Hotpoint ariston arsl 100 DIY repair

Details: hotpoint ariston arsl 100 DIY repair from a real master for the site my.housecope.com.

We continue the cycle of articles on repairing washers with our own hands!
The Hotpoint Ariston range is very diverse and includes two dozen washing machines.

As an example: family 105 - arsl, arusl, arsf, armxxl, aqsf, then ariston 5050, 109 and 129.
Let's decipher ARSL 105 (A - ariston, R - assembly Russia, S - depth 40 cm, L - no display, 10 spin speed 1000 rpm, 5 - noise level).

To be honest, everything is confusing and hard to make out.
And the search for a malfunction during repair is similar in all instances.

There are cars where there is a liquid crystal screen, then in case of a breakdown there is an error code on it.
And if it is not there, then - we look at the blinking indicators of the front control panel!

To determine the error code, it is necessary to summarize the blinking LEDs according to the figure.

Ariston models HotPoint (1 pic) and AVL, AVSL (2 pic)

Well, now the fun part - DIY Hotpoint Ariston washing machine error codes!

F01 - the signal is lost between the control board and the motor.

Make sure the mains voltage is stable. Must be at least 210 volts.

The motor control circuit is a rather capricious component of the washing machine mechanism. It would be nice to check the contacts yourself for corrosion and moisture. It is advisable to check every connection from the control board to the motor. It is possible that a problem may arise even from a detached motor pad.

We measure the control voltages on the motor block with a tester.

Thyristor may be defective Check motor terminals.

Brush motor control board:

Video (click to play).

Control board with asynchronous 3-phase motor:

1 NTC thermistor. 2 Condenser. 3 Choke. 4 Diode bridge. 5 Power supply unit. 6 processor motor control. (Q1-Q6) - IGBT transistors.

F02 - no signal from the engine tachogenerator and the electronic module.

We also check the engine block and the module connector.

We make sure that the tachogenerator is working properly:

The resistance of the contact group in a quiescent state should be about 70 ohms. Without removing the test leads from the coil lead terminals, rotate the motor shaft. Resistance, in this case, should change. If this happens, then the tachogenerator is working properly.

F03 - breakage of the temperature sensor (thermistor), short circuit of the wash heating element relay.

The sensor itself rarely fails. Usually there is no signal from the board (pins of the temperature sensor connector)

F05 - the drain pump or pressure switch (level sensor) does not work.

By 80 percent, a blockage (filter, drain hose) or a pump is to blame.

We clean the filter by removing the front panel with a flat screwdriver and screw it around:

The pump impeller must be clean and free of debris:

We put the washing machine on its side and separate the pipe from the tank and pump:

If error F05 pops up again - the reason is in the electrics, namely why the pumping pump does not work?

We take the multimeter in our hands and, starting the drain program, measure the voltage at the pump terminals. It should be 220 volts.

His presence tells us about the replacement of the pump.

F06 - in Diagnostic models, indicates disabled buttons.

A rare mistake, and here everything is clear.

F07, F08 - the heating element is not in the water, does not work (burnt out or open).

Make sure there is water in the tank by looking into the drum. Further, after removing the back wall, check the heating element with a tester:

F04, F08 - pressure switch (water level switch).

Signal from connector J3.

Check the condition of the level sensor:

- contacts-2-4 are closed - level "EMPTY TANK"
- contacts 2-3 are closed - level "FULL TANK"
- contacts 2-1 closed - “OVERFLOW” level (not less than half the glass level of the loading door.

Remove the top cover by unscrewing the two screws at the back. This sensor is on the top:

Why is it needed?

For adjusting the water level in the tank: low, medium and high. Also provided with protection against tank overflow.

How to check?
Just blow into it. You should hear clicks. There may be three. Depends on the water levels provided by the program: economical, delicate, half load.

F09 the memory card of the electronic board is faulty.

F10 - the water intake time has been exceeded.

The filler pipe from the detergent drawer to the tank may be clogged, the water inlet valve is not working properly.

Also check the level sensor (see above).

F11 there is a problem with the drain pump.

The resistance of the pump winding should be about 170 ohms - measure it with a tester.
Follow the instructions for error F05

F12 - there is no signal between the control board and the program selector.

Carry out an external examination of the board for damage to the elements.

If no burned-out units were detected, diagnostics of the control module and its flashing are required.

F13, F14, F15 the drying element is faulty (washers with a drying function).

F16 - the breakdown is associated with blocking the drum (top loading machines).

F17 - hatch lock lock problem.

No power supply to the door lock - ring the contacts.

Module diagnostics required.

H20 - error no water supply.

It often happens that this is a clogged inlet filter, and there is no water permeability due to dirt.

We unscrew the inlet hose, clean the filter mesh at the inlet

In addition, check the water pressure at the inlet of the solenoid valve and its serviceability.

More common Hotpoint Ariston faults:

The washing program does not start, the door lock lamp blinks frequently:

Throws an error and drains the water.

We change the engine brushes.
We put the washing machine on its side so that we have free access from below.
Caution: The detergent dispenser must be at the bottom to avoid water ingress on the control board!

Disconnect the power connectors and unscrew the engine from the tank.

Do not forget to clean the manifold between the motor sipes as well. They are covered with an abundant layer of graphite dust. It needs to be removed. The most convenient way to do this is with a vacuum cleaner. The engine manifold should be cleaned with the abrasive part of a dishwashing sponge and visually inspected for wear.

We put the engine in place, plug in the connectors, but do not put on the drive belt. The no-load lapping procedure must be followed. To do this, we start the spin mode at the minimum available speed, visually and audibly controlling the operation of the engine. It should be flat and free from excessive sparking. Then we put on the belt, and once again we start the spin at minimum speed with an empty drum.

No water is supplied, the drum does not spin (the engine does not run):

Read also: DIY Aveo gearbox repair

The door is locked, the display shows the code F-01, error H20

The drainage system must be properly organized; the tip of the hose must be at a height of 60 to 100 cm.

In addition, a jet gap must be ensured when draining in order to avoid water being sucked back into the CM.

A detailed diagram of a tank with bearings and a drum:

001 - screw m8x23 002 - bearing 25 x52 x 15
003 - screw m8x22
004 - bearing 20x47x14 6204 skf
004 - bearing 6206-2z 005 - sealing ring 008 - fastening screw + washer
009 - tank cross member for 46 liters, 010 - upper counterweight 11 kg 011 - suspension spring bracket
012 - tank spring l = 181 mm 013 - sight glass gasket 016 - front counterweight
017 - a clamp for a hose from the side 019 - a clamp for a tube of a pressure switch
021 - tank holder 46 l with hole. n1040325
024 - shock absorber 80n hole 8.15 025 - drum flange 46 HP
029 - crosspiece with seals 030 - pulley d = 210 mm h = 20 mm
031 - elastic belt l = 1046-1051

The practice of recent years has shown that you can repair the Ariston washing machine with your own hands.

Each master who is engaged in the repair of complex household appliances undergoes a special training course.

This course examines the functional and schematic diagram of the Hotpoint Ariston washing machine.

Nowadays, this machine is very popular with consumers. This is due to the multifunctionality of the washing machine and ease of use.

Practically in every large city and even in rural areas there are service centers for the maintenance and repair of these units.

Hotpoint Ariston washing machines appeared on the home appliance market many years ago. Today, analysts have nearly eighty models that successfully fulfill their functions.

Each new model carries an additional feature that makes the washing process easier or better.

Among the advantages of the models of this brand, the following should be noted:

high quality washing;
noiselessness;
operational safety;
ergonomic design.

With ease of operation and high reliability, repairing Ariston machines requires a consistent and accurate approach.

When the Hotpoint Ariston washing machine installed in the bathroom performs its functions properly, very often no maintenance actions are performed.

And only when there are some malfunctions, attention is paid to the state of the machine. In order to determine the nature of the breakdown, you need to imagine the general scheme of the unit's operation.

If you draw a simplified diagram of a washing machine, then it will consist of the following components and assemblies:

tubular electric heating element - heating element;
Electrical engine;
drain pump - pump;
water inlet valve;
bearings and oil seals;
sensors and timers.

This is an incomplete list of devices that make up the Hotpoint Ariston washing machine.

However, it gives an idea of how the machine works and what connections exist between individual devices and mechanisms.

Initially, any model is designed in such a way as to economically use water and electricity. Particular attention is paid to the consumption rates of detergents.

All these resources are combined in such proportions to provide a gentle wash cycle. Different fabrics are washed in different ways.

Washing modes are set using special sensors and regulating devices.

Self-repair of the washing machine must begin with an assessment of the malfunction that has occurred.

When the machine works normally in all modes, but the quality of the wash decreases, and the spinning is practically not performed, you need to inspect the drain hose.

The used water enters the hose through the outlet filter. The video shows the procedure for removing and cleaning the filter. This is a standard operation.

In such a situation, it is necessary to clean not only the filter, but also all the pipes adjacent to it.Even when large items such as coins, buttons and key rings do not enter the filter, dirt will accumulate over time.If cleaning the outlet filter and hose at the Hotpoint Ariston washing machine did not bring any result, then you have to remove and repair the drain pump. It is easy to remove it with your own hands.As a rule, threads are wound around the impeller, which are separated from the laundry during washing. This leads to a decrease in the number of revolutions and even deformation of the impeller.As a result, the impeller starts to touch the casing. And this crackle is perceived as a signal of a serious breakdown.In this case, in order to eliminate the defect that has arisen, the impeller can be carefully cut with a knife or scissors literally by 1-2 mm.The regular operation of the Hotpoint Ariston washing machine largely depends on the quality of the water.Despite the fact that tap water is purified and softened, a certain concentration of salts remains in it. When heated, these salts settle on the heating element in the form of scale.Over time, the heating element loses its original characteristics.The water heats up more slowly and the quality of the wash decreases.To correct this situation, you need to either replace the heating element, or clean it from scale.In the video, you can see the sequence of actions when replacing the electric heating element.Repairs are easy to do on your own.

Washing machine Hotpoint Ariston of the Italian manufacturer is reliable and of high quality. But some parts of the washing machine sometimes become unusable.

You can, of course, send it to a service center for repair, but in order to save money and with skillful hands and a smart head, you can independently repair an electromechanical household appliance.

Do-it-yourself repair of the Ariston washing machine is easy to do. Follow our instructions for restoring the washing machine, and your assistant will serve you for many years.

In the Ariston electromechanical device, the main reason for the incorrect operation of the machine is blockages.
In addition, the heating element becomes unusable due to the appearance of limescale on the heating element due to hard water.
The pump can also be faulty due to its long operation.
Sometimes the filler valve fails due to damage to the rubber gasket.
In rare cases, bearings and seals have to be changed.
Electronics almost never breaks down, but we will still touch on the issue of replacing the control unit a little.

It is easy to remove the blockage with your own hands. You need to check the drain filter, which is located on the lower right under the panel.

After cleaning the filter, you will eliminate the cause of the malfunction of the washing machine. Less commonly, the drain pipe is clogged because it is thick.

There may be a blockage in the pump, but rarely, because there is an additional filter in front of it.

The drain hose will only become clogged if you have not installed it correctly.

Check the drain, there may be a blockage in it too. Disassemble the unit, pull out the branch pipe by loosening the clamps, flush it. Pull out the pump by unscrewing the fasteners and disconnecting the sensors.

Signs of a pump breakdown:

The drain pump hums, but the water does not drain.
The machine may stop when the system is running.
Water flows out slowly.

Repair of the pump of the Ariston washing machine must be done as follows:

If the filler valve is broken in Ariston, then water constantly flows into the washer, even when it is not working, it is disconnected from the network.

To check the filler valve, you need to unscrew the fasteners and remove the top cover. The valve is located where the drain hose connects to the body of the electromechanical unit.

Check the gaskets first. If they have not lost their performance, measure the resistance of the valve. Put the probes on the contacts of the filler valve and check the resistance, whether it is optimal (from 30 to 50 ohms).

If it is less or more than the set value, it means that the water intake valve is not working. To replace it, you need to unscrew the old valve from the body and screw in a new one. Be sure to connect the sensors.

If the heating element is faulty, then it is imperative to replace it. Its breakdown is indicated by the fact that the water does not heat up or washing in all programs takes place in cold water. Sometimes the machine gives an error and stops.

To replace the heating element, the rear wall must be removed. There are two contacts under the tank with a fastener in the middle. This is ten. Measure the resistance of the heating element with a multimeter.

If the resistance is within the normal range, then there is no need to change the heating element - it is serviceable. To remove the heating element, you need to unscrew the screw in the middle and pull it towards you with swinging movements.

The water may not heat up also due to the fragile connection of the wires to the heating element, which arises from the strong vibration of the washing machine. Water heating may also be absent if the temperature sensor is faulty.

Take a tester or multimeter and check the resistance of the sensor when cold and hot. If the resistance is the same, then it is broken, requires replacement. The resistance should be different.

The high-quality and durable material from which the drum of household appliances is made also becomes unusable, because solid foreign objects get into it, which can damage the unit, forming cracks on it.

The plastic rib inside the drum can deform. Remove the drum to replace it.

To remove the drum yourself, you need the following set of tools:

a set of screwdrivers, especially a Phillips screwdriver and a slotted nozzle are needed;
screwdriver;
pliers;
hammer;
hexagons of different sizes.

Use a Phillips screwdriver to remove the bolts from the back, front, and top walls, and then remove the panels themselves.

Dismantle the powder container. Use a slotted screwdriver to remove the module. It is not necessary to unscrew the control unit to the end, the main thing is that it does not interfere with the removal of the drum.

Remove the hatch cuff, pull out the lower bar by unscrewing the screws. It is necessary to dismantle electronics, shock absorbers and other parts from the loading tank.

Remove the drum from the device and disassemble it. Remove the screws holding the two sides of the drum. Pry the oil seals with a screwdriver and remove them.

The bearing in the drum can break and wear. It needs to be replaced.You only need to buy a bearing of the corresponding brand in a specialized store or order it on the official website of the Ariston washing machine, possibly purchase it in an equipment repair workshop.

Use a metal rod and a hammer to knock out the bearings. If they are defective, replace them. If the drum is deformed, replace it with a new one.

Reassemble. If the malfunction is in the plastic rib, then you do not need to disassemble the tank. The washer door is removed. A metal rod is taken, the diameter of which is smaller than the holes in the plastic rib of the drum.

The rod is inserted into one of the holes on the rib, the latch is opened with it, the plastic part is removed. A new plastic rib is put in its place. Slide along the groove with the plastic rib until the latch enters the hole and closes.

The LED indicators on the control panel receive a signal from the faulty unit. An error code is reflected on the display, indicating a breakdown of some element.In the Ariston Margarita 2000 washing machine, in case of a malfunction, the power button starts blinking and the handle of the command device is constantly turning. The flashing pattern is different depending on the fault. The codes can be found in the instructions for the machine. Image - Hotpoint ariston arsl 100 DIY repair

The control unit may fail due to mechanical damage, water ingress on it. Do-it-yourself repair of the control module can be done on your own only when a small part has failed or you need to replace the board completely.

In other cases, contact the service. Professionals will help you repair, rewire complex electronic circuits.

It is necessary to unscrew the screws on the board or remove the plates with a wrench, depending on its brand. Remove the control unit by replacing it with a new one. Screw in the fasteners carefully so as not to damage any part.

The price of the repair depends on its complexity. If the device does not drain the water, then the cost of restoration work ranges from 1200 to 3000 rubles.

Repair of the control module costs more than 3,500 rubles. The rattle and clatter of a typewriter can be corrected at a service center in Moscow for a price of 3,000 to 5,000 rubles.

Today we have shared with you our knowledge on how to repair the Ariston washing machine with our own hands.

We hope that you will succeed and self-repair will cost you inexpensively, you will not have to pay for disassembling and assembling washing equipment, for restoration work with the help of specialists.

Models of Hotpoint and Margarita washing machines from the Italian manufacturer Ariston are rightfully considered one of the most reliable, ergonomic and high-quality among numerous competitors. However, even with them, unforeseen failures sometimes occur, which can be easily eliminated with your own hands.

Before you start repairing the machine, you first need to figure out which malfunctions most often lead to a malfunction of the unit and determine the code of possible malfunctions.

The stability of the Ariston machines, first of all, depends on correct operation... If there are certain problems, then you can try to fix them on your own, without resorting to the help of a specialist. But for this you need to figure out what can most often cause malfunctions.

Perhaps one of the most common reasons causing problems in the operation of the machine is blockages that impede the passage of water during the process of draining it, which, in turn, leads to the inability of the washing machine to readjust to the rinsing mode. Typical signs of this problem are idle operation, loud noise and the inability to pass water through the hose (or very poor water permeability). As for the places of blockage, then they can be concentrated:

in the drain hose itself, and in most cases blockages occur if it is incorrectly installed;
often blockages form in the drain filter itself;
blockages may occur in the branch pipe, which is located between the drain filter and the tank;
and also in the pump, although this is an extremely rare practice.

In order to correct the situation and eliminate the malfunction, it is enough to clean the machine from blockages in accessible places (pump, hose, drain pump or branch pipe).

The second problem that can be encountered in the operation of Ariston machines is lack of water heating during erasing... Often, in such a situation, the washer can be shocked due to dysfunction of the insulation of the heating element.

The main reason that is the provocateur of such a malfunction is extremely hard water, as a result of which scale forms. The repair consists in replacing the damaged electric heater (heating element). To do this, unscrew the rear panel of the machine, since it is behind it that the fastener of the broken electric heater is located. First, you should disconnect all contacts and unscrew the fastening screw, then carefully pull out the broken heating element and replace the part with a new one. That's it, the malfunction has been eliminated, and the machine should heat the water as before.

The most difficult problem is the breakage or partial wear of the bearing or oil seal at Ariston. Fortunately, in practice, it is extremely rare.

To understand that machine malfunctions are bearing failure result, it is enough to pay attention to the following signs:

during the operation of the unit, all moving elements of the washer begin to emit characteristic sounds during spinning;
in this case, the shaft begins to come into contact with the sleeve;
vibrations are possible.

It must be said right away that this problem should be eliminated promptly, since otherwise you can simply break the machine. The only difficulty is that the repair will require almost complete disassembly of the car. Therefore, if you are not confident in your actions, it is best to entrust this process to a professional.

In this case, most likely, there is a malfunction associated with socket or power cable... To check the operation of the outlet, it is enough to try turning on another electrical appliance. If everything is in order with the outlet, then you need to check the wire itself. To do this, you must disconnect it from the outlet and try to "ring" with a special tester.

In the event that the electrical wire is normal, then, most likely, the problem is hidden directly in the power supply unit of the machine. This is a rather complex problem, so only an experienced professional can solve it.

It is interesting! How to open the washing machine yourself if it is locked

Another problem that can cause the machine to stop working is no drum rotation... There are several reasons that can cause such a situation: engine breakdown; wiring problems; collection in operation of the control panel or filter clogging. However, the most common cause is belt wear or excessive stretching. In this case, you need to replace it - there should not be any special problems with self-replacement.

If the reason is different, then it is best to call a professional to your home to identify the cause of the breakdown of the machine.

An equally common problem that users of Ariston Hotpoint or Margarita machines may encounter is a malfunction that occurs directly in the control unit... The main reason for this problem is the malfunction of our power grids, which is extremely problematic to deal with on our own.

In this case, the problem is easier to prevent than to fix. Therefore, before starting to operate a washing machine, in particular, Ariston, it is best to put special protective equipment, which help to protect the washing machine from power surges and other similar failures. This approach will be much more efficient and economical than replacing an entire control unit.

Operational problems can also arise during loose or broken mechanical fastenerswith which the machine is equipped. Most often, this is expressed in the weakening of the machine's hatch fixation. The problem has the following symptoms: loud noise during the operation of the washing machine and characteristic vibrations. To get rid of this, it is enough to tighten or completely replace the fasteners with new ones.

It should be noted that such models of Ariston washing machines as Margarita 2000, Hotpoint, Avsl 109 and others have unique self-diagnosis function... The bottom line is that the system independently detects a malfunction and shows on the display or by flashing indicators, its specific code. Having an idea of which code number the unit shows, you can independently identify the problem and fix it.

It is interesting! Reasons that the washing machine does not draw water

Having an idea of what most often failures can occur in Ariston typewriters, you can try repair the unit yourself... However, you should start it only if you are confident in your actions. If there is no experience in such things, it is best to entrust the repair of the washing machine to a specialist.

Washing machines Ariston from the Italian manufacturer can be called "a model of reliability and quality", but they sometimes require attention. In some cases, repair of Ariston washing machines can be done by hand, and a specialist needs to be involved only in the most difficult cases.

Within the framework of this article, we will analyze the frequent malfunctions of automatic washing machines of the Hotpoint Ariston brand, study the "symptoms" of such breakdowns and decide how to properly make an independent repair.

The vast majority of breakdowns of Ariston washing machines are associated with their operation. This is recognized by the masters of service centers for the repair of washing machines. Sometimes we are talking about frankly incorrect operation, the user regularly makes gross mistakes, which lead to breakdown. But most often, the cause of the breakdown is the operating conditions, which the user either did not know about, or guessed, but did nothing. A striking example is hard water, which can completely disable the "home helper"!

So, what are the most common breakdowns on Hotpoint Ariston washing machines? We decided to compile a kind of breakdown frequency rating. When compiling the rating, we rely on statistical data provided by leading service centers for the repair of washing machines.

Blockages. The blockages themselves can hardly be considered breakdowns; rather, this is the cause of various breakdowns. Nevertheless, it is with blockages that craftsmen have to deal with most often, and it is strong blockages that most often paralyze the operation of various Hotpoint Ariston washing machines.
A heating element. Teng is in second place in our rating. Despite the fact that the heating element itself is of high quality, low-quality hard water does its job. Over time, the scale layer destroys even the best part and has to be replaced.
Water pump. In third place is the drain pump or pump. This part fails quite rarely and in most cases the reason is wear from prolonged operation.
Filling valve. Even less often, the filler valve fails. More precisely, not even the valve itself, but a rubber gasket. Over time, rubber dubs and begins to let water through, and this causes a malfunction.The gasket itself costs a penny, but the services of a master to replace this gasket are by no means cheap.
Bearings and seals. In fifth place are the failures of bearings and oil seals. On Hotpoint Ariston washing machines, this is a rarity, but if such a breakdown appears, you cannot continue to operate the machine.

Important! The electrics and electronics of the Hotpoint Ariston washing machine are deliberately not included in the rating, since it rarely breaks down.

If you have problems with blockages on the Hotpoint Ariston washing machine, do not rush to call the master, everything can be repaired quickly, with your own hands. How do you know that you are dealing with a blockage? The main sign of a blockage in the drain system is the idle operation of the drain pump, that is, it hums, but the water does not leave the tank. Usually, this trouble manifests itself after the end of the wash, the machine cannot drain the waste water to start rinsing and freezes, or it drains the water too slowly.

A strong blockage can be found in several places:

in the drain pipe, between the tank and the drain filter - this happens less often, since the pipe is quite thick;
in the drain filter - there is a blockage most often;
in the pump - in Ariston washing machines, blockages in the pump are rare, since an additional filter is installed in front of the drain pump;
in the drain hose - blockages rarely occur, mainly in cases where the hose was installed incorrectly.

How to quickly remove a blockage? First of all, you need to check and clean the easily accessible places of the washing machine, where a blockage could occur. First, we unscrew the drain filter, which is located on the Ariston machines at the bottom right under the narrow panel. Place a cloth on the filter before unscrewing it as water will drip off. Remove all debris from the filter and then screw it back on.

Next, it is important to check the drain hose and drain. In a number of situations, a banal blockage in the drain pipe can force the user to contact a machine repair specialist, when it was more correct to contact a plumber. And if everything is in perfect order, then you will need to disassemble the machine, clean the pipes and the pump. To remove the pipe, you will need to loosen two clamps, and to remove the pump, you will need to disconnect it from the sensors and unscrew the two fasteners.

If any malfunction occurs, the Hotpoint Ariston "washing machine" gives an error with a specific code displayed on the screen. It is very important to recognize the error codes of Ariston washing machines correctly, because this is a direct clue indicating the cause of the breakdown.

A broken filler valve "symptomatically" is quite difficult to confuse with other breakdowns of the Hotpoint Ariston washing machine. When the filling valve stops blocking the water, water begins to flow into the washing machine tank by gravity, even if the “home assistant” is turned off from the network.

If you hear the characteristic murmur of water being poured and drained from the tank when the machine is turned off, be sure this is a valve.

To check the filler valve, remove the top cover of the Hotpoint Ariston by unscrewing the two fasteners. The valve is located at the junction of the inlet hose with the machine body. First of all, we check the gaskets, if they are intact, then you need to measure the resistance of the device, and for this you will have to use a multimeter. We install the probes on the contacts of the filler valve and check. The meter should read approximately 30 to 50 ohms.

A defective filling valve should be replaced with a similar one; self-repair is not possible. The replacement itself is done very quickly, we unscrew the old valve from the body and screw in a new one, not forgetting to connect the sensors. It is worse if the pump is out of order, because it is a rather expensive part.

A faulty pump gives itself out during washing, when the machine should drain the water, but it does not, while the pump either does not make any sounds at all, or it hums, but the murmur of the drained water is not audible.

Note! Strictly speaking, these symptoms are superficial and they may indicate other problems (for example, with electronics), but this should give you the idea to check your pump first.

In the Hotpoint Ariston washing machine, it is at the bottom and can be reached through the bottom. It is better to check and replace the drain pump by a specialist, but you can do everything yourself, the main thing is to thoroughly study the progress of work.

The heating element is an important part of the washing machine, which is responsible for the temperature of the water in the tub, and therefore for the quality of the wash. If the heating element is faulty, the wash either does not start at all, and the system generates an error, or the wash is performed in cold water. Both should prompt you to check and replace the heating element in the Hotpoint Ariston washing machine.

Checking the heating element of the Ariston washing machine is not difficult at all. It is necessary to unfold the machine, at the bottom of the rear wall there is a service hatch, which is attached to the clips and several screws. We unscrew the self-tapping screws, and wring out the clamps with a screwdriver, after which the cover will be removed. Behind the lid, under the tank, you will see two large contacts with the fastener in the middle - this is the heating element. We unscrew the screw, and then we begin to pull the ten on ourselves, pulling it out with swaying movements.

Note! Before pulling out the heating element, it is a good idea to measure the resistance with a multimeter, perhaps the device is working properly and does not need to be touched.

As we have already noted, bearing and oil seal failures are the most rare malfunctions of Ariston washing machines. However, if this happens, then urgent action is needed. It is not difficult to recognize such a breakdown. When the bearing is destroyed, the moving elements begin to emit unpleasant sounds, the shaft begins to rub against the bushing, which leads to a depletion. If you do not take any measures and continue washing, this can lead to the fact that the drum begins to play and damage the tank.

To prevent your favorite washing machine from ending up in a landfill, you need to contact a specialist when such sounds appear, or try to change the bearings yourself. If you are determined to do the work yourself, study the information offered on our website. Otherwise, with such a complex repair, it is not surprising to make serious mistakes. The main difficulty is that in order to get to the bearings, you need to disassemble the entire washing machine, along with the tank.

In addition, it will be necessary to correctly remove the old bearings without damaging the bushing, and then install the new ones correctly so that repeated repairs are not required. Without the proper skill, not many can do self-repair, so before starting work, think about delegating it to a specialist.

In conclusion, we note that the repair of malfunctions of Ariston machines can theoretically be done by hand, especially if you have the time and patience. But all the same, in order to avoid mistakes and unnecessary expenses, it is better to turn to a specialist, because “a miser pays twice”!

Video (click to play).