Inflatable pool DIY repair

In detail: do-it-yourself inflatable pool repair from a real master for the site my.housecope.com.

When the long-awaited summer comes and the thermometer shows "heat!" Modern inflatable and frame water tanks have a low price, are easy to install and operate. You can choose a pool for every taste in terms of diameter, height, color and design. Most products are made from polyvinyl chloride (PVC). The disadvantage of this material is that it can be punctured relatively easily.

It would seem that the hole in the pool is a puncture in the rest. But this is not the case. Any hole, even a large one, is not a reason to throw the product away. There are many ways to glue an inflatable pool with your own hands.

If the pool has begun to deflate, then you should not wait until it finally descends. The air remaining in it must be used to find the puncture site. There may be several holes, so the entire product must be carefully inspected. Several methods of puncture detection can be used.

- One by one, each ring filled with air should be immersed in a container of water. The hole can be detected by the bubbles that form the air escaping from it.

- If the pool is large, which makes it difficult to move, then you can look for a puncture in a different way. Using laundry soap and water, beat the lather and apply it to the well-filled rings of the pool. Air escaping through the hole will form bubbles.

- If a puncture is formed in the bottom of the pool, then it can be found there as well. To do this, you need to raise the structure and turn it towards the sun. Looking at the bottom of the pool, turned towards the luminary, you can easily find even small holes in it.

Video (click to play).

After the punctures in the product are found, they must be marked with a marker.

1. This method can be called "emergency". It is suitable for the case when there is nothing else at hand, and the store is far away or lazy. The main material of this pool repair option is ordinary office tape. Adhesive tape can only be used to repair an inflatable product if “there is no strength, how you want to swim. ". This method is completely unreliable: a quick-and-dirty patch will last a maximum of a week, after which it will safely peel off from the presence of constant moisture. But this repair method is good because you don't even need to drain the water from the pool. Before sticking a piece of scotch tape on the puncture site, it is necessary to treat the surface near it with either very fine sandpaper ("zero"), or wipe it with an alcohol solution (you can use vodka). It is better not to use a solvent for these purposes, because it can corrode the PVC material. After all the procedures, we cut off a piece of scotch tape of the required size and glue the hole.

2. This option for repairing the pool can be called "materials at hand". It perfectly combines a frame pool and glue "Moment" and "second". First we find the puncture site, then dry the surface around it (a hairdryer will work well). The patch can be cut from thin rubber, thick oilcloth and a piece of thin dermantine. We thoroughly clean and degrease the surface. After that, we apply glue to both gluing surfaces (patch and pool). You need to work with the second glue carefully and quickly so as not to stick your fingers to the structure. But with "Moment" it is more sedate: it is necessary to wait 3-5 minutes for the glue to react with the material of the patch and PVC, and only after that we glue their surfaces.After that, with sufficient force, we press the patch to the surface of the pool and hold it for several minutes. When gluing, you need to remove air from under the patch and make sure that it fits snugly against the pool wall. To achieve a reliable result, you need to press down the bonding site with something heavy and leave to dry for 12 hours.

3. A method that will certainly suit not just motorists, but the people who repair them. It is they who necessarily have a set for cold vulcanization of chambers in the garage. This repair can certainly be called "capital". To install the patch by vulcanization, first clean the puncture site with sandpaper, then degrease it. A special material for the patch is taken, a piece of the required size is cut out and the protective layer is removed. Then the patch is pressed against the surface of the pool. The best, of course, is to fix the glued place with something heavy for a long time.

4. Method according to the instructions supplied with the product. There are special kits for repairing the pool surface, which include a PVC patch and a small tube of special glue. But, this miracle - the set is not included with the pool, you need to buy it separately. This repair option is similar to method number 2: a thin layer of glue from a tube is applied to the dry cleaned surface of the pool. A patch is cut out of the prepared PVC material and pressed against the puncture with force, and then fixed with something heavy until it dries completely.

5. There is also the most reliable way to seal an inflatable pool - it is to contact a specialized company for the repair of such products. There are workshops in cities that provide similar repair services. Alternatively, you can try asking a tire shop for help.

The best way to repair a pool is to avoid a puncture in the pool shell. This can be achieved only by strictly observing the simple rules for operating the product.

- Do not open the package with the product with sharp objects, this can damage the material from which the pool is made.

- Try to install the pool away from bushes and trees, branches of which may puncture its surface.

- The misconception that the circles need to be inflated very strongly. Due to the strong pressure, the PVC material may not withstand and disperse.

- It is better not to leave the inflated inflatable pool in direct sunlight. The sun will heat the air inside the product, the pressure will rise and PVC will not withstand the load. If the pool will be in an open area, then it should be slightly lowered.

- Be sure to lay a substrate under the bottom of the pool. This will protect the bottom from sharp objects.

- Watch out for pets that have sharp teeth and claws.

- It is imperative to clean the pool, because dirt destroys the material from which the product is made.

- Do not jump on the inflatable pool rings.

Inflatable pools are one of the most favorite attractions for children in the summer, while adults appreciate them for the convenience of transportation, assembly and, of course, for a low cost. With their help, you can organize fun children's leisure in the country, at the sea, by the river.

But the material from which the pools are made is easily damaged. Cuts and punctures appear, air begins to escape, as a result, the pool does not hold its shape and is quickly deflated.

Then the question arises, how to seal a children's inflatable pool.

What is required for the repair:

Marker,
A container with water,
Reinforced tape,
Cold vulcanization set,
Fine sandpaper,
Rubber patch,
Soft brush,
Laundry soap,
Inflatable pool adhesive TRS 2002.

How to glue an inflatable pool

The repair method is selected based on the material from which the pool is made. It can be rubberized fabric, PVC, rubber.

But in any case, you need to start by looking for the place where the puncture appeared. To do this, the pool is pumped up and placed in whole or in parts into a container with water.
Bubbles will begin to emerge from the hole. It is marked with a marker.
If the result is needed quickly, you can do with scotch tape. The place is cleaned with sandpaper, a piece of scotch tape is cut off, then glued. Enough of such repairs for a period of no more than a week.
For a better result, patches are used, which are sold in car kits for cold vulcanization of cameras.

The place is also cleaned with fine sandpaper, the protective layer is removed from the patch and fixed with a clamp to the area with a cut.
The clamp can be removed after an hour.
Special glue is used to repair the rubberized fabric.

If you cannot fix the problem on your own, you should contact the company where this pool was purchased. Some manufacturers include a repair kit that may include patches, glue, and instructions.

Inflatable rings are fun for children. They make bathing interesting, help the child to stay on the water. Today the choice of swimming rings is huge, there are both inexpensive options and more durable and high quality ones.

But no matter how expensive this toy is, sooner or later it begins to release air due to the cuts that appear. It is almost impossible to avoid them with small children, so it is important for parents to know how to glue the circle. In this case, you need to find the place of the cut and carefully remove it.

You need to start by looking for the damaged area. To do this, the circle is inflated and lowered into the water.
Air will begin to come out of the holes, at this moment they need to be marked with a felt-tip pen or pen.
It is recommended to use the same material from which the circle itself is made as patches. For example, you can take a toy that is no longer in use, or buy special repair kits for inflatable products with patches.
The shape of the patches should be rectangular, but with rounded corners.
The size should be such as to completely cover the damaged area.
In the next step, the place where it will be applied glue for an inflatable circle Cruiser or Intex, treated with acetone or alcohol to improve the adhesion of the glue to the surface.
But since acetone can compromise the integrity of the material, it is recommended to first test it on a patch.

Unlike rubber, PVC is not required to sandpaper. It is not recommended to use "Superglue" as an adhesive for repairing PVC circles, as it will crack on this material.

The application of the adhesive must be carried out according to the manufacturer's instructions. Most often, it is applied to both the patch and the damaged area. For some formulations, one coat will be sufficient, for others, reapplication may be required.

Next, the patch is applied to the circle, holding it with your hands so that the material does not wrinkle. Use your thumbs to smooth it out, removing air.

For an hour, the toy is not inflated so that the glue seizes, then it can be inflated loosely and left in this position for a day until it dries completely.

It should be borne in mind that inflatable rings in the form of animals break the fastest, since they have a lot of connecting seams and parts.

There are inflatable beds in almost every home. It is convenient to use them when guests arrive and additional berths are required. But, like any other inflatable thing, the bed can fail. Their integrity is often violated by pets, children or misuse. As a result, the mattress begins to deflate. But you shouldn't throw it away, you can try to repair it.

VIDEO

We recommend the following glue options: Uranium, Intex.

First you need to find the place of damage and straighten it on a flat surface.

Then prepare a tape of transparent material and glue.In no case should it be an ionocrylate compound or super glue, which will not give the desired result. You can use the compositions intended for the repair of inflatable products.

The place of damage is treated with alcohol or acetone and the patch is “tried on”, marking the place of gluing with a pencil. Then the patch is trimmed to the desired size, preferably to an oval or round shape, with a margin of 3-5 cm compared to the cut area.

Glue is applied to the damage site and to the patch and spread with a brush. After the first layer has dried, the second is applied. Then, using an ordinary hair dryer, the glue on the surfaces is heated and applied to each other. To remove air, use a roller or improvised objects in the form of spoons, cans. After that, the bed can be folded without bending the glued place and left for a day.

Not everyone knows how to glue an Intex inflatable bed. Although this manufacturer usually applies a special repair kit to inflatable products, which includes instructions, glue and patches. By following the manufacturer's instructions, you can easily get rid of minor defects at home.If the air bed is still allowing air to pass through, then there is still damage. In difficult cases, it is worth contacting the specialists from whom the bed was purchased so that they can help eliminate defects.Do you have a pool on the property? Great, you can be glad for your leisure time - on any warm day, a reservoir is at your side, which means you can always refresh yourself! However, the pool, whatever one may say, is not a natural body of water created by nature for centuries. And in it, alas, something can break sooner or later. If you have such a situation, it does not matter, in this article we will tell you about the features of repairing swimming pools of various designs. Image - DIY inflatable pool repair

Of course, the inflatable structure is limited in many ways. But which pool is the easiest to install, the easiest to maintain and the most affordable? Inflatable, of course. They are small and large, deep and not very deep. In general, a good inflatable pool in terms of its internal volume may not be inferior to, for example, a stationary one. But its most important plus is that it can be easily transferred to a new place. After all, it is inflatable, which means that it is enough to drain the water from it, release the air, roll it up, and even the largest pool quietly moves to a new site by one or two people. And there, if the platform is flat, it unfolds, inflates and refills with water in just one or two hours.

But everything would be simple if it were not for this “if the site is flat”. The fact is that the inflatable pool does not have its own rigid frame. It, being inflatable, becomes sufficiently stable in terms of its geometry only when it is fully filled with water. When it is already installed and inflated, but not yet filled, it easily bends in all directions. And of course, if the base for the pool is not even horizontally, when pouring water, it begins to tilt in the direction where the angle is lower than other corners. Therefore, the installation of the pool always requires leveling the site.

It is also optimal to cement the site or at least lay plywood, boards or just PVC film under the bottom of the pool. After all, an inflatable pool does not have its own hard bottom, its material is thin and fragile, which means that any knot forgotten on the site under the pool, and just a sharp pebble, can simply pierce it when filling the pool. Most of the breakdowns of inflatable pools are connected with this.

The technology is very clear to any bicycle owner. After all, the basis of an inflatable pool is, as a rule, PVC, that is, a very easily glued material. First, find the place of the gap. To do this, inflate the pool and listen to where the air comes out with a whistle. The place of the gap is outlined along the contour with a marker or felt-tip pen.After that, it remains to put the rivet. There are only two rivet options.

The first is a simple external patch. It is used when the size of the hole is small, no more than a few centimeters in cross section. In this case, the edges of the hole are cleaned with sandpaper, degreased with kerosene, gasoline, alcohol or solvent. Do the same with the patch - with the side that will be glued to the pool material. The patch is usually made of the same material as the walls of the inflatable pool. After that, a thin layer of glue is applied along the contour of the hole and on the cleaned side of the patch, let it dry for several minutes, then apply the patch and press the two layers to be glued together as much as possible. Then comes drying, and - you can reuse the pool. If it is glued correctly, in accordance with the technology described on the label of the glue used, such a patch will not "pass".

The second option is a complex patch stitching the hole. This method is used when the size of the hole does not allow it to be sealed with one small patch. In this case, a number of nuances are added to the repair technology. First, the hole is sewn with any simple stitch with a strong thread. The seams are carefully coated with glue. This is followed by a patch installation similar to the first technology.

A fairly popular option for a pool, especially recently, is a frame structure. It is a “skin” made of durable fabric material stretched over a frame made of metal or polymer supports.

Usually, PVC cloth is used as the material for the skin, which is sealed and durable material. Handled correctly, it can last for years, but it is just as prone to cuts and tears as inflatable pool material. Accordingly, the repair of frame pools is carried out using the same technology. A patch is applied to the place of the gap - either a simple one, or with a hole stitching up. It is very important to use a suitable adhesive for this. For example, the glue "moment", known to every of our compatriots, is also suitable here, but not any - only those modifications, the instructions for which indicate the applicability for gluing PVC.

If the frame pool is damaged more seriously, for example, it has a broken support post, then self-repair of such a breakdown is hardly advisable. It's easier to contact the company that sold you the pool. Surely they have spare parts for just such a case.

Unlike inflatable and frame pools, stationary pools are a serious engineering structure. Accordingly, there can be much more breakdown options here. They usually come down to two types.

The first, and most common, is a breakdown of the drainage system. Such a system includes several elements - a water supply, a pump for pumping out water and a filtration system. Failure of one of the systems or its clogging leads to the fact that the water stops regularly circulating in the pool. And this entails the appearance of algae and water decay, that is, it is no longer worth using such a pool. It is optimal to involve experienced specialists in repairing these elements.

The second type of breakdown is associated with a violation of the tightness of the walls and bottom of the pool. Either the tiles are cracked, or the seams between the tiles are leaking, as a result of which water from the pool is constantly leaving. And in this case, of course, it is better to involve professionals.

However, if your pool is broken, and you are going to carry out repairs with your own hands, first of all, drain the pool bowl by draining all the water from it. Next, you need to decide what exactly the breakdown consists of. If this is a blockage, then the actions here are the same as when clearing blockages in the sewer. If pumping or filtering equipment breaks down, replace it.If the bowl leaks, use a building mixture similar to the one used for laying the bowl to restore tightness.

Rest at the cottage brings maximum pleasure if a swimming pool is installed on the site. During operation or due to mistakes made during installation, various breakdowns may appear. It is possible to repair some of them with your own hands, while saving a lot of money.

The most common breakdowns include:

• burnout of the backlight (searchlight);

• insufficient air conditioning.

If we are talking about the failure of hydraulics, then it is recommended to involve specialists in the repair work. To fix such a malfunction, you will need deeper knowledge and equipment, which a common man in the street does not have.

The bowl repair technology is simple, everyone can master. You should start work by inspecting the surface. It is worth conducting an audit carefully so as not to miss minor deformations.

Before eliminating the detected flaws, you need to determine the cause of the breakdown in order to avoid repeated damage.

Among the main provoking factors:

• incorrectly laid waterproofing, low-quality waterproofing film;

• poor preparation of the object for wintering;

• lack of an insulating layer or insufficient thickness of the heat insulator;

• mistakes made when laying communications.

To prepare the pool for the warm season, the following amount of work should be done:

• clean minor damage from finishing and seal cracks with a special putty;

• treat with waterproofing material;

• apply a layer of liquid glass to all surfaces of the bowl;

• after drying the walls, treat with a primer or sealant;

• lay tiles or mosaics.

Concrete matures for at least 28 days. During this time, it is necessary to moisten the surface to prevent the formation of cracks. It is also worth creating protection from direct sunlight on the walls of the bowl.

If strong destruction of the concrete bowl is revealed, it is recommended to make a secondary concrete pouring. To do this, the entire surface is cleaned of wobbly elements, treated with soil, after which the formwork is created.

The concrete layer must be at least 5 cm. Further work includes treatment with waterproofing, liquid glass and finishing material, if any.

The parameters of the concrete used:

To prepare one cube of concrete solution, you need to take 600 kg of cement, 150 kg of medium-fraction sand (cleared of debris), 700-900 grams of a ton of fiberglass, 1 kg of plasticizer and water.

If the destruction has touched the reinforcing layer of the bowl, then a major overhaul will be required, providing for the installation of new reinforcement, pouring concrete, processing (with waterproofing material and liquid glass), as well as finishing.

Do not try to reanimate dilapidated structures that leak from all sides. It is easier to dismantle and build a new pool. The collapsing bowls have communications in disrepair, so partial repairs will turn out to be a waste of time.

Slow drainage of water is obtained as a result of non-observance of the rules for arranging water supply lines. This may be an insufficient slope of the main line when laying sewage drains, the use of low-quality metal pipes, which begin to flow and silt during the heat process. Even when using plastic pipes, there is a reality of leakage if the connections are bypassed.

If a complete replacement of the pipeline is planned, it is recommended to use polypropylene pipes. Alternatively, choose a high quality PVC-U, LESSO pipe.

The product compares favorably with analogues in the following advantages:

• simple installation with connecting elements of the same brand;

• inertness to aggressive environments;

Inflatable pools are made of rubber or PVC. It is necessary to select the glue for eliminating the hole, taking into account the type of material.In some cases, on the packaging of the pool, the manufacturer gives recommendations on the choice of an adhesive composition for repair work.

Specialty stores offer glue and patch kits and liquid patches. In any case, the glue mixture must be waterproof, otherwise the hole will quickly depressurize. Another important advantage of the adhesive composition is the drying speed.

• Intex set (specially designed for inflatable mattresses, swimming pools).

The sequence of repair work:

• degrease the surface with an alcohol solution;

• sand both sides of the gluing with fine sandpaper;

• Apply glue to the surface and patch and press down with a heavy object for 1 hour.

If it is difficult to determine the location of the damage in the pool, you need to inflate it and lower it into the water. In the place where the bubbles form, there is damage.

When choosing an inflatable pool for a summer residence, everyone naturally chooses:And he looks at the manufacturer of the product. If the manufacturer is well-known, then there is no need to be afraid - your inflatable pool will last a long time and without problems. This happens if there is no mechanical damage from the outside: cuts, punctures, seams divergence. Then the tightness of the pool is zero, the water flows out, and it is simply impossible to take any water procedures. What to do? Of course, you can buy a new pool. But if there is no money for an unexpected purchase, then it is better to repair the pool at home. How to seal the inflatable pool if it started to leak? Find out from our article how to seal an inflatable pool at home.The most popular manufacturers of inflatable pools are INTEX, Wehncke, Zodiac, Bestway, Polygroup. Image - DIY inflatable pool repair

If a puncture hole is formed on the surface of the pool - 1-2 mm, and you do not know how to seal the inflatable pool, then it is advisable to just drip a good sealant or waterproof glue, for example "Moment", onto the damaged area. Allow the glue to dry and reapply the sealant to the puncture site. After this, the pool will not deflate. If the damage is more extensive - for example, a 2-5 cm cut, then in order to seal the inflatable pool at home, you will need:

sealants from well-known manufacturers;
waterproof types of glue;
a piece of rubber or rubberized fabric with an area 2-3 cm larger than the area of the cut;
you can use polypropylene materials;
tarpaulin;
any waterproof fabric.

Cover the cut with glue or sealants.
Cover a rubberized sealed cloth or other material on one side with a layer of sealant.
Press firmly a piece of sealed material against the cut.
Hold under pressure for as long as written in the instructions for use of the glue or sealant.
After drying, experts recommend once again applying a layer of sealant on top of the patch.
Let dry.

Read also: DIY carburetor 2108 repair

ADVICE! Remember, it is better to choose an adhesive patch from the same material (or approximately the same) as the material of the pool. The most commonly used materials are vinyl, polystyrene and rubberized fabric.

Depending on how high-quality the sealants, glue and waterproof material were, the further service life of your inflatable pool will depend.

If the question arises, how to glue a children's inflatable pool, it is better to use vinyl material. But if the pool is small, scotch tape, polyethylene and any polymer will do. For reliability, after gluing on top of the damaged area, apply a layer of sealant.

The market today offers a huge number of adhesives, on which it is written "Adhesive for inflatable pools". Use it and your mini pond will save you from the heat for years to come.

IMPORTANT! Do not use Moment glue to repair inflatable pools. It will damage the material even more. At home, BF-4 glue is most often used.But don't mix it up! BF-2 glue will not work - it is too hard. Therefore, the gluing site will wrinkle and be conspicuous.

You can seal the inflatable pool with the patches that come with some types of pools - the same color and from the same material. Such a hermetically and tightly glued "native patch" will not be visible on the surface of the pool. In addition, in online stores you can find special pictures or designs on sealed fabrics and materials that, when glued, will only decorate your pool, give it originality. Then, also by sealing the damaged surface of the pool and the picture, you can only decorate your home pond.

IMPORTANT! To place a pool with a volume of 4 cubic meters. will require approximately 6 sq. Do not forget about a convenient approach at least from one side. This is another 2 - 3 sq. If you have a standard plot of 6 acres, then you will have to sacrifice part of the beds.

Of course, everyone dreams that his inflatable pool was:

Before buying, we get acquainted with the instruction manual, where all the nuances of using the pool are spelled out. But we don't always listen to advice. Avoid contact of the pool surface with:

piercing objects;
cutting;
sharp;
branches and twigs;
pens and pencils.

To do this, the pool should be located away from all branches and construction equipment on a flat sand cushion - without branches and debris. Do not give children any sharp or pointed objects (it can even be a Spiderman, transformer toy) when they are swimming in the pool.

The pool must be filled in accordance with its parameters and instructions. With an excessive amount of water, defects in the form of divergence of the pool seams can also occur. And the distance from the barbecue area will ensure that the spark does not hit your pool and make it completely unusable.