen off. How to fix an electronic cigarette in this case? You need to lightly knock on it. If there are no positive changes, send it in for repair.

In the case of heating the clearomizer, it is necessary to ensure that the button on the battery, which itself is too sensitive, does not spontaneously turn on. If a clearomizer leak is found, its replacement is inevitable.

In this video, you will learn how you can fix an electronic cigarette with your own hands.

Electronic smoking devices only a few years ago appeared in the field of view of smokers. And in a very short time they gained a huge number of fans. These gadgets were created in China to help people who quit smoking. Indeed, although ES cannot be classified as completely safe devices, they have much less harm than ordinary smoking.

Such a device, like all electronic gadgets, is rather complicated. And often upsets its owner with a refusal to work. But, knowing what a smoking device consists of, you can understand and how to fix an electronic cigarette. In its overwhelming majority of cases, the ES can be damaged independently.

In the overwhelming majority of cases, malfunctions of an electronic cigarette are caused by improper and illiterate operation of the smoking device. Therefore, the first thing a novice vaper should do is to thoroughly study the technical characteristics and rules for using the purchased electronic cigarette..

In order to be able to independently cope with the repair of an e-sigerta, you should know its technical characteristics and constituent parts.

At its core, any electronic smoking device consists of three main components:

1. Mouthpiece. This element is made of plastic and performs the same function as a filter in a regular cigarette.
2. Clearomizer (atomizer). It includes three components: a body, an evaporator and a container with aroma liquid.
3. Accumulator (battery). The tasks of this tool include supplying the necessary energy to each of the sections of the power plant.

All components of an electronic cigarette are connected to each other in a common circuit, forming a reusable vaping device. If any element fails, after replacing it, the gadget will also begin to fully function further. In most cases, problems with the operation of the ES arise due to failures or breakdowns of the battery or atomizer.

This element is responsible for the timely production of the required steam. The atomizer includes the following items:

1. Wick.
2. Nichrome thread (it looks like a spiral).

The wick is located in a ceramic container equipped with special fasteners for the necessary contacts, as well as holes for air passage. On top, the wick is covered with a kind of bridge (this bridge provides the supply of aromatic liquid and protects the wick from various mechanical damage).

The bridge itself and the ceramic bowl are packed in a metallized sponge. The wick and the sponge itself have increased capillary capacity, they perfectly saturate the liquid and transfer it from the container. This action occurs due to the pressure drop due to the puff produced by the bather.

Steam production with ES starts immediately after the first puff.

When the puff is made, an electrical impulse is applied to the filament, which ensures that it is almost instantaneously heated to the maximum possible temperature. At the same time, the slurry in the container boils and is converted into steam. When vapor is combined with oxygen, it is drawn under pressure from the atomizer and into the vaping lungs.

Electronic cigarettes use several types of batteries. They can be:

1. Mechanical. The current in such devices is produced after pressing the power button. The bather must press it and hold it until the end of the full puff.
2. Automatic. These batteries are equipped with LEDs. The use of these batteries maximally creates a similarity with smoking ordinary cigarettes (an imitation of smoldering is created). Also, such devices are equipped with pressure sensors. With their help, the battery is automatically turned on as soon as the vaper takes a puff.

Experienced vapers do not advise you to repair the battery yourself. Battery may explode in untrained hands and cause personal injury. In this case, the repair of an electronic cigarette falls on the shoulders of experienced specialists.

If suddenly the smoking gadget stops turning on, this does not mean that the ES is of poor quality. A sensitive vaping device can quickly fail if it has been improperly used for a long time. It will be useful to study the most common reasons for abandoning the operation of an ES.

Unsatisfactory steam generation can be caused by some irregularities in the use of the device.... In particular, in the following cases:

1. There is not enough battery charge for full vaporization. What to do in this case? Carefully check the battery contact and recharge the smoking device.
2. The aromatherapy is over. This situation requires refilling the cartridge or installing a new block with aroma liquid.
3. The air duct is clogged with steaming liquid. Here you can try to shake the smoking device vigorously, as when shaking a regular thermometer.
4. Something is clogging the channel that allows air to pass through. In this case, in order to repair the vaporizer in an electronic cigarette, you should unscrew the atomizer, carefully inspect all the holes and clean the clogged ones.

If suddenly the steam has acquired an unpleasant bitter aftertaste, the reason can be looked for in the following:

1. The evaporator itself has broken. The defective part should be replaced with a new one.
2. The user has incorrectly set the voltage on the battery. To remedy this situation, you should have some experience. The voltage is set individually, by the test method. To correct the problem, set this measurement according to the battery capacity.
3. Decreased battery capacity. To bring the ES into working condition, you should check the contact between the atomizer and the battery. If no obvious breakdowns have been identified, it is better to send the battery to a repair shop or replace it.
4. Lack of aroma liquid. In this case, you just need to add aromazames to the desired level.

If suddenly your favorite electronic cigarette is stubborn and refused to come into working condition at all, some situations should be analyzed. Such a breakdown is most often caused by a breakdown of the battery itself. What to do in this case?

1. Check if the battery is working on another device. If it does not turn on, it is worth using the services of a workshop or replacing the battery with a new one.
2. When you try to turn on the ES, the power button starts flashing randomly. At the same time, the smoking device does not want to work. This could be due to a sticky button. Try very lightly to tap the device in this area. If this procedure does not help and the button continues to flash non-stop, the e-cigarette will have to be returned for repair.

The cigarette may stop turning on due to the leakage of the clearomizer (heating element). This often happens due to constant overheating of the device (this can happen if, for example, the user constantly carries the ES in his pocket)... In this case, you will have to replace the clearomizer with a new one.

It is worth double-checking the battery for the correct polarity. The ES stops working due to the fact that the polarity was not observed when the battery was installed. If such an event is not crowned with success, you will have to refer the gadget to the masters.

There are several explanations for this problem, which, by the way, occurs quite often. The reasons are such common situations as:

1. Insufficient contact between charger and battery. To rectify the situation, it is necessary to clean the connection contacts well.
2. Charging (or battery) breakdown. To confirm the guess, connect the battery to the working device. Then, if necessary, either repair the battery (by the hands of a specialist), or replace the battery with a new one.

This problem is caused by a discharge of the battery or its breakdown. First of all, it is worth double-checking the battery performance through an additional working device. Also, this problem can occur due to the lack of aromatherapy in the container. Steam generation may also be absent due to the breakdown of the clearomizer. If, after cleaning and checking it, the ES still does not produce steam, you will have to replace the clearomizer with a new one.

So, here are all the most common reasons why your favorite smoking device may stop working. It is worth studying all the tips and finding out what to do first when the electronic cigarette "strikes". And remember that any experience comes only from using the product. Newbies will always have questions.

Therefore, in order not to finally break the e-siegertu, before operating it, you should study the basis of the ES and its main components... As a last resort, it is better not to take risks and not try to disassemble the device yourself (in the absence of this experience). And ask for help from a specialist who will help to implement the necessary task at the proper level.

Like any technical device, the vape is designed for a limited period of operation. Every bather should know how to fix an electronic cigarette: the services of service centers and vape shops are expensive.

The charging battery is insulated under a metal case, but this does not protect the device from premature wear.

The batteries are designed for several thousand charge and discharge cycles. The main cause of breakdowns is user carelessness and non-observance of operating rules.

Professional e-cigarette repair detects the following types of problems:

• Overheating in the sun. The vape is adapted to high temperature exposure, but not protected from abnormal heat. In the scorching sun, the battery overheats, loses its charge, and may even explode. This also applies to the frequency of vaping: it is easy to overdo it with steam.
• Incorrect filling. Beginning bathers are ruined by curiosity. Many people wonder what will happen if water, beer, carbonated drink and other liquids are poured into the tank.

There is only one forecast - the burnout of the battery and the contacts responsible for the transmission of electric current.

The battery is wet. Vapes can be washed under cold water, but only partially and gently. If you drown your device in a puddle or sink, you can safely buy a new one. Repairing the gadget will cost more.

When the smell of burnt cotton and paper appears while vaping, and the liquid acquires a bitter taste, service is necessary. You can return the old taste with your own hands by replacing key components.

With prolonged and active vaping, the cotton wool burns out, and a plaque forms on the spiral. This deforms the coating and adds an unpleasant burning sensation to the steam. The spiral, like the wick, is changed manually on the atomizer. The main thing before doing is not to be mistaken with the material and winding option, which are designed for different voltages.

If the problem is not resolved, the e-cigarette vaporizer is out of order and needs to be replaced.

Correct cotton wool replacement is patience. Before the first puff, the wick is moistened with slurry and allowed to stand for 5-10 minutes. This will allow the cotton wool to soak and not burn out when energized.

E-cigarette malfunctions include the following malfunctions:

• Insufficient vaping power. If the electronic cigarette is used or actively used for a long time, the battery has probably completely exhausted its resource. Otherwise, there may be a lack of contact between the crylomizer and the battery. Dirt or debris may get on the contacts during disassembly.
• Liquid leaks. Depressurization occurs due to cracked glass or an unwashed tank. Before refueling, the contact surfaces of the glass and the body are thoroughly wiped, which eliminates leakage.
• Liquid in the duct. This is a common problem that occurs when refueling is careless. The usual shake of the vape will help in this.
• Vape doesn't work. If the tank is full, the clearomizer is working properly, and the battery is charged, but the device does not float, you should try to turn on the cigarette. On most, this requires pressing the button on the battery 5 times. In a similar way, the vape is turned off: this saves power, which is not wasted.
• The sensor flashes continuously. Probably there were some malfunctions during the charging process. This is a deformation of the socket, a faulty wire, contamination of the socket with spools or other debris from pockets and bags.

It is possible to determine the breakdown of the vape and repair it at home due to the bitterness in the smoke. This is a direct sign that something is wrong with the device. Whoever did it knows that in most cases changing the filter and spiral helps, but if this does not solve the problem, detailed diagnostics will be needed.

Not only the spiral, but also the evaporator deteriorates from high-temperature exposure.

For repairs, you will need a container with alcohol, where the disassembled atomizer is placed. This will free the part from the plaque that is likely to have led to the change in scent.