Geyser dion jsd 10 DIY repair

In detail: geyser dion jsd 10 do-it-yourself repair from a real master for the site my.housecope.com.

Optimal operation, economical use of resources, and durability of its operation depend on the correct setting of the gas water heater. Consider the adjustment of devices that have two toggle switches on the front panel - water and gas regulators, a semiautomatic device type.

Adjustment of any gas heater should start with water regulation. The nominal value of this parameter is indicated in the technical data sheet supplied with the device, usually 6, 10, 12 liters. In order to correctly adjust the device to the required value, you need to open a valve with hot water, it is important to observe the condition - only one valve should be opened if you have several points of water intake. Using the water toggle switch, set the value corresponding to the nominal value. After setting, the tap closes.

But one must take into account the fact that the head of the line flow is different for everyone and there are no general rules for setting.

Some experts advise, when the pressure of the system is weak, but the heater turns on, the handle of the water toggle switch should be set to maximum, and the gas switch should be gradually turned from minimum until the temperature that suits you is reached.

In order to regulate the gas supply to the device, you need to set the gas regulator knob on the front panel of the device to the minimum value. After connecting to the mains (for such models as Ariston and Electrolux), or installing batteries (Neva, Neva transit, Selena, Ladogaz, Oasis, Junkers, Bosch Therm, etc.), you need to open the gas valve. Then you need to open the hot water tap, the water heater will turn on and start heating.

Video (click to play).

The next step is to use a temperature measuring device to set the gas regulator so that the temperature difference at the inlet and outlet of the device corresponds to 25 degrees.

In this case, one should take into account the fact that heating does not occur immediately, you should wait a while. During the subsequent operation of the column, the temperature at the outlet of the device is changed using a hot water valve. Including a larger flow, it decreases, while a smaller one increases.

If, after the above actions, the set temperature is not satisfactory, changes must be made only with the help of a water toggle switch. It should be borne in mind that to increase the life of the column, it is not recommended to set the temperature above 50 degrees.

Instantaneous water heaters are quite inertial; when turned on, do not expect that a hot stream will immediately flow, you should wait a while.

Conversely, if you turn on hot water at the tap, it will become hot after a while.

If a short time passes between switching off - switching on, you must be careful, do not put your hands under the tap so as not to burn yourself, as after switching off a certain amount of liquid remains in the system. The inertia should be taken into account when adjusting the temperature in order to obtain the nominal difference at the inlet and outlet, there is no rush here, it is necessary to accurately select the appropriate position of the regulator, when the obtained result does not change for several minutes.

When the water heater operates on liquefied gas and the pressure does not correspond to the nominal one, it is adjusted in front of the nozzle. To do this, remove the casing, loosen the locking screw, connect the pressure gauge to the measuring pipe. Next, remove the seal from the adjusting screw, turn on the column, setting the regulator to maximum, open all hot water taps.The pressure is adjusted using the adjusting screw. This procedure should be performed by a specialist.

Top center knob for Winter - Summer mode

Some devices, such as Ariston, Oasis, Dion, Vector JSD20-W, etc. have a winter-summer mode, are equipped with a temperature corrector, on the Ariston column it is located below, on Dione, Oasis - on the front panel. Depending on the season, the knob is set to the plus position in winter and minus in summer. This option allows optimal use of resources.

Let us consider the method of setting up an automatic gas heater using the example of Ariston fast evo ont b 14, JUNKERS Bosch WR. The main difference is that only one control toggle switch is built into the control panel - regulation of water temperature and power, it is also an on / off control. Turning the knob clockwise increases the temperature, counterclockwise decreases.

When the device is turned on, self-diagnosis of the gas-water unit and other column systems occurs. In the event of a malfunction, the device is locked and the red LED lights up. Before switching on for the first time, it is necessary to adjust the gas inlet pressure. To do this, close the gas valve, loosen the screw in the gas block and insert the pressure gauge into the gas pressure take-off. Then open the gas valve, turn on the column by opening the water intake and make sure that the pressure corresponds to the indicated figure in the instructions.

To adjust the maximum and minimum values, you need to do all the above manipulations, then remove the batteries, put the microswitch in the off position, insert the batteries into the compartment. Open one hot water valve, turn on the microswitch, adjust the maximum pressure on the burner with the orange screw. Then turn it off again, adjust the minimum in the same way, turn the microswitch to the off position, if the indicator glows orange, then the settings are saved.

Setting up the Neva 4511 consists in regulating the flow rate of the jet flowing through the device using a water toggle switch. By setting it to a minimum, the consumption decreases, the device turns on at a value of at least 2.5 liters per minute.

Neva 4511 - control panel

When set to the maximum value, the flow increases, and the column turns on when the flow is at least 6 liters per minute. At intermediate positions, switching on occurs in the interval between these figures. If the line pressure is low, the manufacturer recommends setting the regulator to the minimum flow rate.

Water heater Termet 19 01 is equipped with water-gas fittings, which automatically maintains the set temperature at a constant level. This block has an automatic flow regulator with smooth regulation. When the knob is set all the way to the right, a small flow, 5.8 liters per minute, flows at the highest possible temperature.

If you need to reduce the flow, you need to screw on the tap. By setting the handle to the extreme left, a large flow flows, 11.5 liters per minute, with a reduced temperature. By setting the toggle switch to the middle position, the temperature changes in inverse proportion to the amount of water. If the flow control toggle switch is set arbitrarily, it can be changed with the gas control knob. If the Termet gas water heater does not ignite, we advise you to read the article at the link.

In addition, watch the video on setting up (adjusting) the Bosch gas column:

Quality control inspector
Posts: 772

CoVlig and EGS hit the spot. The diaphragm is 3/4 torn. It’s even amazing how it still worked.

Many thanks to all participants for their participation. The topic has been resolved.

The same trouble = ((Tell me where you can find the membrane!

Image - Gas water heater dion jsd 10 DIY repair

Consider one of the first and most common problems with gas columns, as a weak spark discharge or its absence.Such a malfunction of the gas water heater is quite common and it does not appear after a year or two after using the equipment, but after a few months.

Symptoms are generally as follows. Yesterday the gas water heater worked like a clock, but today it suddenly did not turn on. You close the hot tap, open it again - the column is working. Then, every day, more and more such manipulations have to be done (opening - closing the tap). And finally the moment came when it stopped working altogether. Then just call the master or do it yourself.

After removing the cover of the gas column and opening the tap, you see that there is no spark discharge. So why did the spark disappear, what is the malfunction?

1. A reason not related to the failure of any part.
1.1. Insufficient water pressure.

First, check the position of the temperature regulator knob, which is responsible for the water flow pressure at the inlet to the gas column. At low pressure, the column will not turn on. Turn the handle counterclockwise all the way to the far left, and then turn on the tap. If the column has started working, it is likely that there is a weak head in suitable pipes and the reason should not be looked for in the column.

1.2. Limescale build-up in the radiator.

When using hard, lime water, scale can form on the walls of the heat exchanger, which also affects the creation of the pressure required for the operation of the gas column. To remove scale, you will need to remove the heat exchanger, I note that you will have to disassemble almost the entire column. Prepare a 10% citric acid solution: stir 100 grams of lemon in one liter of warm water. Pour into the tubes of the heat exchanger and leave for 15 minutes. Drain the solution and rinse thoroughly with water. Cleaning is recommended at least once a year.

2. Souring and immobility of the stem.

Nitrous oxide can form on the stem located next to the microswitch. This, in turn, affects the mobility of the tongue and the closing-opening of the circuit contacts. To clean the stem, remove the microswitch and release the fixed tab.

3. Violation of the electrical circuit between the microswitch and the control unit.

Also, a malfunction of the gas column associated with the absence of a spark can be caused by a breakdown in the circuit between the switch and the control unit. To do this, check the terminals connecting them and the switch wires. Possible oxidation of contact points.

4. Faulty microswitch.

The switch is a consumable item, it breaks down rather quickly. Fortunately, its cost is not high, about 150 rubles. Replacing it is simple: disconnect the terminal and unscrew the two screws.

Malfunctions, which are less common, are the failure of the solenoid valve and the electronic control unit. We will consider them in a separate article.

If your automatic gas water heater does not turn on for some unknown reason, then this article is for you. Let us consider the main causes of malfunctions and possible ways to restore the equipment performance. Do-it-yourself gas water heater repair using Termaxi as an example. Before repair work, do not forget to turn off the cold water and gas supply taps to the column.

Like any automatic speaker, it runs on a pair of 1.5 Volt batteries each. If the gas water heater does not turn on, check the batteries. They could be discharged. Usually the batteries last for 6-12 months with intensive use. To do this, either replace the batteries with new ones or knock the shrunken ones against each other to seal them. Thus, the capacity is added. Install and check. If such a procedure did not bring results, then move on ...

First you need to remove the protective casing, which is attached with self-tapping screws. But first, we remove three regulators (temperature, water pressure and the number of working nozzles) by pulling them towards ourselves.

Since the wires are short, we take out the temperature display, the power button and the signal light.To do this, press down on the latches, and all parts will come out of the lock.

Inspect for mechanical damage to the wires. Then check the contact at the terminals of the battery compartment. To do this, remove the terminals and wipe the contacts with alcohol.

Open the hot water tap, if the gas water heater does not turn on, there may be several reasons.

The most common one is that the microswitch is out of order. It is he who is responsible for supplying power to the piezo element. The switch is fixed with two screws to the body of the water block.

It is easy to find out whether he is working or not. Open the hot water tap and press the microswitch foot, hold.

You should hear a click, as a result of which numbers appear on the temperature sensor, and the LED lights up. The nozzles will light up. If so, the switch is OK.

If this does not happen, you need to replace the switch. To do this, disconnect the connector and unscrew the 2 screws.

Read also: DIY 4-stroke scooter repair

Buy and install the same. If everything works, congratulations. DIY repair of the gas water heater is completed. If not, then remove the water block. Don't touch the gas one yet. In this Termaxi model, you need to unscrew 2 nuts and 2 screws.

In the Termaxi column, the water block is attached to the nozzles, so we also remove it. We disconnect the terminals that interfere and pull out the block. Attention! A spring is installed between the gas-water block. When removing the water block, do not lose it.

Check the condition of the stem. If it is clogged, flush it out. If you see mechanical damage, replace it. To do this, unscrew the 4 screws on the case.

There is a membrane, under it is a white elastic band. After removing it, unscrew the nut and remove the stem.

If there are deposits of salt or dirt on the membrane, clean them.

Upon examination of the membrane, damage was found in this case.

We install in place of the old one and assemble all the elements of the water block in the reverse order. We install it in the column, connect the connectors, check the functionality. The column lights up automatically when you open a hot water tap. The sensors are working. The gas water heater has been repaired!

It remains to put on the case and use.

31,060 total views, 26 views today

Despite the widest range of electrical heating appliances on the market, the gas water heater is still one of the most popular means of heating a house and providing it with hot water. This is a fairly economical option, since it allows you to simultaneously provide several drainage points in the house. Another advantage of gas water heaters can be considered the fact that they allow you to use hot water, practically unlimited, without any restrictions.

The geyser device looks like this.

Water flow regulator.
Chimney connection.
Power control.
Heat exchanger.
Water node.
Exhaust hood.
Switch.
Rear panel.
Diaphragm gas valve.
Ignition.
Gas unit.

Perhaps you will also be interested in an article about gas heating boilers, read more about them here

Two pipes are connected to the gas column. The first of them is designed for gas supply, the second - for cold water supply. In addition, a pair of burners is located at the bottom, one auxiliary and one main.

Important! The device of the gas column can be different, depending on the method of ignition - it (ignition) can be electronic, manual and using a piezoelectric element.

Such devices are designed to provide domestic and industrial facilities with hot water. The essence of their work is quite simple: cold water from the pipeline enters the column heat exchanger, where it is heated by burners (they are located under the heat exchanger). As you know, fire needs oxygen, therefore, so that the burners do not go out, the column is connected to the ventilation system of the house / apartment. The exhaust gas is eliminated by means of a special chimney, which is combined exclusively with a gas water heater.

Read about what to look for when choosing a water heater here

All the described types of columns function somewhat differently.

So, if the device is turned on manually, that is, the gas has to be ignited with matches, the burner will ignite from the fact that you turn the fuel supply valve. Although it is worth noting that such designs have become outdated a long time ago. Modern designs are equipped with either an electronic ignition or a piezoelectric element.

New models are activated at the touch of a button located on the front panel of the device. Piezo ignition creates a spark that ignites the pilot. In the future, everything happens in automatic mode - the tap opens, the column lights up, hot water begins to flow.

If the gas water heater is fired up electronically, then it is perhaps the most reliable and durable device. The system is turned on by means of a pair of batteries supplying the charge necessary for the formation of a spark. No buttons, no matches, the only thing you need to do to turn it on is to turn on the tap. In most cases, batteries last a very long time because the energy required to charge is minimal.

How to calculate gas consumption for heating a house - read here

The use of gas water heaters, however, like any other equipment, is accompanied by malfunctions, frequent or rare. At the same time, there are such malfunctions that can only be eliminated by specialists who have the necessary knowledge and admission for this. But there are those that can be easily eliminated with your own hands, so we will consider them.

Video - sensor malfunction

If the internal elements of the device are covered with soot or dirt, then this can also lead to failure. To solve this problem, you must remove the outer casing of the device, then clean each of the elements using a vacuum cleaner.

The next sign that the gas column has stopped working correctly may be the burner decay immediately after switching on. This happens due to the fact that the ventilation channel is clogged. Modern models of gas water heaters are equipped in such a case with special sensors that will inform the owner if there is no traction. After that, immediately turn off the gas supply. Next, the chimney should be checked. For this, the plug is dismantled and everything that has accumulated there is removed.

Important! You can check the draft of the chimney in the old "old-fashioned" way: bring a lighted match to it. If the fire on the match deflects in the direction of the chimney, then everything is in order with it. If this did not happen, then he needs a complete cleaning.

It is for this reason that the gas water heater should be inspected annually - this is the only way it will work correctly.

We also advise you to familiarize yourself with the basic requirements.

Modern gas water heaters are small and compact, so they can be placed in almost any convenient place. Their service life depends largely on how correctly they are installed and used in the future.

As you know, the device of the gas water heater is such that it has to work with a rather dangerous fuel. For this reason, during installation, make sure that, God forbid, there is no gas leak. If you cannot, for one reason or another, take care of this, or, even worse, cannot eliminate all the leaks, then further operation will turn into a dangerous activity, which sooner or later can lead to an explosion.

For this reason, it is categorically not recommended to install a gas water heater with your own hands. It is better to have professionals who have all the necessary skills, experience, and the appropriate equipment to do this.

So, for installation, you need the following tools:

dowels;
magnet and salt filter;
drill;
the required number of taps;
pipeline;
chimney corrugation;
gas pipe;
Mayevsky valve;
actually, the column itself.

The device is installed only in the kitchen and only on the wall, which is made of refractory material. The distance from the column to the wall surface should be at least 2 centimeters, if it turns out more, then this is even better. An asbestos sheet should also be laid here, which must have a minimum thickness of 0.3 centimeters.

Important! The apartment / house must have a chimney that will remove the products of gas combustion. It will consist not only of vertical, but also of horizontal sections, and on them it should go at a slope (approximately 0.2 centimeters per each running meter).

So that the pipeline does not accidentally burst, the gas column should be installed only when the water is completely drained from the system.

But editing, as we have already said, is not the most important thing. It is also important that the device is used correctly, for which certain operating rules must be followed. If you do not do this, then even the most expensive and high-quality model will soon break down. So we want to prevent this from happening. Firstly, we must not heat the water to a temperature that would exceed 60 degrees. The fact is that too high a temperature will lead to the formation of salt scale on the walls of the heat exchanger. The result is more frequent cleaning or, even worse, replacement of the heat exchanger.

In addition, we can damage the structure of the heat exchanger by using too hard water. To avoid this, the water should be softened using special means, or a special filter should be installed in the system.

Finally, it is not recommended to dismantle and clean the gas water heater with your own hands, because, as we have already said about this, professionals should deal with this procedure. Doing this with your own hands is extremely dangerous.

If you decide to purchase a geyser device for yourself, then pay attention, first of all, to the power of the model you have chosen. It should be enough to provide all your family members with hot water. The power of almost all modern models fits into the range from 3 to 60 kilowatts.

Important! The more powerful the gas water heater, the more water it will be able to heat up within a certain period of time.

The average “cell of society”, consisting of four people, needs a device with an average capacity of 16-24 kilowatts. It is more than enough for the dishes to be washed and everyone was able to take a shower. Even if the device has a low power of 16 kilowatts, it will be able to give 10 liters of hot water, which is enough to be able to wash and wash dishes at the same time.Of course, if you can, then buy a column with a capacity of 24 kilowatts, since it can provide 24 liters of heated water.

In addition, it is advisable to take into account the water temperature that a specific model can provide. For its designation, the Latin letters DT are used. For example, if water is already supplied to the heat exchanger at a temperature of 12 degrees, then it will heat up to 24 in it. therefore, it can be used even without preliminary dilution.

Today there are models that are capable of heating water even up to 50 degrees. Their power, as well as the cost, is an order of magnitude higher than conventional models. For this reason, if several plumbing elements are simultaneously connected to the system at once, then it is better to purchase a more powerful column so that it can provide them all with hot water at the same time.

Also, when buying a gas water heater, see if it is equipped with safety sensors. They are of the following types:

overheating;
damping of the burner;
burning;
reduced pressure;
temperature;
sudden interruption of water supply.

And remember: gas water heaters are only allowed to be installed in the kitchen! Installation of a gas water heater in the bathroom is prohibited! Unless she (the bathroom) meets all existing requirements.

Read also: DIY Fiolent router repair

So, we have analyzed what a gas water heater is, what are its features, what malfunctions may arise during operation and how to fix them later. We only note that such devices are extremely economical, especially in light of the ever-increasing utility rates. And the last thing: do not forget that prophylaxis of the column's performance should be carried out annually.

I wrapped the microswitch, which is under the flow sensor rod, in plastic wrap and now it is not afraid of leakage. And my leakage is so small that I couldn't see the drop nirazu, and the dampness still limescale the microswitch button, so that it did not come out of it and did not turn on the electronics. The microswitch can be easily removed from the bracket with two small screws.

I have a problem with a Selena gas water heater. As soon as the lid in the battery compartment is closed, the gas immediately ignites even when the water is closed. To heat the water, I first open the tap with water, then close the battery compartment lid. To turn off the gas in the column, I open the battery compartment cover. I called the master, changed the microswitch, but it did not help. The foreman cannot determine the breakdown. Who knows how to fix it, leave a comment, please.

tell me why there is a very weak water pressure in a turbocharged selenium gas column

after the column lights up, after a few seconds, the piezoelectric element is triggered and it goes out

Cac saedeniti provodchi
U menea sieli v siu provodcu crisi

amine column. lights up and the temperature rises to the maximum (70) and does not fall, the gas pressure is not regulated (gas at minimum). What could be? Thank you

put a new column RODA-20 A-6 started right away but after a minute it went out. after half a minute it caught fire by itself. and so until I typed in the bathroom, no matter what I did or did not regulate, it didn’t work. What could be? Thank you

column ross burns error her

As soon as the lid in the battery compartment is closed, the gas immediately ignites even when the water is closed. Tell me what to do, it's a piez.

what needs to be changed if the temperature is not regulated heats 27 no more.

Rod's gas water heater gets water on the batteries, what is the reason

what to do if you have to turn on the water both in the bathroom and in the kitchen so that the automatic column works is not very convenient

When water is supplied to the column, the lamp does not turn green. There is a spark that clicks, but the column does not ignite What could be the reason, not serviceability.

Any professional will tell you: "a gas water heater is a potentially dangerous equipment, so you can only entrust its maintenance and repair to a qualified specialist." However, the ability to understand which element is out of order and what it can lead to will definitely not hurt.

DIY geyser repair

In addition, you can deal with the elimination of some malfunctions that do not specifically affect gas equipment on your own. Read the description of typical breakdowns and recommendations for action in case of their detection.

Gas column device

Equipment can stop igniting for several reasons.

Gas column device

First of all, you must make sure that the igniter is working properly. If it does not light up, contact your gas service. A specialist will clean or replace the failed element. You cannot touch it yourself - it is dangerous.

Gas column device diagram

In modern units with electronic ignition, in the absence of ignition, gas ceases to be supplied - it is cut off by a valve. The user becomes aware of this through the corresponding indicator. In some situations, this problem can be solved by simply replacing the battery. Check this point in the instructions. If the manufacturer does not give such recommendations, it is better to immediately contact the gas service or a third-party repair service.

At one point, the column may not light up

Battery pack for igniting the column

The column will not light up if there is no ventilation draft. To check the level of traction, we bring a strip of paper to the ventilation grill. If the leaf does not change its position, or if it does not change it sufficiently, there are obvious problems with craving. In apartment buildings, utilities are engaged in cleaning ventilation wells - contact them. You can do this yourself with the help of a metal brush tied to a flexible wire (hose, etc.) of a suitable length, however, utilities usually do not approve of such unauthorized actions.

Burners often fail to fire due to diaphragm wear. This structural element deforms rather quickly, the burner starting mechanism becomes less sensitive and does not work when the water is turned on. Even in expensive heaters, membranes wear out in 5-8 years - unfortunately, nothing can be done about this.

Often burners do not fire due to diaphragm wear

To check, turn on the water to maximum. If the column turns on with a strong pressure, the problem is definitely in the membrane. Replacement of this element can be done on your own.

To do this, do the following:

unscrew the fastening nuts from the water unit (usually there are 2 of them);
unscrew the fastening screws, due to which the water unit is held in the gas unit (usually 3 screws);
detach the halves of the assembly and you will see a rubber membrane. If it is not flat but noticeably deformed, replace it. To do this, buy a similar product from a specialized store. If possible, give preference to a silicone membrane - it will last much longer than its simple rubber counterpart.

At the same stage, you can check the condition of the water intake filter. If it is clogged, clean it or replace it with a new one. To clean, simply unscrew the nut from the water supply side, take out the mesh and rinse it or replace it with a new one, depending on the condition.

If the heater turns on but goes out, the problem in most situations is the bimetallic temperature sensor needed to protect the equipment from overheating. Also, due to malfunctions of this element, the heater may not turn on at all.

This problem has 2 main development scenarios.

According to the first scenario, the burner lights up properly, the equipment functions for some time without any complaints, and then goes out and for some time does not show any signs of life - attempts to ignite the heater do not lead to anything. Usually, after 20-30 minutes, the equipment turns on again and history repeats itself. This is due to the excessive sensitivity of the sensor. As a rule, it is "congenital", i.e. this is a factory defect. It is extremely difficult to do something on your own. It is better to immediately contact the manufacturer's service for warranty repairs.
According to the second scenario, the column may turn off randomly, and sometimes not turn on at all. The reason usually lies in the wear of the insulating material of the conductor of the bimetallic sensor. There is a banal short circuit to the case, as a result of which the safety valve is triggered, and the column begins to behave abnormally.

Contact the service center for warranty repair

It makes no sense to turn to gas workers - the defect is clearly not a "gas" one. You also don't need to try to get rid of the breakdown yourself - you can only break the unit. Contact the service center for warranty repairs.

Water comes out with a weak pressure

Most often this happens due to clogging of the column heat exchanger with scale. Prolonged “idle” ignitions of the igniter are usually the cause of clogging. The device heats up the heat exchanger to a temperature sufficient to cause the remaining moisture to evaporate.

There is no water flow, scale is not washed out of the heat exchanger, until the next turn on of the equipment, it sets, as a result of which the column ceases to function normally. Cleaning the heat exchanger usually saves. In advanced cases, it has to be changed.

For replacement, it is better to immediately contact the professionals, but you can handle the cleaning on your own. Prepare screwdrivers, rubber hose, open-end wrenches and paranite gaskets. Purchase a descaling mixture from a hardware store. Usually it is called that - antiscale. A more budgetary option is rinsing with vinegar essence. Work in this order.

First step. Remove the fittings and the casing from the heater one after the other.

Second step. Turn off the inlet water and open a hot water tap, preferably as close as possible from the column.

Step three. Unscrew the water supply pipe from the heat exchanger and then move it to the side. After unscrewing the nut, the column heat exchanger will begin to release water. In total, about 1 liter of it will be drained.

Fourth step. Place a hose of a suitable diameter on the inlet of the heat exchanger and lift it just above the heater. Insert an ordinary funnel into the fixed hose and start slowly pouring in the prepared solution in a thin stream (instructions for preparation are given on the package). There is no need to rush. If you pour it too quickly, the antikipine will simply push it back out, and you are unlikely to like it.

Flushing the gas column heat exchanger

Leave the cleaning agent in the heat exchanger of the heater for 2-3 hours (usually the required time is indicated on the packaging).

Place a suitable container under the water tap and carefully re-feed the heater. Observe what comes out of the hose. Was there a lot of slurry coming out, and then the head returned to normal? Things are good. Otherwise, flushing will have to be repeated. Usually, the need for re-rinsing arises only when using vinegar essence. Anti-scale in most situations copes with the first time.

In such a situation, it is better to immediately contact a professional. He will perform the adjustment, which is extremely difficult to make without knowledge of the matter, and the column will start working normally.

You can find out the reasons for the appearance of such a malfunction for general development. There are two main reasons:

the gas comes under too much pressure. The heater ignites too actively, which leads to the breakdown of the fire;
the gas flow is too low. Air enters the heater burner, resulting in a microexplosion, which is interpreted by human hearing as cotton.

The column does not heat up the water sufficiently

This usually happens due to the insufficient power of the gas column. The user begins to demand more from the equipment than it can do.

There are two options for solving the problem:

we stop abusing and do not open hot taps at the same time at all points of the water intake;
buying a more powerful speaker.

Also, inadequate heating of the liquid can occur due to the clogging of the burner. Look at the color of the fire. Under normal conditions, it is bluish. If the flame turns yellow, contact the gas industry. Such repairs can only be entrusted to a professional, tk. this is already a "gas" breakdown.

The problem is more than serious. Don't even think about any hand-made repairs. Turn off the heater, turn off the gas cock, ensure that there is adequate ventilation at all times, and call the gas service immediately. The arriving team will assess the problem and take appropriate action.

Now you know the main malfunctions of the gas column, and you know how to behave when they appear. The main thing is to remember about safety. There is no need to try to fix breakdowns for which you do not have enough qualifications - this can lead to irreparable consequences.

Video (click to play).