Kandy machine does not drain water does not wring out DIY repairs

Moscow and Moscow region
Repair of washing machines
Refrigerator repair
repair of air conditioners
dishwasher repair
repair of drying machines

In 1945, in Italy, the small town of Monza north of Milan, the Fumagalli family Candy, which already in 1946 was the first in Europe to produce a household automatic electric washing machine.
Modern washing machines Candy (Kandy) has an oval shape of the tank, which reduces the volume of water that is not in direct contact with the laundry, thus saving energy when washing with boiling.

Everything is fine and wonderful until the washing machine gets from the store to our apartment.
Neither the shape of the tank, nor other charms declared by the manufacturer, will save you from such frequent breakdowns as the lack of draining water from the washing machine. Candy, water heating, knocking out plugs (automatic machine, RCD) and other breakdowns, which our operators have heard a lot about from 9-00 to 22-00, daily advising the owner of washing machines Candy on the repair of a washing machine.

On this page, we will give advice and describe the possibilities of minor repairs to the washing machine within the instructions, guided by the main commandment of the repairman of washing machines Candy - "do no harm".

Washer Candy not draining water? did not wring out the laundry and stopped ,
the model is not so important here - all washing machines work according to the same laws of physics.

The washing machine has a special filter that retains forgotten items from the laundry. open the filter cover.
Some models of washing machines have a corrugated hose - remove it, open the plug and drain the water into a container.
Place a cloth on the floor before removing the filter, as there may be residual water in the pump (pump).

Turn the filter counterclockwise until it stops in an upright position. Do not make great efforts to unwind the filter - often the filter seal is “welded” to the socket and then you can tear off the filter handle, which is fraught with replacing the entire filter.
Please note that in some models of washing machines Candy the manufacturer has provided an additional blocking of the filter with a screw, so you will have to stock up on a screwdriver.

If this fails, remove the filter from the seat. you will have to trust the repairman of washing machines, since the filter in such conditions must be removed from the inside of the machine, having previously disassembled it. This often happens when the owner of the washing machine does not clean the filter for more than 3 years and uses the boiling mode.

After cleaning the filter, put it back in its original place, following the reverse order. Be careful, the filter must be screwed on without distortions and rather tightly, otherwise water will spill onto the floor during washing.

Now check the draining of the washing machine. Washing machine repair possible Candy this is where it ends. If this did not happen, we will continue the diagnosis.
Check the cleanliness of the drain hose and drain, this is especially important when the washing machine is connected to a siphon from the sink. Check the cleanliness of the siphon.
Remove the blockage.

If, as a result of all your activities, the washing machine Candy does not want to drain the water, you will have to invite a repairman for washing machines. What will the master check and repair?
1. Drain pump (pump).
2.Pressostat (water level sensor)
3. Electronic module.
4. Drain pipes are inaccessible to the user.
5. Open circuit in the washing machine Candy.

Thus, all breakdowns associated with draining water from the washing machine, the lack of spinning the laundry and even turning on the washing machine can often be corrected by cleaning the filter, which our operators, first of all, recommend to customers.

Washing machine Candy (Kandy) washing machine does not heat the water or it heats up very slowly .

In this case, a qualified person can find out the reasons and eliminate them. repairman for washing machines Candy (Kandy)
1. Malfunction in the heating system of the washing machine.
2. The thermostop has not been reached.
3. Possibly low voltage in the network
4. The heating element is broken or the washing machine does not heat the water due to lime deposits on the heating element. If YOU in 3-5 years of operation of the washing machine have never cleaned the heating element - heating element, then do not do it. Scale after processing the washing machine will clog the entire drain system and even damage the pump!
5. The heating element relay is faulty, and the washing will be completed without heating the water.
6. Defective temperature sensor.
7. Break in the connecting network.

If you did not find the answer in this article about repair of washing machines Candy (Kandy), our
the operators of the service center for the repair of washing machines will answer all your questions about the repair of washing machines, make an approximate estimate of the repair, call tel.

Our service center masters repair of washing machines Candy (Kandy) at home work seven days a week from 10-00 to 22-00 (by agreement with the client, the opening hours are shifted) and serve all models of washing machines Candy:

• Candy AC 108
• Candy Activa 108 AC
• Candy Alise CSW 105
• Candy Aquamatic 10 T MET
• Candy AS 108
• Candy C 2085
• Candy C2 095
• Candy CB 1053 TR
• Candy CE 637 XT
• Candy CG 1054 T
• Candy CIW 100
• Candy CIW 100 T
• Candy CM 106 TXT
• Candy CNL 085
• Candy CO 0855F-07S
• Candy COS 588F-07S
• Candy CR 61
• Candy CS 288
• Candy CS2 094

• Candy CSN 62 T
• Candy CSW 105
• Candy CT 1096 TXT
• Candy CTAS 100
• Candy CTD 8766
• Candy CTE 101
• Candy CTF 806
• Candy CTG 105 SY
• Candy CTH 1476 SY
• Candy CTI 1023 V
• Candy CTS 80 T
• Candy CTY 8546 SY
• Candy CWB 100 S
• Candy Energa 735
• Candy GO 086
• Candy GO4 126 TXT
• Candy GOY 1050 D
• Candy Holiday 084F
• Candy ICL 100 TR H / C
• Candy Slimmy 855 XT

The team of the service center for the repair of washing machines

If the washing machine does not spin the laundry (spinning does not work), then this malfunction has several reasons, including those associated with the operation of the drain pump.

• the laundry is not wrung out after washing, water is dripping from it;
• the drum rotates, but there is no spin;
• washing stops at the drain, water does not leave the tank;
• there is no water in the tank, but no spinning occurs;
• during washing, the water is drained, and at the end, after rinsing, it is not drained.

Why doesn't the washing machine spin?

1. Drain pump filter clogged.
2. Clogged branch pipe leading from the tank to the pump;
3. If a large foreign object enters the pump impeller and becomes seized, the pump cannot rotate.
4. The drain hose is blocked.
5. Siphon or sewer blockage.
6. Drain pump defective.
7. Worn brushes of the electric motor.
8. Defective motor.
9. Malfunction of the heating element of the heating element.
10. Electronic module defective.

Eliminate the malfunction of the drain. Make sure the machine is draining off the water. If the water has not drained, then the spinning will not occur.

Defective heating element. If the water is drained, then provide access to the heating element by disconnecting one or another side wall of the washing machine body. Check the heating element for an open circuit with a tester. In case of malfunction, replace the heating element.

Checking the electric motor. Checking the motor. Before removing the engine, remove the drive belt, remember how everything is installed, disconnect the terminal with the power supply wires and the ground wire, unscrew the fastening screws and carefully remove the engine from the runners.

First, on brushed motors, which are the majority, you need to check the brushes. They are usually attached to the outside of the housing and pressed tightly against the manifold. Over the years of operation, the graphite brushes are slowly erased and, upon reaching a certain minimum length, they no longer fit snugly to the engine manifold, which leads to a loss of its power and the machine stops squeezing out the laundry.

Graphite coals of worked brushes are no more than 5-6 mm long. In this case, the repair is reduced to replacing the brushes. If the brushes are more than 5-6 mm, then you need to check the motor itself, perhaps there is a leak on the case. After eliminating the malfunction, we install the motor in place.

Verification of works. Before the complete assembly of the walls of the case, we connect the washing machine to the mains and check the spin mode. If the malfunction is eliminated, we disconnect the machine from the network, finally collect everything and check it again. If the malfunction cannot be eliminated, you can ask us a question by e-mail, we will try to answer it.

Another possible reason. Also, the cause of this malfunction may be a failed electronic module.

The module is not cheap, so you need to be sure before replacing it. It is best to have this done by a specialist from the service center.

Automatic washing machines Kandy are affordable and compact. Convenient control system and a wide range of programs have made the technique popular among users.

However, over time, even reliable equipment can fail. Is it possible to repair the Kandy washing machine with your own hands? Quite!

You just need to find out what the error codes on the control panel mean, and then find and fix the malfunction.

Let's analyze the main problems that are typical for machines of this brand. We will also find out how you can repair Candy washing machines with your own hands.

Have you noticed that the Kandy washing machine does not drain water. The program can stop right in the middle of a wash. Due to the fact that the water does not leave completely, you take out wet things after spinning.

What are the reasons for such a breakdown:

• The drain system is clogged. If debris gets into the drain filter or hose, it will block. It is necessary to check the pump and the branch pipe from the tank to the pump.
  
• Breakdown of the drain pump (pump). Often, small objects entering the pump cause damage to the pump.

Why isn't the Candy washing machine working? You start the washing machine as usual, but it does not respond to your actions. Let's figure out the reasons for this problem:

• Defective mains cable or extension cord. He could burn out, twist.
• Lack of voltage in the network, or it is not enough to start SM Kandy. This can happen if repair work is being carried out on your site, a powerful tool is involved, and so on.
• The contacts on the start button are oxidized, so the machine does not respond to switching on.
• Malfunction of the control module of the Kandy washing machine. The module is responsible for all programs in the CMA, therefore, if it breaks down, the technician refuses to work.

If you notice a puddle of water under the washing machine, you need to urgently look for a leak.

Attention! Do not step into the water, you may be electrocuted. If possible, disconnect the CM from the network or turn off the electricity supply on the switchboard.

• Dispensing tray. If the tray is not periodically cleaned, powder accumulates in it, which clogs the pipe. As a result, leakage comes out of the tray.
  
• Drain connection of the Candy washing machine. If it is damaged, water flows out through the bottom of the CM.
  
• Rubber cuff of the hatch. With prolonged use, the cuff could leak and lose its tightness. Or it is damaged by small items during washing.
  

The washer does not start the washing process or washes things in cold water. The reason for this is a malfunction of the heating element (heating element). Basically, the element fails due to scale or damaged contacts.

Wear of bearings, oil seals, motor electric brushes leads to various malfunctions in the Kandy washing machine. For example, you may notice knocking and rumbling when the washer is running, or the drum stops rotating.

These include problems with closing the hatch door, faulty wiring between parts and the control module, and a faulty Candy washing machine control board.

How to figure out what kind of breakdown happened in your car? The error codes will help you.

Thanks to the self-diagnosis system, a malfunction code is displayed on the Kandy washing machine display. After decrypting it, the user understands which detail needs to be checked. This makes it possible to independently repair Candy washing machines.

Depending on the type of model, CM can show an error in different ways:

• Electronically controlled Activa models show an error on the display.
• Models Candy Aquamatic (Kandy Akvamatik), signal about a malfunction by blinking the bottom light on the left. The number of flashes after a pause means the error code.

For washing machines Candy Holiday, Aquamatic, Activa and other models, the following error codes are characteristic: E01, E02, E03, E04, E05, E09.

A washing machine that has been used for several years can break down at any time. The symptoms of such a breakdown are very different, for example, the Candy washing machine does not spin the laundry after washing. What to do in this case? Firstly, do not panic, and secondly, check what could cause such a malfunction. This article will help you with this.

Faced with the problem of the lack of spin in the machine, you must first eliminate all user errors. That is to say, make sure that the machine has really broken down. The fact is that the laundry will remain wet if a mode was selected for which spinning is not provided or it runs at low speeds. As a result, it seems to you that the machine has stopped spinning well.

In addition, some users turn off the spin, and then forget to turn it on. Another common reason when the washing machine does not spin is improper distribution of the laundry. This happens when there is too little laundry in the drum, or it is bulky, but very light, for example, organza curtains.

In this case, you need to check whether the machine is spinning in principle by turning on the spin function separately and putting cotton items, for example, towels, in the drum.

Poor spin or lack of spin can be caused by a clogged drain filter. It is enough to unscrew such a filter located at the bottom of the machine and rinse it. When unscrewing the part, be prepared for water pouring out of the hole, and therefore prepare a good large rag and substitute a flat container.

If the washing machine does not spin, under no circumstances, even a separate spin function does not start, then it is more likely that some part has broken in the machine. Most often, Kandy washing machines fail:

• drain pump;
• control module (more precisely, the controller on the module);
• tachometer.

Breakage of any of these parts blocks the operation of the equipment; spinning is not carried out. To establish a breakdown and fix it, you will have to stock up on time and tools. First of all, you will need screwdrivers and pliers, as well as a multimeter.

Troubleshooting is best done with the pump. It is removed in Kandy cars and installed through the bottom. To do this, you need to put the equipment on its side. Further, all wires and pipes, which are held by clamps, are disconnected from the pump.

For your information! Having disconnected the pipes from the pump, they can be washed at the same time using a non-rigid brush. Thus, you will not only clean them of dirt and mucus, but also from an unpleasant odor.

With the pump removed, first remove the cover and check the performance of the impeller. If there is no hair and debris on it, it rotates well, then proceed to check the electrical part of the pump.Taking a multimeter, check the resistance of the part. If it burns out, then there is only one option - to buy a new pump and install it instead of the old one.

After the pump, check the tachometer. It is installed on the motor, so this test procedure is quite justified. To do this, you only need to open the service hatch of the housing at the back or remove the entire rear cover. Below, under the tank, you will see the engine, on the shaft of which the tachometer is located. Before removing it, you must first remove the drive belt from the pulley and the engine, and then unscrew the engine and remove it from the machine.

Now we disconnect the wires from the sensor and measure the resistance, which should normally be 60 ohms. Note the bolt that holds the sensor. It should not dangle, otherwise the RPM sensor will "glitch". The replacement of this part is written in the article Tachometer in a washing machine.

Important! The motor sensor breaks when the washing machine is overloaded with laundry. Therefore, never load your “home helper” to the maximum, as the laundry will stretch worse and the wear of the parts will increase.

Perhaps the most problematic part of the Kandy washing machine is the control module. This is the electronic part of the washing machine, which is not so easy to check, especially if you have not encountered this and are a complete layman. If this is the case, then it is better to immediately call the master and entrust this work to him, since otherwise you can run into trouble that will result in significant costs.

If you are at least a little versed in electronics and you had to work with printed circuit boards, carefully check all the controllers that you see in turn for operability using a multimeter. One of them is responsible for spinning. You can, of course, pre-download the module diagram and find out which part is responsible for what, but it is much easier to check and detect a malfunction by typing. True, this will work only if the controller is really faulty, if there is a problem with the track or other semiconductor part, the circuit will be needed unambiguously.

Summing up, we note that if the washing machine worked, worked, and then "bam" - decided to stop wringing, you need to immediately look for the cause of the problem. It is important to remember that a malfunction found at the wrong time will lead to a train of additional problems. And the longer we operate a faulty washing machine, the more expensive the repair will then be.

Today it is already difficult to imagine how it is possible without a washing machine. But sometimes problems start. For some, the electronic module breaks down, while for others the washing machine does not drain the water to the end, for others it has stopped wringing out the laundry altogether. The latter case is the most common among the owners of automatic models lg, bosch, samsung, whirlpool, kandy and other brands, so it is worth considering in more detail. The reason why the drain function is disrupted can be eliminated on your own or by contacting a highly qualified service center specialist. Therefore, there is no reason to panic, and after reading this material, you will know what to do in such cases.

Drainage problems for samsung or another washing machine can be identified by a number of symptoms:

• slow drainage of water, and the subsequent mode starts with a malfunction;
• complete absence of drainage;
• draining is not done completely and not after each wash;
• after the wash cycle, the drain works, but not during rinsing;
• the machine stops pressing the laundry.

If the machine makes strange noises when draining, this is bad and cause for concern. It is necessary to inspect the equipment or call a specialist, without delay!

The drain will not work if a mistake has been made due to failure to follow basic precautions. For example, laundry is loaded in a larger quantity than provided for in the instructions for the washing machine. It is also worth considering another fact.Some lg washing machine models can be operated without draining. The first step is to check the condition of the drain hose for kinks and blockages. This also interferes with the full operation of the drain. If the reason why the drain is faulty is not found, it is worth moving on to a full inspection of the equipment.

People have been using washing machines for a long time and there is no one who would not know about them. And today, any workshop already knows, for example, why the kandy machine stopped squeezing out the laundry. As for the pressing problem, when there is no drain, the main reasons for this breakdown may be:

• clogging of the pipe;
• foreign objects entering the filter or pump;
• malfunction of the drain pump;
• clogged drain hose.

As world practice shows, every year millions of consumers are forced to contact service centers due to a malfunctioning washing machine. 2-3% of cases of malfunction are due to factory defects, 5% is the natural wear and tear of parts. Often, the cause of breakdowns is a perfect mistake when operating equipment of any brand (Candy, Samsung and others).

If you identify obvious malfunctions in the operation of the washing machine, do not panic, worry about what to do next and calculate the losses in advance. Perhaps the reason lies in some trifle. It does not hurt to read the instructions. It's just not easy to read, as many people do, putting it off for later, but to study it well. There will always be consumers who are “well versed” in how the washing machine works and think they can fix it. But it is already a big mistake to think so.

Before making an independent repair of the washing machine, for safety reasons, you must disconnect it from the power!

Any housewife can inspect the filter or check the drain hose. And to replace an inoperative pump is within the power of any man, at least somehow owning a tool. But if you have any difficulties, it is strongly recommended to contact the specialists. This article will just help you to determine the existing problem and find out whether you can fix it yourself or whether it is better to call a wizard.

Separately, it is worth mentioning what to do if the washing machine (Samsung, Indesit, Candy, Ariston) breaks down and is under warranty. Do not repair yourself! The answer to the question why it will be simple - the guarantee is lost. And if a breakdown happened during the warranty period, then you always need to contact the service center. If necessary, carry out repairs, in the service center it will be done free of charge. Any large company (whirlpool, indesit, samsung, kandy and others) has repair and service points in almost every city around the world.

Sometimes the washing machine suddenly stops spinning the laundry. Then you can try to interrupt the operation of the machine by pulling out the plug, and then start the same mode again. If there is no effect, the program can be interrupted with the buttons responsible for the rinse and spin modes. Even if this does not help, it may be due to electronics.

Incorrect operation of the electronic system of the washing machine causes the washing machine not to drain water. This is exactly the case when it is impossible to do anything here on your own, since you need to have the appropriate skills and knowledge. And even the slightest mistake leads to the failure of the entire machine. This is just such a case when the machine needs to be taken to a service center, where professionals will understand the electronics. Here it can be checked for operability, and if necessary, repairs can be carried out.

Any modern automatic machine (samsung, LG, bosch) of the latest model is distinguished by a more complex electronic system and a wide range of additional functions. Their diagnostics and repair are notable for their high cost. The same can be said about parts and assemblies. The repair of such equipment should not be postponed due to lack of funds.It is worthwhile to think carefully before buying a washing machine whether there are funds to fix it. And if the malfunction is not eliminated, then it will cause the failure of the entire unit. No matter how I have to buy a new typewriter.

The most common cause of poorly functioning drainage is a clogged filter. It is found in all automatic washing machines. There may be a small hose nearby, through which an emergency drainage of water is made.

When the filter becomes clogged, an error will appear on the control panel of the washing machine in the form of a corresponding code. Such a convenient function is found in many models of machines (Kandy, Bosch, Samsung and others). You can check the filter yourself. Usually it is located at the bottom of the case and can be covered with a panel, which can be removed in each machine in a different way. In bosch typewriters, it is enough to unscrew the screw and slide the cover to the side. But on older models of this brand there are hooks that need to be turned 90 degrees with a screwdriver. Ariston and Indesite washing machines use latches. On some models, you can simply push down on the panel or gently use a knife or flat head screwdriver.

Cleaning the filter is a must and should be done regularly! The frequency is indicated in the instructions.

Before unscrewing the filter, it is worth draining the water, and placing some container next to it, where the remaining water will drain or lay a rag. There are models where the filter can also be additionally fixed with screws. It is twisted counterclockwise. But if no one has touched it for a long time, it sticks to the rubber gasket, and it will take a lot of effort to remove it. Perhaps this fact was the reason for the bad drain.

Often coins enter the filter and completely block the flow. If no debris is found, you can spin the filter and check the drain operation again in spin mode. If the result does not change in a positive direction, then the cause of the malfunction should be looked for elsewhere.

Poor operation of the pump (impeller) may be the cause of the malfunction. This can be noticed if the machine hums strangely during operation. This means that there is thread or pile wrapped around the pump. This usually happens after a long period of use of the machine. This does not happen with new machines, but for reliability, the impeller can be checked.

Self-diagnosis is easy to carry out. The first step is to remove the filter and shine a flashlight on the hole. Then try to manually turn the impeller. If it doesn't spin well, it is clogged with something. If the rotation is free, then you can put the machine in spin mode. If the impeller is not moving, then there is a breakdown in the drain pump itself. But if the drain still does not work, and the inspected parts are in order, then you should continue to search for the causes of the malfunction.

If it became clear that the pump is not working, then it will not be difficult to replace it. Most brands of washing machines are equipped with a pump of a standard design and there should be no problems with buying a new part. If necessary, you should contact the seller for advice.

Usually, it is not required to completely disassemble the washing machine, but it all depends on the specific model (kandi, whirlpool, samsung and others). The defective part is removed, disconnected from the wires and a new one is put in its place, not forgetting to connect the power. The main thing is to remember the sequence of work and carry out the assembly in the reverse order.

Someone asks how the hose can affect the drain? The point is in the design of the hose, which is a valve that prevents water from flowing out of the tank during the washing process. Perhaps a mistake in the installation of the hose does not allow the pump to cope with the work. This can happen when the machine is moved to a new location and the hose is above the water level. The washing machine must inform the owner of this.

To make sure that this is not the reason for the inoperative drain, you need to disconnect the hose from the sewer and lower it into the basin. After that, start the washing mode, and when the tank is a little full, switch the machine mode to drain. If the water has gone, then it is enough to adjust the height of the hose attachment, otherwise the attachment will have to be removed. In some models, this is easy, while others have to be disassembled.

When the hose is disconnected, it is worth checking it for its ability to pass water. If necessary, clean it or even replace it. At the same time, the branch pipe should be checked, it may also be dirty.