Monitor DIY repair samsung

It so happened that once the screen of the Samsung 740N monitor, which has faithfully served me for almost 11 years, suddenly went out almost immediately after turning it on. Other attempts to enable and disable were unsuccessful, because according to the signals from the sound card, the operating system was booted successfully, it became clear that the problem lies in the monitor. Of course, a radio amateur cannot so easily throw out an old electronic device without trying to fix it, well, or raskurochit broken device for parts, then how it goes.

A quick search [1-6] showed that the most common problem with monitors of this type is the failure of electrolytic capacitors in the power supply. In general, even the most novice radio amateur can do such repairs, so you can get by with the purchase of several radio components at the place of purchase of the monitor, which is a couple of orders of magnitude cheaper, the cost of your own time, of course, is not taken into account. But in order to repair something, you first need to get inside the monitor, do it carefully, without marks on the case, perhaps the most difficult part of the repair. First you need to put the monitor face down, so that the surface of the screen would not be damaged, after that you should unscrew the screws holding the stand.

The back cover of the monitor is held by latches located around the perimeter of the monitor case. To open the latches, insert a strong thin object, such as an unnecessary plastic card or a metal ruler, into the gap between the screen frame and the back cover, and then sequentially and slowly unscrew all the latches holding the cover. Under the back cover, such a spectacle appears before us. In the next photo, the cover that covers the power connectors of the backlight lamps is also removed.

It should be noted that the metal casing visible in the photo above, to which most of the structural elements are attached, is fixed in the desired position with the help of the back cover and is not fixed to anything else. Before further disassembling the monitor, carefully document the wiring of all internal connectors. True, a real chance to confuse the connectors exists only for the power connectors for the backlight lamps.

Just in case, we fix the position of the remaining connectors.

Now, from the actual screen, you can remove the casing with the printed circuit boards fixed in it.

Then we remove the power supply board.

As expected, three failed electrolytic capacitors are visible on the board.

Finally, we disconnect the power supply board and remove the protective film that covers the board from the side of the printed conductors, this film is held on 3 plastic clips.

In addition to the obviously failed capacitors, a number of sources reviewed recommend replacing the capacitor C107 for preventive purposes.

This radio part has been replaced with a 47 μF x 250 V capacitor.

Just as the reviewed sources indicated, the fuse F301 breaks down along with the capacitors. In the photo, this is a green radio component, which is visible next to the swollen electrolytic capacitors.

We remove suspicious and clearly damaged radio components from the board. The main culprits are that the author of these lines was left without a computer on May 9, 2017.

In place of the failed radio components, we install similar capacitors. Instead of a 3 A fuse, a 3.15 A fuse with solder leads is installed.

After assembly, the monitor's performance was fully restored, after three weeks of intensive use, no deviations were noticed in the work. The author of the material is Denev.

Here are the TOP 10 most common LCD monitor malfunctions that I felt the hard way. The fault rating was compiled according to the author's personal opinion, based on the experience of working in the service center. You can take this as a universal repair manual for almost any LCD monitor from Samsung, LG, BENQ, HP, Acer and others. Here we go.

I divided the malfunctions of LCD monitors into 10 points, but this does not mean that there are only 10 of them - there are many more, including combined and floating ones. Many of the breakdowns of LCD monitors can be repaired by hand or at home.

in general, although the power indicator may be blinking. At the same time, twitching the cable, dancing with a tambourine and other pranks do not help. Tapping the monitor with a nervous hand usually doesn't work either, so don't even try. The reason for such a malfunction of LCD monitors is most often the failure of the power supply board, if it is built into the monitor.

Recently, monitors with an external power source have become fashionable. This is good because the user can simply change the power supply in the event of a breakdown. If there is no external power source, then you will have to disassemble the monitor and look for a malfunction on the board. In most cases, it is not difficult to disassemble an LCD monitor, but you need to remember about safety.

Before fixing the poor fellow, let him stand for 10 minutes, unplugged. During this time, the high-voltage capacitor will have time to discharge. ATTENTION! DANGEROUS TO LIFE if the diode bridge and the PWM transistor burn out! In this case, the high voltage capacitor will not discharge in an acceptable time.

Therefore, EVERYONE before repairing to check the voltage on it! If a dangerous voltage remains, then the capacitor must be manually discharged through an insulated resistor of about 10 kOhm for 10 seconds. If you suddenly decide to close the terminals with a screwdriver, then keep your eyes away from sparks!

Next, we proceed to inspect the monitor power supply board and change all burned-out parts - these are usually swollen capacitors, blown fuses, transistors and other elements. It is also MANDATORY to solder the board or at least inspect the soldering under a microscope for microcracks.

From my own experience I will say - if the monitor is more than 2 years old - then 90% that there will be microcracks in the soldering, especially for LG, BenQ, Acer and Samsung monitors. The cheaper the monitor, the worse it is made at the factory. Up to the point that the active flux is not washed out - which leads to the failure of the monitor after a year or two. Yes, yes, just when the guarantee ends.

when the monitor is turned on. This miracle directly indicates to us a malfunction of the power supply.

Of course, the first step is to check the power and signal cables - they must be securely fastened in the connectors. A blinking image on the monitor tells us that the monitor backlight voltage source is constantly jumping off the operating mode.

The most common reason for this is swollen electrolytic capacitors, microcracks in the solder and a faulty TL431 microcircuit. Swollen capacitors most often cost 820 uF 16 V, they can be replaced with a larger capacity and a higher voltage, for example, the cheapest and most reliable ones are Rubycon 1000 uF 25 V capacitors and Nippon 1500 uF 10 V capacitors. 105 degrees) Nichicon 2200 uF 25 V. Everything else will not last long.

after the time has elapsed or does not turn on immediately. In this case, again, three frequent LCD monitors malfunctions in order of frequency of occurrence - swollen electrolytes, microcracks in the board, faulty TL431 microcircuit.

With this fault, a high-frequency squeak of the backlight transformer can also be heard. It usually operates at frequencies between 30 and 150 kHz.If the mode of its operation is violated, oscillations can occur in the audible frequency range.

but the image is viewed under bright light. This immediately tells us about a malfunction of LCD monitors in terms of the backlight. In terms of the frequency of occurrence, it could be put in third place, but it has already been taken there.

Option two - either the power supply and inverter board burned out, or the backlight lamps are faulty. The latter reason is not common in modern monitors with LED backlighting. If the LEDs are backlit and fail, then only in groups.

In this case, there may be a darkening of the image in places at the edges of the monitor. It is better to start repairs with diagnostics of the power supply and inverter. An inverter is the part of the board that is responsible for the formation of a high-voltage voltage of the order of 1000 volts to power the lamps, so in no case should you try to repair the monitor under voltage. You can read about repairing the Samsung monitor power supply in my blog.

Most monitors are similar in design, so there shouldn't be any problems. At one time, monitors simply rained down with a breakdown in contact near the tip of the backlight. This is treated by the most careful disassembly of the matrix to get to the end of the lamp and solder the high voltage wires.

If the backlight itself burns out, I would suggest replacing it with the LED backlight bar that usually comes with your inverter. If you still have questions - write to me by mail or in the comments.

These are the nastiest LCD monitor malfunctions in the life of any computer technician and user, because they tell us that it's time to buy a new LCD monitor.

Why buy new? Because your pet's matrix is ​​90% unusable. Vertical stripes appear when the contact of the signal loop with the contacts of the matrix electrodes is broken.

This can only be cured by careful application of anisotropic adhesive tape. Without this anisotropic glue, I had a bad experience repairing a Samsung LCD TV with vertical stripes. You can also read how the Chinese repair such strips on their machines.

An easier way out of this unpleasant situation can be found if your brother-in-law friend has the same monitor lying around, but with faulty electronics. It will not be difficult to blind from two monitors of similar series and the same diagonal.

Sometimes even a power supply unit from a monitor with a larger diagonal can be adapted for a monitor with a smaller diagonal, but such experiments are risky and I do not recommend starting a fire at home. Here in someone else's villa - that's another matter ...

Their presence means that the day before, you or your relatives had a fight with the monitor because of something outrageous.

Unfortunately, household LCD monitors do not provide shockproof coatings and anyone can offend the weak. Yes, any decent poke with a sharp or blunt object into the LCD monitor matrix will make you regret it.

Even if there is a small trace or even one broken pixel, over time, the spot will begin to grow under the influence of temperature and voltage applied to the liquid crystals. Unfortunately, it will not work to restore the dead pixels of the monitor.

That is, there is a white or gray screen on the face. First, you should check the cables and try connecting the monitor to a different video source. Also check if the monitor menu is displayed on the screen.

If everything remains the same, we look closely at the power supply board. In the power supply unit of the LCD monitor, voltages of 24, 12, 5, 3.3 and 2.5 volts are usually formed. You need to check with a voltmeter if everything is in order with them.

If everything is in order, then we carefully look at the video signal processing board - it is usually smaller than the power supply board. It has a microcontroller and auxiliary elements. You need to check if food comes to them. With one probe, touch the contact of the common wire (usually along the contour of the board), and with the other, go over the terminals of the microcircuits.Usually food is somewhere in the corner.

If everything is in order in the power supply, but there is no oscilloscope, then we check all the monitor loops. There should be no carbon deposits or darkening on their contacts. If you find something, clean it with isopropyl alcohol. In extreme cases, you can clean it with a needle or scalpel. Also check the ribbon cable and the board with the monitor control buttons.

If all else fails, then perhaps you are faced with a case of a failed firmware or a failure of the microcontroller. This usually happens from surges in the 220 V network or simply from aging of the elements. Usually, in such cases, you have to study special forums, but it is easier to start up for spare parts, especially if you have a familiar karate fighter fighting against objectionable LCD monitors.

This case is easily treated - you need to remove the frame or the back cover of the monitor and pull out the board with buttons. Most often, there you will see a crack in the board or in the solder.

Sometimes there are faulty buttons or a loop. A crack in the board violates the integrity of the conductors, so they need to be cleaned and soldered, and the board must be glued to strengthen the structure.

This is due to aging of the backlight lamps. According to my data, LED backlighting does not suffer from this. Deterioration of the parameters of the inverter is also possible due to aging of the constituent components.

This is often due to a bad VGA cable without an EMI suppressor - a ferrite ring. If replacing the cable does not work, then power supply interference may have entered the imaging circuits.

Usually they get rid of them schematically by using filtering capacities for power supply on the signal board. Try to replace them and write to me about the result.

This completes my wonderful rating of the TOP 10 most common LCD monitor malfunctions. Most of the breakdown data is collected from repairs of popular monitors such as Samsung, LG, BENQ, Acer, ViewSonic and Hewlett-Packard.

This rating, it seems to me, is also true for LCD TVs and laptops. What is your situation on the LCD monitor repair front? Write on the forum and in the comments.

The most common questions when disassembling LCD monitors and TVs - how to remove the frame? How do I release the latches? How to remove the plastic from the case? etc.

One of the wizards made a nice animation explaining how to disengage the latches from the chassis, so I'll leave it here - it will come in handy.

To view animation - click on the image.

Recently, monitor manufacturers are increasingly completing new monitors with external power supplies in a plastic case... I must say that this makes it easier to troubleshoot LCD monitors by replacing the power supply. But it complicates the operating mode and the repair of the power supply itself - they often overheat.

I showed how to disassemble such a body in the video below. The method is not the best, but it is fast and can be done with improvised means.

They brought 2 samsung monitors for repair - 940n and 740n. Most often, these devices have problems with the power supply, but, interestingly, there are several modifications of these same blocks for the forties. Our guys got one modification for both seventeen and nineteen inch models. Accordingly, we will describe the repair of this modification here.

The first thing to do is to look at the display from different angles (preferably with the D-SUB cable disconnected, which VGA goes to the video card). If it is noticeable that the inscription “cable not connected“Then this is our patient. The backlight does not work for the patient, and everything else is normal.

Of course, in order to fix this beast, it needs to be disassembled. This is done quite simply - remove the leg and half the body. I half the body using this blue piece that looks like a pick (photo below). You can buy it in most radio markets and one such thing costs about 15 rubles.It is not suitable for any technique, but for both monics, one such was enough for me.

After all the latches are unhooked, put the monitor with the display down and remove the plastic cover. The next step is to remove the casing that protects the wires going to the backlight lamps and unhook the loop 2, circled in blue. The cover can also be removed easily with a small, thin, flat screwdriver. After removing the casing, we detach the wires supplying the backlight (pictured below).

Before you start repairing a monitor that suddenly does not work, it would be a good idea to first figure out what an LCD monitor consists of.

In the LCD monitor, the main blocks can be distinguished:

• power unit
• inverter unit
• control and imaging unit
• button block
• matrix

Designed to generate stable voltages (+12 V, +3 V or +5 V). Typically, this unit breaks down most often due to capacitors.
Capacitors lose their capacity and swell. Because of this, the voltages become unstable. The moment the monitor turns on, the protection is triggered, or there is not enough voltage to start.
Defective capacitors are almost always swollen and immediately visible on visual inspection. But when replacing capacitors, I recommend changing everything at once. Sometimes capacitors do not swell but lose their capacity.
Faulty capacitors are not the only power supply failure. But other malfunctions are very rare and I have not personally encountered them yet.

Power supply malfunctions can be expressed:
1. The monitor does not respond to the power button
2. The monitor lights up for a few seconds and goes out
3. Along with these manifestations, a whistle is heard

For detailed disassembly of the monitor and repair of the power supply, you can find an example LCD monitor Samsung SyngMaster 940BF

Responsible for backlight lamps. Typically, a lamp inverter has two channels of two lamps. Rarely one or four. In photo 1 they are shown in red circles.

Lamp inverter malfunctions can be expressed as follows:
1. The backlight of the monitor turns on for a few seconds and goes out
2. The monitor turns on, but there is no backlight at all. In this case, if you shine a small flashlight on the monitor, you can see the image. Thus, the monitor works - the backlight does not work.

You can read about matrix damage in LCD monitors here

Publication date: April 5, 2014

Today I will tell you how to repair an inverter with your own hands.

If your monitor has a defect that it turns off after two to three seconds after being turned on, and at the same time the image appears at the time of turning on.

A trance defect can be determined by a device for short-circuited loops, by resistance.

Usually one of the trances breaks. This is, in principle, a disease of monitors.

The simplest option, in the absence of a trance, is to install a new inverter, of which there are many on sale.

A detailed examination revealed a defect in one of the inverter trances. It is easy to check this: you need to try the working candle one by one, first at the exit of the first trance, then the second, and so on alternately. In a non-working trance, the candle will naturally not light up at the moment of switching on.

Without going into details, we solder the transformer of the TMS91429CT inverter so that the protection does not work.

After dismantling the trance, it will look like this:

Then we take a ready-made inverter, for the same number of candles (4 candles), which are freely sold on radio markets, radio stores, etc., such as: model SF - 04S402, dimensions: 135-45 mm. Or something similar, the main thing is to fit the inverter in size.

Next, we supply it with power and control, place it with Velcro in a convenient place. It may be necessary to increase the length of the wires from the lamps to the output of the inverter.

Here are some examples of inverter placement.

And here are examples of ready-made inverters.

It will not be difficult for a person to disassemble.