Homelite f3045 DIY repair

In detail: homelite f3045 do-it-yourself repair from a real master for the site my.housecope.com.

On compression - answered in a personal, and the resource.
Is the model 3045? Then - 300 - 500 hours (unofficial data, no official). If you're lucky with the fuel, of course.

Homelite F3045 has been in operation for 5 years. Magnetto flew off once. Now the gearbox is jammed, but you can't really make it out, can someone tell me where to find a new one?

Type in the search engine "Homelite", one of the first links will get you to a decent service - check there. The gearbox, it seems, is only changing the assembly.

This is the question. After repairing the clutch under warranty last year, the saw was not used. This year I decided to mow the lawn and started it with difficulty. Symptoms 1. Gasoline is not pumped into the transparent suction cap. When trying to pump up gasoline, characteristic zips are heard, as if the air is sucking. 2. in a horizontal position it does not start, for that in a vertical position it grasps, it puffs for 20 seconds and then starts to work normally, including in an inclined position. However, if it is transferred to a horizontal position, it immediately stalls. I went to the service. I told him. such an uncle from the village through the lip with a cigarette - you ruined her nah. Or change the carburetor or piston. I do not believe in the bright feelings of this MASTER. If faced, what it can be and how to treat it. Thank you.

Have a question! Homelite is broken. There is no time for repairs, and no money either. Found in Elitech T1000B store. It looks like nothing, the manufacturer is China. The people who used it. Feedback is urgently needed! What a beast it is. Thanks in advance!

Olegych Found a service, bought a spare part all the way, mow on!

Video (click to play).

Good time to the masters.
Problem with F3045. Purchased for school
recently took it away from the dismissed caretaker.
Shabby, of course. She worked for about an hour,
then it stopped starting. There was no spark, it turns out.
Well, I twisted it, moved the high-voltage wire carefully.
Look - it's started up! I gave it to the worker, in half an hour he comes,
will not start again. I checked the spark right away - not yet.
Everything rang out with the tester - the reel, the wires, the switch - everything is OK.
Looks like you need to get to the magneto.
Did anyone have such a problem? What do you advise?

I changed the magneto for 3 years. Changes are elementary, the main thing is not to rip the flywheel key. After repair for 2 years, the flight is normal.

Dimru, thanks for the answer.
Only - to change? Can't repair the magneto?

Yes, the magneto there is not repairable if the reason is correctly established. During the repair, I took a picture of it, if I find a photo, I will send it.

A photo would be very desirable.
I have no idea what kind of design.
It's just that I'm a radio technician by profession, I'm used to repairing electric radio myself.
Some doubts about the reason. There was a spark, disappeared, then reappeared.
Alternatively, the magneto (electronic circuit?) Is in order, somewhere the contact disappears from vibration.

mastertx wrote:
There was a spark, disappeared, then reappeared.
Alternatively, the magneto (electronic circuit?) Is in order, somewhere the contact disappears from vibration.

Just one of the manifestations of some kind of malfunction of the ignition module.
Quite often they bring the product: “There is no spark. "Take it, start it. The next day again: “no spark”. We take - we start. I drove a little, died out - there is no spark.
We change the module - everything works.
So - it is possible that the ignition will go awry. But it is necessary to check for the presence of a spark on a candle that is known to be in good working order.

It is necessary to check the attachment of the wire to the coil itself. In some models, a small self-tapping screw sticks out of the coil, and the wire is wound around it. From vibration, the connection is weakened and the spark disappears, it is treated like this: a piece of about 5 mm is cut off from the wire with a sharp knife and rewound on the magneto.The same thing should be checked from the side of the cap. If the wire is glued into the magneto, then only a replacement.

Hooray! Working! Replaced the magneto.
Olegych and SERVER77 - thanks for your help.
This thread helped a lot.
Dimru - special thanks!

A tenacious unit, it still works! I’m already looking at something new, but this one, if only henna. It is operated all summer in harsh conditions, it also winters in the country. Starts with a floor butt! But I regret not having bought a cultivator attachment for it. Now it is very rare. there is one answer to all my inquiries - no delivery expected.

Dimru wrote:
A tenacious unit, it still works! ...

I fully subscribe! I have a spit soon for 7 years.

However, the question is where it is possible (if possible) to get the screws for attaching the muffler, I have (as in the anecdote about balls.) one screw was lost somewhere, and the second one broke, but there are pieces of the complete one. The screw, of course, with its own head, hardened (in appearance), you can't remove the washer, you can't buy it anyhow or anywhere. And yet - is it somehow possible?

The youngest daughter has already given Champion LM-5131 (otherwise it’s hard for dad to mow.), But the pedantry remained - Homelite mowed so that it would be nice to look at it, and LM-5131 and tall grass is bad enough and near the house - change houses - fence - trees - leaves clumps of bushes.
Yes, in fact, and without pedantry after LM-5131, it is not at all superfluous to bypass the fence inside the plots and on the street you can’t drive it along the gutter along the fence near the road of the partnership.

Someone thread will advise something on the way.

You need to look in specialized stores. On my chainsaw, the tire fastening pin turned off, I found nothing in a gasoline tool repair shop, but here in St. Petersburg.

Well, yes - after all, we are talking about the engine and it makes sense to look for it not by the spit, but by the engine. After all, Homelite also produces chainsaws and, it is possible, with this engine. Thanks!
In parallel - everyone reading this thread - if someone has this old scythe (or chainsaw) that is out of order completely, do not look at these cogs? You are welcome!

Good day. Guys, please tell me what could be. Scythe HOMELITEF 3045, has ceased to maintain momentum. flushed blew out the carburetor, replaced the spark plug. Gasoline and oil are appropriate. it starts up only in a cold plant, as soon as I switch it, it stalls. may even jerk the khan a little more. there is a nuance: if I lift the mowing element up, it works normally, reacts to the gas key, keeps the speed, idle is normal. I don’t know what else could be. Thanks in advance

but only at point 4, the problem arises - what kind of wondrous device and where to get it. you can't fold it by hand!

A similar question, googol is silent.
The link itself says 3 / 8-24.

although I seem to have found it. Universal clutch remover for motor vehicles.
The question is now different.
Where to look for a CPG on a hummer mtk31, can anyone come across?

To read the instructions, select the file in the list that you want to download, click on the “Download” button and you will be redirected to the page where you will need to enter the code from the picture. If the answer is correct, a button will appear in place of the picture to receive the file.

If there is a “View” button in the field with the file, it means that you can view the instruction online without having to download it to your computer.

If your material is not complete or you need additional information on this device, for example, a driver, additional files such as firmware or firmware, then you can ask a question to the moderators and members of our community, who will try to promptly respond to your question.

You can also view the instructions on your Android device.

Good trimmer, worked for 4 years. Recently, I have mowed a lot, incl. and a dense weed, worked for 8-10 hours with breaks for a smoke break, refueling, a short rest.Lightweight, good start-up. It is very convenient to transport, the collapsible shaft. Disadvantages: - the line on the reel often has to be corrected (confused) if a large weed or overgrowth of cherries, plums, etc. comes across. - it is necessary to wear clothes with long sleeves (when the right hand touches the engine, just below the elbow, it gets burned, if mowed for a long time - to a blister); - the gasket on the tank lid crawled out after 2 weeks and gasoline began to ooze, I had to cut it out of fluoroplastic myself; - strong vibration, hands get tired after an hour or two of work; - increased sound of work, during work you can not hear what people are saying nearby. But in general, she worked wonderfully well (they say 4 years is a lot). Something broke between the engine and the shaft (a characteristic crunch, after which it stalled) when trying to mow a large thick growth of milkweed in the garden with a knife in the height of a person with a stem thickness of 1-2 cm (maybe he overdid it with the load himself) with a knife. Lawn and grass mows exclusively! I haven't repaired it yet - I don't know what exactly broke down and where it can be done.

The trimer has been working since 2009. started up without problems after storage. In 2-17, the piston got stuck in thick grass due to old gasoline mixture and work at low revs in cramped conditions. I did not work very much during the season a couple of times a year, mowing grass in a ditch and on a site of 12 acres. It is my fault that I lost my guard. the model is outdated but I really want to restore it. I will try

Homelite F 3040, worked flawlessly for 7 years! does not grasp. gasoline, candle, spark: everything is normal! what could be?

Write review Homelite F 3040
Describe how satisfied or dissatisfied you are with your purchase Homelite F 3040

Good day! There was a problem - I can't find a line threading unit (reel) on sale. Tell me where you can buy.

Feeling that the revolutions gives more than the current Echo. Perfectly cuts, cuts, starts.

The factory, by the way, is convenient at that time. pumped up gasoline, started, pressed the gas and work. The lever is immediately transferred to hot start.

normal model, experience has shown that it is best to trim with line. How many different lines I didn’t buy, or very thin, or very thick, but the power is quite enough. Chopping raspberries is not suitable, as it becomes life-threatening. Raspberries are better with a shovel or secateurs.

I thought about using it as a gas engine for a boat, but then I bought a motor.

There is not much to think about here, and after weighing all the pros and cons, you will find the answer yourself!
Very often on all possible summer cottage forums one can find the following topics: "which trimmer is better", "than me to mow the grass at home" ...
The first thing you need to answer to yourself is what result do we want to get from this device? And also it is realistic to assess the scale and conditions of work on the site with it.

Here it is necessary to step back a little and again say a few words about the choice between an electric and a benzo instrument. In favor of the first are factors such as lower cost compared to the second, as well as ease of use. Alas, there are also disadvantages, and in my opinion they are very serious:

not being able to work after rain or when there is a lot of dew - this is really life-threatening! (someone will say bullshit, we put good machines and RCDs and no problem! Their right ...) the laws of physics have not yet been canceled.
Oddly enough, the dependence on electricity in the literal and figurative sense of the word, someone does not have it at all, someone has frequent interruptions, the third simply does not have the opportunity to unwind 100 m of wire - and why is that?
electric motors, although they now have rather good protection against overheating, are clearly more vulnerable than internal combustion engines when working with frequent load changes ...

The main disadvantages of gasoline engines in this case include the following:

much more difficult to operate than an electric motor.Only a person who has at least basic knowledge in this matter can configure it for stable operation and reliable start-up, and often this becomes a big obstacle when choosing this type of technology.
much noisier in operation compared to the former.
petrol! Not only does his presence just shock someone, it still needs to be diluted in a certain proportion with oil. Moreover, it is a big problem for some (and maybe many) to precisely measure 20 mg of oil per liter of gasoline (the figure may differ depending on the types of engines and other reasons!), Although this problem can be easily solved by buying a disposable syringe at any pharmacy !
well, and probably all the nuances associated with the peculiarity of the operation of a gasoline engine can be attributed here.

If, after weighing all the pros and cons, your choice still fell on the benzotrimmer, the following material is for you.

Buying such an assistant for the household, I fired up as soon as they began to appear from others. Of course, who at least once in his life mowed with an ordinary scythe, without even looking, sees the difference in the work of both tools! She is impressive ..
This is not to say that it is very easy to mow with a trimmer, modern models, especially professional ones, can weigh even more than 10 kg and despite the well-thought-out "harness", amateur models for a modern city person accustomed to soft office chairs have a significant weight. With no habit, the back and arms can often hurt after just an hour of work, which passes with time and the acquisition of skill. And someone even begins to catch a kind of thrill from the process.

Here are just a few words about one of their representatives.

On the advice of a friend, a Homelite F3055 gas meter was purchased in 2006. Initially, the task was to purchase a budget but rather powerful and versatile machine! To which, in principle, this model corresponds more fully.
This model has a classic arrangement of nodes for all models of this type of equipment.
The first thing that caught my eye was a spring-loaded suspension and, as my neighbor said, a "shovel", not a large plastic plate that protects a person's leg or side, probably not so much from injuries as from "crushing" this part of the body.

First start! On the store mix, the trimmer started up with 3 jerks even without "suction", great.
Large colorful box, set of interchangeable attachments: steel knife and trimmer head with line were originally installed.
Talking about the design and beauty of the instrument in this case is useless and pointless.

First impressions:
The braid is well weighted, this becomes clear as soon as it is hung on the strap on your shoulder. There is only one strap, but since the weight is not large, only about 5 kg, it is enough and you do not experience any inconvenience. The only thing that needs to be done right away is to correctly adjust the suspension height - the trimmer should hang on the shoulder strap and not on your hands! It is useless to give any recommendation here, look for the position that is most convenient for you, since all this can be done without any devices, only with bare hands.
The very first hours of operation showed insufficient protection of the casing when working with the line, be prepared to be all in the grass. Especially if you mow something with soft, fleshy stems. To the word, the instruction prescribes to have proper work clothes, as well as GOGGLES. Believe they are needed!

Working with a typewriter, as I said above, is convenient. The wide-set and well-rubberized handles provide a comfortable grip, which, in terms of vibrations, are present. At different engine speed ranges, their values sometimes change significantly ...
That, in other matters, does not prevent you from doing this pleasant business for an hour or more.
It seems to me reasonable to work with a metal knife in two cases:

I will talk about the fishing line a little later, but for example, having practiced a little, I can easily mow (or rather saw through) with a fishing line even burdocks 2 cm thick! You just need to remember one trick - the fishing line mows mostly with its ends.

The plastic protective body kit and, at the same time, the cylinder blowing system is painted in black and red. The engine qualifies as semi-professional.
Despite all this, according to the manufacturer, the engine has a chrome-plated cylinder, which must have a positive effect on the reliability of the entire unit. The third season of the trimmer has gone, no complaints about the piston operation.!
Fuel consumption does not increase! It still lasts for an hour of continuous work. I confess I had to mow against the instructions and for 2 hours at 30 degrees of heat, the engine continued to work confidently and without failures.
The braid starts up well, somewhere even excellent, as cold (in warm weather, even without the use of the patented "cold start" system, and hot. Although it is not difficult to "fill" a hot engine, it takes some skill. enough for stable engine operation further.

Fuel :
Fuel is a separate topic of conversation ...
The trimmer loves high-quality gasoline (among other things, like any engine), you may well not start it on last year's gasoline, therefore I do not advise buying it much, as well as following the path of those who like to breed 5 or even 10 liters of gasoline (and then store it in plastic non-sealed canisters from which all light fractions evaporate in a couple of weeks) and scold the instrument from scratch when it refuses to start.
The debt brought by the neighbor in the form of 5 liters of the mixture, after running out of a full tank, forced me to completely disassemble the carburetor and blow it all over (and more than once!), Only all these measures made it possible to return the trimmer to work. A neighbor, by the way, completely replaced the carburetor on his "Calm".
CONCLUSION: pour only high-quality fuel.

By the end of the second season of worries, the gasket under the cylinder began to leak. (but most likely the lack of tightening of the screws securing the cylinder to the crankcase ...
The tank is located at the bottom under the engine and literally is the support for the entire unit. The plastic from which it is made is durable, multiple falls on it are almost painless for the latter. Alas, the tank itself is attached to three points, two of which are located on the crankcase in the form of two small tides entering through a rubber gasket into a recess on the tank body. On the other hand, it is pressed in the same way by a part of the crankcase cover, and when it falls, this ill-fated cover folds back!
The entire engine block is attached to the bar with two large plastic halves (jaws) that surround it, and tightened with two screws. If they are poorly tightened, the engine may start to "go" back along the boom. It seems like nothing terrible, if not one thing: the longitudinal play of the drive cable of the working element increases. And if from the side of the clutch the area of contact with the unit is quite large and it has a place to “walk”, then at the working head its four-sided end enters the groove under it by only 10 mm. Small area of force transfer + longitudinal play of the cable, they led to the rolling of the edges! Its end has become almost round - the result is the lack of transmission of torque from the engine. It is treated by simply turning the cable 180 g.

And that's all ... I have not yet been able to find any more serious shortcomings.

Small improvements:

The double handle (popularly called horns) is attached to the bar through a plastic block, which, in combination with one hand-tightened fastening bolt (for quick dismantling and adjustment), does not provide proper fixation. The solution to the problem was a piece of sandpaper bent in half, abrasive outward as a gasket.
The place where the bar rests on the leg is trimmed with paralon, in order to preserve it, you can immediately wrap it with something like electrical tape, otherwise all this will quickly turn into rags.
I also had to turn the upper spring loop by 90 grams. For which the suspension clings, otherwise it would be torn off all the time from its seat.

You will have to get used to cleaning your tool after each work (it is more about working with a fishing line), wet grass together with dust turns into real "cement" when it dries, which can then be cleaned only by soaking it with water. The plastic protection can be washed safely.
The big plus of the suspension device is the system of quick uncoupling of the entire unit from the strap. Many smile saying that it is bliss. But everyone who fell while mowing (and no one is immune from this.) Will appreciate this system, when by pulling the flag you can completely unfasten. Calmly get up and dust off to continue working. And it's always nice to just throw off the scythe at a halt.
In general, the ergonomics of the braid is at a very good level, as it is customary to say everything in it is in place.

Origin: I don’t presume to answer whose production this product is, it is brightly flaunting on the engine protective casing - it was made in France (in principle, the purchase price at that time in 2006 corresponded to European origin, the quality was the same), nevertheless, on the lower carburetor cover the inscription "made in china" flaunts. Reviews of today's HOMELITE owners and their price point more to a purely Chinese origin of modern samples.
Despite all this, I am completely satisfied with the machine! 3 years of almost perfect service, on half a hectare of land + neighboring gardens and overgrown borders. Practically weekly work during the period from May to October, and given the class of go, allows us to say with confidence that it can be successfully used in your household. For example, with the neighboring "Calm" bought a year earlier, there were much more problems ...

If you are already so impatient or needy, like me and you have to adjust the carburetor, here are some numbers and theory:

The large screw influencing the damper drive is “idle gas”; on trimmers with automatic clutch it is precisely this screw that regulates the engine speed so that the working element does not rotate.
The other two are jeklers, depleting or enriching the mixture.

All the above numbers and positions may not coincide with the factory settings of the engine and are based only on personal impressions and the theory of adjusting carburetor two-stroke engines! And they are not a guide to action.

A little about the line (trimmer line):
There is a lot of controversy about what is generally better than a knife or a fishing line ?!
It seems to me that it makes sense to use a knife only in extreme cases. There is no way to use a cord.
For the rest, of course, the fishing line is more preferable: its performance is much higher than that of a steel knife, the convenience of work is several times, and a light trimmer reel less damages the scythe drive. Believe me, the cost of the fishing line for the season is worth it, whoever has mowed it at least once will never use a knife unnecessarily.

This trimmer can use any line with a thickness of 1 to 2 mm (I can safely use 2.5 and 2.7 mm). It should be noted at once that the consumption of a thick cord at times! Less than thin, and a difference of only 0.5 mm can be significant. The use of a cord up to 1.5 mm is advisable only for mowing lawns with fine and soft grass. Thin line mows the small grass, in contrast to the thick one, which tears it into rags.
A cord of 2 mm can be attributed to universal, it mows both the lawn and small weeds in the form of wormwood, quinoa and small burdocks equally well.
But in order to cope with small shoots of shrubs (young raspberries, rose hips), as well as with plants with a strong fibrous stem, such as potato tops, an adult stiff burdock needs a more durable (often labeled "heavy-duty") trimmer cord with a thickness from 2.5 mm.
I was satisfied with the abundance of husqvarna products on our market.
On average, it takes me about 20 - 25 m of cord per season, and I mow a lot!

Most of the sold cord is color-coded, here are the approximate matches

Go to page of 22

Documents that we receive from a manufacturer of a Homelite F3040 can be divided into several groups.These are in particular:
- Homelite technical drawings
- F3040 manuals
- product passports Homelite
- information brochures
- energy labels Homelite F3040
All of them are important, but we will find the most important information from the point of view of the user in the user manual for Homelite F3040.

The group of documents, defined as operating instructions, is also divided into more detailed types such as: Homelite F3040 installation instructions, operating instructions, short instructions or Homelite F3040 user manuals. Depending on your needs, you need to search for the required document. On our website you can view the most popular instructions for using the product Homelite F3040.

A complete manual for the device Homelite F3040, how should it look like?
A manual, also referred to as a user manual, or simply “instructions” is a technical document designed to assist in the use Homelite F3040 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Homelite F3040.

A complete Homelite manual, should contain several basic components. Some of them are less important, such as: cover / title page or author's pages. However, the rest should give us information that is important from the user's point of view.

1. Preface and tips on how to use the manual Homelite F3040 - At the beginning of each manual you should find directions on how to use the book. This should contain information regarding the location of the Homelite F3040 content, the FAQ and the most common problems - that is, the places that users most often look for in each user manual.
2. Content - an index of all tips for the Homelite F3040 found in this document
3. Tips for using the basic functions of your Homelite F3040 - which should make it easier for us to take the first steps when using Homelite F3040
4. Trouble - a systematized series of actions that will help us diagnose and in the future the order of solving the most important problems of Homelite F3040
5. FAQ - most frequently asked questions
6. Contact details Information on where to look for the contact details of the manufacturer / service center for Homelite F3040 in a given country if you cannot solve the problem yourself.

Use the form below

If using the instructions found you did not solve your problem with Homelite F3040, ask a question by filling out the following form. If any of the users had a similar problem with Homelite F3040, most likely he will want to share a method for solving it.

I am looking for the order of assembling the Homelite F - 3040 trimmer carburetor, the order of installing the gaskets and adjusting after the complete disassembly of the carburetor. One of the gaskets is not sure about the installation after assembling the carburetor when starting the plug dry air filter wet Trimmer will not start if there is a spark on the new plug

Download instruction Homelite F 3040 on Yandex disk to my email ""

Jammed piston with a radiator. How to stir it up for disassembly and revision of the condition and possible repair. How to get to the trigger. Although it works, the clutch adapter cannot be easily removed. The fasteners are not visible. The puller can damage the protection. And how to do it right: The clutch-coupled piston rotates without problems. the second piston does not rotate And then how to set the pairing of both pistons. Thanks if I get an answer. I worked the trimmer for five seasons without any problems. Maybe that's all? It doesn't seem so

Before buying Homelite F 3045, I want to read reviews of the owners about it, those people who have already bought and use the product for some time. On this page you can read the opinions of buyers about the product. After reading the reviews, study the characteristics, see the prices, check out the video reviews, select the online store and buy.If you are the owner of this device, then leave your feedback on the owners forum page. Average price: 2023 rub.

Advantages: Quite light, I start with a half-kick (subtlety, in cold weather you need to hold it in a warm room, in the cold it is capricious). Good power, easy to mow under bushes. I like the U-shaped handle - it looks like a regular braid, it's easy to get used to. Convenient line feed - hitting the head on the ground in the work - the line unrolled.

Disadvantages: After 3 years of operation, the line outlet hole in the trimmer head has developed.

Commentary: I have been using the braid for 3 years. In my feminine opinion - a cool braid - light in weight and in work. Productivity - 25 acres of garden and lawns per day with breaks and distractions. Koshu herself. Those. maintenance is minimal - fill in the petrol-oil mixture and sweep it with a broom after work. The line is easily refueled after you understand which tail is in which direction. It is better to mow not overgrown grass. The lower parts of the trees and bushes need to be protected with something (I attach cut-off plastic bottles to the seedlings from below), otherwise the bark can be damaged. Last summer, the muffler screw was unscrewed and sweated, I had to select a new one. There were no more breakdowns.

Advantages: Koshu oblique fifth year. There are no problems, I bought it on the advice of a neighbor - he has been mowing for nine years (plots of 12 acres each) are working for wear and tear. So that there are no problems with the engine, pour a little more oil into gasoline and you will be happy! Power is enough to mow grass and small bushes up to 10mm thick. Oblique is 100 percent satisfied, I only pour gasoline and my air filter, it's worth its money.

Disadvantages: Sometimes it starts up the second time, but always and in any weather! A little noisy and vibration is felt, hands tremble after four hours of use. The metal bushings of the line feed hole on the reel are worn out, but it is not critical, it does not affect the work)

Comment: A good braid for five thousand rubles, made of high quality, collapsible (easy to transport). Experience of use confirmed by two trimmers! Treat with care, do not accelerate at idle and no load, cut with the line at the maximum length and it will serve you for many years! Good luck to everyone and less grass, because in the country you need to rest and not work.

Advantages: Lightweight, convenient, foldable for transportation in a car, very convenient, starts with 3 jerks. For 3 years of operation, the metal bushings in the head were worn out, turned 180 degrees with a screwdriver and mow on.

Disadvantages: The head is such that the long grass was constantly reeling, solved the problem by making a casing from a tin can to cover the rotating rotor and the tall grass mows with a bang

Commentary: excellent trimmer for the price

Advantages: Compact scythe, collapsible bar, very convenient for transportation. I have used the scythe for 12 years. plot of 18 acres. with a knife mowed wilds. 20mm without problems. convenient handle. if you need to mow around or near a bush, the handle does not interfere. the blade of a high-quality knife does not deform upon impact

Disadvantages: I replaced my native fuel filter with a calm one. I had to clean the carburetor.

Commentary: In 12 years the scythe has justified itself twice changed the reel, the holes for the line exit were wiped, as I understood from the asterisk, the knife hit the stones many times during use, the deformation was not triggered; that the analogue is no longer sold, it seems like a patriot has now turned a knife on the first stone into Mr.

Advantages: Price, ease of use, light weight, ease of changing the cutting element.

Disadvantages: The vibration is very strong on the throttle handle, after two weeks of dense operation it stopped responding to the shutdown button, but then everything went abruptly and now everything is normal.

Why can't a person find the videos they want on Youtube? The thing is that a person cannot come up with something new and look for it. He was out of fantasy. He has already watched a lot of various channels, and he no longer wants to watch anything (from what he watched earlier), but what to do in this situation?
In order to find a Youtube video that suits your needs, it is imperative to keep searching. The harder your search is, the better your search result will be.
Remember that you only need to find a few channels (interesting), and you can watch them for a whole week or even a month. Therefore, in the absence of imagination and unwillingness to search, you can ask your friends and acquaintances what they are looking at on Youtube. Perhaps they will suggest original vloggers that they like. You, too, may like them, and you will become their subscriber!

Online mp3 cutting is convenient
and a simple service to help you
create a musical ringtone yourself.

YouTube video converter Our online video
the converter allows you to download videos from
YouTube website in webm, mp4, 3gpp, flv, mp3 formats.

These are radio stations to choose from by country, style
and quality. Radio stations all over the world
over 1000 popular radio stations.

Live broadcast from webcams is made
absolutely free in real
time - broadcast online.

Our Online Television is more than 300 popular
TV channels to choose from, by country
and genres. Broadcasting of TV channels is free.

A great opportunity to start a new relationship
with a continuation in real life. Random video
chat (chat roulette), the audience is people from all over the world.

These are brushcutters with forced motors (motors with increased power-to-weight ratio)

AVAILABLE AND RELIABLE COMBAT (DOMESTIC) MOTOR BUCKERS RED STAR

Petrol cutters RED ZVEZDA have gained well-deserved popularity. The next step in the direction of replacing (“politely putting out the door”) euro - and American imports is the RED ZVEZDA line of brushcutters. They are similar to Homelite, Ryobi, MTD brushcutters (many parts are interchangeable, parts for the RED STAR are half the price). Without reinventing the wheel, we will help you choose the right brushcutter. Knowing about the former popularity of Homelite petrol cutters in Russia, we, the manufacturer of motor cutters in the Moscow region, have adopted the main features of American mowers and support the Russian brand.

The first and most important feature "Fighting benzokos" Is light weight (or more precisely, weight / power ratio). Thanks to this, you can work quickly and efficiently. Motocars for your garden and summer cottages KRASNAYA ZVEZDA use extremely reliable and very successful (there are numerous reviews) forced motor with a volume of 25 cm3 and 30 cm3. It is known that the quality of human life is primarily the quality of the water he drinks and the air he breathes. People have understood this long ago and therefore are fighting for the ecological cleanliness of brushcutters according to the so-called EURO-3 standard. The toxicity of the exhaust gases has been significantly reduced (by 75%). Now you can work with a scythe for hours without fear of breathing. The new two-stroke motor the RED ZVEZDA brushcutter engine is an elegant development, using elements of the theory of gas dynamics and chemical kinetics. Bypass ports, piston forcing ribs, cylinder and muffler cooling geometry.

Video (click to play).

The models are easy to maintain: foam air filters are used, which are easy to clean and do not require oiling, transparent fuel tanks to control fuel consumption. Bodywork, brushcutter parts - gearbox, knife, bar and drive, guard on the gearbox, control knob - this is the language that the motor speaks with the user and with nature. Here everything is according to the principle - nothing more. Simple and reliable. Torsion fields, aerodynamic clearance, keyless connections, molybdenum and lithium lubricants are inside. For those who use it - everything is simple, clear, proven by experience and years of operation in all regions of Russia, from the Arctic to the South of Dagestan.

Rate the article:

Grade 3.2 who voted: 85