Do-it-yourself petrol brush repair Sparta 25

Modern technologies and equipment make it possible to produce the best and optimal technical solutions that become effective assistants in the arrangement of a summer cottage or a personal plot. The green lawn and other plantings can grow rapidly, a petrol cutter is used to tidy up the local area and mow the lawns, which is also called a brushcutter or trimmer, a petrol mower.

Traditional braids are inconvenient and unsafe to use, require a significant investment of time and effort, which will help save gas mowers, combining functionality and practicality in their design. In the photo of the petrol brush, you can see various high-tech devices, which are inherent in a set of operational characteristics, including such parameters as increased productivity and a long service life.

A convenient and reliable trimmer is a technical device consisting of individual mechanisms, parts and elements that can wear out, become unusable and damaged during intensive use.

Even with regular technical inspection, maintenance procedures and careful storage, such devices and their individual parts require repair and even replacement, all repair procedures can be performed independently.

Brief content of the article:

The easiest way is to give the petrol cutter for repairs, having allocated a certain amount of funds from the family budget, prompt and high-quality repair with your own hands is no less simple and convenient if you want to understand the design of the petrol cutter and fix all the problems.

The mass and piece production of trimmers is based on the use of generally accepted technology, a typical design scheme consists of certain elements and parts, it is important to know them when carrying out independent repair work:

• top part. The basis of the entire structure, where all the important elements are collected, such as a starter, a carburetor and a petrol cutter engine;
• middle part. A hollow rod, inside it is a cable that connects the motor and the gearbox, which drives the cutting line. In this part, there are fasteners for distributing the weight of the entire structure and a belt for fixing the trimmer on the belt of a person using the trimmer for its intended purpose;
• Bottom part. It houses the gearbox and cutting elements, which are hidden under a practical cover to protect the user. The casing provides an increased level of safety, preventing large fractions of debris, stones and glass from entering a person while working with a petrol cutter.

Knowing exactly the internal structure and the principle of operation of the trimmer, you can independently carry out repair measures for the structure or replace individual components that have become unusable, using the repair instructions.

The most common and common failures of the unit that need to be corrected on their own include the following problems:

• engine malfunction, due to which the brushcutter does not start and does not work;
• increased vibration of the brushcutter bar, which complicates its intended use;
• increased overheating of the gearbox, its accelerated heating during operation;
• slow and weak functioning of the cutting line at insufficient speed;
• clogging of the starter grille, causing overheating of the engine and its refusal to work;
• fast and frequent clogging of the carburetor due to the use of low-quality fuel;
• clogging of the air filter due to non-observance of the measures for the care of the device.

All these problems can lead to the fact that the device will lose its working capacity. Before ordering the necessary spare parts for the mowing, a visual inspection and diagnostics of the device should be carried out.

Particular attention should be paid to individual spare parts and units of the device, to check them you do not have to contact a professional master, a set of diagnostic measures will help you to identify the consequence of a loss of performance with your own hands.

If the trimmer motor does not start or stalls immediately after starting, when the gearbox overheats or during the operation of the device, extraneous noises are heard and vibration is clearly felt, it is important to visually inspect and identify a non-working unit.

To optimize the preparatory measures before repairs, you should carry out a simple diagnosis and check step by step:

• the presence of fuel in the tank and lubrication in the main units;
• serviceability of the spark plug and its performance;
• the cleanliness of the fuel and air filter of the brushcutter;
• clogging of the outlet channel and breather of the device;
• the quality of the fuels and lubricants used.

To determine the functional efficiency of the petrol-cutter's ignition, it is necessary to determine whether the spark plug is working by testing the appearance of a spark when it comes into contact with the body of the functional device.

The spark plug itself can be replaced with a new one, having previously dried the candle channel, if necessary, the old element is also dried, cleaned with special devices and returned to its place.

In the process of inspecting the carburetor, it is worth paying attention to the possible leakage of the fuel used; to identify problems with the carburetor, the following measures must be taken:

• purging the fuel hose to eliminate possible blockage of the element;
• checking and replacing the gasket between the engine and the carburetor;
• determination of tightness and maintenance of constant pressure in the unit.

If necessary, you can personally disassemble and thoroughly clean the unit using gasoline, the jet and channels are cleaned using compressed air.

The gearbox transmits torque from the motor shaft to the cutting tool, its gears during operation must be absolutely clean and always lubricated with special grease.

• 

Carrying out a technical inspection on your own once a season will allow you to get rid of the need to repair the gearbox or replace it, with the purchase of an expensive new unit.

The starter is necessary to bring the trimmer into working condition, its diagnostics consists in checking the tension of the starter cord connected to the teeth of the starter coil, which are often destroyed during an abrupt start.

An inoperative starter in a petrol cutter cannot be repaired; it must be replaced with a working unit as part of a mandatory technical inspection or a set of repair measures.

Cutting elements require special attention and care, which must always be cleaned of dirt and cut grass after use. Regular inspection and thorough preparation of the device for operation will help to avoid costly and time-consuming repairs, and always be confident in the performance of the petrol brush.

Repair of petrol cutters Oleo Mac Sparta 25 Part 1 removing the carburetor Mp3

PERRUQUES SYNTHÉTIQUES DE BONNE QUALITÉ CUSTOMISER VOS PERRUQUES SYNTHÉTIQUES Mp3

Album Vintage Mickey Alternative 2014 Mp3

STRADEUS Paris Bass Boosted Mp3

Eskiya Dunyaya Hukumdar Mp3

Brezhnev The Whole Truth About Him Documentary Mp3

Super Juniot Otra Vez Mp3

DAMLA OZODBEK NAZARBEKOV JANANIM YANGI DUET 2018 Mp3

Legendary Official Audio Welshly Arms Mp3

Nice pictures of mangle and foxy Mp3

viburnum red song Mp3 download

Terror in Tokyo Echo of Terror Zankyou No Terror Anime Rap Mp3

Can T Stop The Feeling Trolls Justin Timberlake Anna Kendrick Mp3

lucky lucky lucky mi Mp3 download

bach mass in b minor Mp3 download

On our site you can listen and download music compositions in mp3 for free. Our search engine will find any song. Listen and download music in good quality. Don't forget to share the link with your friends!

VK group for the repair of garden equipment
I also recommend my video on the reasons for the sudden stop of the two-stroke engine of garden equipment (lawn mower, trimmer, chainsaw) at full throttle. On the example of a petrol cutter (trimmer) Oleo-mac Sparta 25 (Efco 25)

Spare parts for brushcutter Oleo Mac Motorcycle brush Oleo Mac sparta 250s carburetor repair

Tachometer for adjusting the carburetor

Brushcutter Oleo Mac 350 won't start after idle

Dismantling and flaw detection of the MZA-102 carburetor installed on low-power two-stroke engines with a volume of 30 to 50 cc / cu. Self-repair at home. We do everything ourselves with our own hands. We design and repair ourselves. Manufacturing of small agricultural tools for processing a vegetable garden. Repair of motorized equipment, chainsaws and petrol cutters. Self-repair of household electrical appliances. Easy and affordable repair of automotive and motor vehicles. To your attention New for the 2014 season - A device that turns your petrol trimmer into a motorcycle pump for pumping water. Do you want to know how this is possible? Watch this video and subscribe to our channel! Tel. Reference:

Self-adjustment of the carburetor gas cutters do it yourself is impossible without preliminary work, knowledge of the theory, understanding of the structure of the fuel system. Annotation for the repair of the carburetor.

Petrolcutters, like all petrol powered tools for the garden, are not difficult to maintain. It is possible and necessary to repair, configure without the help of others. For instance, carburetor adjustment petrol cutters with your own hands - a matter of 5 minutes.

The carburetor from the petrol cutter is a unit in the power system. In it, like all carburetors, there is a process of mixing air and fuel (gasoline) for the forthcoming supply to the engine cylinders.

In this process, the main thing is the correct proportion of fuel and air, which is why the carburetor is regulated.

Mesh filter. With this element, most often there are only two tasks:

In order to find out the cause of the breakdown, the fuel filter cap is unscrewed to remove the strainer. If dirt has simply accumulated on it, then flushing in gasoline or blowing will help.

If there is visible damage to the mesh filter, it is imperative to install a new one. There may also be damage to the fuel supply pipe (during repairs, they practice checking this element).

The carburetor starter almost always does not work due to blockages. Use acetone or the same gasoline for flushing.

Blowing out parts of a carburetor with a blockage with compressed air is an acceptable and comfortable repair practice.

The throttle body, the places where the carburetor parts are bundled, the inlet or outlet pipeline - all of these parts are subject to depressurization. You can probably check with a simple method - smear the problem area with soapy foam.

The base of the carburetor of the petrol cutters is a duralumin body. It houses a diffuser (hole with inner contours). Air is blown through this hole. The flow rate of oxygen (air) depends on the cross-section (orifice) of the diffuser.

The diffuser is equipped with fuel channels. From them, fuel is drawn in with the help of a stream of air.

Outside on carburetor establish:

• fuel pump;
• jet system;
• a system for adjusting the consistency of fuel with air;