Do-it-yourself Samsung washing machine tank repair

In detail: do-it-yourself repair of the tank of a Samsung washing machine from a real master for the site my.housecope.com.

Owners of home appliances of a well-known South Korean brand will be interested in how a Samsung washing machine is repaired with their own hands.

Unfortunately, sometimes it is necessary to eliminate breakdowns and leaks of washing machines, even in an expensive price segment, and knowledge of error codes and related malfunctions may also be required.

First, you should familiarize yourself a little with the main features of these machines. First, it is stylish design.

Secondly, it is the original design of the drum. Modern modifications of Samsung washing machines are equipped with a fundamentally new technical solution - Drum Diamond Drum .

It belongs to an innovative type of honeycomb drums with a surface covered with many convex pyramids and small water holes, into which the fabric is not drawn.

Thanks to this design, a gentle wash cycle is provided. These drums can be very spacious - with a load of up to 12 kg of laundry, depending on the model of the machine.

Thirdly, worthy of attention heaters with double ceramic coatingnot covered with limescale, and inverter motorattached directly to the drum in some modifications.

Also interesting are the functions Fuzzy Logic and Smart Check responsible for the correct calculation of the washing mode depending on the amount of loaded laundry, as well as for diagnosing various machine malfunctions.

The number of wash programs depends on the model of the washing machine. Even the simplest modifications are equipped with all the necessary set of programs, and the new models have a washing mode called ECO Bubble - with the help of air bubbles, laundry is easier to wash even in cold water.

Video (click to play).

If the machine is marked with Wf, it means that this model is front-loaded, and if its name contains the abbreviation WD, it means that the machine is equipped with a built-in dryer.

But Samsung brand machines also have one small drawback - their instability to voltage drops in the network, which is important in our Russian reality.

When the voltage becomes either too high or low, then a control system called Volt Control simply turns off the washing mode to resume it immediately after the mains voltage has stabilized. This is not always convenient, so it is better to connect the washing machine through a voltage regulator.

After a short acquaintance with the parameters of this brand, let's move on to considering the main breakdowns.

To understand the malfunction that has arisen, you need to consider the most common of them and the reasons for their occurrence.

Here is a list of common problems:

Further, the methods of repairing them with your own hands will be considered, because it is not always possible to call the master. And for this you need to have a set of necessary tools.

Before starting repairs, you need to make sure that all the tools from this list are available:

flat and Phillips screwdrivers or screwdriver;
set of wrenches;
pliers, pliers, wire cutters;
tweezers - elongated and curved;
powerful flashlight;
long-handled mirror;
soldering iron;
gas-burner;
small hammer;
knife.

In addition to the listed tools, you may need a magnet to pull out small metal objects inside the machine, a long metal ruler to align the drum, a multimeter or voltage indicator.

But that's not all. In addition to the required set of instruments, the following building materials will need to be purchased for repairs:

sealant;
Super glue;
insulating resin;
soldering materials - rosin, flux, etc .;
wires;
clamps;
current fuses;
rust remover;
electrical tape and scotch tape.

Sometimes a multimeter is not needed, it is enough to turn on the machine and select a mode with a high water temperature. From the operation of an apartment electricity meter, it is easy to understand whether the heating element is receiving power.

If you are a beginner, then you can advise using a camera to shoot video or to photograph the workflow, so as not to confuse the sequence of actions and then correctly assemble the machine.

There are several important rules to remember that must be followed before starting repair work:

it is necessary to drain all the water from the machine;
before disassembly, be sure to (!) disconnect the device from the power supply;
choose a bright and spacious enough place for renovation.

If the unit cannot be moved to a convenient location, then ensure maximum illumination of the workplace.

The first step is to remove the top panel of the washing machine.

The second step is to take out the container for powders, this is not difficult to do. Next, you need to remove the cuff from the hatch. Caution is needed here. Use a screwdriver to pry the retaining clip, remove it, and then remove the O-ring. This should be done carefully, trying not to tear the soft rubber.

It was the turn of the control panel. In order to remove it, you need to unscrew two screws on the front of the panel and one on the right.

Next, you can proceed to dismantle the lower front panel. Pulling the latch lever, we separate the basement part of the facade - access to the drain filter and the hose for the emergency filter is open. The front panel can now be removed by unscrewing the eight fixing screws. The heating element and the drain pump open.

If during the repair process it is necessary to remove the tank and drum, then we advise you not to do this alone. Be sure to involve an assistant in this matter. Before removing the tank, you need to de-energize the heating element, disconnect all pipes, as well as the electrical wiring from the motor.

To do this, put the machine on its side, then remove the 4 screws on the bottom cover. The engine opens with a counterweight secured by shock absorbers. Disconnect the wiring from the connectors. Here it is important to remember what is attached to what, therefore, before disassembling, it is advisable to photograph everything, in order to then repeat everything exactly as in the picture.

But it remains to disconnect the drive belt from the engine. To do this, simply remove the belt from the pulley. Remember to put the drive belt on the small drive pulley first, then slide it over the large driven pulley and align to the center of the pulley when putting on the belt.

We present to you a diagram of the device, which will be very useful for repairs. The technical content of machines of different brands is about the same, and if you have already come across the replacement of spare parts for a washing machine, then it will be easier for you to cope with the next repair.

Now you can start a story about certain types of breakdowns and how to repair them.

The most common cause is insufficient water pressure. Then the machine stops, and in order to start it again, it must be turned off and then turned on again. If there is a lot of laundry loaded, for the machine to start, just turn it off and remove the excess.

If there is a break in the power cord or initially poor contact in the power button, then the device periodically turns off by itself. The machine may also stop if it is not level and slightly skewed.

To solve this problem, first check the water pressure in the water supply system, and also make sure that the valve supplying water to the machine is open well.

You should be aware that the free end of the drain hose connected from below must be located at a height of more than 2/3 of the height of the device, otherwise water will immediately pour out of the machine.

There are many reasons for this problem.Sometimes it is enough just to clean the powder container well - due to its clogging, water can simply flow out of it.

If, after checking these hoses, you are convinced that everything is in order with them, then the reason lies in the O-ring.

It is necessary to check the tightness of the seals, both in the door and in the connection of the filling hose. If they are worn out, they should be replaced. Then you need to check the drain pump and hose for foreign objects stuck there.

Therefore, the wash water does not heat up. This is due to the failure of the heating element, but do not rush to change it - this may also be damage to the wiring.

Therefore, you should carefully check the entire electrical circuit, as well as the contacts of the heating element itself, using a multimeter. If the tester shows the presence of voltage in the entire circuit, then this means that the heating element will still have to be replaced.

The place where the heater is installed should be thoroughly cleaned, only after that it will be possible to mount a new heating element.

The most common cause of noise is incorrect installation of the machine. Because of this, the unit produces a strong hum during spinning. For this, the position of the machine must be leveled using a spirit level.

But sometimes excessive noise can occur due to heavy wear on the bearings. It is impossible to fix them - only to change them. For an inexperienced repairman, this is a rather difficult task, because it may be necessary to saw and then glue the non-separable tank, behind which the bearing is located. Therefore, if you are not sure of your skill, then do not take up this business, it is better to call a qualified specialist.

But if the tank of your car can be disassembled, then this task can be within your power. To do this, you need to remove the tank, then disassemble it by unscrewing the bolts and disconnecting the fastening latches.

After the unusable bearing has already been removed, you should thoroughly clean the shaft, check if it is worn out, and then just install a new bearing.

Finally, we present a short list of error codes that are most often issued by the unit.

E1 - system error when filling with water. Means that the required water level during filling is not reached within 20 minutes. Eliminated by turning off and then turning on the machine.

E2 - error when draining. Most often occurs when the drain filter is clogged.

E3 - too much water. You do not need to do anything, the water is automatically drained within 2 minutes.

E4 - too many things. Their mass does not correspond to the parameters of the machine. You need to extract the excess.

E5 - water heating does not work.

E6 - malfunction of the heating element.

E7 - malfunction of the water level sensor in the tank.

E8 - water heating does not match the selected wash program. Most often due to problems with the heating element.

E9 - water leakage or drain, recorded more than 4 times.

DE, DOOR - bad blocking. Most often - a badly closed hatch door.

We bring to your attention a good video that you need to watch before you start replacing the bearing yourself.

The process of dismantling and replacing bearings:

What the disassembly process looks like:

Before starting self-repair, you always need to correctly assess your own strength and not take on overwhelming work. But repairing a washing machine yourself is not very difficult, it is enough to understand a little about mechanics, electrical engineering, and also have the necessary tools and materials at hand. You will succeed!

Any washing machine breaks down over time. Units of the South Korean manufacturer Samsung are no exception. Replacement of some parts requires almost complete disassembly of the device. In this article, we will talk about how to disassemble a Samsung washing machine with your own hands.

Disassembling the washing unit is not as difficult as it seems at first glance, but first you need to properly prepare for the upcoming repair. This requires:

determine the place for the work;
prepare a tool and related materials;
prepare the washing machine for disassembly.

The room for renovation should be spacious and well-lit; a free area of the floor with an area of 2 x 2 m will be required. It is recommended to cover its surface with newspapers or rags in advance so as not to get dirty during the renovation process.

Next, it is worth stocking up on the necessary equipment. For disassembling and repairing the washing machine, you will need:

screwdriver (with a set of bits) or a set of Phillips screwdrivers;
wrench;
flat screwdriver;
wrenches and hex keys (8 mm);
pliers;
pliers;
multimeter;
hammer;
a set of colored markers;
WD-40 grease;
silicone sealant;
CV joint grease;
clean rag.

If you have to saw the tank, you will additionally need: a hacksaw with fine teeth, a drill, a long drill, a gun with a sealant, screws or bolts.

Remember that after repair and replacement of parts, the unit will need to be assembled back, so immediately record all the stages of dismantling, using a photo or video, or at least write down the sequence of your actions. Then the installation process will take place quickly and without complications.

If your washing machine is still under warranty, it is best to contact a service center for help with troubleshooting. If you replace parts yourself, you may subsequently be denied free warranty repairs.

It remains to prepare the washing machine itself for further disassembly. Follow these steps:

de-energize the unit;
disconnect the inlet and drain hoses from the water supply and sewerage system, respectively;
take out the drain filter and drain the remaining water (at the same time the filter can be cleaned);
move the washing machine to the work area.

It should be borne in mind that to carry out work on disassembly and subsequent repair of a Samsung washing machine (for example, such models as s821, wf-s861, s803j and wf6458n7w) you will need several hours. In addition, if it is necessary to remove the tank from the unit, outside help will not hurt.

Before proceeding with the disassembly of household appliances, it will not be superfluous to familiarize yourself with its device. A general diagram of a Samsung washing machine will give you an idea of the structure of the unit, the location of its main parts and will help you with repairs.

The electrical diagram will be useful in checking the integrity of the wiring and the operability of some components.

Take a little time, sort out the diagrams and only then proceed directly to disassembly.

When the place for repair, inventory and washing machine are prepared, you can start working.

The first step is to remove the top panel of the machine. On the rear side of the unit, in the upper corners, there are two self-tapping screws on which the panel is attached. Unscrew them with a screwdriver (or screwdriver), lift the back of the cover, slide it towards you and remove the panel.

Then it is necessary dismantle the detergent drawer... To do this, press on the locking latch and pull out the container in the same way as you do for cleaning. Behind the powder tray are fasteners that hold the control panel; removing the tray, you can easily unscrew the bolts and detach the latches that secure it (usually one mount is located under the tray and two more on the back of the panel). Carefully detach the control panelso as not to damage the wires leading from it to the inside of the mechanism. So that the part does not interfere with further work, it is suspended from the right side of the unit using a special hook or simply placed neatly on the top of the machine.

When disassembling the washing machine, carefully inspect all parts for damage. For example, quite often the water level sensor fails. Access to the part is easy if you remove the top cover of the unit: the sensor is located, as a rule, on the side wall of the machine, closer to the top, and is attached with 1-2 bolts.Unscrew the fasteners, disconnect the hose and contacts from the pressure switch (the hose is held with a clamp, which must be unscrewed or spread with pliers) and inspect them. If necessary, clean the contacts and remove blockages in the tube, and check the sensor itself with a multimeter.

Further follows remove the hatch cuff... Using a flat screwdriver, gently pry up on the rubber collar clamp (retaining ring) with a flat screwdriver, gently pull on it, and then use the screwdriver to work around the entire circle to disengage the ring. Remove the rubber collar and place it in the drum. Proceed as carefully as possible so as not to damage the integrity of the rubber. Close the drum door securely.

Then proceed to dismantling the bottom panel... In Samsung washing machines, it is fixed with latches that must be detached from the case. On newer models, the panel is secured with screws; they are easy to find and unscrew.

It's time to dismantle the front wall. How remove the front panel washing machine Samsung? It is quite simple to do this: you should unscrew the self-tapping screws that attach the front panel to the car body (they are located in the upper and lower corners, under the dashboard and above the lower panels). Next, you need to remove the front wall together with the loading door from the hooks / latches. Disconnect the wires of the interlock beforehand.

Remove the back panel even easier: unscrew the four screws and remove the part. At once disconnect all hoses, which are attached to the tank of the machine: filler, drain, as well as from a pressure switch and a tray with powder.

Now follows disconnect the heating element wires and the temperature sensor or, if necessary, completely remove the tubular heater (for replacement). It is usually located at the front bottom of the tank under the drum. Unscrew the nuts and pull the heating element out of the socket. At this stage, you also need disconnect the motor wires and wiring. Be sure to take a photo of the location of the pins in order to connect them correctly during assembly. The terminals can be marked with colored markers.

To get to the tank, you have to remove counterweights (balancing stones); they are located at the top and bottom of the washing machine. Unscrew the fixing bolts and carefully remove the weights (they are quite heavy). When performing this work, an electric wrench will come in handy, which will significantly speed up the process of removing fasteners.

In order to remove the washing machine tank, you need two pairs of hands. After removing the counterweights, disconnect the shock absorbers, and then, together with an assistant, carefully remove the tank from the springs and remove it from the unit. Then disconnect the motor from the tank, for which first remove the drive belt, then unscrew the engine fasteners. Finally, remove the pulley by twisting the bolt in the middle.

To replace the bearings on the drum, you need disassemble the tank... The task will become more complicated if it turns out that your washing machine has a non-separable (welded) tank. In this case, it will be necessary either to completely change the part (which is not cheap), or to saw it (the procedure can take several hours, moreover, it is quite painstaking work).

It is much easier to replace the bearing assembly in washing machines with a collapsible tub (for example, in the Samsung Diamond 6 kg model). The two tank halves are held together with tie bolts and latches that need to be disconnected. To dismantle the bearing assembly, you can use a special car puller or gently knock down the metal rings with a hammer and chisel. Then you should carefully clean the seat and install new bearings and an oil seal.

Not all breakdowns of the washing machine can be repaired by yourself. For a global repair, you will need professional help and special tools.

After replacing and repairing all elements of the device, reassemble the machine in the reverse order of dismantling. Notes, photographs and notes made with a colored marker will come in handy for you.

Now you know how to disassemble a Samsung washing machine.Follow our recommendations, do not forget about the instructions, check the diagrams and record your actions. We hope that our article will be useful to you. Happy renovation!

For more information, watch the video on how to disassemble a Samsung washing machine.

She graduated from the author's physics and mathematics lyceum and art school. Received a higher education in economics in the direction of "innovation management". Freelancer. She is married and travels actively. He is interested in Buddhist philosophy, is fond of transerfing and loves Mediterranean cuisine.Found a bug? Select the text with the mouse and click: Image - Do-it-yourself Samsung washing machine tank repair

The habit of using the washing machine “sparingly” can lead to an unpleasant odor in it. Washing at temperatures below 60 ℃ and short rinses allow fungi and bacteria from dirty clothes to remain on the interior surfaces and actively multiply.

If the first signs of gestation appear on your favorite things in the form of untidy pellets, you can get rid of them using a special machine - a shaver. It quickly and efficiently shaves off clumped fabric fibers and makes things look worthy.

Before removing various stains from clothes, you need to find out how safe the selected solvent is for the fabric itself. It is applied in a small amount on an inconspicuous area of the thing from the wrong side for 5-10 minutes. If the material retains its structure and color, you can move on to stains.

Threads made of gold and silver, which in the old days were used to embroider clothes, are called gimp. To obtain them, the metal wire was pulled for a long time with pliers to the state of the necessary fineness. Hence the expression "pull (breed) gimmick" - "engage in long monotonous work" or "delay the execution of the case."

There are special traps to fight moths. The pheromones of females are added to the sticky layer with which they are covered, attracting males. Sticking to the trap, they drop out of the reproduction process, which leads to a decrease in the moth population.

Fresh lemon is suitable not only for tea: clean the dirt from the surface of the acrylic bathtub by rubbing with half a cut citrus, or quickly wash the microwave by placing a container with water and lemon slices in it for 8-10 minutes at maximum power. The softened dirt will simply be wiped off with a sponge.

The easiest way to remove scale and carbon deposits from the soleplate is table salt. Place a thick layer of salt on the paper, heat the iron to maximum, and apply light pressure several times over the salt mat.

The dishwasher is not only good for dishes and cups. It can be loaded with plastic toys, glass shades of lamps and even dirty vegetables, such as potatoes, but only without the use of detergents.

Stretch ceilings made of PVC film are capable of withstanding from 70 to 120 liters of water per 1 m 2 of their area (depending on the size of the ceiling, the degree of its tension and the quality of the film). So you don't have to worry about leaks from the neighbors on top.

In order to repair a Samsung washing machine with your own hands, you must have knowledge in plumbing, electrical engineering and have the necessary tools at hand. Self-elimination of malfunctions does not cause great difficulties, but it allows you to significantly save your home budget. It is not known how much the repair costs, but, as a rule, the prices for its implementation are quite substantial.

Over time, especially with improper operation, any unit fails. The washing machine is no exception. Samsung devices have proven to be of high quality and reliable, but they also have weak points. As a result of the analysis, it turned out that the most frequent breakdowns are the following:

wear or tear on the drive belt;
failure of the heating element (heating element);
failure of the filler valve;
malfunction of the drain pump;
destruction of the drain pipe.

According to statistics, heating elements and drive belts most often fail.As a rule, this happens due to errors in operation.

In addition, you need to know that each detail has a certain life span. For example, brushes of an electric motor have a service life of 8-12 years, a bearing unit - 6-8 years. Of course, these terms can be extended, but, unfortunately, not by much. So sooner or later, your washing machine will "ask for help."

To carry out a quality repair, you need to carefully prepare for it. This means that in addition to the tool, it is necessary to find a place where the machine will be repaired. It should be large enough and well lit. A garage is best suited for these purposes. For more detailed information about the device and car repair, you must definitely watch a video on this topic.

Before repairing, it is imperative to prepare a tester, a soldering iron, grease (for example, Litol-24), WD-40 liquid, solvent, rags and a camera. Filmed disassembly processes will be of great help during assembly.

It is better to repair the car together with an assistant.

In case of such a malfunction, first of all, it is necessary to remove the front wall. This must be done carefully so as not to damage other parts.

Special attention should be paid to on rubber seal loading door and all kinds of plastic latches so as not to accidentally damage them during repairs. To remove the front wall, you need to disconnect the lower bar, dismantle the top cover with the control panel. During operation, you will have to disconnect the wires from the electronic elements, so it is necessary to take measures so as not to confuse them during assembly. Now you can carefully detach the front wall and set it aside.

Next, we begin to work directly with the heating element.

All operations are so simple that a service center is simply not needed in this case. We disconnect the wires from it and measure the resistance. If it is more than the norm or is absent altogether, then you will have to remove the heating element. To do this, you need to unscrew its mount. It is between the contacts. Then we carefully take out the heating element itself and examine it. If there is scale on it, then it must be replaced. Given the specificity of the part, it must be remembered that it not being repaired... The heating element only needs to be replaced with a new one.

Important. Before replacing, carefully examine the marking of the heating element, if it differs from the old one, it is not recommended to put such a heater in the car.

It is very easy to repair this breakdown. To work with the belt, the rear wall of the machine is detached. It's easy to get to him. The only thing that can complicate the job is the counterbalance. If so, then you need to pull it back a little. Before removing the belt, you need to carefully examine it. If such defects as tears, cracks and abrasions are found, the belt must be unconditionally replaced. The old drive belt can be easily removed. To do this, do the following:

We take one thread of the belt in our hand.
We pull it towards ourselves with little effort.
Insert the screwdriver into the groove of the pulley under the belt.
We turn the pulley until the belt comes off it.

The new belt is installed in the reverse order. As you put it back in place, remember your experience with putting on a sleeping bike chain. For ease of use, it is first put on the engine pulley. When replacing the belt, you must also pay attention to its markings. It is impossible to install a non-original belt.

Important. Rubber dust on the bottom of the machine indicates belt wear.

Rather good maintenance rather than repair solves all the problems with these nodes. The main reason for their failure is clogging... Therefore, all repairs are reduced to cleaning them. The most acceptable access to them is through the bottom of the car. It can be easily removed. The process of cleaning them is as follows:

Remove the clamps securing the branch pipe.

Remove the drain hose.

Remove the pump carefully.

Remove the pipe.

Wash the removed parts with hot water jet. After assembly, the machine should work.If this does not happen, you need to remove the pump again and take it to a service center. Repair the pump yourself Not recommended, in view of the need for its precise adjustment after repair. When inspecting the branch pipe and if damage is found on it, there is only one way out - replacement.Important. Damage usually occurs at the points of attachment with clamps.A broken valve is not inherently a malfunction. Repair is reduced to replacing rubber seals. In order to gain access to the valve, it is necessary to remove the top cover of the machine. It remains to carefully get it out and replace all the rubber gaskets. If there are integral seals on the valve, then its life is unlimited.We have considered simple types of repairs. More complex, for example, replacing the bearing assembly of the drum of a washing machine, it is better to entrust the service technicians.As you can see, repairing and maintaining a Samsung washing machine with your own hands is not such a difficult business. Of course, there are also more complex types of repair, where you cannot do without a washing machine repairman. For example, when electronics fail. But such troubles are rare.

In 21% of cases, the reason for the failure of the CMA is the wear of the drive belt. The wash may stop in the middle of the cycle and the drum will not rotate. Only replace the belt with an original part.

12% of breakdowns are taken over by the inlet valves. As a result of rubber wear or drying out, water spontaneously pours into the tank. Also, the valve can become clogged, and then the water does not enter the machine well.

The remaining places are divided among themselves by parts: a drain pump, worn out oil seals and bearings.
Poor drainage is caused by a blockage in the drain system. Constant self-draining of water occurs due to incorrect connection. Depressurization of the elements leads to leaks in the Samsung washing machine.

By displaying the fault codes on the display, the system informs the user about the problem that has arisen. You need to understand the meaning of the Samsung washing machine error codes and start repairing yourself.

Consider how to repair a Samsung washing machine with your own hands.

It is necessary to check the drain system: most often the reason is a clogged drain pipe or pump.

Unplug the machine, turn off the water.
Disconnect all communications.
Remove the dispensing tray by pressing the release in the center.
Open the drain filter hatch on the bottom of the front panel.
Drain off any remaining water and clean the filter.
Lay the CM on its side, open access to the bottom.
Having found the location of the pump and the pipe, loosen the pipe clamps.
Disconnect the pump wires.
Remove the screws securing the pump.
After removing the pump, check it for clogging.
Remove the branch pipe and flush it from dirt.

Inspect the nipple carefully for damage. Most often, it loses its tightness at the clamp attachment points. In the event of a malfunction of the branch pipe or pump, new elements must be installed.

To check and replace, you need to get to the heating element. By the way the Samsung washing machine is arranged, we conclude: in order to get the heating element, you need to remove the front case of the washing machine.

We repair the washing machine ourselves:

After disconnecting the CM from the mains, unscrew the screws securing the top panel from the back.
Pull out the dispensing tray. Unscrew the bolts behind it.
Unscrew the rest of the bolts and remove the control panel of the Samsung washing machine.
Remove the bottom panel.
Bending back the hatch cuff, pry up the metal clamp and remove it.
Place the cuff inside the drum.
After unscrewing the door locking screws, as well as disconnecting the wires, remove the front panel.
There is a heating element at the base of the drum.
Disconnect the heater wires.
Unscrew the center nut (not completely).
After pushing the central bolt inward, remove the heating element.
Remove the thermostat from the heater.

If the thermostat is working properly, simply move it to the new heating element. Installation is carried out in the reverse order, after which the body is placed.

The reason for the lack of water may be a blockage. When repairing a washing machine with your own hands, first of all:

Twist the shut-off valve.
See if there is sufficient water pressure at the tap.
Inspect the inlet hose. Maybe he bent over, twisted.
Disconnect the hose and rinse under pressure from the tap.
Take out the filter mesh of the inlet valve.
Clear it from the blockage.

If, however, an excessive amount of water enters the machine, the filler valve must be checked.

After removing the top panel of the CM, you will see an inlet valve on top of the wall.
Disconnect the valve wires.
Unscrew the fixing bolts.
Loosen the clamps and disconnect the hoses.

If the overall valve is intact, replace the rubber seals. If not, install a new part.

To replace the belt, you need to know how to remove the back wall of the Samsung washing machine:

After unscrewing the bolts, remove the back panel.
Remove the old belt from the pulley.
If inspection confirms belt wear, install a new element.
Start sliding the belt over the engine pulley by moving and rotating the drum pulley.

Now you know how to fix a washing machine without calling the master.

When washing, did the CM begin to vibrate strongly, buzz, make noise? Check the correctness of the installation, how stable the equipment is on the floor.

A more serious cause of noise is bearing wear. To replace it, you need to know the device or have a diagram of the Samsung washing machine.The change of bearings is described in detail in the video:

The reason may be in the control panel. It is necessary to check the contacts of all buttons, perhaps they are stuck, or the keys themselves are pressed.

Another problem lies in the electronic board. Repairing a control module in a Samsung washing machine is not an easy task, so it is better to contact a service center. Of course, before contacting you can inspect the board yourself:

After removing the top cover, pull out the detergent drawer.
Remove the screws holding the control panel.
Release the plastic clips and disconnect the wires.
Having released the latches of the block, remove the cover and take out the board.