Zelmer coffee maker 13z016 DIY repair

In detail: Zelmer 13z016 coffee maker DIY repair from a real master for the site my.housecope.com.

When incl. couple the same situation. It looks like the fluometer is clogged, but it is clean and rotates easily.

I think navryatli, so that she entered into such a stupor, "after which it turns off completely." although who knows. Is there a water sensor in the tank? I repeat the question, what about food, how is it done? How does the pump pump? Damn a lot of questions.

As you can see, the module is completely different here. And what springs are you interested in?

I could add firmware to this coffee maker, but the forum swears that it is forbidden to add a file with bin permission. Tried renaming to hex the same thing. A similar coffee maker was being repaired, I decided to merge it from the non-working firmware, but I can't add it to this topic.

Yeah. got it.

13z013.rar 110 Bytes Downloaded: 1510 times

The same coffee maker came to be repaired, the symptoms are the same (and I am mainly engaged in microwave ovens). What does this hall sensor look like and where to look.

This error means that no signals are received from the hall sensor located in the fluometer indicating that the fluometer turbine is rotating under the action of the water flow. that is, either the magnetite in the fluometer rusted, swelled up and jammed the impeller (disassemble the rust and give the fluometer a different life), or the magnet lost its magnetic properties (find and buy another magnet and change it)

either dirt got into the flow meter and jammed it, or there is another problem associated with the water flow meter (flow meter) that can solve the problem by replacing the flow meter with a new one. good luck.

remvad66, have you seen what is in the file? The controllers are locked in these coffee makers! And count them not

Video (click to play).

Image - Zelmer coffee maker 13z016 DIY repair

Dear meeting The Zelmer 13Z016 coffee maker got into repair after overvoltage, only backlighting of the display. Does not respond to buttons. Dismantled, removed the protective cover of the power supply and switching board. In more detail: the zener diodes Z4, Z3, Z2 have died if you can tell me the ratings and voltage on the 8th and 9th leg of the J1 connector. In a 9-leg chain, there is a capacity of 100mk * 50v. in a chain 8 legs 100mk * 35v. I am attaching a photo, if necessary, I can with a higher resolution. Best regards zolta

Dearshov244 Thank you. I painted the sketch for my opus and put it for viewing. I get that Z3 is 24V, and Z2 and Z3.

schema.rar 597.18 KB Downloaded: 1550 times

After two years of operation of Zelmer 13Z016, a periodic malfunction appeared when the button was pressed to brew coffee, the mugs started spinning and nothing happened, only turning it off and on helped. After another half a year, the following symptom appeared - when the coffee maker was turned on with the button, the screen began to light up and pentagrams appeared, after which the screen faded slightly and the pentagrams disappeared, when the buttons were pressed, the buzzer worked, but the coffee was not brewed. The reason turned out to be in the capacity of C4 (partial short circuit), it switched on the entire power supply. After the replacement, everything worked. Even when searching for a malfunction, the capacitance C2 instead of 0.47 microns, showed 0.31 microns, was replaced earlier, so I will not say how it affected.

A couple of questions for the specialists, how can you fill the fee. How relevant is this?

2015-05-31 15.33.33.jpg 157.66 KB Downloaded: 706 times
2015-05-31 15.34.14.jpg 158.27 KB Downloaded: 562 times

How to disassemble, check and repair a coffee maker.

In this video, I tried to embrace the immensity. Tell what it consists of, how it works, what and for what functions.

If you have any difficulties with disassembly, write.

Do-it-yourself disassembly and repair of the Zelmer coffee maker.

Repair of coffee machines - It's very simple! PS: I did not put the silicone gasket correctly, it is necessary.

How to check and repair a water meter (flowmeter)

How to eliminate overheating of a coffee maker.

Everything about the pump: disassembly, cleaning, lubrication, performance check.The operation of the valve is considered.

Basically I answered my customer :))

how to repair a coffee maker with your own hands.

What you need to know to repair a coffee maker.

I took the scheme here. A good video from this master on this and others.

I also want to recommend the service for the repair of coffee machines and coffee makers - Basics for the repair of coffee machines.

The announcement of the video about the repair of Zelmer 13Z013.

Features, PRICES, descriptions, reviews: Zelmer 13Z014 Red - zelmer 13z014-red.html Zelmer 13Z014 Braun.

A bunch of malfunctions in one coffee maker. The video is very close to a real repair. Also you can look.

What to do if the coffee maker takes a long time to brew coffee? Repair, device, principle of operation. Review electrically.

Drip tray cleaning, Descaling, Auto-off function - ZELMER Operating Instructions 13Z016

16. Auto power off function

The device will turn off automatically if left unused for one hour. To again
turn on the device, press the on / off button

(A), a beep sounds.

17. Cleansing the drip tray

When the drip tray (8) will be filled with water, the red indicator of its filling (9)
will rise above the grate (7)... Take out the whole set of drip tray from the express (8)
with lattice (7) and pour the water (Fig. 10)... Put everything back together on the express.

Limescale is a severe deposition of minerals that naturally appear in every appliance by boiling
water. Therefore, the coffee maker needs to be descaled from time to time. After using the coffee maker
a certain amount of water (the amount of this water is directly related to the hardness of the water selected

in the coffee maker), the flashing indicator appears on the display.

... Its appearance on the display indicates that

the user must carry out the descaling process using citric acid.

Important: For descaling, you need to prepare a special solution... Mix two spoons (approx. 30 grams)
citric acid v ONE liter of water.

18.1. Unplug the device from the network.
18.2. Make sure the coffee maker is cold.
18.3. Take off the drive for water (1) and drip tray (8) together with the lattice (7) from the coffee machine (Fig. 11).
18.4. Place the express upside down and remove the filter grill from the filter head (4) unscrewing the grate

with a screwdriver (Fig. 12).

18.5. Clean filter grill and filter head (4), remove limescale and coffee residues.
18.6. Place the express in position ready to go.
18.7. Fill the water tank (1) prepared solution with citric acid.
18.8. Close the lid of the water reservoir (1)and then install the drive (1) and drip tray (8) together

with lattice (7) back in the coffee maker (Rice. thirteen).

18.9. Connect the device to the mains by inserting the plug into the socket. The coffee maker switches on, the display and the button

(A) flash and the network indicator appears on the display

18.10. Press the on / off button

(A), A beep will sound.

18.11. Display pointer

starts to rotate, indicating that the espresso machine is warming up.

stops spinning, a beep will sound informing you that

the espresso machine is ready to use (warm enough).

18.13. Press and hold the button for selecting the amount of coffee at the same time

two seconds. The descaling indicator stops flashing

, but the pointer starts to rotate

informing that the descaling process has started.

18.14. From the steaming head (4) boiling water will begin to pour out along with the scale.
18.15. Wait for the solution to float through the steaming head (4)... Then take off and rinse

storage device (1) clean water.

18.16. Place an empty hopper under the steaming head (4)so that boiling water can collect there.
18.17. To carry out the cleaning step, pour clean water into the reservoir. (1) up to the MAX level marked on

water storage (1)... Close the drive cover (1), and then install the drive in the express.

18.18. From the steaming head (4) boiling water will come out (rinsing the device).
18.19. After the descaling process, boiling water will stop flowing through the steaming head (4),

and clients, as usual, do not remember when it began to leak, the explosion was not small if the iron bent

Thank you, as always everything is clear. I wish you successful repairs.

When will Bork be brought to you)

repaired, made coffee, rested)))

excellent renovation! they explained everything thoroughly. thank you! 🙂

As always, everything is at the highest level!

Good afternoon, and by what means do you decalcify, how do you feel about vinegar or citric acid

Hello Oleg! As always, you pleased us with a detailed and informative video, thank you) Tell me, is it possible for you to write a question somewhere on the video from the school of electronics channel? I would very much like to receive your advice, thanks in advance for your reply, all the best to you!

Great video. I'm already waiting for a video on the New Year's theme))

The hostess came to me and brought a coffee maker with her. for a hvist :)))))

Please make the screensaver quieter)

The scheme is like in a Chinese lantern.

Thanks for the detailed story and showing

The army of subscribers is growing, so you are doing everything right and interesting!

I am not very good at technique, but from watching your videos, a lot becomes clear to me. Therefore, I look forward to new videos! Thanks!

Good evening! What laboratory power supply do you use?

Good day . there is a delonghi 3500 machine. Already the rosberal coffee grinder, I missed everything. And all the same. Sometimes it makes coffee norms. and often writes a message to Lest coffee (Little coffee) and just throws aside what he has ground. but sometimes it will pour water in general. rustling kofem normally does, but sometimes it doesn’t make a weak one again. either write an error a little coffee

No oczywiście kciuk w górę. Oleg lubię oglądać Twoje filmiki. Nie ma dla Ciebie trudnych napraw. Skąd jesteś z Rosji czy z Ukrainy. Serdecznie pozdrawiam z Warszawy.

and you don't need to buy a coffee maker home as there is always work at work))))

UNCLE OLEG, THANKS FOR THE CONDENSER WAS INTERESTING.

Hello Oleg! Great video as always, thanks. The question is, what is the best way to waterproof the boards? If possible from the available means. Thanks again.

I sit without repairs. I miss. The people have no money, they ask for repairs on credit or a refusal. I wish YOU many good clients and successful renovations.

The coffee makers are already overpowered.
Nafig them.

repair in reality - everything seems to work and oops.

In this video, I tried to embrace the immensity. Tell what it consists of, how it works, what it is responsible for and for what functions. I hope this video will help a thoughtful repair and not only this coffee maker.

Basically I answered my customer :))

Disassembly, cleaning, repair of the VITEK VT-1513 coffee maker

Subscribe to Eco Plant to win an iPhone, Mac Book, and landscaping for 500,000 rubles! - Hi guys. Today we will make a simple and useful tool for cleaning car candles. This device restores candles from carbon deposits and extends their service life.

Walking down the street with my son, I found a board that looked like an amplifier or a radio, but with an inverted speaker. I didn't really need it, but the board had a very good transformer, and the speaker was with a magnet, so I decided to take it home. After a cursory examination, I decided to plug this device into an outlet and test it 🙂 For a long time I could not figure out what kind of device it was and was about to disassemble it in parts, suddenly. now I know what it was and what kind of KR1850BE48 microcircuit was at my disposal. My son liked this device so much that I decided to make a toy out of it 🙂 I have no goal to educate the growing up and enlighten the fading generations. The whole essence of what I am doing fits into the slogan “I live this way” placed on the title of my channel.

Welding small metal objects with a stylus and a transformer is possible, but not worth it. Of course it looks beautiful - sparks fly in all directions, it stinks of smoke, but there is little sense from such welding. To create thermocouples, I used this method of welding nichrome and copper wires, but even for cutting beer cans, this method is rather weak. How to do I showed what I was capable of criticizing, to repeat or not to repeat - it's up to you.Good luck to all! You can always repeat this and similar experiments at home. I do not use unusual and rare hard-to-find resources. And my whole "laboratory" fits on the kitchen table. I have no goal to educate the growing up and educate the fading generation.

Showed one of the repairs of the electric kettle

Cantalum or Euro fechral wire can be purchased at vaper shops. One meter of 0.7mm wire costs 5 rubles. This wire is better than nichrome and from this wire you can make an analogue of a hair dryer for soldering. The current consumption is 9-10A at a supply voltage of 5V.

Repair of coffee machines - It's very simple! PS: I did not put the silicone gasket correctly, you need the back side) and also, in order to clean it, you can not remove the horn holder. Ps 2: really, the taste of coffee has become just awesome. Earlier, after drinking a cup, there was heartburn and rying up, after cleaning there was no discomfort.

Shown design for disassembly and repair of capsule coffee maker KRUPS KP2106

Published by oleg pl 11 months ago
Search oleg pl

What you need to know to repair a coffee maker

LG TV backlight repair

Translated instructions are often very difficult to understand, even with experience with coffee machines. It's easier to see once than to read a hundred times 😉

Unboxing & presentation coffee machine from Lidl Model: SEMM 1470 A1

He showed how the hob is arranged, how it works and a little repair.

Hello everyone! A huge amount of work, videos and studies are exhausting, so to be in good shape - drink coffee! Today I will make delicious coffee for you!

Showed how to check and repair a food processor.

Owner's review about Espresso Coffee Maker ZELMER 13Z016 Subscribe to the channel! There will be more!

Basically I answered my customer :))

How to check and repair a charger

A bunch of malfunctions in one coffee maker. The video is very close to a real repair. You can also look at the repair of this coffee maker https://youtu.be/wxCtox6MJF8

Everything about the pump: disassembly, cleaning, lubrication, performance check. The operation of the relief valve and water filter is considered

Now it is difficult to repair these TVs in service centers. But in some cases, you can do it yourself.

Today our Zelmer Supremo coffee machine broke down. The essence of the breakdown is as follows - after pressing the manual coffee button (manual button), the machine works for a few seconds. Then it is simply cut down, all the buttons start blinking, and the machine itself beeps.

Well - you need to disassemble it. Disassembly starts - removing all containers from the machine. Next, from the bottom, unscrew the 3 fixing screws that secure the small cover. A water flow sensor or, as it is called, a fluometer is installed under this cover. It is these typical breakdowns that indicate that this unit is not working properly. A Hall sensor is attached to the flow meter.

The next step is to unscrew the water flow sensor, carefully remove the tubes. They are very difficult to film. Do not confuse which tube is attached to which connector.

After dismantling the pipes, you need to blow through the water flow sensor - this can be done, for example, with a pear. First we blow it with air, then with water. Using the same pear.

If everything is ok with the impeller inside the flow meter, the hall sensor is in working order, then such a repair should be enough. We check - carefully fasten the tubes in place and turn on the machine. If it does not help, you will have to look further. Remove the flowmeter again and disassemble it.

The lid is fastened with latches - and in order not to break them - you need to carefully slip hard thin plates under these latches and only then the lid will snap off.

The impeller is located under the cover. On which there is a magnet. On another part of the flow meter, you can see the Hall sensor, in which, most likely, the cause of the malfunction lies.

To pull out the sensor, you must use a hair dryer - it is glued to the body of the flow meter. Next, you need to inspect the sensor. Clean off glue residues and re-solder contacts. If it does not help, you need to change the Hall sensor.

Re-mounting the sensor must be done with hot melt glue. There are many options here and they all depend on how you succeed. You may even have to cut off a part of the case and then fill the space with hot melt glue and check how successful the repair was.

Functionality check is carried out using a tester and a magnet. We connect the tester to the red and yellow wires on the terminal block and turn on the machine. In a state of calm, it reads about 0.5 volts. When the magnet is brought up, it resets the voltage to 0. Next, we mount the impeller in place and turn it, observing how the voltage changes. If a reset to 0 occurs, go to the reverse installation of the entire flow meter and put it in place, remembering that you need not to confuse which tube to connect to.

We close the cover and mount the screws in place. After such a repair, your coffee machine is back in service.

How to disassemble, check and repair a coffee maker.

Do-it-yourself disassembly and repair of the Zelmer coffee maker.

In this video, I tried to embrace the immensity. Tell what it consists of, how it works, what and for what functions.

What you need to know to repair a coffee maker.

I took the scheme here. A good video from this master on this and others.

If you have any difficulties with disassembly, write.

The announcement of the video about the repair of Zelmer 13Z013.

Zelmer 13Z016 coffee maker Does not work stably, leaks. Repair .

Everything about the pump: disassembly, cleaning, lubrication, performance check. The operation of the valve is considered.

how to repair a coffee maker with your own hands.

Online store "Triton-online" t.0382 783-777 t.098 17 54 555 t.093 33 51 000.

How to check and repair a water meter (flowmeter)

Repair of coffee machines - It's very simple! PS: I did not put the silicone gasket correctly, it is necessary.

I also want to recommend the service for the repair of coffee machines and coffee makers - Basics for the repair of coffee machines.

A bunch of malfunctions in one coffee maker. The video is very close to a real repair. Also you can look.

Basically I answered my customer :))

Disassembly, cleaning, repair of the VITEK VT-1513 coffee maker

Video uploaded by oleg pl
Search oleg pl 3 years ago

How to check and repair a water meter (flowmeter)

Read also: DIY sea repair

Good afternoon, tell me please, my coffee maker does not add coffee, I put it at 60, it pours 30 grams, I put it at 30, it pours 20. You have to use only software fillingHello, tell me what to do, I turn on the water flows from under the car. I gave it to my city for repairs - they said that the pipeline was leaking. I waited half a year and did not wait, what to do?Good day! I have a Roventa ES6200, when making coffee, the machine works intermittently, sometimes it just turns off, or continues to work when turned off. The service said that it was the control board that died. For the replacement of the board they asked for more money than the cost of the machine itself. Please help with repairs or where you can buy a board at an adequate price. Thank you.Is it possible to see videos on the construction and repair of more serious and expensive household coffee machines? For example: Melita Barista T; Krups EA8808; Melita CI; Bosch 60729; Delongy Diva Elite; Hajia Academy or Saeko Exprelia.Hello . Didn't you find anything in the coffee machine repair playlist? The principle of operation and repair remains unchanged. The biggest changes are in electronics and displays. For repairs, the main thing is to understand the principle of operation of units and individual elements (which, in principle, I want to convey to the viewer) Good luck.everything works - the boiler does not heat, cold water is running ((Tell me, what is the voltage coming from the boiler relay?Oleg, thank you for your review. I have the following problem with this device - the pressure is released only after turning the power on and off. Those. one cup is brewed, the piston remains in the fully extended position. When the power is turned off, the relay clicks after restarting, the pressure is released, the rest of the water is drained into the bath, the piston returns to its place. Where to dig, what to change, tell me, please.Good afternoon. The same coffee maker stopped making the second coffee. Does only after turning it off and on again.The symptoms are as follows - after the first cup, the information on the display goes out for half a second (while the backlight is on) and coffee continues to drip from the horn. The feeling that the piston pressing on the horn does not return to its original position. The second cup of coffee just causes endless waiting and the rotation of the mug on the scoreboard. Only after restarting the machine drains water into the receiver, it sounds like the piston rises to the upper position and the machine can cook again. I suspect that the problem is in the solenoid valve. Collided? What could be the problem? There are basic skills of a solder. What can you tell me?Hello. They sent the coffee maker for repair and returned it with a new, as I was told, "power unit". It can be seen that the display has been replaced, and the filling behind it. The second day, the flight is normal.I wrote my question, then I saw yours. Same problem. I looked at the valve, disassembled it, mine is clean inside, there is no scale, it is free to move. The relay clicks clearly. I understand that there is no command to open the valve.The Zelmer 13z016 coffee maker, after turning on the network, the pump turns on, the water comes out through the thermoblock, I did not notice the discharge of water into the droplet receiver, then everything turns off. After turning on for making coffee, the screen glows to the floor, the circle spins, but nothing happens further. Can you help determine the reason for this behavior of the coffee maker.? By the way, without waiting for the normal operation of the coffee maker, I tried to turn on the descaling mode - everything works, only at the beginning there is cold water.Hello! Tell me how the horn disassembles in this coffee maker. I've been twisting for a week, but I can't figure out how to do it.already disassembled)))) read in the comments. Thank you for the vidos.Good health! Thank you for your work and this video. With your help I am trying to fix my device. I have a different Zelmer coffee maker, but the board with the batteries is the same as the 13z016. I measured everything according to your instructions - at the output from the diode bridge it turned out to be 9.5 volts - I bought a new kander 0.47 microfarads - changed it - it became 11.6 volts. Tell me where to look and how to solve this problem. Thank you.can you name the numbers and names of the condensers?repaired. diode bridge and two canders.Hello, please tell me, the coffee maker does not dispense water during operation. I turned it on and no matter how many cups you choose, the water flows and flows. It started with the fact that the water stopped flowing, I thought something with the pump valves, I disassembled it using your video. In general, the tubes are just thin after the boiler is overgrown with scale - cleaned. Without twisting the screws - for a living - I brewed a cup of coffee, a portion of water poured out and the machine turned off. I twisted it with screws, turned it on, and it started, heats up the water, turn it on for one cup, and the water supply does not stop until the water runs out, and a relay clicks twice, once quietly, the second time louder. Is the flow meter responsible for this? Tell me where to look.The problem is somewhere on the control board .. a triac or an element controlling it .. alas, without seeing and making measurements, it is difficult to make an accurate diagnosis. maybe right down to the power supply.Hello, please tell me, such a problem has arisen, the cappuccinator stopped whipping milk as it was at the beginning of use and later completely stopped whipping, how to solve this problem? I will be grateful for the answer!but I have hot air or steam blowing out of it as it will be more correct, but there is no pressure and the foam does not go astray as it should be. It will probably also be necessary to disassemble it again, I took it apart for the first time in order to fix the bag with a collar, since the water was discharged straight on the table on which the coffee maker stoodthe hose of the cappuccino maker inside the machine may have burst. I had such that when I turn on the cappuccinatore, there is zero reaction. I disassembled the coffee maker, checked the hose that goes to the cappuccinatore and it turned out to be burst (most likely from the hot water that flows through it)no, it didn’t work, unfortunately, I don’t use it for a long time, I just make coffeeAlexander, did you manage to defeat the cappuccino maker? At first, too, everything seemed to work, and then when it was needed this thing stopped working. The tube seems to be clean.I think we need to disassemble and purge this case, it will be clear where the blockage is.Yes .. but there might be a problem with the tempurature.Good afternoon, tell me the problem in the Zelmer 13z016 machine, after a year of work in our "reliable networks" when the voltage jumps from 170 to 240, the machine starts up only at a voltage of 238V and above, everything below it turns on as it should, BUT freezes at the stage warming up (the mug is spinning) and that's it! As soon as the voltage is too high, it works without problems (the mug disappears), although after that the steam supply only works normally 10 times. We can say that the steam supply was also disrupted, before the steam was stable, but now (in cases of start-up) it gives out steam in the first 10 seconds, and then decreases until the steam supply is completely stopped. And so 10 times after on, off, it can give off steam more or less stably. You, as a specialist in these machines, your version of why this is happening, and how to solve this problem. What to check and what to change !?I think the problem was not there. There is a capacitive resistor power supply. Or rather, the voltage is extinguished by a large yellow capacitor (if I remember correctly 0.047 microfarads 400-500 V), so over time it loses its capacity and its resistance becomes larger. The first thing I do is just solder it and measure the capacity, in 90 cases out of 100 it is less than necessary. You just increased the pressure to 238 V and after that the relay received the necessary 22-24 V to operate on the relay. Check the condender, this is their constant sore.

After numerous "" tips "")), I had to introduce myself into the principle of operation of my favorite coffee machine! Two days without a rash, and yet the problem was found. The fault of the relay 899-1A-f-ce (24V), which is responsible for supplying voltage to the boiler! (It worked, but did not hold, immediately released the contact). After prolonged, apparently operation, the mechanics of the relay began to glitch, therefore it worked only after an increase in voltage, and even then not always! All of the above problems were from this! Since I had not yet found the same relay in Ukraine, I had to disassemble the relyushka, bend the plate, and everything began to work like a watch, though I don’t think that for a long time, but the problem was temporarily solved!The problem with plump and skills does not exist, since all my life I have been holding a soldering iron in my hands))) And I have a higher education in radio engineering))) I want to hear from you a possible reason. I've assembled and disassembled it a thousand times already. I asked you a question, because you know more the principle of this machine. And to save time, I would like to ask you as a specialist what you say! ATP for your understanding!Hello! Alas, without owning a soldering iron and mechanical skills (disassemble and assemble), this problem cannot be solved on your own 🙂 All the tips are given in this video.It is very IMPORTANT to show the entire process, namely the disassembly and assembly of the infuser sieve. Since there is a spring and some kind of valve. Now, if they are not put correctly, there may be problems. You are posting a video to help figure it out.Thank you for your understanding and your work.Understood ! I will take into account the remark in further videos. It's just when you often take pictures of similar coffee makers. it seems that he has already told about it. Thanks for the comment !Tell me how you can disassemble and clean the 13z016 Zelmer horn. I can't drink coffee. Water always remains in the cone, there is no coffee crema. Grateful in advancethe same question! it is very necessary to disassemble, help!+ Ivan Nastenko Thank you for your comment !! I never reached my friends to look at the horn: ((+ Sergey Didenko I have it (my friends have 016) I will look.Oleg tell me how to clean the boiler on this coffee machine? clogged.+ Alexander Lysogor Yes, most likely a stainless spiral tube. I didn’t break it, but I was digging around with one for a couple of days. I even had to drill a little (on a straight line).It is packed tightly. Tell me how does it look inside? spiral or otherwiseThe procedure is not simple .. depending on how much it is packed.We remove the tubes from the boiler (purge) Next, prepare a solution of lemon (half a glass of warm water per tablespoon of acid), take a syringe and pour a little into the tubes of the boiler. you can help a little with steel wire. After we have broken through the cork at least a little, we do decalcification. Good luck .You have to drink a lot of coffee with these repairs :))) I have jura f70 weak steam pressure from the cappuccinatore, washed everything, even replaced the pump !! What could be the cause of the breakdown?+ Vadim Shukaev Yes, sometimes you have to pour it out. flavored coffee. Well, if there are no friends nearby: - ((+ oleg pl I always do it, the machine automatically asks for it after a certain number of cups, I will disassemble everything now and blow it according to your instructions, I did not do that! All washes were automatic! It feels like you really partially clog the cappuccino maker! In any case, thanks for your video training helped a lot, you explain everything in an accessible and understandable way! With the use of coffee, be careful, it is not recommended to use a lot!+ Vadim Shukaev It is difficult to tell .. maybe a weak heating of the boiler .. Did you really do decalcification?+ oleg pl the water passes, but there is no steam pressure as it was before, the milk foam is very thin on the surface and does not retain sugar!First sensation. This is a clogged valve on the cappuccino maker, if water does not pass through it well.Good day. The machine reports limescale. The cleaning seems to turn on, judging by the indicators, it hums, but the acidic water does not come out. Moreover, it is buzzing for about 20 minutes, probably. Then there was a long pause - and again. What could it be? Thanks!+ nomadualand Hello. If the pump works and the water does not come out, then the scale has clogged the water path somewhere. Here, unfortunately, you can't do without disassembling the coffee maker .. here's a quick shot of one of my videos on this issue (the coffee maker is not yours)HAPPY HOLIDAYS YOU.+ Sergey Kartukov Thank you very much! You too ! Have a good spring mood and good luck in your work and life.Triac, he is also a thyristor. And how does the car know that it’s time to decalcify it.+ Take a look at your machine counts the portions of coffee and as soon as you decide to drink one extra. immediately begins to swear 😉 The number of cups is determined by the density of the water (which, in theory, we should measure and set). Good luck .Thanks for the video, I remember a little bit of electrical engineering, nostalgia.+ oleg pl From something straight hooked with nostalgia your message. I can't help remembering. I didn’t consider electruha to be unnecessary at the University - it was just that our teacher didn’t really like me, or maybe he thought that I “can, but I don’t want to,” and constantly made life more difficult for me. And I chose more difficult tasks, and I several of them. days decided. Moreover, I remember how I turned to other professors of the department for help and they decided for me. wrong)) In the end I decided on my own, and then I defended myself for 2-3 lessons. Well, and in the end, for 15 years, I have not touched this in any way. And then I started vending) I bought a couple of machines, then another. well, I had to remember my teacher with a kind word. Thanks to him. Yes, but I forgot a lot during this time, if not 70-80%, but that base still helped a lot. Of course, I don’t know many things yet, especially electronics, but life forced me to work) That's just a multimeter burned down. I put the wire on the dial and looked for it, but it was energized and .. bam. We need to figure it out - it's buggy now))+ Alex Yea Wow .. if you only knew .. your humble servant (tobish I) considered electrical engineering the most stupid and unnecessary subject. But life so ordered .. that for many years it became my main job (well, how I did not try to avoid it.). Army .. power engineer of the receiving radio center near Moscow. After the army (hurray !! controller of radio equipment), then again an electrician. and so on until today. I am very sorry that I did not listen to my teacher in electrical engineering (I even remembered connecting electric motors more than once (of course I heard about rough pieces of iron ;-)) Thank you for your comment! Good luck .