Lg wd 80192n DIY repair

Details: lg wd 80192n DIY repair from a real master for the site my.housecope.com.

Do-it-yourself training portal about repairing washing machines, repairing dishwashers, repairing boilers and refrigerators

The LG washing machine model WD 80192N was being repaired, the problem is that there is no water heating, and, accordingly, the machine began to wash clothes poorly. Based on experience, we make a preliminary conclusion that the heating element (heating element) is out of order, and it needs to be replaced.

Replacing the heating element LG WD 80192N involves partial disassembly of the machine, namely, you need to remove the back cover. First, turn off the machine from the network. We unfold the car and remove the back cover by unscrewing four screws.

On this, the disassembly of the LG washing machine actually ended. Removing the back cover, we see the ten.

It is necessary to check whether it is working properly, for this we remove the power terminals, take a multimeter and measure the resistance at the ends of the heater. The resistance of a working heater should be approximately 30 ohms.

The photo shows that the multimeter shows 1, which means infinite resistance of the ten, that is, it is faulty.

The heating element is a hollow tube, sealed on both sides, inside which there is a metal spiral in an insulator, and this spiral heats up when an electric current is applied. Over time, the spiral becomes thinner and breaks, and the machine stops heating the water.

The defect is quite standard, considering that the machine has been in operation for about 10 years. Next, let's look at how the LG heating element is replaced.

First, remove the engine drive belt so that it does not interfere.

Unscrew the first nut on the heating element and remove the mass.

Video (click to play).

We loosen the second nut, but do not unscrew it completely.

We remove the heater, for this we take a pair of flat screwdrivers, hook up the metal base of the heating element and pull it out of the tank.

The photo shows that ten not only "burned out", but literally exploded and fell apart. The inner spiral seems to be closed on the outer case of the heating element. One piece is missing, it remains in the tank, but you must definitely get it out, otherwise it can get into the drain pump and interfere with the pump's operation. Also, a piece can get between the new ten and the drum, and then there will be trouble. In order to extract a piece, I used a metal wire, folded one end of the wire into a hook and took out the missing piece.

With the same wire we get large fragments of scale out of the tank. Before installing a new heater, be sure to clean the shade seat from dirt and scale.

We take a new ten. The photo shows that a working ten shows a resistance of 31 ohms.

We install a new element, fix it well with a nut, assemble the machine and check it in the wash mode.

The type of repair described in this article cannot be classified as a complex repair, but the topic, however, requires certain skills. If you are not confident in your abilities, then it is better to seek help from professionals. Good luck with the renovation.

LG direct drive washing machines are in high demand among customers. The new design made it possible to significantly increase the engine resource, while the SM belongs to the affordable price segment.

But even such equipment is subject to breakdowns, and maintenance of LG washing machines in a service center is sometimes expensive. Therefore, we will tell you about the typical malfunctions of this brand and the possibilities of self-repair.

According to statistics, breakdowns of direct drive LJ washing machines occur after five years of operation. To understand where to start troubleshooting, let's look at how a direct-drive CM and a standard machine work.

Look at the diagram of the LG washing machine:

In the first case, the drum is rotated using a drive belt. In the second, the drum rotates the motor directly. Such a motor also does not have brushes that constantly wear out. In the event of a breakdown, you will immediately determine that the reason is in the motor, and not in the parts adjacent to it.

We have disassembled the principle of operation, now we will consider which nodes most often fail:

How can a user know where exactly the LG washing machine has broken down? For this, there is a self-diagnosis system. If a problem is detected, the system displays the EJ error codes on the display.

You just have to decipher the code and find the problem.

To repair a LG washing machine with your own hands, you need to know well the design features of the washing machine and its main faults that occur most often.

From time to time, many have a situation when the washing machine stops working normally. Modern units, including LG, have no problems with diagnostics and error detection. The fact is that the screen-display shows codes, each of which corresponds to a particular malfunction. LG washing machines have their own coding, deciphered in the attached technical documentation. It also provides practical advice on how to eliminate the resulting breakdowns.

Explanation of the main fault codes for LG washing machines:

Many problems that arise with LG washing machines can be solved independently, in accordance with the decoding of the codes displayed on the display. If the measures taken have not led to a positive result, it is recommended to perform a service test for a more complete diagnosis. Thanks to the information received, the repair of the washing machine can be done independently. Sometimes there are breakdowns that are not provided for by error codes. They also need to be able to identify and eliminate.

Sometimes the washing machine does not react in any way when the plug is plugged into the socket: the indicator lights do not light up, the musical greeting does not turn on. The reasons for this condition can be very different. Some can be easily removed on their own, while others - only in a service center.

Why the washing machine does not turn on:

Lack of electricity is the most common cause. For various reasons, an automatic machine or an RCD is triggered. Possible outlet malfunction.
Defective mains wire. The serviceability of the washing machine's power cord is checked using a multimeter. If a problem is found, the cord is completely replaced or repaired. All connections must be made only by soldering.
Malfunction of the power button, which receives power after connecting to the network. To check its performance, a tester is also used, set to the buzzer mode. The machine must be de-energized, and the button itself rings in both positions - on and off. If it is in working order, the multimeter will confirm this with a characteristic sound. If a malfunction is found, the button must be replaced.

Sometimes the LG washing machine will not turn on due to a malfunctioning noise filter (FPS). This device is designed to damp the electromagnetic waves emitted by the washing machine that interfere with the operation of other devices. When the FPS fails, it no longer passes electric current through the circuit, as a result, the washing machine does not turn on. Serviceability checks are carried out using a multimeter. It is necessary to ring the entrance and exit in turn. If there is voltage at the input, but there is no voltage at the output, then the FPS is faulty and needs to be replaced.

Sometimes the drum stops spinning in the LG washing machine. In this case, turn off the machine, drain the water, open the door and try to turn the drum manually. If the drum does not rotate, then it is jammed. This situation can arise for various reasons.For example, on LG top-loading washing machines, doors may open and catch on a heating element or other part.

Sometimes the drive belt jumps off, which has to be replaced along with the bearing. The bearings themselves fail due to wear of the oil seal, which allows air and water to pass through due to the loss of elasticity. A foreign object may enter between the tub and drum and prevent rotation.

When the drum is rotated by hand, but it does not rotate from the electric motor. The most likely reason is related to defects in the control modules. It is possible to solve the problem by resetting the program, but in more complex cases, the board needs to be repaired or completely replaced.

Another reason may be the failure of the drive belt, due to breaks or loosening. Sometimes the brushes of the electric motor fail, and the motor itself turns out to be faulty under the influence of water leaks or voltage drops. More precise reasons for the failure of drum rotation are established only after disassembling the washing machine and diagnostics.

After a certain time of operation, extraneous noises may appear in the LG washing machine, as well as uncharacteristic sounds in the form of a squeak, crackle and others. The main causes of extraneous sounds can be the following:

Quite often, situations arise when, while observing all the established norms, regarding the amount of laundry, washing powder and settings, water is still drawn into the tank too slowly or not at all.

In such situations, first of all, the presence of water in the system and its pressure, the position and serviceability of the valve for supplying water to the machine, as well as the condition of the water hose are checked. If everything is in order here, the washing machine must be freed from the laundry, disconnected from the power and diagnosed in order to identify malfunctions.

The main reasons for the slow water supply:

First of all, the correctness of the washing mode setting is checked. Some LG models have a no-drain mode option that may have been accidentally turned on. Next, the drain hose is inspected for kinks and blockages. If necessary, clean it, and at the same time check the siphon if water is drained through it.

The reason for not draining the water can be a filter that is dirty and clogged with various objects. Draining is significantly hampered or completely stopped. A clogged filter often leads to more serious damage to the unit, therefore it must be inspected and cleaned regularly. In addition, some small items of clothing can get stuck in the pipe, obstructing the escape of water.

A faulty pump, the sound of which becomes quieter in comparison with the usual mode, often becomes the cause of a violation of the drain. The machine makes a noise or hums, but the water does not drain. The malfunction occurs due to physical wear and tear of the pump, designed for 3-5 years of operation. Small objects leaking from the filter can jam the impeller.

Sometimes all systems work fine, but the water is still not drained. The main cause is a blockage in the drain hose, which must be removed and cleaned. The second reason is associated with a pump that has exhausted its resource and is able to rotate only without water, dry. When water is supplied, it jams, power is lost, and it stops rotating.

To avoid such situations, experts recommend taking a number of preventive measures:

Remove all foreign objects from pockets before washing.
The weight of the laundry loaded into the drum must strictly comply with the instructions, overloading is strictly not allowed.
Use only high-quality detergents in the right amount for washing.
We recommend using a stabilizer during washing. This will help keep your equipment safe from power surges and surges.

Water leakage in LG washing machines is one of the most serious malfunctions when you need to take the most urgent measures.Leaking water can not only flood the neighbors on the lower floor, but also damage the electronic parts of the unit. Therefore, if a leak is detected, the wash should be stopped immediately and the water drained. The water supply to the machine is completely shut off.

The main reasons for water leakage in LG washing machines are:

A leak near the filter indicates poor tightening after cleaning, damage to the O-ring or thread.
Water appears mainly in the front of the machine and often spills out through the doors. This becomes especially noticeable during the spinning process. The cause of the malfunction may be a loose door or a damaged hatch seal.
If a leak occurs while draining the water, the leaking drain hoses must be replaced.
Leakage can occur due to a rupture of the inner pipe, depressurization of the connections, or a defect in the water pump. In these cases, water comes out centrally under the washing machine or closer to the front of the washing machine. If a leak is found near the rear wall, it is likely that the bearing or the sealing gland will fail.
When the flow starts with the water supply, the problem may be in the powder tray, which is clogged with detergent residues. It is possible that the inlet hoses and water inlets are also clogged.

The most difficult part of the LG washing machine is undoubtedly the control module. In case of failure, the control panel stops the execution of all functions of the washing machine. After all, this unit turns on and off the device, organizes the direct washing process, selects the mode, provides rinsing and spinning, at its command, the water is heated and cooled.

Before you independently repair the control module, you must diagnose it. In case of obvious malfunctions, the machine does not spin the laundry normally, and the error code is not displayed on the display. The lamps located on the control panel at the same time or do not light up at all. Water is not drawn into the tank even if the required mode is set. The wash itself stretches for 3-4 hours in a row without stopping and switching to other modes. There are constant freezes of the device, there are difficulties with setting the necessary programs.

These and other signs gradually cause the complete inoperability of the washing machine. If at least one of them is available, the question of urgent repair of the control module should already be raised. Self-repair is recommended only to those people who have knowledge and experience with electronic circuits. In case of incorrect actions, the module will completely fail, and with it some components of the washing machine.

If, nevertheless, a decision is made to repair yourself, you must follow a certain procedure:

The module is cleaned of sealant.
It is then carefully removed from the compartment away from the transformer.
After removal from the electronic module, the remainder of the sealant is removed.
Further, repair work is carried out.
After repair, a protective varnish is applied to the board sections.

In some cases, the module is not completely removed, only the necessary area is cleaned from the sealant, which is then repaired.

Employees of all kinds of workshops and service centers persistently accustom us to the thought: attempts to repair a modern washing machine on our own can only lead to the final damage of the unit.

But workshop services sometimes cost several times more than the actual cost of new parts.

And there are also very simple cases when the machine simply needs to be cleaned, for example. Such work will be quite within the power of the owner. Let's take a look at how to repair an LG washing machine with your own hands, and how to diagnose faults, for example.

In fact, a washing machine is a tub in which a rotating drum is installed. The latter forces the laundry to actively move in water saturated with detergent. The machine is filled with water due to the pressure in the water supply to which it is connected. For the best effect, the water is heated (the temperature depends on the type of fabric).

Dirty water is pumped into the sewer, if the machine is connected to it, or into the bathtub.

Knowing how the machine works will help you better understand the causes of faults. Apart from the tank and the drum, this is what is included in its composition:

Control module. The "brain" of the system, coordinating the work of all electronic devices.
Bearing unit with an oil seal, in which the drum shaft is installed.
Mesh filters: one at the inlet to the machine, the other in front of the pump.

Electronic and electrical devices include:

electric motor (rotates the drum);
TEN (heats the water);
filling valve (this is an electric tap that the machine opens to fill the tank with water);
pump (pumps out waste water);
temperature sensor;
a level sensor, also called a pressure switch or pressure switch (with which the machine controls the water level).

From below, the tank is mounted on shock absorbers, and from above it is suspended on springs. The motor can drive the drum shaft into rotation either directly or by means of a belt drive.

A little home appliance repair skills can always come in handy, especially if you own a washing machine. Do-it-yourself Ariston washing machine repair - common difficulties and their elimination.

We will analyze the main problems of Samsung washing machines and how to fix them here.

As you can see, the washing machine consists of a fairly large number of different components, and the breakdown of any of them will inevitably affect the operation of the device as a whole. Here's what can happen:

It is easy to see that a typewriter has to combine two things that a sane person usually tends to keep away from each other: water and electricity. As long as the water is where it should be, there is nothing to fear. But if she finds at least an insignificant possibility of leakage, the risk of unauthorized closure of contacts immediately arises.

As you know, the work at the washing machine is rather dirty.

Collecting in some places in the form of muddy deposits, the dirt can completely block the path of water.

In addition to dirt, all sorts of small debris often gets into the machine, which we carefully store in our pockets, which makes the likelihood of a blockage increase dramatically.

Chemists have come up with many different materials, but none of them are completely eternal. Therefore, the moving parts - the bearings, the belt, and sometimes the pump impeller - have a limited resource and must be replaced from time to time.

The same can be said for the seals. Their wear and tear leads to the fact that water instead of sewage begins to pour onto the floor.

Electronic devices, like humans, can sometimes go crazy. Especially if the voltage in the mains from time to time makes dizzying surges, as it happens with us. Of course, it is impossible to repair an electronic unit without special skills and equipment, but even an amateur can easily replace a burnt-out thermal sensor or heating element.

For an amateur repair of a LG washing machine, you will need a very modest arsenal:

Phillips and flathead screwdrivers;
wrenches 10 and 17;
multimeter;
phase indicator.

In some cases, glue or sealant may be required.

What exactly needs to be repaired can be suggested by the machine itself. In the event of a malfunction, a special code is displayed on its display, by which you can approximately determine the cause of the problem.

When disassembling a typewriter, do not rely on your memory. Before disconnecting, mark the contacts and their corresponding connectors, and even better take pictures.
This applies not only to the electrician, but also to all kinds of fasteners and assemblies that you intend to dismantle.

Let's consider several typical situations that the owner of a "washing machine" may face.

First of all, we note that such sounds do not always indicate a breakdown.

They can also occur if too little laundry has been put into the machine and it has collected on one side of the drum, which causes an imbalance (the display may show the UE code).

It is also necessary to make sure that the LG machine is installed without distortions (checked by the building level).

If the laundry has been loaded correctly and the machine is level, the cause of the unusual noises should be looked for in the bearings. Apparently, one of them has fallen into disrepair and needs to be replaced. This operation will take a lot of time, since you will have to disassemble the entire machine, but it does not have any difficulties that require special knowledge.

A few tips will help to disassemble the unit:

To remove the top cover and rear panel, it is enough to unscrew the screws, and to dismantle the front panel, you first need to unscrew the hatch and disconnect the sealing collar. The latter is held in place by a clamp tightened with a small screw. To get to the screw, you need to carefully pry the clamp with a flat screwdriver and move it in any direction until the fasteners are found.
The top corner must also be removed, as it will interfere with the removal of the drum.
Before dismantling the drum, disconnect the upper counterweight from it - then it will be easier to pull out the element.
It is better to remove the drum together, holding its upper springs.

The bearings sit very tightly on the shaft and in the sleeve, so an impressive effort is required to dismantle them. Some craftsmen knock them out with a hammer, substituting a wooden block under it, but this approach cannot be called anything other than barbaric - you can damage the shaft and other elements. The bearings should be removed and installed using a puller.

Washing machine drum

This is a simple device and it is not difficult to construct it yourself. It can consist, for example, of a plate with holes and 2 studs with L-shaped hooks welded to them.

The plate rests against the end of the shaft and pins are threaded into its holes so that they engage the bearing. By tightening the nuts on the studs little by little, we will create the force necessary to remove the bearing.

If water seeps into the sump located under the machine, it will react by showing the code "E1" on the display. There may be several reasons:

The gasket between the two halves of the tank ceased to hold water. This usually happens if the tank was disassembled shortly before. It is necessary to install a new gasket, and before that it should be lubricated with silicone sealant.
The oil seal, which is installed next to the bearings, is worn out. In LG machines, this oil seal is sometimes destroyed by the drum, which touches it as it rotates. The oil seal needs to be replaced.
The hose that connects the tank outlet to the pump may burst. It is "treated" by replacement.

Due to design flaws in LG machines, the new oil seal is not always able to be put in place. In this case, it is planted on a sealant (the most reliable is the composition of the Dyson brand).

Water can also flow out through the hatch seal, which in this case is also changed (how to remove the seal was described above).

The signal on the scoreboard is "OE". First of all, you need to empty the tank through the emergency drain. To get to it, open the hatch at the bottom.

Now you can look for the reason:

Unscrew the drain filter and clean it and the area around it from dirt.
Put the unit in the “drain” mode and look through the hole from under the filter at the pump impeller - has it started to rotate? If not, you need to disassemble the pump and check if the impeller is jammed with a foreign object. Also, it can wedge due to the formation of a strong backlash. Depending on the identified defects, the pump is repaired or changed.

If the pump is working properly, you should start cleaning the drain hose connected to it.

Clean the detergent dispenser container from powder adhered to it.
It is sometimes useful to unscrew the heating element (its shank sticks out of the tank at the bottom of it) and descale it. In this case, the gasket must be changed to a new one every time.
Clean the filler and return filters from time to time.

It is also recommended to renew the grease on the oil seal from time to time, unless, of course, you are afraid of the need to completely disassemble the machine for this.

Was the washing machine broken at the worst possible moment? It is quite possible to fix some problems yourself. Do-it-yourself Beko washing machine repair - types of breakdowns and their elimination.

You will find everything about self-repair of Polish washing machines Hansa on this page.

The Korean company LG makes great direct drive washing machines. This technology really significantly increases the service life of the engine and moving elements. However, these machines are also characterized by specific malfunctions, noted by the specialists of the service centers as the most common. If you are the owner of an LG washing machine, then in 80% of cases you will have to deal with the malfunctions discussed in this article.

Experts from the world's leading service centers note the relatively high reliability of LG washing machines. The most "tenacious" unit of this machine is considered to be the engine, which breaks down only in one case out of 500 calls to service centers, and then in half of the cases, the cause of the module malfunction is a factory defect. Moving elements are also considered to be quite reliable, except for bearings, they are repaired more often.

What units of the LG washing machine break down most often? Let's list them:

a heating element;
pressure switch;
bearings;
wires and terminals;
drain pump;
filling valve.

Malfunctions of these most important units of the washing machine manifest themselves in different ways. It is necessary to carefully analyze the "symptoms" in order to more or less accurately diagnose the problem of the module even before disassembling the "home assistant". In particular.

Note! When diagnosing faults in the washing machine with your own hands, be sure to listen and take a closer look at its work at the stages of washing, rinsing, spinning and draining. In addition, read the user manual, any deviations from the norm should alert you.

To get to the heating element of the washing machine, you need to unscrew several fasteners that hold the back wall of the LG washing machine by yourself, and then dismantle this wall. Next, you need to pay attention to the lower part of the tank (near the very bottom). Two paired contacts with a screw in the middle should stick out from there, to which several wires go - this is the ten. We check the contacts with a multimeter, if its display shows a value less than 20 Ohm - the ten is faulty.

Removing the ten is easy. We unscrew the screw we mentioned with our own hands, pry on the sealing gum with a screwdriver and pull out the heating element from the bowels of the tank. We visually check the status of the module. Burnt teng rarely does not have any visually noticeable damage (usually these are burnt spots). In most cases, the heating element breaks down due to a layer of scale that settles on it. Also, a breakdown can be provoked by a voltage drop or water that gets on the contacts. The video guide will help you to correctly remove the ten.

Repair of this module of the LG washing machine is not possible, only replacement. It is necessary to purchase an original spare part from the manufacturer and install it in the tank of the washing machine, not forgetting to install the sealing rubber. In the process of installing the heating element, you need to be most careful about the sealing rubber of the heating element. To make it sit better in place, you need to lubricate it with a small amount of machine oil.

Important! If the sealing rubber of the heating element sits loosely in the bore hole, water from the tank will seep onto the contacts of the heating element and it will most likely burn out again in the near future. Be careful.

Washing machine electrical repair LG boils down to checking all the wires and terminals coming from the control module to all of its units. It's not just about checking all the wiring with a multimeter - it goes without saying. It is also necessary to carry out a visual check: torn clamps, fragments of wires without insulation, traces of burning and melting of contacts. All wiring problems that can be detected during the check must be resolved by replacing damaged conductors and terminals - this is the repair of the electrician.It is not difficult to diagnose faults in the filler valve of an LG washing machine on your own, and it will not be difficult to repair this module with your own hands if you act methodically, according to a pre-planned plan. Dismantling and replacing the filler valve with your own hands is carried out in the following order.

Unroll the washing machine.

The inlet hose, which is connected to the water supply at one end, is screwed to the inlet valve with the other end. We turn off the cold water supply by turning off the tap.

We unscrew the inlet hose.

We take out, check and clean the filter of the inlet valve, it may be clogged with dirt and the water does not pass.

If everything is in order with the filter, remove the top cover of the washing machine, unscrew the two screws holding the valve, disconnect it from the pipes.

Next, we need to check the rubber bands of the valve, in 90% of cases the problem is their wear and the inability to retain water in the future. If so, change the rubber bands.

If it's not about the rubber bands, then most likely the problem is in the control electrics of the valve. In this case, the entire valve must be replaced.

To the drain pump of the washing machine LG can be reached without even disassembling it. You just need to tilt the machine on its side, after that it will be possible to get close to the unit through the bottom. We check the drain pump sensor with a multimeter, if everything is in order, then the problem is in the unit itself. Next, we proceed in order.

Unscrew the lower part of the front panel of the machine.
We unscrew the fasteners securing the drain pump.
We substitute the basin, since water will flow from the unit during removal.
Disconnect the plugs and remove the wires with the sensor.
Disconnect the pipes, drain the water and remove the unit to the side.

Note! Before placing the clipper on its side, remove the powder cuvette as directed by the user manual, as water remaining in the cuvette may spill onto the control box and damage the electronics.

Once the drain pump has been removed, it is best to have it checked and repaired by a specialist. Only he can finally say whether the pump has really come to an end, if so, then you need to buy and install a new one. Assembly is carried out upside-down. The easiest way is to change the pressure switch (water level sensor) of the washing machine. If you manage to disassemble it correctly, then it will not be difficult to replace it yourself.

Bearing failures are a matter of time or a factory defect. The user can influence this process only by the intensity of the use of the home assistant. Bearing malfunctions must be repaired immediately, because if this is not done, the loose pulley can damage the tank and then repairs will be very expensive. In this case, the user manual will not help; you either need to contact a specialist or study specialized information.

Thanks to direct drive technology, which is implemented on most models of washing machines from the company LG, bearings, motor, pulley and other parts wear out much more slowly and last longer. Nevertheless, there are still cases of bearing failure, and this poses a problem for “self-repair lovers”. Not everyone knows how to properly remove the bearing from the drum, however, to start doing this, you need to remove and disassemble the washing machine tank.

Bearing repairs must be done very carefully, using a special hammer with a bronze bump and a thin metal rod. It is necessary to pull out the bearing by striking its opposite edges.First, we place the rod on one edge of the bearing and strike it lightly with a hammer, then transfer the rod to the other edge and again strike it lightly. The procedure must be repeated until the old bearing pops out, then a new bearing can be put in its place.

In conclusion, we note that malfunctions of any module of the LG washing machine, you can try to fix it. Of course, even if you study the relevant technical information and expert advice, successful repairs are not guaranteed, but it is definitely worth trying, especially since in most cases you have to deal with typical breakdowns. If something doesn't work, you can read the washing machine repair manual.

Everything in life breaks down at some point, because something eternal has not yet been invented. This article will focus on repairing a washing machine. Depending on the manufacturer, operating conditions and many other factors, this moment will come sooner or later.Washing machine device.Our family has a LG washing machine, they bought it on the recommendations of several specialists. But the impeccable period of LG's work was not too long, the wife's “favorite” worked for a little more than 4 years.The machine stopped before it finished washing.During the next wash, something shot inside and everything stopped. Attempts to restart the unit were unsuccessful. Disconnecting from all communications (power supply, water, sewage) and removing the back cover, it was clearly visible: water through the control hole of the oil seal, flowing down, fell on the electric motor connection connector - and something shorted. I had no experience in repairing modern washing machines, and such a “good” moment finally presented itself.First of all, the electric motor rang (there is a 10-pin connector), everything showed that the “engine is alive”. But to see this part of the car, it had to be completely disassembled. As I later saw, the engine is mounted between the covers of the outer drum.The washing machine stopped in this mode.Removing the washing machine module.For further disassembly, it is necessary to drain the water by opening the hatch at the bottom. On the right, there is a short, thin hose with a plug.After checking the engine, it was necessary to examine the electrical part further. To do this, I removed the top cover, it is fastened with two bolts at the back. All the wires were outwardly in good condition, which means that it was necessary to remove the module (brains). It is fastened with latches on the right side, and with two self-tapping screws on the left, which are under the container for washing powder. In the photo, the module is removed.Externally, the module was in perfect condition. Began to deal with it in stages. The entire printed circuit board is sealed with a soft compound on both sides.Front panel for washing machine.This way of finding the fault gave nothing. It was necessary to open the compound. I tried to do it from the open, visible side, but I realized that it would be very difficult to lift the board, and most likely impossible. I read on the Internet on the forums how to do it. It turns out that you need to do the autopsy from the side of the display, cut out the windows in the plastic with a knife or just a soldering iron, and I started:I remove the display board - it is latched at the edges - and cut out the windows for verification, in the place where the circuit is examined.Opening the washing machine module for repair.I had to make several windows. Section after section stubbornly led to the processor. The reason for the failure of the module was in it. Further renovations just didn't make sense. It's easier to just buy and replace a module.Again I “went” to the Internet for prices for modules. They turned out to be quite acceptable (in the region of 3 thousand). This is 60-70% cheaper than repairs in the service. I called the local craftsmen, in one place they offered a used one. (unrepaired) for 2.200 rubles, and bought it. I put it on and started a short wash (30 min.). The machine ran like clockwork again. Well, I sat next to me and didn’t allow the water to hit the connector again.The oil seal had to be changed unambiguously, and at the same time, and look at the bearings (whether water got into them).The washing was carried out when checking the module with the cover removed, which means that it is no longer necessary to remove it. I remove the module again, disconnecting all the connectors and wires. I remove the pulley by unscrewing the bolt in the center (the thread is ordinary - right). Taking off the belt, just in case, I looked in which direction the letters were written in order to put it in the same way.Removing the washing machine pulley.The pulley can be removed without any effort.Removing the loading door of the washing machine.Remove the loading hatch from the front side. It is secured with two screws.Remove the rubber bellows clamp.After that, you need to remove the clamp that holds the large rubber sealing corrugation.We remove the electrovalves for supplying water to the washing machine.We remove the water supply solenoid valves. They are attached with two screws to the rear wall.Removing the detergent container.Remove the powder container and suitable rubber tubes.Removing the upper front corner, for ease of repair.It is imperative to remove the upper bar (corner), since you cannot pull out the drum with it. Next, you need to disconnect the lower drum mount, there are two of them.Bottom fastening of the washing machine drum.By pressing on the protruding antennae, they can be easily pulled out of the landing site. The picture clearly shows these antennae. Almost everything that connects the drum to the body seems to be detached.Upper springs holding the drum of the washing machine.Now the drum hangs only on springs. And it is advisable to do the next stage together.Side weights of the drum of the washing machine.Grasping the springs, we remove the drum from the machine body. The next step is the removal of loads, both top and side. It is better to remove the upper one before removing the drum (the weight will decrease).Washing machine body with electrical wiring.Only one building remained from the “washing machine”. The weights were removed from the drum, then we remove the retaining ring that holds the sealing corrugation (unfortunately, I did not take a picture).Washer rubber seal and retaining ring.There is a photo, but later, in which the corrugation and the retaining ring are clearly visible.Drum of the washing machine without weights.And already without loads I took the drum out into the yard, the weather allowed. Next, the upper drum must be disassembled. It consists of two halves, which are connected in a circle with self-tapping screws. These halves are connected hermetically, since there is water in this drum during washing.Inside the plastic drum is another drum, or stainless steel tub for laundry. Now you can see why the oil seal leaked and in what condition it is.Washing machine drum cover with bearings and oil seal.The photo clearly shows that during washing, the iron drum rubbed (clung) to the oil seal and damaged it. I must say right away that during the wash, the washing machine made a quiet creak. We did not pay attention to this sound, especially since it appeared at the very end of the wash.The drum lid is cracked.Now everything was clear, it was rubbing on the oil seal. The gland itself was removed from the seat without any effort. Having put this detail in order, I saw that on this cover around the gland there were cracks, so far barely noticeable, which means that there is a high probability that the process will go on and then the drum itself will flow. In the photo, I indicated these cracks with arrows. The bearings were in excellent condition and no water got into them. He began to put a new oil seal, but he "did not want" to sit in his nest. Painfully, this question was not finalized by the designer. And I decided to glue it.Refinement of the inner side of the drum and replacement of the oil seal.For this purpose, I bought a Dyson sealant, which has no equal from silicones (from experience). He put the gland on the glue, and at the same time filled the nearest sinuses with glue. I did the same procedure on the other side.Reinforcement of the outer side of the washing machine drum.I think it will add some rigidity to this part. I also improved the drainage. I inserted a tube of a suitable diameter into the hole and fixed it on the drum lid with the same glue.Installation of drainage from the control hole of the stuffing box.See how it turned out.Then he assembled the washing machine in reverse order.