In detail: hotpoint ariston vertical washing machine DIY repair from a real master for the site my.housecope.com.
People buy washing machines with top loading much less often than with front loading - this is a fact.
The tightness of the parts of the machine makes it difficult to disassemble
Increased vibration during spinning
On some machines it is not possible to level the rear feet
Corrosion of the top cover from moisture
Spontaneous opening of the drum flaps in case of imbalance
Narrow and deep, and fits perfectly into confined spaces in the bathtub, closets or kitchen
No need to bend over to load the laundry
Ability to interrupt the program and add laundry
Child safety. Control panel location.
Features and nuances for self-repair of vertical units:
The device contains the same elements (pressure switch, water intake valve, drum, tank, control board, pump, and so on). The axis of the drum is structurally made on two bearings; a self-positioning sensor is sometimes located on the tank (fixing the drum with the flaps up).
We will show the dismantling of units using the example of Electrolux:
1.From the sides, using a screwdriver, release the control panel 2.Pull the plastic panel up and slide towards you 3. We tilt at a small angle towards ourselves to dismantle the wires from the board connectors 4. Take out the panel
To remove the electronic control module, disconnect the remaining wires and unscrew the screws shown in the figure. For quick and correct assembly, take pictures of the connection points of the wire loops.
To remove the water inlet valve, disconnect the rubber hoses from the clamps and dismantle them. Detach the wires and from the outside press on the holes to push out the valve.
To remove the side panels, unscrew a few screws, do not forget to save the washers for grounding the case. Bend the wall from below with your hand and slide it down.
After removing the two side panels, access to the screws for dismantling the front panel appeared.
To remove the NTC sensors and self-positioning the DSP drum, it is enough to remove the right wall and dismantle them.
Frequent malfunction - there is no way to change the program .:
Example - Hotpoint Ariston ARTL 1047.
Many "craftsmen" sin that the control module is to blame for everything. But no!
It is enough to unscrew the two screws from the back and remove the control panel.
This very cracked handle is the culprit. Use the metal ring (the plug from the antenna for example).
By squeezing the plastic handle, the ring will prevent programs from skipping.
Blown up top of the Indesite vertical, Ariston:
Video (click to play).
001 - control knob 002 - white on-off / reset buttons 003 - white control panel 004 - bitron switch 005 - function keys 007 - display 008 - cover handle 010 - dispenser unlocking lever 011 - dispenser hook spring 012 - disengagement button dispenser 016 - cover support 018 - partition with shock absorber 021 - door interlock device 022 - white dispenser 023 - siphon cover 026 - control panel wiring 027 - 8-pos. potentiometer
There is an opinion that two drum supports instead of one are good.
This is not the case, and in the case of "vertical" it is just a forced engineering decision. The service life of the drum bearings does not increase for a minute.
If the screws are hard to loosen, heat them up with a blowtorch.
Use a special grease for oil seals - Litol-24, TsIATIM-221, SHRUS-4M, etc.
On "Kandy", in order to change the bearings, you need to disassemble the entire machine to the screw! And what is the wild tightness in the depths of the "vertical". Sometimes you have to do everything literally by touch.
Washing machines Ariston from the Italian manufacturer can be called "a model of reliability and quality", but they sometimes require attention. In some cases, repair of Ariston washing machines can be done by hand, and a specialist needs to be involved only in the most difficult cases.
Within the framework of this article, we will analyze the frequent malfunctions of automatic washing machines of the Hotpoint Ariston brand, study the "symptoms" of such breakdowns and decide how to properly make an independent repair.
The vast majority of breakdowns of Ariston washing machines are associated with their operation. This is recognized by the masters of service centers for the repair of washing machines. Sometimes we are talking about frankly incorrect operation, the user regularly makes gross mistakes, which lead to breakdown. But most often, the cause of the breakdown is the operating conditions, which the user either did not know about, or guessed, but did nothing. A striking example is hard water, which can completely disable the "home helper"!
So, what are the most common breakdowns on Hotpoint Ariston washing machines? We decided to compile a kind of breakdown frequency rating. When compiling the rating, we rely on statistical data provided by leading service centers for the repair of washing machines.
Blockages. The blockages themselves can hardly be considered breakdowns; rather, this is the cause of various breakdowns. Nevertheless, it is with blockages that craftsmen have to deal with most often, and it is strong blockages that most often paralyze the operation of various Hotpoint Ariston washing machines.
A heating element. Teng is in second place in our rating. Despite the fact that the heating element itself is of high quality, low-quality hard water does its job. Over time, the scale layer destroys even the best part and has to be replaced.
Water pump. In third place is the drain pump or pump. This part fails quite rarely and in most cases the reason is wear from prolonged operation.
Filling valve. Even less often, the filler valve fails. More precisely, not even the valve itself, but a rubber gasket. Over time, rubber dubs and begins to let water through, and this causes a malfunction. The gasket itself costs a penny, but the services of a master to replace this gasket are by no means cheap.
Bearings and seals. In fifth place are the failures of bearings and oil seals. On Hotpoint Ariston washing machines, this is a rarity, but if such a breakdown appears, you cannot continue to operate the machine.
Important! The electrics and electronics of the Hotpoint Ariston washing machine are deliberately not included in the rating, since it rarely breaks down.
If you have problems with blockages on the Hotpoint Ariston washing machine, do not rush to call the master, everything can be repaired quickly, with your own hands. How do you know that you are dealing with a blockage? The main sign of a blockage in the drain system is the idle operation of the drain pump, that is, it hums, but the water does not leave the tank. Usually, this trouble manifests itself after the end of the wash, the machine cannot drain the waste water to start rinsing and freezes, or it drains the water too slowly.
A strong blockage can be found in several places:
in the drain pipe, between the tank and the drain filter - this happens less often, since the pipe is quite thick;
in the drain filter - there is a blockage most often;
in the pump - in Ariston washing machines, blockages in the pump are rare, since an additional filter is installed in front of the drain pump;
in the drain hose - blockages rarely occur, mainly in cases where the hose was installed incorrectly.
How to quickly remove a blockage? First of all, you need to check and clean the easily accessible places of the washing machine, where a blockage could occur. First, we unscrew the drain filter, which is located on the Ariston machines at the bottom right under the narrow panel. Place a cloth on the filter before unscrewing it as water will drip off. Remove all debris from the filter and then screw it back on.
Next, it is important to check the drain hose and drain. In a number of situations, a banal blockage in the drain pipe can force the user to contact a machine repair specialist, when it was more correct to contact a plumber. And if everything is in perfect order, then you will need to disassemble the machine, clean the pipes and the pump. To remove the pipe, you will need to loosen two clamps, and to remove the pump, you will need to disconnect it from the sensors and unscrew the two fasteners.
If any malfunction occurs, the Hotpoint Ariston "washing machine" gives an error with a specific code displayed on the screen. It is very important to recognize the error codes of Ariston washing machines correctly, because this is a direct clue indicating the cause of the breakdown.
A broken filler valve "symptomatically" is quite difficult to confuse with other breakdowns of the Hotpoint Ariston washing machine. When the filling valve stops blocking the water, water begins to flow into the washing machine tank by gravity, even if the “home assistant” is turned off from the network.
If you hear the characteristic murmur of water being poured and drained from the tank when the machine is turned off, be sure this is a valve.
To check the filler valve, remove the top cover of the Hotpoint Ariston by unscrewing the two fasteners. The valve is located at the junction of the inlet hose with the machine body. First of all, we check the gaskets, if they are intact, then you need to measure the resistance of the device, and for this you will have to use a multimeter. We install the probes on the contacts of the filler valve and check. The meter should read approximately 30 to 50 ohms.
A defective filling valve should be replaced with a similar one; self-repair is not possible. The replacement itself is done very quickly, we unscrew the old valve from the body and screw in a new one, not forgetting to connect the sensors. It is worse if the pump is out of order, because it is a rather expensive part.
A faulty pump gives itself out during washing, when the machine should drain the water, but it does not, while the pump either does not make any sounds at all, or it hums, but the murmur of the drained water is not audible.
Note! Strictly speaking, these symptoms are superficial and they may indicate other problems (for example, with electronics), but this should give you the idea to check your pump first.
In the Hotpoint Ariston washing machine, it is at the bottom and can be reached through the bottom. It is better to check and replace the drain pump by a specialist, but you can do everything yourself, the main thing is to thoroughly study the progress of work.
The heating element is an important part of the washing machine, which is responsible for the temperature of the water in the tub, and therefore for the quality of the wash. If the heating element is faulty, the wash either does not start at all, and the system generates an error, or the wash is performed in cold water. Both should prompt you to check and replace the heating element in the Hotpoint Ariston washing machine.
Checking the heating element of the Ariston washing machine is not difficult at all. It is necessary to unfold the machine, at the bottom of the rear wall there is a service hatch, which is attached to the clips and several screws. We unscrew the self-tapping screws, and wring out the clamps with a screwdriver, after which the cover will be removed. Behind the lid, under the tank, you will see two large contacts with the fastener in the middle - this is the heating element.We unscrew the screw, and then we begin to pull the ten on ourselves, pulling it out with swaying movements.
Note! Before pulling out the heating element, it is a good idea to measure the resistance with a multimeter, perhaps the device is working properly and does not need to be touched.
As we have already noted, bearing and oil seal failures are the most rare malfunctions of Ariston washing machines. However, if this happens, then urgent action is needed. It is not difficult to recognize such a breakdown. When the bearing is destroyed, the moving elements begin to emit unpleasant sounds, the shaft begins to rub against the bushing, which leads to a depletion. If you do not take any measures and continue washing, this can lead to the fact that the drum begins to play and damage the tank.
To prevent your favorite washing machine from ending up in a landfill, you need to contact a specialist when such sounds appear, or try to change the bearings yourself. If you are determined to do the work yourself, study the information offered on our website. Otherwise, with such a complex repair, it is not surprising to make serious mistakes. The main difficulty is that in order to get to the bearings, you need to disassemble the entire washing machine, along with the tank.
In addition, it will be necessary to correctly remove the old bearings without damaging the bushing, and then install the new ones correctly so that repeated repairs are not required. Without the proper skill, not many can do self-repair, so before starting work, think about delegating it to a specialist.
In conclusion, we note that the repair of malfunctions of Ariston machines can theoretically be done by hand, especially if you have the time and patience. But all the same, in order to avoid mistakes and unnecessary expenses, it is better to turn to a specialist, because “a miser pays twice”!
Washing machine Hotpoint Ariston of the Italian manufacturer is reliable and of high quality. But some parts of the washing machine sometimes become unusable.
You can, of course, send it to a service center for repair, but in order to save money and with skillful hands and a smart head, you can independently repair an electromechanical household appliance.
Do-it-yourself repair of the Ariston washing machine is easy to do. Follow our instructions for restoring the washing machine, and your assistant will serve you for many years.
In the Ariston electromechanical device, the main reason for the incorrect operation of the machine is blockages.
In addition, the heating element becomes unusable due to the appearance of limescale on the heating element due to hard water.
The pump can also be faulty due to its long operation.
Sometimes the filler valve fails due to damage to the rubber gasket.
In rare cases, bearings and seals have to be changed.
Electronics almost never breaks down, but we will still touch on the issue of replacing the control unit a little.
It is easy to remove the blockage with your own hands. You need to check the drain filter, which is located on the lower right under the panel.
After cleaning the filter, you will eliminate the cause of the malfunction of the washing machine. Less commonly, the drain pipe is clogged because it is thick.
There may be a blockage in the pump, but rarely, because there is an additional filter in front of it.
The drain hose will only become clogged if you have not installed it correctly.
Check the drain, there may be a blockage in it too. Disassemble the unit, pull out the branch pipe by loosening the clamps, flush it. Pull out the pump by unscrewing the fasteners and disconnecting the sensors.
Signs of a pump breakdown:
The drain pump hums, but the water does not drain.
The machine may stop when the system is running.
Water flows out slowly.
Repair of the pump of the Ariston washing machine must be done as follows:
If the filler valve is broken in Ariston, then water constantly flows into the washer, even when it is not working, it is disconnected from the network.
To check the filler valve, you need to unscrew the fasteners and remove the top cover. The valve is located where the drain hose connects to the body of the electromechanical unit.
Check the gaskets first. If they have not lost their performance, measure the resistance of the valve. Put the probes on the contacts of the filler valve and check the resistance, whether it is optimal (from 30 to 50 ohms).
If it is less or more than the set value, it means that the water intake valve is not working. To replace it, you need to unscrew the old valve from the body and screw in a new one. Be sure to connect the sensors.
If the heating element is faulty, then it is imperative to replace it. Its breakdown is indicated by the fact that the water does not heat up or washing in all programs takes place in cold water. Sometimes the machine gives an error and stops.
To replace the heating element, the rear wall must be removed. There are two contacts under the tank with a fastener in the middle. This is ten. Measure the resistance of the heating element with a multimeter.
If the resistance is within the normal range, then there is no need to change the heating element - it is serviceable. To remove the heating element, you need to unscrew the screw in the middle and pull it towards you with swinging movements.
The water may not heat up also due to the fragile connection of the wires to the heating element, which arises from the strong vibration of the washing machine. Water heating may also be absent if the temperature sensor is faulty.
Take a tester or multimeter and check the resistance of the sensor when cold and hot. If the resistance is the same, then it is broken, requires replacement. The resistance should be different.
The high-quality and durable material from which the drum of household appliances is made also becomes unusable, because solid foreign objects get into it, which can damage the unit, forming cracks on it.
The plastic rib inside the drum can deform. Remove the drum to replace it.
To remove the drum yourself, you need the following set of tools:
a set of screwdrivers, especially a Phillips screwdriver and a slotted nozzle are needed;
screwdriver;
pliers;
hammer;
hexagons of different sizes.
Use a Phillips screwdriver to remove the bolts from the back, front, and top walls, and then remove the panels themselves.
Dismantle the powder container. Use a slotted screwdriver to remove the module. It is not necessary to unscrew the control unit to the end, the main thing is that it does not interfere with the removal of the drum.
Remove the hatch cuff, pull out the lower bar by unscrewing the screws. It is necessary to dismantle electronics, shock absorbers and other parts from the loading tank.
Remove the drum from the device and disassemble it. Remove the screws holding the two sides of the drum. Pry the oil seals with a screwdriver and remove them.
The bearing in the drum can break and wear. It needs to be replaced. You only need to buy a bearing of the corresponding brand in a specialized store or order it on the official website of the Ariston washing machine, possibly purchase it in an equipment repair workshop.
Use a metal rod and a hammer to knock out the bearings. If they are defective, replace them. If the drum is deformed, replace it with a new one.
Reassemble. If the malfunction is in the plastic rib, then you do not need to disassemble the tank. The washer door is removed. A metal rod is taken, the diameter of which is smaller than the holes in the plastic rib of the drum.
The rod is inserted into one of the holes on the rib, the latch is opened with it, the plastic part is removed. A new plastic rib is put in its place. Slide along the groove with the plastic rib until the latch enters the hole and closes.
