We disassemble the Nokia 8800 phone.
This article is not a guide to action! You are solely responsible for collecting and disassembling your device.
1-2.) Always stick a protective film on the display glass.
3.) Remove the battery compartment cover.
4.) Remove the 4 screws with a TORX Plus 6 star screwdriver in the order shown. Please note that the screws are of different lengths.
Reassemble in reverse order as follows: screw in short screws with a 17 Ncm torque screwdriver and long screws with a 25 Ncm torque screwdriver, as shown in the picture. Always use new screws.
5.) Carefully remove the back of the case as shown in the picture. Watch out for contact springs, they are sharp.
6.) Unfasten the antenna module starting from the left side.
7.) Remove the system connector using the charger plug. Make sure there is no glue left.
8.) Pry up the vibration motor with a flat screwdriver. Make sure there is no glue left.
9.) Remove the microphone. A removed microphone cannot be reused.
10.) Unfasten and remove the SIM card holder.
11.) Pull up on the bezel. Be careful with the foil components of the loop.
13.) Unfasten the second ribbon cable connector and remove the system module.
14.) Carefully peel off the bottom ribbon cable.
15.) Slide the slider down before continuing.
16.) Slowly peel off the back plate.
17.) The removed back plate cannot be reused.
18.) Remove the 4 screws with a TORX Plus 4 star screwdriver in the order shown.
Reassemble in reverse order using a 17 Ncm torque screwdriver. Always use new screws.
19.) Remove the protective glass from the display.
20.) Stick the protective film on the inside of the display glass and on the LCD screen.
21.) Carefully pry and remove the camera module using the SRT-6 tool.
22.) Remove the speaker with tweezers.
23.) Pull up the camera body.
24.) Pry and remove the keyboard using the SRT-6 tool.
26.) Peel off the board-to-board cable.
27.) Detach the springs from the pin in the middle.
28.) Remove the hinges at the ends of the springs from the pins.
29.) The springs must be secured correctly. Attach the bottom spring first.
30.) Now secure the upper spring.
31.) Check if the springs are functioning properly.
If you liked it, please do not be lazy to click "I like" or "share" or "+1" just below, or post a link to the article in your blog or forum. Thank you 🙂
VIDEO
In this DIY Nokia 8800 Arte disassembly video, step-by-step instructions are presented in detail, thanks to which you can repair the phone yourself. With this video, you can repair your cell phone, display and touch screen yourself. Also, following the video analysis of the phone, you can replace the speakers and microphone with your own hands. In addition, the video instructions give recommendations on how to repair the battery and fix the phone's cable.
Fast delivery of inexpensive original spare parts for the Nokia 8800 Arte cell phone in Moscow and other regions of Russia by phone - 8 (495) 125 29 79.
Disassembly of the Nokia 8800 phone.
Important! Everything that you do - do it at your own expense. Remember: After disassembling the device, you will void the manufacturer's warranty.
1.) You will need the following tools: TX 6 Plus, TX 6 Plus Bit, TX 4 Plus, TX 4 Plus Bit star screwdrivers, torque screwdriver, SRT-6 disassembly tool (or guitar pick), flat screwdriver, metal tweezers and charger plug.
2.) Always stick a protective film on the display glass.
3.) Remove the battery compartment cover.
4.) Remove the 4 screws with a TORX Plus 6 star screwdriver in the order shown. Please note that the screws are of different lengths.
Assemble in reverse order as follows: screw in short screws with a 17 Ncm torque screwdriver, and long screws with a 25 Ncm torque screwdriver, as shown in the picture. Always use new screws.
5.) Carefully remove the back of the case as shown in the picture. Watch out for contact springs, they are sharp.
6.) Unfasten the antenna module starting from the left side.
7.) Remove the system connector using the charger plug. Make sure there is no glue left.
8.) Pry up the vibration motor with a flat screwdriver. Make sure there is no glue left.
9.) Remove the microphone. A removed microphone cannot be reused.
10.) Unfasten and remove the SIM card holder.
11.) Pull up on the bezel. Be careful with the foil components of the loop.
13.) Unfasten the second ribbon cable connector and remove the system module.
14.) Carefully peel off the bottom ribbon cable.
15.) Slide the slider down before continuing.
16.) Slowly peel off the back plate.
17.) The removed back plate cannot be reused.
18.) Remove the 4 screws with a TORX Plus 4 star screwdriver in the order shown.
Assemble in reverse order using a 17 Ncm torque screwdriver. Always use new screws.
19.) Remove the protective glass from the display.
20.) Stick the protective film on the inside of the display glass and on the LCD screen.
21.) Carefully pry and remove the camera module using the SRT-6 tool.
22.) Remove the speaker with tweezers.
23.) Pull up the camera body.
24.) Pry and remove the keyboard using the SRT-6 tool.
25.) Carefully pry the board-to-board cable
26.) Peel off the board-to-board cable.
27.) Detach the springs from the pin in the middle.
28.) Remove the hinges at the ends of the springs from the pins.
ASSEMBLY TIPS
29.) The springs must be secured correctly. Attach the bottom spring first.
30.) Now secure the upper spring.
31.) Check if the springs are functioning properly.
Repair Nokia 8800 in a Nokia service center, is produced in stationary conditions by qualified service engineers. The phone is drawn up and a form is written out on which the alleged malfunctions of the phone and the wishes of the owner are described in detail (keyboard repair, nokia 8800 repair and housing replacementrepair nokia 8800 immediately in place. So, nokia 8800 cell repair when eliminating the causes of a quiet call, it takes 20 minutes, repairing the antenna unit 10 minutes, replacing the lower loop 15 minutes.
Short repair times are due to the fact that all the necessary spare parts are already in the warehouse of the service center. If, for some reason, the necessary spare part was not found, then it is delivered from our warehouse in Moscow immediately.
Attention. All prices for nokia 8800 cell repair constantly changing due to lower or higher prices for spare parts.To get the current price for repairing Nokia 8800, call 507-53-11 in Moscow.
Nokia Center will fix the cause of the breakdown and repair it. An urgent repair of the Nokia 8800 is always possible at the Nokia Center immediately on the spot. From practice, it can be established that 80% of all defective devices were repaired immediately on the day the phone was handed over to the service center. All repairs and used parts are warranted for three months.
Over time, any mobile device, be it a portable music player, landline phone, or 8800 cell phone, ceases to function properly. It becomes more difficult to use an old phone, since the numbers on the keypad are no longer visible due to abrasions, the nokia 8800 is quickly discharged, small scratches appear on the casing and glass of the display, the quiet 8800 speaker or does not work at all. And then the question arises: Where to take the phone for repair and how much will the repair work cost 8800?
Below, we will try to describe in more detail the common faults of the 8800 cell phone and the cost of their elimination, as well as the repair time.
I decided to describe all the known "hardware" problems of Nokia 8800.
So:
№2
No. 3 Glass opacity around the perimeter with a thickness of 1-5 mm. In summer, in hot weather, sweat from the cheek penetrates into the cracks between the glass and the case. It remains there, forming smudges along the perimeter. It is treated only by replacing the glass or the lid itself with the glass in the collection.
All of the following during operation:
No. 4 cover backlash: it is treated by removing the latches from the body (easily removable) and bending them perpendicularly downward for a closer contact with the body, and therefore the back cover with the body.
# 5 dents and potholes: the treatment is banal. We lay on a smooth flat surface, squeeze out with a hard flat object in the opposite direction (for example, pliers / pliers). (c) The main thing is not to overdo it and not make a belly on the back side. The flip cap is more difficult. There is no direct access. Alternatively, take a flat, smooth file, put the end in place of the dents and tap on top in the middle, holding the other end in your hand. Something like a swing, only at one end of the hand, and at the other, there is a dent. We knock in the middle. Helps a little.
Perhaps they will also help you with the chassis, as there should be spot welding or miniature welding. It is possible to repair the chassis using a rivet, that is, fixing the bracket to the chassis. But the rivet must be fairly flat for the chassis to function properly. You need to consult with the master. If you take it, then the quality and the main thing is reliability will be HIGHER than new.
No. 6 scratches on the display: polished with GOI paste, or with a more perfect tool: Displex white paste. Most likely made on the basis of diamond dust. Make sure that the polishing cloth is thin and does not absorb well. Otherwise, the whole tube will be absorbed into the fabric. Polishes perfectly. Polish for a long time 15-60 minutes. Depending on what quality you want to get at the end.Although it is designed for glass, it polishes the case itself quite well. But the highest quality, of course, is in jewelry or a watchmaker.
P.S:
They ask for 130-150 USD. for silver and up to $ 180 for black.
Summary: when buying a working but outwardly killed Nokia 8800, you can save from $ 100 to $ 200. and above by installing all the electronics in a completely new, original housing.
the image shows as if an old TV set without an antenna (multi-colored noise).
Disassemble and look for breaks on the loop.
the image shows as if an old TV set without an antenna (multi-colored noise).
if you cannot order - return the phone to the client, especially since he does not think to pay
There was only such a sirroko recently with such a problem! Look at the plume at the bottom under the screen, most likely water! cleaning and soldering in my case solved the problem!
Below - under the screen - the camera's graphics accelerator. There are complaints about the camera. Look carefully and clean the cable connector with isopropyl alcohol - he really doesn't like even a hint of dirt.
today I'll sort it out and call you.
This is a photo of what, Halley's comets?
This is a photo of what, Halley's comets?
At the fotik, the battery sat down, did not have time to put the normal settings. Here is a photo
apparently pictures on the display. only the unfortunate fact surfaced - “today I’ll sort it out and call you. “I always believed that first parsing, trying, reading, asking for advice from a colleague on the ace, the phone .. if a dead end, we will post here, IMHO.
I just didn’t want to disassemble it because it was an expensive device, I thought if they said that there was a train, I’ll give it to the client right away. Legs did not reach the microscope, then seeing off at my brother's, then birthday.
+7 499 917-08-18
Type of shell: slider Display: color TFT, 262.14 thousand colors Built-in memory: 64 MB Camera: 0.50 million pixels, 600 × 800 Maximum talk time: 3 h Maximum waiting time: 192 h Body colors: silver, black, gold
The keyboard of the device, frankly speaking, is far from the top of ergonomics. Most of the buttons have to be pressed with your fingernail, since the bottom row of buttons is very tight against the protruding metal base.
The body of the model is almost entirely made of metal (note: not of metal-plastic).The material used to make the case is real steel. Both the battery cover and the front panel are made of this material. Thus, Nokia 8800, like a medieval knight, is almost completely covered in armor.
The display of the device is also endowed with a distinctive feature: it supports 262 thousand color shades. It is worth noting that the Nokia 8800 is the first phone (not a smartphone) from the company that can boast of this feature. The matrix resolution is 208x208 pixels, which is the same as in the Nokia 6230i. However, in comparison with the latter, the display has become even more sensitive to the sun, the device can be used in clear weather without any problems and searching for suitable tilt angles in order to see at least something. The cost of replacing the display on a Nokia 8800 phone is not cheap.
The device also has a niche for a camera. When folded, the lens is protected from all kinds of damage, as well as dirt and dust. There is no separate button for activating the camera.
The main menu of the device is very similar to the menu in Nokia 6230i, both in content and design, which, however, is not surprising, since both phones operate on the 40th platform.
The maximum operating time of the device, which was declared by the manufacturer, is 3 hours. In standby mode, the mobile device can withstand up to 200 hours. In practice, however, the mobile device has to be charged daily. This state of affairs can be easily explained: the phone is endowed with great functionality, a rather "powerful" display for it, great communication capabilities and at the same time a Li-Ion battery with a capacity of 600 mAh. As compensation, the device comes with another battery and a device that charges the battery in isolation from the device itself.
Urgent repair of Nokia 8800 in Moscow with a 3 month warranty! You can also always check the availability of spare parts for your Nokia model by phone with our operator or make an online order through the form on the website. Nokia repair costs at our service center are significantly lower than those of competitors.
By contacting our service with a request to quickly repair your Nokia Lumia 730 dual sim smartphone, you will always receive high-quality and careful service with a guarantee. Repair of any models of Nokia phones is our job!
Today we will pull the phone book from the once legendary phone. )
We will need:
Or such an old, useless, blue box. )))
Well, the cable itself, separate or universal. Putting the constructor together, we attach the boxes to the computer. )
Launch BEST, select Connect - COM / UFS / JAF.
We select the box to which the phone is connected.
The phone will be detected. We merge PM, contacts are in it. )
Open Contant Extractor. On the Nokia tab, select PM, press GO. Select the merged file.
On the Manager tab, a list of contacts will appear. Right-click, select export.
And we save it in the required format. )))
Good day ladies and gentlemen.
So, contrary to belief, I fell into my hands 3310. Broken :)
Backlight - yes, images - no.
Well. Considering the primitive of the construction, we will understand.
It can be easily disassembled, the outer panels are latched, the inner socket is on 6 screws
This is how it all looks from the inside.
We take an eraser and clean the screen contacts.
Well, and if we are talking about old technology.
Glass is broken, some of the buttons are not pressed. Still would! Date of issue 02.2007)
We get to the little screen first.
Well, for Klava - I wash the contacts with alcohol, peeling off the backing.
Putting it back and checking -
The buttons are pressing, everything is fine :)
These are the good old devices.
Well, taking this opportunity, I hasten to congratulate comrade @gepka on his anniversary.As they say, happiness, health :)
To repair your Nokia 8800 phone, use the information provided by us. We have placed the data of 144 repair companies so that you will certainly find a suitable organization among the proposed options. In the service centers you will find a high quality of repairs, the speed of their implementation and the extremely attentive and sensitive attitude of the staff to your problem.
If you need to replace the display, volume buttons, battery or repair the motherboard, do not hesitate that these operations will be carried out by the specialists of the presented companies in a couple of hours. Having at hand a sufficient range of spare parts, the craftsmen promptly carry out any types of repairs that require replacement of faulty parts. Such repairs usually involve providing a guarantee not only for the work itself, but also for parts that were replaced along the way.
The professionalism of the repairmen, the use of high-quality components and special tools allows us to provide service centers with an excellent subsequent guarantee for their work.
Below you will be asked to select a problem in order to immediately reflect their prices for the elimination of this malfunction in the displayed information about companies. Of course, you can always find out the full list of services and prices of the company - for this, go to the organization tab by clicking on the name.
We will also be happy to assist you in choosing a center for repairing Nokia 8800 by calling the hotline 8-800-775-90-67 - our employees are ready to advise you on favorable prices and services located near you. To find such companies yourself, use the filter that you see below on the left.
Nokia phones are one of the most reliable, and often even the owners of modern smartphones do not want to part with their "old friend", using it as a backup option. And some simply do not want to change Nokia to a more modern phone, since they are completely satisfied with it.
But even with these gadgets, troubles happen. For example, the nokia asha 200 phone is a great usable model, but it happens to freeze. The cause may be shock, water ingress, memory overload, operating system failure.
It happens that there is no way to get into the phone repair service. Something you can do yourself. For example, clear memory by deleting unnecessary SMS and contacts. If your phone gets wet, try drying it by removing the back cover and removing the battery. It will take 1-2 days. If the phone does not work after that, it means that the contacts have oxidized. Try cleaning them with rubbing alcohol, acetone, or a special oxide remover. If this did not help, then alas ... This means that the liquid has thoroughly spoiled the microcircuits and you cannot do without replacing them. And it is better to do it in the service.
If you still want to try self-soldering microcircuits, wiring or a pad on the board, you will need a hair dryer to warm up the microcircuits, flux and rosin. You can only warm up those that are not filled with a compound - a special resin. But if you really need to, there are liquids for removing the compound. Now we act according to the following algorithm:
we warm up and remove the microcircuit;
we clean the remnants of the legs on the microcircuit and the board with a soldering iron;
we put the microcircuit on the stencil, making sure that the holes of the stencil coincide with the contacts of the microcircuit;
cover the holes with BGA paste;
heat the paste until the lead balls appear;
wait for cooling, then remove the stencil;
heat the microcircuit to the board with a hairdryer.
Replacing the glass is easy. It must be greased with soldering fat and heated with a hairdryer. Then clean the contacts on the board to zero with a soldering iron. After that, put a new glass and warm it up with a hairdryer.
Nokia software repair is a job for specialists. It is necessary to understand the firmware configuration: which files are responsible for which functions, as well as many other nuances.It is better for a beginner not to take on this and take the phone to the service, but such trifles as a crack in the glass are an excuse to train their skills.
The reasons for Nokia 8800 Arte phone breakdown can be very different. But most of the devices fail with consequences, which can be eliminated only with the help of qualified service technicians who repair the 8800 model of a Nokia mobile phone. Often, owners of Nokia 8800 phones contact service centers with a request to set up a mobile phone or turn on a device that is locked because the owner has forgotten the password. In this case, Nokia repair takes a small amount of time and does not require serious material costs.
In addition to these common problems for all mobile phones, Nokia 8800 cell phones can, like all other mobile devices, suffer in extreme situations. For example, if the phone accidentally ends up in the washing machine, falls into the bathtub, or accidentally falls under the wheel of a car. As for the typical problems that Nokia 8800 phones have, these include:
1) cracks on the screen (not too strong for this model) due to the fall of the device;
2) failure of the slider or loop;
3) sticking buttons (largely depends on the accuracy of the owner of the phone);
4) problems with software: not very high-quality firmware sometimes leads to "freezing" or braking of the device.
Repairs to the 8800 model of a Nokia phone, in services that care about their image, are inexpensive, even when you need to tinker with the phone (for example, you need to replace a cable or a slider). It's a little easier to replace the display, the easiest and cheapest is to change the keyboard. Re-flashing the device is also possible, but all previously saved data is not saved in the mobile phone, this must be taken into account when handing over the phone for repair, and transfer all information to other media in advance.
Does your nokia need service? The reasons here are simple and understandable, usually it is the ingress of water on the body and parts, mechanical damage and, of course, falls. By the way, more about falls. This is the most common reason why nokia 8800 has to be repaired, since this particular model has a lot of weight, as a result of which the nature of the malfunctions after an impact is much more serious, and the consequences are more severe than in other models with a lower mass. The most common breakdowns after that are a cracked or broken display, glass, and a damaged case.
Despite the fact that the repair of this model is one of the most demanded, this does not affect its cost in the direction of rising prices. The sums for work with such devices differ little from the average prices for the same work with other models. In addition, Nokia is a very reliable device, and frequent customer requests to the workshop to repair the device are associated with the operating conditions of the phone and the user's personal appeal.
Replacing the body of the Nokia 8800 is exactly why the owner of the phone often has to turn to specialists, since many people buy this model as a fashionable device for a business person, and the scuffs do not suit this image very well.
As for the financial issue, let's add a little more: the prices for repairs of this model are constantly changing and almost always decrease as a result of falling prices for spare parts. By the way, we recommend purchasing original parts and discussing this point with the master, because often Chinese spare parts do not differ much from the manufacturer's parts in terms of cost, however, the quality and service life of "Asian souvenirs" leaves much to be desired.
Also, we consider it our duty to warn you that not in all service centers professionals can handle the repair of the nokia 8800, despite the fact that they work with nokia devices almost everywhere. The fact is that the nokia 8800 belongs to premium-class phones, and not every workshop will undertake such devices, so we advise you to contact large organizations.
Usually, in a situation with the nokia 8800 keyboard that has ceased to function, the clogging of this part with dust and dirt is to blame. If your hands are nimble, then it will not be difficult for you to clean the device yourself.
For such a repair of the nokia 8800, you will need a small amount of available tools: a napkin, double-sided tape, an ESD brush, a plate (or a plastic card cut off at the edges), a soft cloth, an eraser with abrasive elements, T4 and T5 screwdrivers.
First of all, unscrew all four bolts located under the battery cover: at the connector, gently pry the case up to the power button. If you have a Nokia 8800 arte in front of you, then remove the antenna by first unscrewing the bolt in the antenna compartment. After that, disconnect the ribbon cable from the board, remove the board and the lower glass. Slide the slider apart, peel off the back cover, unscrew two screws at the top and bottom using a T4 screwdriver. Remove the keyboard cover, but do not touch the display for any reason. Remove the backing and gently clean the copper pads with an eraser. Also, use the ESD brush to clean the board without touching the microphone.
Video (click to play).
After that, assemble the phone in reverse order, fix the decorative cover with tape. If you cannot assemble the device again, immediately contact the master.
