Details: lg direct drive 6kg DIY repair from a real master for the site my.housecope.com.
Many people use washing machines nowadays, which is absolutely not surprising, since it is washing machines that allow us to keep our clothes clean. However, sometimes these devices can break for a variety of reasons and when this happens it can bring us a lot of inconvenience. If you do not want to endure such inconveniences and want to bring your technique back to life as soon as possible, then repair of lg direct drive washing machines , in our company is the perfect solution for you.
Washing machines of the lg direct drive line are very popular in the household appliance market. The reasons for this are quite obvious, they have very good technical characteristics and are also very durable. That is why many consumers choose them.
But, like all other equipment, washing machines of this line are not protected from any malfunctions in their work. And if such problems arise, then repair of lg direct drive washing machines in our company is the most correct solution in this situation.
Major breakdowns of lg direct drive washing machines
Washing machines of the lg direct drive line, as you might guess, have their own design features. They largely determine their advantages, but also contribute to the most common breakdowns. Among the most common breakdowns of these devices, it should be noted:
To effectively deal with dirt on clothes, the washing machine uses hot water. That is why, it is endowed with a special function of heating water. Sometimes this function can break down in it, and the reasons for this most often lie in problems with the heating element. In most cases, it is necessary to change the heating element, after which the washing machine starts to successfully heat the water again.
Video (click to play).
If you are facing such a problem then
repair of lg direct drive 4kg washing machines in our company can be just an excellent solution for you, as our specialists will be able to deal with this problem very quickly and efficiently.
Should you try to turn on the washing machine? You cannot do this, while it is connected to the electrical network, most likely there are some problems with the control unit. It should be noted that problems with the control unit are always very unpleasant, since this is a very serious breakdown. However, if you decide to order repair of lg direct drive 5kg washing machines in our company, then our masters will be able to quickly solve this problem.
Problems with draining water in washing machines are quite common. The most common cause of such problems is a malfunction or a clogged drain pump filter.
In any case, this problem is quite solvable, especially if you use such a service from our company as repair of lg direct drive 5kg washing machines .
- The smell of burning from the washing machine
If you smell a burning smell from the washing machine, you need to unplug it as soon as possible. The reason for this smell is most often a short circuit, which poses a very great threat to the washing machine. After you disconnect it from the power supply, you need to call our specialists, that is, use our service repair of lg direct drive 6kg washing machines .
LG direct drive washing machines are in high demand among customers. The new design made it possible to significantly increase the engine resource, while the SM belongs to the affordable price segment.
But even such equipment is subject to breakdowns, and maintenance of LG washing machines in a service center is sometimes expensive.Therefore, we will tell you about the typical malfunctions of this brand and the possibilities of self-repair.
According to statistics, breakdowns of direct drive LJ washing machines occur after five years of operation. To understand where to start troubleshooting, let's look at how a direct-drive CM and a standard machine work.
Look at the diagram of the LG washing machine:
In the first case, the drum is rotated using a drive belt. In the second, the drum rotates the motor directly. Such a motor also does not have brushes that constantly wear out. In the event of a breakdown, you will immediately determine that the reason is in the motor, and not in the parts adjacent to it.
We have disassembled the principle of operation, now we will consider which nodes most often fail:
How can a user know where exactly the LG washing machine has broken down? For this, there is a self-diagnosis system. If a problem is detected, the system displays the EJ error codes on the display.
You just have to decipher the code and find the problem.
One of the best helpers in the house is the washing machine. It facilitates the work of a woman, frees her at least from washing. If the family is large, then you have to wash every day to keep the apartment clean and the hygiene of its residents. Therefore, the breakdown of the washing machine is a real problem for a woman.
The entire wash is a heavy burden on her shoulders. And the hostess begins to wash all this linen and clothes by hand, wasting time and energy. And so every day, dreaming about a new washing machine or about how to quickly repair an old one. And there is no money for repairs.
What then is to be done? It is necessary to somehow get out of the situation. If the husband is with hands and head, then he will be able to independently find the cause of the breakdown and replace the faulty part with a new one. Today we will tell you about how to disassemble the Lg washing machine and any other model.
The brands of machines differ from each other in some peculiarities: washing programs, sizes, number of revolutions, but the principle of disassembling washing machines is the same.
For high-quality and quick disassembly, you need:
two screwdrivers, a thin flat and a Phillips screwdriver for unscrewing the fasteners;
round nose pliers or pliers;
awl;
hammer;
open-end and socket wrenches;
ticks;
nippers.
The internal parts of the device are protected from negative environmental influences by metal elements of the case: back wall, front panel, top cover.
To do this, lay the device on its side and remove the pump through the bottom, having previously disconnected the wires from it. To remove the drain pump, you need to loosen the screws and disconnect the clamps. To do this, press the latches with pliers and disconnect the drain hose and the pipe.
You need to disassemble the pump from the snail by unscrewing the screws on it. Remove dirt and mucus from the snail.
Pay attention to the impeller, rotate it on the shaft, whether it turns, whether it is damaged. If it is broken, replace the impeller with a new one.
Also check the rubber seals. If the gasket is cracked or torn, replace it. Next, pry the latch with a screwdriver and remove the motor from the coil. Remove the monolithic cross by warming it up with a construction hairdryer. Then pull the magnet off the shaft.
After that, clean all parts of the pump, remove dirt, check the bearing. Lubricate it. If broken, replace. Begin reassembly using the photograph taken before disassembling the drain pump.
VIDEO So, we have removed all panels: front, back and top covers, control module. We will now show you how to disassemble the loading tank of the Lg direct drive washing machine.
This work in the service center is the most expensive, because the machine must be completely disassembled. The bearing and oil seal are located at the rear of the tank. To find out if the bearing is defective or okay, rotate the drum by hand.
If you hear a creak and hum, then the bearing does not work, it must be replaced.
As soon as you buy Lg, you immediately need to install the washing machine on a flat surface, adjusting it in level so that there is an even load on the bearings.If you see a leak in the back of the tank, then the oil seal has become unusable.
To get to the bearing, you need to completely disassemble the drum. You need to replace the part with a new one of this particular model. You cannot take a bearing from other machines, because it will not fit. When buying it in a store, pay attention to the integrity and quality of the part.
Direct Drive, or Direct Drive, is a new technology used by the Korean firm Lg. Thanks to it, the life of the washing machine is longer, because it does not have a drive belt.
The machine is quiet. In washing devices of this brand, the motor is located at the back of the loading tank, and not at the bottom, like in other devices.
We told you how to disassemble the loading tank in order to replace bearings and oil seals, how to remove the drain pump from the washing machine, disassemble and clean it. Now you know how to repair the device so as not to pay a lot of money for a complete disassembly of the machine and its restoration.
VIDEO
VIDEO
The South Korean company LG produces wonderful direct drive washers. The use of this technology contributes to an increase in the working life of the motor and moving elements. But at the same time it cannot be said that the construction is completely “indestructible”. It has its own specific breakdowns. In this article, we will consider possible malfunctions and how to fix them. Some require a call from a specialist. And sometimes it is possible to repair an LG washing machine with your own hands: replacing a bearing, for example.
According to experts, all the details of this brand's washing machine are quite durable. The engine of the device is especially reliable. If it fails, then the cause of the malfunction is most often a factory defect. The “weak link” of the LG washing unit are:
Heating element.
Bearings.
Pressostat.
Terminals, wires.
Filling valve.
Water drain pump.
These malfunctions are manifested by various symptoms. It is only important to analyze them correctly in order to accurately diagnose the home assistant. So, these are the signs:
Important! Before you start repairing your LG direct drive washing machine, take a closer look at the unit's operation at all stages of washing the laundry. Do not forget to study the instructions in advance, and also find out about the warranty repair of the washing machine. Any deviation from the norm is a reason to be on your guard.
To provide access to the heating element:
Unscrew the fasteners that hold the back of the washer.
Dismantle this wall.
Pay attention to the bottom of the container. There are 2 paired contacts with a center screw. This is the heating element mount. Check the contacts with a multimeter.
Important! If the resistance value does not exceed 20 ohms, then the heating element is considered faulty.
Removing the heating element is easy. Unscrew the screw, and prying the rubber seal, remove the heating element. You can immediately evaluate the health of the heating element. Dark spots are clearly visible on the defective part. Often, breakdown occurs due to the accumulation of scale. The causes of breakdown also include water that got on the contacts, or power surges in the network.
It is impossible to repair the heating element: it can only be replaced by purchasing a branded spare part from the manufacturer. When installing, do not forget about installing the sealing rubber. To make it sit better in its place, lubricate it with machine oil.
Important! If the sealing rubber sits loosely in the hole, water will seep onto the contacts of the heating element, and it will burn out rather quickly.
Repair of electrical breakdowns begins with checking the health of all wires. Checking can be visual and with a multimeter. All defective terminals and wiring must be replaced immediately.
If there is a problem with the priming valve, proceed in this order:
Unplug the washing machine. Rotate it 180 degrees.
Shut off the water supply to the machine.
Unscrew the hose through which the water enters the tank.
Pull out the filler valve filter. It is possible that it is clogged.
If the filter is OK, disconnect the valve.To do this, unscrew the screws holding it in place.
Check the rubber bands on the valve. Most of the faults are associated with them. Replace the rubber bands if necessary.
If everything is normal with the rubber bands, then the control valve electrician is faulty. In this case, it cannot be repaired. You just need to replace it.
You can provide access to the drain pump without disassembling the machine. Just lay it on its side. You can reach the pump through the bottom. First of all, check the pump sensors with a multimeter. If the sensors are working properly, then the problem is in the pump itself. Now proceed according to the algorithm:
Remove the bottom of the washer panel (front).
Unscrew the fasteners holding the pump.
Substitute a bowl, as residual water flows out of the washer when you remove the pump.
Disconnect the plugs, remove the wires together with the indicator.
Disconnect the pipes, drain the water. Place the pump aside.
Important! Remove the detergent drawer before turning the washer on its side. This is necessary so that the remaining water in the compartment does not damage the control unit by spilling onto the electronics.
It is advisable to have the drain pump assigned to a specialist for testing and repair. Only a master can tell if the drain pump needs to be repaired or if a new one needs to be purchased. The assembly of the unit is carried out in the reverse order.
One of the most common do-it-yourself LG washing machine repairs is bearing replacement. If a bearing is found to be faulty, repairs must be made immediately, as loose parts can damage the tank. Then you will have an even more time-consuming and expensive repair. Let's consider this type of repair in more detail.
To work you will need:
Hammer with metal handle and bronze striking part.
WD-40 lubricating fluid.
Screwdrivers - flat and Phillips.
Pliers.
Keys - open-end and adjustable.
Automotive sealant.
Metal hairpin 40 mm long.
Before reaching the bearings, the housing must be dismantled. For this:
Remove the top cover first, followed by the top and bottom panels.
To remove the top cover, remove the fasteners that are located at the back wall.
After the screws are removed, the cover can be easily removed.
After that, removing the powder compartment and unscrewing the fastening screw, remove the top panel.
Disconnect all wires that connect the top panel to all electrical units of the washing machine.
As for the bottom panel, it can be removed in a slightly different way, since it is fixed with latches. In this case, you need to disconnect a special rubber cuff.
Carry out further dismantling in the following order:
Filler valve mountings.
Drain pipe.
Heating element wires.
Motor wires.
Priming pump wiring.
Upper and lower counterweights.
Branch pipe from the water level indicator.
Shock absorber mountings.
Important! After you have removed all the listed parts, the tank can be easily removed. It is advisable to do this work with an assistant.
The tank in the LG washing machine consists of two halves, interconnected with latches or screws. After you divide the tank into 2 halves, the drum pulley and its mounting are exposed. This mount must be removed.
Important! It often happens that some of the bolts do not loosen, even if you make an effort. In this case, WD-40 grease helps well. Apply it to the mount, wait 10-15 minutes and try dismantling again.
After unscrewing the pulley fastener, pull out the pulley, and screw the bolt back into place. This makes it possible to remove the drum without damaging the shaft. Place a metal stud on the screwed-in bolt and hit it with a hammer (very carefully!). The task is to knock out the shaft without damaging it.
Important! You cannot forcefully hit the hairpin with a hammer, since this is fraught with another repair, by the way, very difficult.
Assess how worn the shaft is. If there is even a slight play between the bearing and the shaft, the shaft can be replaced.
The next stage is the replacement of oil seals and bearings.Bearings should be repaired with the utmost care, hitting the opposite edge with a small hammer. Apply light blows until the damaged bearing pops out. It remains only to replace it with a new one and reassemble it in the reverse order.
Important! The seat for the new bearing must be perfectly clean.
If you decide on such a difficult task as replacing bearings (and maybe at the same time the shaft) in an LG washing machine, try to avoid typical mistakes that inexperienced craftsmen make:
Broken wires of the hatch lock indicator when dismantling the front wall.
Ruptured rubber cuff when trying to pull it out. This is because the clamp has not been removed.
Damage to the pulley when trying to dismantle it from the axle.
Breakage of stuck bolts from excessive applied force, without the use of special lubricant.
Tear off the wires of the thermal indicator.
Tearing off the filler pipe and hose at the same time.
Inaccurate pressing out of bearings with strong impacts. As a result, the drum is damaged.
If you did not manage to fix the breakdown, and you are thinking about buying a new household appliance, then to make it easier for you to choose a model, check out our rating of washing machines for quality and reliability.
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
Repairing an LG direct drive washing machine is a completely solvable issue. But, if the task seems too difficult for you, contact the wizard. Prompt and high-quality repairs without unnecessary adventures are guaranteed to you.
Experts from the world's leading service centers note the relatively high reliability of LG washing machines. The most "tenacious" unit of this machine is considered to be the engine, which breaks down only in one case out of 500 calls to service centers, and then in half of the cases, the cause of the module malfunction is a factory defect. Moving elements are also considered to be quite reliable, except for bearings, they are repaired more often.
What units of the LG washing machine break down most often? Let's list them:
a heating element;
pressure switch;
bearings;
wires and terminals;
drain pump;
filling valve.
Malfunctions of these most important units of the washing machine manifest themselves in different ways. It is necessary to carefully analyze the "symptoms" in order to more or less accurately diagnose the problem of the module even before disassembling the "home assistant". In particular.
Note! When diagnosing faults in the washing machine with your own hands, be sure to listen and take a closer look at its work at the stages of washing, rinsing, spinning and draining. In addition, read the user manual, any deviations from the norm should alert you.
To get to the heating element of the washing machine, you need to unscrew several fasteners that hold the back wall of the LG washing machine by yourself, and then dismantle this wall. Next, you need to pay attention to the lower part of the tank (near the very bottom). Two paired contacts with a screw in the middle should stick out from there, to which several wires go - this is the ten. We check the contacts with a multimeter, if its display shows a value less than 20 Ohm - the ten is faulty.
Removing the ten is easy. We unscrew the screw mentioned by us with our own hands, pry on the sealing rubber with a screwdriver and pull out the heating element from the bowels of the tank. We visually check the status of the module. Burnt teng rarely does not have visually noticeable damage (usually these are burnt spots). In most cases, the heating element breaks down due to a layer of scale that settles on it.Also, a breakdown can be provoked by a voltage drop or water that gets on the contacts. The video guide will help you to correctly remove the ten.
Repair of this module of the LG washing machine is not possible, only replacement. It is necessary to purchase an original spare part from the manufacturer and install it in the tank of the washing machine, not forgetting to install the sealing rubber. In the process of installing the heating element, you need to be most careful about the sealing rubber of the heating element. To make it sit better in place, you need to lubricate it with a small amount of machine oil.
Important! If the sealing rubber of the heating element sits loosely in the bore hole, water from the tank will seep onto the contacts of the heating element and it will most likely burn out again in the near future. Be careful.
VIDEO
Washing machine electrical repair LG boils down to checking all the wires and terminals coming from the control module to all of its units. It's not just about checking all the wiring with a multimeter - it goes without saying. It is also necessary to carry out a visual check: torn clamps, fragments of wires without insulation, traces of burning and melting of contacts. All wiring problems that can be detected during the check must be resolved by replacing damaged conductors and terminals - this is the repair of the electrician.
It is not difficult to diagnose faults in the filler valve of an LG washing machine on your own, and it will not be difficult to repair this module with your own hands, if you act methodically, according to a pre-planned plan. Dismantling and replacing the filler valve with your own hands is carried out in the following order.
Unroll the washing machine.
The inlet hose, which is connected at one end to the water supply, with the other end is screwed to the filling valve. We turn off the cold water supply by turning off the tap.
We unscrew the inlet hose.
We take out, check and clean the filter of the inlet valve, it may be clogged with dirt and the water does not pass.
If everything is in order with the filter, remove the top cover of the washing machine, unscrew the two screws holding the valve, disconnect it from the pipes.
Next, we need to check the rubber bands of the valve, in 90% of cases the problem is their wear and the inability to retain water in the future. If so, change the rubber bands.
If it's not about the rubber bands, then most likely the problem is in the control electrics of the valve. In this case, the entire valve must be replaced.
Before the drain pump of the washing machine LG can be reached without even disassembling it. You just need to tilt the machine on its side, after that it will be possible to get close to the unit through the bottom. We check the drain pump sensor with a multimeter, if everything is in order, then the problem is in the unit itself. Next, we proceed in order.
Unscrew the lower part of the front panel of the machine.
We unscrew the fasteners securing the drain pump.
We substitute the basin, since water will flow from the unit during removal.
Disconnect the plugs and remove the wires with the sensor.
Disconnect the pipes, drain the water and remove the unit to the side.
Note! Before placing the clipper on its side, remove the powder cuvette as directed by the user manual, as water remaining in the cuvette may spill onto the control box and damage the electronics.
Once the drain pump has been removed, it is best to have it checked and repaired by a specialist. Only he can finally say whether the pump has really come to an end, if so, then you need to buy and install a new one. Assembly is carried out upside-down. The easiest way is to change the pressure switch (water level sensor) of the washing machine. If you manage to disassemble it correctly, then it will not be difficult to replace it yourself.
Bearing failures are a matter of time or a factory defect. The user can influence this process only by the intensity of the use of the home assistant. Bearing malfunctions must be repaired immediately, because if this is not done, the loose pulley can damage the tank and then repairs will be very expensive. In this case, the user manual will not help; you either need to contact a specialist or study specialized information.
Thanks to direct drive technology, which is implemented on most models of washing machines from the company LG, bearings, motor, pulley and other parts wear out much more slowly and last longer. Nevertheless, there are still cases of bearing failure, and this poses a problem for “self-repair lovers”. Not everyone knows how to properly remove the bearing from the drum, but to start doing this, you need to remove and disassemble the washing machine tank.
Bearing repairs must be done very carefully, using a special hammer with a bronze bump and a thin metal rod. It is necessary to pull out the bearing by striking its opposite edges. First, we put the rod on one edge of the bearing and strike it lightly with a hammer, then we transfer the rod to the other edge and again strike it lightly. The procedure must be repeated until the old bearing pops out, then a new bearing can be put in its place.
In conclusion, we note that malfunctions of any module of the LG washing machine, you can try to fix it. Of course, even if you study the relevant technical information and expert advice, successful repairs are not guaranteed, but it is definitely worth trying, especially since in most cases you have to deal with typical breakdowns. If something doesn't work, you can read the washing machine repair manual.
VIDEO
Any home appliance is prone to malfunctions for one reason or another. And washing machines are no exception.
The most common breakdowns of automatic washing machines (AFM) include:
Failure of the drum to rotate;
Stopping the discharge of waste, dirty water from the tank;
Increase in time for the standard wash cycle;
Failure of the heating element of the unit;
The machine refuses to draw water;
The drum of the washing machine rattles when rotating, emits extraneous noises and rattles.
In our article, we will analyze the repair of two devices that are directly related to the above malfunctions. Namely: we will tell you about the repair of the pump of the LG washing machine with our own hands and how to replace the bearing in the AFM LG F1068LD and F1022NDR.
Despite the fact that modern machines for washing dirty things are equipped with all kinds of electronics as much as possible, according to average statistics, most of the malfunctions (more than 75 percent) of these devices are in the mechanical units and parts. To be honest to the end, let's say that according to the information of all the same statistics, the main fault for the untimely (before the expiration of the warranty period) failure of the automatic machine lies with their users and is explained by the improper operation of this device.
A sure sign that the bearing of the washing machine needs to be replaced is the appearance of a grinding noise and similar noises when the AFM is operating at high speeds in the spinning or washing mode.
The process of replacing a bearing device cannot be called technically difficult, but the fact that this task is quite troublesome and time-consuming is for sure. Before proceeding with the repair of malfunctions (bearing) of the LG washing machine with your own hands, you should, based on the model of the machine, purchase it. Bearings 6205 ZZ and 6206 ZZ are designed for LG F1068LD and F1022NDR machines.
Materials and tools needed to repair (replace) bearings:
WD-40 grease;
Sealant, can be automobile;
A set of screwdrivers with ends of different shapes;
Pliers;
Hammer;
A set of open-end wrenches and caps;
Adjustable wrench;
Metal pin about 35 centimeters long.
The essence of the preliminary disassembly of an automatic washing machine of the LG brand is to sequentially remove it:
top cover and upper dashboard - both parts are held in place with self-tapping screws;
bottom front panel - fastened with latches.
After completing the above operations, you will provide yourself with free (relatively) access to the tank of the device.
We release the AFM drum from the connected devices in the following sequence:
We disconnect all the electric wires of the electric heating element (TEN), the filling pump and the electric motor.
A branch pipe designed to drain the liquid.
Branch pipe with water level sensor.
Upper and lower drum counterweights.
Dismantling the tank and replacing the bearing
We divide the washing machine tank into two component parts, thereby gaining access to its drive pulley and the fastening that holds it.
We release the screw that secures the pulley.
We remove the pulley, while inserting the bolt back.
Putting a metal pin (hairpin) to the head of the bolt, knock out the shaft with the adapter sleeve with light blows on it with a hammer.
After removal, we inspect for external mechanical damage.
We scroll the shaft on the bearing.
If vibration (backlash) is detected, we change the bearings and ASM oil seals.
We knock out the oil seal from the hole in the back of the drum (in the middle).
We carry out the same actions in relation to the bearing.
We clean the hole from old grease and debris particles that got there during repair work.
We press the new bearings into place (without lubricating).
Lubricate and install the shaft seals.
We assemble all the parts and elements of the automatic washing machine in the reverse order of disassembly with the implementation of all technological connections.
We launch the AFM in test mode.
If the previously present faults do not manifest themselves, the work can be considered successfully completed.
Work on the repair or complete replacement of the ACM drain pump is not so laborious in terms of disassembling the body of an automatic washing machine and boils down to the following steps:
Twisting and removing the back of the device.
Drain pump detection. It is located in the lower corner of the instrument case.
Release of the pump from the elements connected to it.
Removing the snail of a paddlewheel washing machine.
Checking the impeller and the casing for deformation changes, as a result of which, due to the adhesion of the impeller blades with the protective casing, the pump cannot function in normal operating mode.
After checking and detecting damage to the housing (casing), the blades of the impeller are trimmed with a knife by one millimeter (quite a sufficient size for the pump to resume normal operation).
Installation of elements and parts of the drain pump of an automatic washing machine in the reverse (from parsing) order.
If the reason for the failure of the drain pump was not its impeller, but pump wear, then it should be replaced with a new device, for the reason that repairing a worn-out pump is impractical and cannot ensure further uninterrupted operation of the LG washing machine.
At the end of any type of work (repair / replacement), a test wash is carried out.
Do-it-yourself LG washing machine repair on video.
To begin with, you should know that most cars of this brand are equipped with an emergency display system. If the machine is persistently trying to "tell" something to you with signals on the control panel, you should not ignore it (even if it continues to work). Take the instructions and see what the problem might be. You will not have to resort to more complex repairs later.
What are the most common problems with LG machines? Many faults are common to all washing machines. More often than other brands can fail - filler valves, drain pump, heating element. And the “Achilles heel” of LG's direct drive is the oil seals and bearings. Now - in more detail. First the problem, then the solutions.
There is no water in the mains.
The inlet hose is pinched or clogged.
The hose leakage valve (if equipped) has operated.
Filler mesh is clogged.
The water inlet valve does not work.
The pressure switch is not working properly.
Check for water in the plumbing system. If you turned it off, just wait for the resumption of its supply.
Inspect the condition of the hose.Eliminate pinching if necessary.
If the inlet hose has a safety valve, check its indicator. After the protection is triggered, the hose is changed to a new one (usually LG are equipped with conventional hoses, but options with a valve are sold separately).
The bay filter is removed with pliers. It is necessary to remove rust particles from it.
The filling valve can be checked by removing the top cover of the washing machine. When the valve is properly energized, it should open. Otherwise, it will need to be replaced.
The pressure switch is also located under the top cover and is attached to the housing. The tube suitable for it is checked for contamination. Further, the integrity of the wires and contact connections. The defective sensor must be replaced.
blockage in the sewage system;
the drain hose is clogged or kinked;
dirt on the drain filter;
the drain pump is faulty or blocked;
again, the notorious pressure switch.
What can be done to fix the problem.
- Disconnect the drain hose from the sewerage system and check if water will come out of it? I went - then the problem is in the blockage of the pipe.
- In principle, in modern LG machines, a thermal sensor (thermistor) is installed directly in the heating element. Therefore, we will check both the thermistor and the heating element at the same time. Remove the rear wall of the car (by unscrewing a few screws). We find at the bottom of the tank, a heating element inserted into it. We check the heating element circuit with a multimeter. For a thermistor, the test consists of measuring the resistance at room temperature and in a hot state - there should be a decent difference. Thermistors rarely fail. Therefore, it is most likely that the problem is in the heating element. It will be necessary to disconnect the wires from it and carefully pull it out of the tank. Then a new heater is installed and connected. We check the operation of the machine.
- To check the relay, you need to check the state of the contacts on the control unit of the washing machine. To remove the control panel, you need to remove the top cover. Next, pull out the powder receptacle. Two screws are visible under it, which must be unscrewed. The panel is held by latches. From above we find them under the bar and squeeze them out. Carefully (without undue effort) pull the bottom of the panel up.
All of the above malfunctions can be caused by a breakdown of the electronic control module. In this case, you will need to completely replace it. Changing the control unit yourself is not at all difficult. The main thing is to remember or photograph the location of the contact blocks.
What to do? At the first squeaks and a suspicion of wear on the oil seal, it is better not to delay the solution to the problem. And do not wait until the bearing collapses. One way or another, you will have to disassemble the LG washing machine almost completely. Removable top cover, back and front wall.LG has an engine on the back of the tank instead of a pulley. First, the rotor bolt is unscrewed and the casing is removed. Then the stator mounts are twisted. And he's also filmed. As a result, you need to disconnect all pipes and wires that can connect the tank to the body. At the end, the shock absorbers are removed. The tank is removed from the springs and pulled out through the open facade. The screws securing the tank are loosened. Further, the process of knocking out the drum and replacing the oil seal and bearings is standard for all machines.
Video (click to play).
As stated at the beginning, all parts for LG washing machines are readily available. And DIY repairs are totally realistic. And in comparison with the prices of services, the benefits for the home budget are very noticeable. Download dle 10.6 movies for free
