Hotpoint ariston arsl 100 DIY repair

Details: hotpoint ariston arsl 100 do-it-yourself repair from a real master for the site my.housecope.com.

We continue the series of articles on repairing washing machines with our own hands!
The Hotpoint Ariston range is very diverse and includes two dozen washing machines.

As an example: family 105 - arsl, arusl, arsf, armxxl, aqsf, then ariston 5050, 109 and 129.
Let's decipher ARSL 105 (A - ariston, R - assembly Russia, S - depth 40 cm, L - no display, 10 spin speed 1000 rpm, 5 - noise level).

To be honest, everything is confusing and hard to parse.
And troubleshooting during repairs is similar in all instances.

There are machines where there is a liquid crystal screen, then in the event of a breakdown, an error code is on it.
And if not, then - look at the flashing indicators of the front control panel!

To determine the error code, sum the blinking LEDs according to the figure.

Ariston models HotPoint (1 pic) and AVL, AVSL (2 pics)

Well, now the most interesting thing is Hotpoint Ariston washing machine error codes with do-it-yourself elimination!

F01 - Lost signal between control board and motor.

Make sure that the mains voltage is stable. It must be at least 210 Volts.

The motor control circuit is a rather capricious component of the washing machine mechanism. It would be nice to independently check the contacts for corrosion and the presence of moisture. It is advisable to check every connection from the control board to the motor. It is possible that the problem may arise even from a detached motor block.

With a tester, we measure the control voltages on the motor block.

Perhaps the thyristor has become unusable. Check the motor terminals.

Control board with commutator motor:

Video (click to play).

Control board with asynchronous 3-phase motor:

1 NTC thermistor . 2 Capacitor. 3 Throttle. 4 Diode bridge. 5 Power supply. 6 engine control processor. (Q1-Q6) - IGBT transistors.

F02 - no signal from the engine tachogenerator and the electronic module.

We also check the engine block and the module connector.

We make sure that the tachogenerator is working:

The resistance of the contact group in a quiet state should be about 70 ohms. Without removing the probes from the terminals of the coil leads, rotate the motor shaft. The resistance must change. If this happens, then the tachogenerator is working.

F03 - breakage of the temperature sensor (thermistor), closing of the washing heater relay.

The sensor itself rarely fails. Usually there is no signal from the board (temperature sensor connector contacts)

F05 - the drain pump or pressure switch (level sensor) does not work.

80 percent is to blame for a blockage (filter, drain hose) or a pump.

We clean the filter by removing the front panel with a flat screwdriver and wrap it around:

The pump impeller must be clean and free of debris:

We put the washing machine on its side and separate the pipe from the tank and pump:

If error F05 pops up again - the reason is in the electrician, namely why is the pumping pump not working?

We take the multimeter in our hands and by running the drain program we measure the voltage at the pump terminals. It should be equal to 220 volts.

His presence tells us about the replacement of the pump.

F06 - in Diagnostic models, indicates non-working buttons.

A rare mistake, and here everything is clear.

F07, F08 - the heating element is not in the water, does not work (burnt out or breakage).

Make sure there is water in the tank by looking into the drum. Next, having removed the back wall, check the heating element with a tester:

F04, F08 - pressure switch (water level switch).

The presence of a signal from the connector J3.

Check the condition of the level sensor:

– contacts-2-4 are closed – “EMPTY TANK” level
– contacts 2-3 are closed – “FULL TANK” level
– contacts 2-1 are closed – “OVERFLOW” level (not less than half of the loading door glass level.

Remove the top cover by unscrewing the two screws at the back. This sensor is on the top:

Why is he needed?

To adjust the water level in the tank: low, medium and high. It also provides protection against overfilling the tank.

How to check?
We just blow into it. Clicks should be heard. There may be three of them. Depends on the water levels provided by the program: economical, delicate, half load.

F09 The memory card of the electronic board is faulty.

F10 - water intake time exceeded.

The filler pipe from the detergent cuvette to the tank may be clogged, the water inlet valve does not work properly.

Also check the level sensor (see above).

F11 drain pump problem.

The resistance of the pump winding should be about 170 ohms - measure with a tester.
Follow the instructions for error F05

F12 - there is no signal between the control board and the program selector.

Perform an external inspection of the board for damage to the elements.

If burnt nodes are not identified, diagnostics of the control module is required, its flashing.

F13, F14, F15 the drying heater is faulty (washers where there is a drying function).

F16 - the breakdown is related to the blocking of the drum (top-loading machines).

F17 - hatch lock problem.

No power to the door lock - ring the contacts.

Module diagnostics required.

H20 - no water flow error.

It often happens that this is a clogged inlet filter, and there is no water flow due to dirt.

We unscrew the inlet hose, clean the filter mesh at the inlet

In addition, check the water pressure at the inlet of the solenoid inlet valve and its serviceability.

More common Hotpoint Ariston malfunctions:

The washing program does not start, the sunroof lock light blinks frequently:

Gives an error and drains the water.

Change motor brushes.
Lay the washing machine on its side so that you have free access from below.
Attention! The detergent dispenser must be at the bottom to prevent water from entering the control board!

Disconnect the power connectors and unscrew the engine from the tank.

Do not forget to clean the collector between the motor lamellas. They are covered with an abundant layer of graphite dust. It must be removed. The best way to do this is with a vacuum cleaner. The engine manifold should be cleaned with the abrasive part of the dishwashing sponge, and the degree of wear should be visually checked.

We install the engine in place, stick the connectors, but do not put on the drive belt. It is necessary to perform the lapping procedure of the brushes without load. To do this, we start the spin mode at the minimum available speed, visually and aurally controlling the operation of the engine. It should be smooth and without excessive sparking. Then we put on the belt, and once again start the spin cycle at minimum speed with an empty drum.

Water is not supplied, the drum is not spinning (motor is not running):

The door is blocked, the display shows the code F-01, error H20

It is necessary to properly organize the drain system. The tip of the hose should be at a height of 60 to 100 cm.

In addition, a break in the jet must be ensured when draining to prevent water being sucked back into the lubricant.

Detailed scheme of the tank with bearings and drum:

001 - screw m8x23 002 - bearing 25 x52 x 15
003 - screw m8x22
004 - bearing 20x47x14 6204 skf
004 - bearing 6206-2z 005 - O-ring 008 - fixing screw + washer
009 - 46 liter tank cross member, 010 - 11 kg upper counterweight 011 - Suspension spring bracket
012 - tank spring l = 181 mm 013 - sight glass gasket 016 - front counterweight
017 - Hose clamp from side 019 - Clamp for pressure switch tube
021 - tank holder 46 l with holes. n1040325
024 - shock absorber 80n hole 8.15 025 - drum ridge 46 l.
029 - cross with seal. 030 - pulley d=210 mm h=20 mm
031 - elastic belt l=1046-1051

The practice of recent years has shown that it is possible to repair the Ariston washing machine with your own hands.

Each master who repairs complex household appliances undergoes a special training course.

As part of this course, the functional and schematic diagram of the Hotpoint Ariston washing machine is studied.

At present, this machine is very popular with consumers. This is due to the versatility of the washing machine and ease of use.

In almost every major city and even in rural areas there are service centers for the maintenance and repair of these units.

Hotpoint Ariston washing machines appeared on the home appliance market many years ago. Today, analysts have almost eighty models that successfully perform their functions.

Each new model carries an additional feature that facilitates the washing process or makes it better.

Among the advantages of the models of this brand, the following should be noted:

high quality washing;
noiselessness;
operational safety;
ergonomic design.

With ease of operation and high reliability, the repair of Ariston machines requires a consistent and accurate approach.

When the Hotpoint Ariston washing machine installed in the bathroom performs its functions properly, very often no maintenance actions are performed.

And only when some malfunctions occur, attention is paid to the condition of the machine. In order to determine the nature of the breakdown, you need to imagine the general scheme of the unit.

If you draw a simplified diagram of a washing machine, then it will consist of the following components and assemblies:

tubular electric heating element - heating element;
Electrical engine;
drain pump - pump;
water inlet valve;
bearings and seals;
sensors and timers.

This is an incomplete list of devices that make up the Hotpoint Ariston washing machine.

However, it gives an idea of how the machine works and what connections exist between individual devices and mechanisms.

Initially, any model is designed in such a way as to save water and electricity. Particular attention is paid to the consumption of detergents.

All these resources are combined in such proportions to provide a gentle washing regime. Products from different fabrics are erased in different ways.

Washing modes are set using special sensors and control devices.

Self-repair of the washing machine should begin with an assessment of the malfunction.

When the machine is working normally in all modes, but the quality of the wash is declining, and the spinning is practically not performed, you need to inspect the drain hose.

The used water enters the hose through the outlet filter. The video shows the procedure for removing and cleaning the filter. This is a standard operation.

In such a situation, it is necessary to clean not only the filter, but also all pipes adjacent to it.Even when large objects such as coins, buttons and key rings do not enter the filter, dirt accumulates here over time.If cleaning the outlet filter and hose at the Hotpoint Ariston washing machine did not bring results, then you have to remove and repair the drain pump. It is easy to take it off by hand.As a rule, threads are wound on the impeller, which are separated from the laundry during washing. This leads to a decrease in the speed and even deformation of the impeller.As a result, the impeller begins to touch the casing. And this crack is perceived as a signal of a serious breakdown.In this case, in order to eliminate the defect that has arisen, the impeller can be carefully cut with a knife or scissors literally by 1-2 mm.The regular operation of the Hotpoint Ariston washing machine largely depends on the quality of the water.Despite the fact that tap water is purified and softened, a certain concentration of salts remains in it. These salts, when heated, settle on the heating element in the form of scale.Over time, the heating element loses its original characteristics.The water heats up more slowly and the washing quality decreases.To correct the current situation, you need to either replace the heater or clean it from scale.On the video you can see the sequence of actions when replacing the electric heating element. Repairs are easy to do yourself.

Washing machine Hotpoint Ariston Italian manufacturer-reliable and high quality. But some parts of the washing machine sometimes become unusable.

You can, of course, send it to a service center for repair, but in order to save money and with skillful hands and a smart head, you can repair an electromechanical household appliance yourself.

Do-it-yourself Ariston washing machine repair is easy to do. Follow our washing machine restoration instructions, and your assistant will serve you for many years.

In the electromechanical device Ariston, the main reason leading to incorrect operation of the machine is blockages.
In addition, the heating element becomes unusable due to the appearance of limescale on the heating element due to hard water.
The pump is also faulty due to its long operation.
Sometimes the filling valve fails due to damage to the rubber gasket.
In rare cases, it is necessary to change bearings and seals.
Electronics almost never break, but we still touch on the issue of replacing the control unit a little.

It is easy to remove the blockage with your own hands.You need to check the drain filter, which is located at the bottom right under the panel.

By cleaning the filter, you will eliminate the cause of the washing machine malfunction. Less often, there is a blockage of the drain pipe, because it is thick.

The pump may be clogged, but rarely, because there is an additional filter in front of it.

The drain hose only becomes clogged if you installed it incorrectly.

Check the drain, it may also be clogged. Disassemble the unit, pull out the pipe, loosen the clamps, rinse it. Pull out the pump by unscrewing the fasteners and disconnecting the sensors.

Signs of a pump failure:

Drain pump hums but water won't drain.
The machine may stop while the system is running.
Water flows out slowly.

Ariston washing machine pump repair should be done as follows:

If the filling valve is broken in Ariston, then water constantly flows into the washer, even when it is not working, it is disconnected from the network.

To check the fill valve, you need to unscrew the fasteners and remove the top cover. The valve is located where the drain hose connects to the housing of the electromechanical unit.

Check gaskets first. If they have not lost their performance, measure the resistance of the valve. Put the probes on the contacts of the filling valve and check the resistance if it is optimal (from 30 to 50 ohms).

If it is less or more than it should be, it means that the water intake valve is not working. To replace it, you need to unscrew the old valve from the body and screw in a new one. Be sure to connect the sensors.

If the heating element is faulty, then it must be replaced. Its breakdown is signaled by the fact that the water does not heat up or washing according to all programs takes place in cold water. Sometimes the machine gives an error and stops.

To replace the heating element, the rear wall must be removed. Under the tank there are two contacts with a fastener in the middle. This is the ten. Measure the resistance of the heating element with a multimeter.

If the resistance is within the normal range, then you do not need to change the heating element - it is serviceable. To remove the heating element, you need to unscrew the screw in the middle and pull it towards you with rocking movements.

The water may not heat up due to the fragile connection of the wires to the heating element, which arises from the strong vibration of the washer. Water heating may be absent even if the temperature sensor malfunctions.

Take a tester or multimeter and check the resistance of the sensor cold and hot. If the resistance is the same, then it is broken and needs to be replaced. The resistance must be different.

The high-quality and durable material from which the drum of household appliances is made also becomes unusable, because solid foreign objects get into it, which can damage the assembly, forming cracks on it.

The plastic rib inside the drum can be deformed. To replace the drum, you need to remove it.

To remove the drum yourself, you need the following set of tools:

a set of screwdrivers, especially a Phillips screwdriver and a slotted nozzle;
screwdriver;
pliers;
hammer;
hexagons of different sizes.

Using a Phillips screwdriver, the bolts are removed from the rear, front and top walls, and then the panels themselves are removed.

Remove the powder container. Remove the module with a slotted screwdriver. The control unit does not have to be unscrewed to the end, the main thing is that it does not interfere with removing the drum.

Remove the cuff of the hatch, pull out the lower bar by unscrewing the screws. From the loading tank, you need to dismantle the electronics, shock absorbers and other parts.

Remove the drum from the device and disassemble it. Remove the screws holding the two sides of the drum.Pry off the seals with a screwdriver and remove them.

In the drum, the bearing can break and wear out. It needs to be replaced. You only need to buy a bearing of the appropriate brand in a specialized store or order it on the official website of the Ariston washing machine, or purchase it at an equipment repair shop.

Use a metal rod and a hammer to knock out the bearings. If they are faulty, replace them. If the drum is deformed, then change it to a new one.

Reassemble. If the malfunction is in the plastic rib, then there is no need to disassemble the tank. The washer door is removed. A metal rod is taken, the diameter of which is smaller than the holes in the plastic rib of the drum.

The rod is inserted into one of the holes on the rib, the latch is opened with it, the plastic part is removed. A new plastic rib is put in its place. Move the plastic rib along the groove until the latch engages the hole and closes.

The LED indicators that the control panel is equipped with receive a signal from a faulty unit. An error code is displayed on the display, indicating a breakdown of some element.In the Ariston Margarita 2000 washing machine, in the event of a malfunction, the power button starts flashing and the handle of the command device constantly rotates. The nature of the flashing is different depending on the fault. The codes can be found in the owner's manual. Image - Hotpoint ariston arsl 100 DIY repair

The control unit may fail due to mechanical damage, water ingress on it. Do-it-yourself repair of the control module can be done on your own only when a small part has failed or you need to replace the board completely.

In other cases, please contact the service. Professionals will help you repair, resolder complex electronic circuits.

You need to unscrew the screws on the board or remove the plates with a key, depending on its brand. Remove the control unit, replacing with a new one. Screw the fasteners carefully so as not to damage any part.

The price of the repair depends on its complexity. If the device does not drain the water, then the cost of restoration work ranges from 1200 to 3000 rubles.

Repair of the control module costs more than 3500 rubles. The rattle and knock of the machine can be fixed at a service center in Moscow for a price of 3,000 to 5,000 rubles.

Today we shared with you the knowledge of how to repair the Ariston washing machine with our own hands.

We hope that everything will work out for you and self-repair will cost you inexpensively, you will not have to pay for disassembly and assembly of washing equipment, for restoration work with the help of specialists.

Models of Hotpoint and Margarita washing machines from the Italian manufacturer Ariston are rightfully considered one of the most reliable, ergonomic and high-quality among numerous competitors. However, even with them, sometimes unforeseen failures occur, which can be completely eliminated with your own hands.

Before you start repairing the machine, you should first figure out what most often malfunctions lead to the failure of the unit and determine the code of possible malfunctions.

The stability of the Ariston machines, first of all, depends on their correct operation. If there are certain problems, then you can try to fix them on your own, without resorting to the help of a specialist. But for this you need to figure out what most often can cause malfunctions.

Perhaps one of the most common causes of problems in the operation of the machine is blockages that prevent the passage of water during the process of draining it, which, in turn, leads to the inability of the washer to reconfigure the rinse mode. Characteristic signs of this problem are idling, loud noise and the impossibility of passing water through the hose (or very poor water permeability). As for places of blockage, then they can be concentrated:

in the drain hose itself, and in most cases blockages occur if it is installed incorrectly;
often blockages form in the drain filter itself;
blockages may occur in the pipe, which is located between the drain filter and the tank;
and also in the pump, although this is an extremely rare practice.

In order to correct the situation and eliminate the malfunction, it is enough to clean the machine from blockages in accessible places (pump, hose, drain pump or pipe).

The second problem that can be encountered during the operation of Ariston machines is lack of water heating during the erasing process. Often, in such a situation, the washing machine can be shocked due to dysfunction of the insulation of the heating element.

The main reason that provokes such a malfunction is extremely hard water, resulting in the formation of scale. Repair consists in replacing a damaged electric heater (heater). To do this, unscrew the back panel of the machine, since it is behind it that the fastener of the broken electric heater is located. First, disconnect all contacts and unscrew the fixing screw, then carefully pull out the broken heater and replace the part with a new one. Everything, the malfunction is fixed, and the machine should heat the water, as before.

The most difficult problem is the breakdown or partial wear of the bearing or seal at Ariston. Fortunately, in practice, it is extremely rare.

To understand that machine malfunctions are result of bearing failurejust pay attention to the following signs:

during the operation of the unit, all moving elements of the washer begin to make characteristic sounds during the spin cycle;
in this case, the shaft begins to come into contact with the sleeve;
vibrations are possible.

It must be said right away that this problem should be removed promptly, because otherwise you can just break the machine. The only difficulty is that the repair will require almost complete disassembly of the machine. Therefore, if there is no confidence in your actions, it is best to entrust this process to a professional.

In this case, most likely there is a malfunction associated with socket or power cord. To check the operation of the outlet, just try turning on another electrical appliance. If everything is in order with the outlet, then you need to check the wire itself. To do this, it must be disconnected from the outlet and try to “ring” with a special tester.

In the event that the electrical wire is normal, then most likely the problem is hidden directly in the power supply of the machine. This is a rather complex problem, so only an experienced professional can solve it.

It is interesting! How to open the washing machine yourself if it is blocked

Another problem that can cause the machine to stop working is no drum rotation. There are several reasons that can cause such a situation: engine breakdown; problems with electrical wiring; collection in the operation of the control panel or clogging of the filter. However, the most common cause is wear or severe stretching of the belt. In this case, you need to replace it - there should not be any special problems with self-replacement.

If the reason is different, then it is best to call a professional at home to identify the cause of the breakdown of the machine.

An equally common problem that users of Ariston Hotpoint or Margarita typewriters may encounter is a malfunction that occurs directly in the control unit. The main reason for this problem is a malfunction of our electrical networks, which is extremely problematic to deal with on our own.

In this case, the problem is easier to prevent than to fix. Therefore, before you start operating the washing machine, in particular, Ariston, it is best to put special protective equipment, which help protect the washer from power surges and other similar failures.This approach will be much more efficient and economical than replacing the entire control unit.

Operational problems may also arise during loose or broken mechanical fastenerswith which the machine is equipped. Most often, this is expressed in weakening the fixation of the hatch of the machine. The problem has the following symptoms: strong noise during the operation of the washer and characteristic vibrations. To get rid of this, it is enough to tighten or completely replace the fasteners with new ones.

It should be noted that such models of Ariston washing machines as Margarita 2000, Hotpoint, Avsl 109 and others have unique self-diagnosis function. The bottom line is that the system independently detects a malfunction and shows on the display or by flashing indicators, its specific code. Having an idea of \u200b\u200bwhat code number the unit shows, you can independently identify the problem and fix it.

It is interesting! Reasons why the washing machine does not draw water

Having an idea of what most often failures can occur in Ariston typewriters, you can try independently repair the unit. However, it should be started only if there is confidence in their actions. If there is no experience in such things, it is best to entrust the repair of the washer to a specialist.

Ariston washing machines from an Italian manufacturer can be called a "model of reliability and quality", but they sometimes require attention. Repair of Ariston washing machines in some cases can be done by hand, and a specialist needs to be involved only in the most difficult cases.

In this article, we will analyze the frequent malfunctions of Hotpoint Ariston automatic washing machines, study the “symptoms” of such breakdowns and decide how to properly repair it yourself.

The vast majority of breakdowns of Ariston washing machines are related to their operation. This is recognized by the masters of service centers for the repair of washing machines. Sometimes we are talking about frankly improper operation, the user regularly makes gross mistakes, which lead to a breakdown. But most often, the cause of the breakdown is the operating conditions, which the user either did not know about, or guessed, but did nothing. A vivid example is hard water, which can completely disable the “home helper”!

So, what breakdowns are most often found on Hotpoint Ariston washing machines? We decided to compile a kind of rating of the frequency of breakdowns. When compiling the rating, we rely on statistical data provided by the leading service centers for the repair of washing machines.

blockages. Blockages themselves can hardly be considered breakdowns; rather, they are the cause of various breakdowns. However, it is blockages that craftsmen have to deal with most often, and it is strong blockages that most often paralyze the operation of various Hotpoint Ariston washing machines.
A heating element. In second place in our ranking is ten. Despite the fact that the heating element itself is of high quality, low-quality hard water does its job. Over time, the scale layer destroys even the best part and it has to be changed.
Water pump. In third place is the drain pump or pump. This part fails quite rarely and in most cases the reason is wear and tear from long-term operation.
Fill valve. Even more rarely, the filling valve fails. More precisely, not even the valve itself, but a rubber gasket. Rubber becomes dull over time and begins to let water through, this causes a malfunction. The gasket itself costs a penny, but the services of a master in replacing this gasket cannot be called cheap.
Bearings and seals. In fifth place are the breakdowns of bearings and seals.On Hotpoint Ariston washing machines, this is a rarity, but if such a breakdown occurs, you cannot continue to operate the machine.

Important! The electrics and electronics of the Hotpoint Ariston washing machine are intentionally not included in the rating, since it breaks very rarely.

If you have problems with blockages on the Hotpoint Ariston washing machine, do not rush to call the master, everything can be repaired quickly, with your own hands. How do you know that you are dealing with a blockage? The main sign of a blockage in the drain system is the idle operation of the drain pump, that is, it buzzes, but the water does not leave the tank. Usually, this trouble appears after the end of washing, the machine cannot drain the waste water to start rinsing and freezes, or it drains the water too slowly.

Strong blockage can be in several places:

in the drain pipe, between the tank and the drain filter - this happens less often, since the pipe is quite thick;
in the drain filter - there the blockage forms most often;
in the pump - in Ariston washing machines, blockages in the pump are rare, since an additional filter is installed in front of the drain pump;
in the drain hose - blockages rarely occur, mainly in cases where the hose was not installed correctly.

How to quickly clear blockages? First of all, you need to check and clean the easily accessible places of the washing machine where a blockage could occur. First, unscrew the drain filter, which is located on the Ariston machines at the bottom right under the narrow panel. Before unscrewing the filter, put a rag under it, as water will flow from it. Remove all debris from the filter, and then screw it back on.

Next, it is important to check the drain hose and sewer. In some situations, a banal blockage in the drain pipe can force the user to turn to machine repair specialists when it was more correct to turn to plumbers. And if everything is in perfect order, then it will be necessary to disassemble the machine, clean the nozzles and the pump. To remove the pipe, you will need to loosen two clamps, and to remove the pump, you will need to disconnect it from the sensors and unscrew the two fasteners.

If any malfunction occurs, the Hotpoint Ariston “washer” gives an error with a specific cipher displayed on the screen. It is very important to correctly recognize the error codes of Ariston washing machines, because this is a direct clue indicating the cause of the breakdown.

A broken inlet valve “according to symptoms” is quite difficult to confuse with other breakdowns of the Hotpoint Ariston washing machine. When the inlet valve stops shutting off the water, water begins to flow into the washing machine tank by gravity, even if the “home assistant” is turned off from the network.

If you hear the characteristic murmur of water being poured into and drained from the tank when the machine is turned off, be sure this is a valve.

To check the filling valve, you need to remove the top cover of the Hotpoint Ariston machine by unscrewing the two fasteners. The valve is located at the junction of the inlet hose with the body of the machine. First of all, we check the gaskets, if they are intact, then you need to measure the resistance of the device, and for this you will have to use a multimeter. We install the probes on the contacts of the filling valve and check. The device should show approximately 30 to 50 ohms.

A defective filling valve should be replaced with a similar one; self-repair is not possible. The replacement itself is done very quickly, we unscrew the old valve from the body and screw in the new one, not forgetting to connect the sensors. It is worse if the pump fails, because this is a rather expensive part.

A faulty pump gives itself out during washing, when the machine should drain the water, but it does not, while the pump either does not make any sounds at all, or it buzzes, but the murmur of the drained water is not audible.

Note! Strictly speaking, these symptoms are superficial and may be indicative of other problems (such as electronics), but it should make you think about checking the pump first.

In the Hotpoint Ariston washing machine, it is located at the bottom and you can get to it through the bottom. It is better to check and replace the drain pump by a specialist, but you can do everything yourself, the main thing is to thoroughly study the progress of work.

The heating element is an important part of the washing machine, responsible for the temperature of the water in the tank, and therefore for the quality of the wash. If the heating element is faulty, the wash either does not start at all, and the system gives an error, or the wash is performed in cold water. Both should prompt you to check and replace the heating element in the Hotpoint Ariston washing machine.

Checking the heating element of the Ariston washing machine is not difficult at all. It is necessary to deploy the machine, in the lower part of the rear wall there is a service hatch, which is attached to the clamps and several self-tapping screws. We unscrew the screws, and squeeze the latches with a screwdriver, after which the cover will be removed. Behind the lid, under the tank, you will see two large contacts with a fastener in the middle - this is the heating element. We unscrew the screw, and then we begin to pull the heating element towards ourselves, pulling it out with swaying movements.

Note! Before pulling out the heating element, it’s a good idea to measure the resistance with a multimeter, perhaps the device is working, and you don’t need to touch it.

As we have already noted, failures of bearings and seals are the most rare malfunctions of Ariston washing machines. However, if this happens, urgent action must be taken. Recognizing such a breakdown is not difficult. When the bearing is destroyed, the moving elements begin to make unpleasant sounds, the shaft begins to rub against the bushing, which leads to wear. And if you do not take any measures and continue to wash, then this can lead to the fact that the drum will begin to play and damage the tank.

So that your favorite washing machine does not end up in a landfill, you need to contact a specialist when such sounds appear, or try to change the bearings yourself. If you are determined to do the work yourself, study the information offered on our website. Otherwise, with such a complex repair, it is not surprising to make serious mistakes. The main difficulty is that in order to get to the bearings, you need to disassemble the entire washing machine, along with the tank.

In addition, it will be necessary to correctly remove the old bearings without damaging the sleeve, and then correctly install the new ones so that re-repair is not required. Without proper skill, self-repair is not possible for many, so before taking on work, consider delegating it to a specialist.

In conclusion, we note that it is theoretically possible to repair malfunctions of Ariston machines with your own hands, especially if you have the time and patience. But still, in order to avoid mistakes and unnecessary expenses, it is better to contact a specialist because “the miser pays twice”!

Video (click to play).