Details: hotpoint ariston vertical washing machine do-it-yourself repair from a real master for the site my.housecope.com.
People buy top-loading washing machines much less often than front-loading washing machines - that's a fact.
The tightness of the machine nodes creates difficulties during disassembly
Increased vibration on spin
On some machines it is not possible to adjust the level of the rear legs
Corrosion of the top cover from moisture
Spontaneous opening of the drum flaps when unbalanced
Narrow and deep, it fits perfectly into tight spaces in the bathtub, pantry or kitchen
No need to bend down to load laundry
Possibility to interrupt the program and add laundry
Safety from children. Control panel location.
Features and nuances for self-repair of verticals:
The device contains the same elements (pressure switch, water intake valve, drum, tank, control board, pump, and so on). The axis of the drum is structurally made on two bearings, sometimes a self-positioning sensor is located on the tank (fixing the drum with the flaps up).
We will show the dismantling of nodes using the example of Electrolux:
1. From the sides, using a screwdriver, release the control panel 2.Pull the plastic panel up and slide it towards you 3. We tilt at a small angle towards ourselves to dismantle the wires from the board connectors 4. Remove the panel
To remove the electronic control module, disconnect the remaining wires and unscrew the screws shown in the figure. For quick and correct assembly, take a picture of the connection points of the wire loops.
To remove the water inlet valve, disconnect the rubber hoses from the clamps and dismantle them. Disconnect the wires and from the outside press the holes to extrude the valve.
To remove the side panels, unscrew a few screws, do not forget to save the washers for grounding the case. Bend the wall from below with your hand and slide it down.
After removing the two sides, access to the screws for dismantling the front panel appeared. Unscrew them.
To remove the NTC sensors and self-position the DSP drum, it is enough to remove the right wall and dismantle them.
Frequent malfunction - it is not possible to change the program.:
An example is Hotpoint Ariston ARTL 1047.
Many "craftsmen" sin that the control module is to blame for everything. But no!
It is enough to unscrew the two bolts from the back side and remove the control panel.
This very cracked handle is the culprit. Use a metal ring (an antenna plug for an example).
By squeezing the plastic handle, the ring will prevent programs from skipping.
Exploded top vertical Indesit, Ariston:
Video (click to play).
001 - control knob 002 - white on-off/reset buttons 003 - white control panel 004 - bitron switch 005 - function keys 007 - display 008 - Lid handle 010 - Dispenser release lever 011 - Dispenser hook spring 012 - Dispenser release button 016 - Lid support 018 - bulkhead with shock absorber 021 - door interlock 022 - white dispenser 023 - siphon cover 026 - control panel wiring 027 - 8-pos. potentiometer
There is an opinion that two drum supports instead of one is good.
This is not so, and in the case of the "vertical" it is just a forced engineering decision. The service life of the drum bearings does not increase even for a minute.
If the screws are hard to loosen, heat them up with a blowtorch.
Use a special grease for oil seals - Litol-24, CIATIM-221, SHRUS-4M, etc.
On the Kandy, to change the bearings, you need to disassemble the entire machine to the screw! And what is the wild tightness in the bowels of the "verticals". Sometimes you have to do everything literally by touch.
Ariston washing machines from an Italian manufacturer can be called a "model of reliability and quality", but they sometimes require attention. Repair of Ariston washing machines in some cases can be done by hand, and a specialist needs to be involved only in the most difficult cases.
In this article, we will analyze the frequent malfunctions of Hotpoint Ariston automatic washing machines, study the “symptoms” of such breakdowns and decide how to properly repair it yourself.
The vast majority of breakdowns of Ariston washing machines are related to their operation. This is recognized by the masters of service centers for the repair of washing machines. Sometimes we are talking about frankly improper operation, the user regularly makes gross mistakes, which lead to a breakdown. But most often, the cause of the breakdown is the operating conditions, which the user either did not know about, or guessed, but did nothing. A vivid example is hard water, which can completely disable the “home helper”!
So, what breakdowns are most often found on Hotpoint Ariston washing machines? We decided to compile a kind of rating of the frequency of breakdowns. When compiling the rating, we rely on statistical data provided by the leading service centers for the repair of washing machines.
blockages. Blockages themselves can hardly be considered breakdowns; rather, they are the cause of various breakdowns. However, it is blockages that craftsmen have to deal with most often, and it is strong blockages that most often paralyze the operation of various Hotpoint Ariston washing machines.
A heating element. In second place in our ranking is ten. Despite the fact that the heating element itself is of high quality, low-quality hard water does its job. Over time, the scale layer destroys even the best part and it has to be changed.
Water pump. In third place is the drain pump or pump. This part fails quite rarely and in most cases the reason is wear and tear from long-term operation.
Fill valve. Even more rarely, the filling valve fails. More precisely, not even the valve itself, but a rubber gasket. Rubber becomes dull over time and begins to let water through, this causes a malfunction. The gasket itself costs a penny, but the services of a master in replacing this gasket cannot be called cheap.
Bearings and seals. In fifth place are the breakdowns of bearings and seals. On Hotpoint Ariston washing machines, this is a rarity, but if such a breakdown occurs, you cannot continue to operate the machine.
Important! The electrics and electronics of the Hotpoint Ariston washing machine are intentionally not included in the rating, since it breaks very rarely.
If you have problems with blockages on the Hotpoint Ariston washing machine, do not rush to call the master, everything can be repaired quickly, with your own hands. How do you know that you are dealing with a blockage? The main sign of a blockage in the drain system is the idle operation of the drain pump, that is, it is buzzing, but the water does not leave the tank. Usually, this trouble appears after the end of washing, the machine cannot drain the waste water to start rinsing and freezes, or it drains the water too slowly.
Strong blockage can be in several places:
in the drain pipe, between the tank and the drain filter - this happens less often, since the pipe is quite thick;
in the drain filter - there the blockage forms most often;
in the pump - in Ariston washing machines, blockages in the pump are rare, since an additional filter is installed in front of the drain pump;
in the drain hose - blockages rarely occur, mainly in cases where the hose was not installed correctly.
How to quickly clear blockages? First of all, you need to check and clean the easily accessible places of the washing machine where a blockage could occur. First, unscrew the drain filter, which is located on the Ariston machines at the bottom right under the narrow panel. Before unscrewing the filter, put a cloth over it, as water will flow from it. Remove all debris from the filter, and then screw it back on.
Next, it is important to check the drain hose and sewer. In some situations, a banal blockage in the drain pipe can force the user to turn to machine repair specialists when it would be more correct to turn to plumbers. And if everything is in perfect order, then it will be necessary to disassemble the machine, clean the nozzles and the pump. To remove the pipe, you will need to loosen two clamps, and to remove the pump, you will need to disconnect it from the sensors and unscrew the two fasteners.
If any malfunction occurs, the Hotpoint Ariston “washer” gives an error with a certain code displayed on the screen. It is very important to correctly recognize the error codes of Ariston washing machines, because this is a direct clue indicating the cause of the breakdown.
A broken inlet valve “according to symptoms” is quite difficult to confuse with other breakdowns of the Hotpoint Ariston washing machine. When the inlet valve stops shutting off the water, water begins to flow into the washing machine tank by gravity, even if the “home assistant” is turned off from the network.
If you hear the characteristic murmur of water being filled in and drained from the tank when the machine is turned off, be sure this is a valve.
To check the filling valve, you need to remove the top cover of the Hotpoint Ariston machine by unscrewing the two fasteners. The valve is located at the junction of the inlet hose with the body of the machine. First of all, we check the gaskets, if they are intact, then you need to measure the resistance of the device, and for this you will have to use a multimeter. We install the probes on the contacts of the filling valve and check. The device should show approximately 30 to 50 ohms.
A defective filling valve should be replaced with a similar one; self-repair is not possible. The replacement itself is done very quickly, we unscrew the old valve from the body and screw in the new one, not forgetting to connect the sensors. It is worse if the pump fails, because this is a rather expensive part.
A faulty pump gives itself out during washing, when the machine should drain the water, but it does not, while the pump either does not make any sounds at all, or it buzzes, but the murmur of the drained water is not audible.
Note! Strictly speaking, these symptoms are superficial and may be indicative of other problems (eg electronics), but it should make you think to check the pump first.
In the Hotpoint Ariston washing machine, it is located at the bottom and you can get to it through the bottom. It is better to check and replace the drain pump by a specialist, but you can do everything yourself, the main thing is to thoroughly study the progress of work.
The heating element is an important part of the washing machine, responsible for the temperature of the water in the tank, and therefore for the quality of the wash. If the heating element is faulty, the wash either does not start at all, and the system gives an error, or the wash is performed in cold water. Both should prompt you to check and replace the heating element in the Hotpoint Ariston washing machine.
Checking the heating element of the Ariston washing machine is not difficult at all. It is necessary to deploy the machine, in the lower part of the rear wall there is a service hatch, which is attached to the clamps and several self-tapping screws. We unscrew the screws, and squeeze the latches with a screwdriver, after which the cover will be removed. Behind the lid, under the tank, you will see two large contacts with a fastener in the middle - this is the heating element.We unscrew the screw, and then we begin to pull the heating element towards ourselves, pulling it out with shaking movements.
Note! Before pulling out the heating element, it’s a good idea to measure the resistance with a multimeter, perhaps the device is working, and you don’t need to touch it.
As we have already noted, failures of bearings and seals are the most rare malfunctions of Ariston washing machines. However, if this happens, urgent action must be taken. Recognizing such a breakdown is not difficult. When the bearing is destroyed, the moving elements begin to make unpleasant sounds, the shaft begins to rub against the bushing, which leads to wear. And if you do not take any measures and continue to wash, then this can lead to the fact that the drum will begin to play and damage the tank.
So that your favorite washing machine does not end up in a landfill, you need to contact a specialist when such sounds appear, or try to change the bearings yourself. If you are determined to do the work yourself, study the information offered on our website. Otherwise, with such a complex repair, it is not surprising to make serious mistakes. The main difficulty is that in order to get to the bearings, you need to disassemble the entire washing machine, along with the tank.
In addition, it will be necessary to correctly remove the old bearings without damaging the sleeve, and then correctly install the new ones so that re-repair is not required. Without proper skill, self-repair is not possible for many, so before taking on work, consider delegating it to a specialist.
In conclusion, we note that it is theoretically possible to repair malfunctions of Ariston machines with your own hands, especially if you have the time and patience. But still, in order to avoid mistakes and unnecessary expenses, it is better to contact a specialist because "the miser pays twice"!
Washing machine Hotpoint Ariston Italian manufacturer-reliable and high quality. But some parts of the washing machine sometimes become unusable.
You can, of course, send it to a service center for repair, but in order to save money and with skillful hands and a smart head, you can repair an electromechanical household appliance yourself.
Do-it-yourself Ariston washing machine repair is easy to do. Follow our washing machine restoration instructions, and your assistant will serve you for many years.
In the electromechanical device Ariston, the main reason leading to incorrect operation of the machine is blockages.
In addition, the heating element becomes unusable due to the appearance of limescale on the heating element due to hard water.
The pump is also faulty due to its long operation.
Sometimes the filling valve fails due to damage to the rubber gasket.
In rare cases, it is necessary to change bearings and seals.
Electronics almost never break, but we still touch on the issue of replacing the control unit a little.
It is easy to remove the blockage with your own hands. You need to check the drain filter, which is located at the bottom right under the panel.
By cleaning the filter, you will eliminate the cause of the washing machine malfunction. Less often, there is a blockage of the drain pipe, because it is thick.
The pump may be clogged, but rarely, because there is an additional filter in front of it.
The drain hose only becomes clogged if you installed it incorrectly.
Check the drain, it may also be clogged. Disassemble the unit, pull out the pipe, loosen the clamps, rinse it. Pull out the pump by unscrewing the fasteners and disconnecting the sensors.
Signs of a pump failure:
Drain pump hums but water won't drain.
The machine may stop while the system is running.
Water flows out slowly.
Ariston washing machine pump repair should be done as follows:
If the filling valve is broken in Ariston, then water constantly flows into the washer, even when it is not working, it is disconnected from the network.
To check the fill valve, you need to unscrew the fasteners and remove the top cover. The valve is located where the drain hose connects to the housing of the electromechanical unit.
Check gaskets first. If they have not lost their performance, measure the resistance of the valve. Put the probes on the contacts of the filling valve and check the resistance if it is optimal (from 30 to 50 ohms).
If it is less or more than it should be, it means that the water intake valve is not working. To replace it, you need to unscrew the old valve from the body and screw in a new one. Be sure to connect the sensors.
If the heating element is faulty, then it must be replaced. Its breakdown is signaled by the fact that the water does not heat up or washing according to all programs takes place in cold water. Sometimes the machine gives an error and stops.
To replace the heating element, the rear wall must be removed. Under the tank there are two contacts with a fastener in the middle. This is the ten. Measure the resistance of the heating element with a multimeter.
If the resistance is within the normal range, then you do not need to change the heating element - it is serviceable. To remove the heating element, you need to unscrew the screw in the middle and pull it towards you with rocking movements.
The water may not heat up due to the fragile connection of the wires to the heating element, which arises from the strong vibration of the washer. Water heating may be absent even if the temperature sensor malfunctions.
Take a tester or multimeter and check the resistance of the sensor cold and hot. If the resistance is the same, then it is broken and needs to be replaced. The resistance must be different.
The high-quality and durable material from which the drum of household appliances is made also becomes unusable, because solid foreign objects get into it, which can damage the assembly, forming cracks on it.
The plastic rib inside the drum can be deformed. To replace the drum, you need to remove it.
To remove the drum yourself, you need the following set of tools:
a set of screwdrivers, especially a Phillips screwdriver and a slotted nozzle;
screwdriver;
pliers;
hammer;
hexagons of different sizes.
Using a Phillips screwdriver, the bolts are removed from the rear, front and top walls, and then the panels themselves are removed.
Remove the powder container. Remove the module with a slotted screwdriver. The control unit does not have to be unscrewed to the end, the main thing is that it does not interfere with removing the drum.
Remove the cuff of the hatch, pull out the lower bar by unscrewing the screws. From the loading tank, you need to dismantle the electronics, shock absorbers and other parts.
Remove the drum from the device and disassemble it. Remove the screws holding the two sides of the drum. Pry off the seals with a screwdriver and remove them.
In the drum, the bearing can break and wear out. It needs to be replaced. You only need to buy a bearing of the appropriate brand in a specialized store or order it on the official website of the Ariston washing machine, or purchase it at an equipment repair shop.
Use a metal rod and a hammer to knock out the bearings. If they are faulty, replace them. If the drum is deformed, then change it to a new one.
Reassemble. If the malfunction is in the plastic rib, then there is no need to disassemble the tank. The washer door is removed. A metal rod is taken, the diameter of which is smaller than the holes in the plastic rib of the drum.
The rod is inserted into one of the holes on the rib, the latch is opened with it, the plastic part is removed. A new plastic rib is put in its place. Move the plastic rib along the groove until the latch engages the hole and closes.
