DIY bosch maxx 4 repair

In detail: do-it-yourself bosch maxx 4 repair from a real master for the site my.housecope.com.

We continue the series of articles on the repair of Bosch washing machines.

How to start the service mode, troubleshoot basic faults in Bosch Maxx4.

Here are examples of washing machines of this model range: wfc 2060, wfc 2063, wfc 1663, wfc 2062, wfc 1600, wfc 1662, wfc 2065.
Their difference is in the control panels, the filling is about the same, so the repair and operating instructions are similar.

For diagnostics, you can run a service check of the nodes:

1.program control knob to “OFF” (0)

2. simultaneously press two buttons of additional functions

3.The program selector to the position of cotton 30 degrees, the LEDs work and the end of the program light up

4.Select the tested item with the selector clockwise:

- cotton wash 60 degrees (electric motor test)
- cotton wash 60 degrees economical (drain pump)
- cotton 90 degrees (water intake, maximum heating with a heating element)
- rinsing (valve check pre and main wash)
- spinning (main wash valve)
- drain (preliminary valve)

5. to start, press the "start" button

If a malfunction is detected, an error code is displayed.

Let's look at the combination of indicators:

1.Mistake of the hatch door lock

6.Water heating does not correspond to the program

7.Fault temperature sensor

To eliminate and replace faulty devices, look at the pictures.

Remove the top cover, take out the detergent drawer, and unscrew the fixing screws securing the control panel.

To remove the front panel, dismantle the lower decorative strip and unscrew the screws.

Today, washing machines are a common feature in apartments and private houses. Bosch washing machines are very popular, since they are made from high-quality materials using modern technologies. But even such cars can fail over time. This article will show you how to repair your Bosch washing machine with your own hands.

Modern Bosch washing machines contain a special program that allows you to identify faults without asking for help from a master.

The operating instructions for your Bosch washing machine should contain information on how to perform this diagnosis. If the drum has stopped rotating, then you must perform the following sequence of actions:

Video (click to play).

Close the door;
Set the program selection knob to the "Off" position;
Wait a couple of seconds;
The spin handle should be set to the “Spin” position;
Then wait until the "Start" button starts blinking;
Hold the "Spin RPM" button pressed;
Wait until the "Start" button flashes again;
Set the handle to the "Drain" mode;
Release the button "Spin revolutions";
Determine the last breakdown by the error code for the Bosch washing machine.

The program clears the last error from memory and runs diagnostics. To check the electric motor, set the mode selector knob to position 3.

To check the drain pump, set the knob to position 4. You can check the heating element by setting position 5. Diagnostics of the hot or cold water inlet valves is carried out by selecting positions 6 and 7. When position 8 is selected, the water inlet valve is tested during the main wash, and 9 - preliminary washing.

According to the technicians of Bosch service centers, the following breakdowns are most common:

Water does not heat up during washing;
Water does not drain;
The drum does not rotate;
The drum of the washing machine makes a noise;
Water is not collected;
The electric motor will not start.

When analyzing the malfunctions, one can come to the conclusion that in washing machines Bosch most often comes out of the standing heating element. If the heating element is broken and the electronic system is working properly, then the repair will not take much time.

However, if the electronic system is also out of order, then the repair will be quite expensive. After all, you will have to replace the electronic modules and call the master.

There are a number of reasons why a Bosch washing machine can fail. Let's consider them in turn.

She may not drain the water at the end of the wash cycle for one of the following reasons:

Clogged pump or drain filter;
Poor contact between power supply and pump;
Drain pump defective;
The water level sensor is broken.

The drum stoppage can occur for the following reasons:

The drive belt is worn out;
Malfunction of the control board or electronics;
Failure of the electric motor (rare case).

The drum may make noise during operation. This may be due to the following reasons:

Bearings came out of standing;
Small items are stuck in the drum;
The shock absorber has broken;
Counterweight problems.

It is possible that no water is drawn into the tank. In this case, the following reasons are distinguished:

Clogged Aquastop system or pump;
Lack of water in the plumbing;
Hall of the drain hose.

If the electric motor does not start, then, most likely, the door of the drum hatch is not closed or the electronics are out of order. After finding the cause of the malfunction, you can proceed with the repair.

The drain filter is located at the bottom of the machine, under a cover or panel. To clean the filter - open the cover. To do this, turn it counterclockwise. Filter - rinse and reinstall.

To clean or replace the drain pump, you must remove the front cover of your Bosch washing machine. This work is laborious, but not difficult.

Quite often, there is a malfunction in which water is not drawn into the Bosch washing machine. In this case, it is necessary to check the water supply and the water supply valve. They can be closed. Next, check if there are any kinks on the drain hose. If everything is in order, check the condition of Aquastop. If this element of the Bosch washing machine is out of order, it should be replaced with a new one.

If the water level sensor breaks down, it must be replaced. To do this, first dismantle the top cover by unscrewing the two self-tapping screws located at the back. This sensor should be located in the right corner under the cover. To pull out the water level sensor, you need to push down on the latch. Next, remove the hose and disconnect the contacts. Instead of the old sensor, a new one is mounted.

You can replace the heating element of your Bosch washing machine yourself. To do this, you need to remove the back cover of the Bosch washing machine. The heating element is located below, under the tank. To replace the heating element, proceed as follows:

Unscrew the bolt that secures the heating element to the tank.
Disconnect the wires;
Dismantle the heating element;
Install a new heating element and carry out all the steps in reverse order.

Replacing bearings on Bosch washing equipment is a rather difficult task, since for this you will need to disassemble almost the entire washing machine. Watch a video on how to replace bearings:

Stopping the motor can cause wear on the drive belt. You can replace this element yourself. To do this, you need to perform the following sequence of actions:

Open the back cover of the Bosch washing machine;
Remember how the belt is attached to the grooves of the pulley. Better to photograph this element.
Take the belt just below the pulley and gently pull it towards you.
With your free hand, turn the pulley counterclockwise.
Pull the old belt out of the washer body.
Put a new belt on the motor of the Bosch washing machine.
Tighten the belt with one hand and try to slide the drive belt onto the pulley with the other.
Turn the pulley counterclockwise without loosening the belt. In this case, you must try to put on the belt completely.
Install the housing cover of the Bosch washing machine.

Drum noise can be caused by worn shock absorbers, bearings, and torn off counterweight.

Before replacing the shock absorbers, you need to carefully examine the drum of the Bosch washing machine using a flashlight. There is probably a small object stuck in it, which makes a noise when the drum rotates. You can learn how to replace shock absorbers in a washing machine from the following video:

Loose counterweights, which are located at the bottom of the Bosch washing machine and under the top cover, can also cause noise. To eliminate this malfunction, you need to tighten the counterweight fasteners.

If it is not possible to fix the counterweight, then it is recommended to replace it with a similar one. This failure is quite rare.

There are two ways to fix this problem. The essence of the first method is that the electric motor of the Bosch washing machine must be removed and given to the craftsmen for repair. They may be able to fix the problem. If the engine cannot be repaired, then it will need to be replaced. Such a replacement will be quite expensive.

In order to get to the motor of the Bosch washing machine, you need to remove the back wall of the washing machine. The engine is located under the tank. First you need to disconnect the wires and the sensor from the motor. Secure the motor with three fasteners. They must be unscrewed. Experts advise to check the condition of the sensor condensate before removing the motor. For these purposes, you will need a multimeter. It is necessary to connect the probes of the device to the contacts and look at its indicators. The multimeter should read 20-50 ohms.

If you suspect that the wiring is faulty, you must check all terminals, contacts and plugs.

If the control unit fails, you need to call the wizard or dismantle the part and take it to the Bosch service center. You should not try to repair the electronics of German technology. After all, to do such work, you need to know many subtleties.

One of the most popular series of Bosch washing machines in recent years has become the MAKS-4 series, which includes front-loading machines with a cabinet depth of 40 cm. Unlike its full-size "sisters" - washing machines of the MAXX series with a cabinet depth of 60 cm and a load of 6 kg of linen, - machines of the MAKS-4 series are designed for a load of 4 kg of dry linen.

The machines of this series have an electronic control system Fuzzy Logic, with the help of which the imbalance of the laundry and the price formation in the drum are monitored, as well as the control of the water consumption and rinsing time in accordance with the load of the laundry.

The control panel of the MAKS-4 series washing machines is equipped with rotary knobs for selecting the washing program (preliminary, intensive, delicate, hand wash of wool, etc.), buttons for selecting additional functions "Easy to iron", "More water", "Quick wash "And LEDs indicating the progress of the program (from top to bottom:" readiness "," work "and" end of work "). In fig. 1 shows the control panel of the Bosch WFC 2060 BY washing machine (according to the company's new designation system - model B1WTV3002).

Rice. one Control panel of the Bosch WFC 2060 washing machine

On the control panel of this model there is also a knob for selecting the speed of rotation of the drum during spinning (from 600 to 1000 rpm).

Using the program selector knob, the mode is set according to the type of laundry and the degree of soiling. So, for cotton and strongly dyed colored fabrics, you can set the wash mode at 90 ° C without prewash or with a prewash at 60 ° C. For lightly soiled laundry or for fragile colored fabrics, you can select a wash cycle at a temperature between 30 and 60 ° C (the so-called EASY CARE mode or Pflegeleicht mode).

When you select the additional function "Easy to iron", the spinning of the laundry occurs at intervals, the duration of which is determined in accordance with the set washing program.

Thanks to this spin mode, the number of creases on the laundry is reduced, which makes it easier to iron.

Another model of this family - the Bosch WFC 1600 BY washing machine (according to the new designation system of the company - model B1WTV3800A) - does not have a knob for adjusting the drum rotation speed during spinning, instead there is an additional button for selecting the rotation speed - 800 or 600 rpm. Instead of the “Easy to iron” function, there is a “Forced spin off” function, also activated using a button.

This model of washing machine has energy efficiency class A, washing efficiency class A, spin efficiency class D. When washing colored laundry at a temperature of 60 ° C, water consumption is 49 liters, electricity consumption is 0.8 kWh, washing time is 90 minutes. ... The machines are equipped with the Aqua-Spar system, thanks to which the laundry is quickly and efficiently moistened.

In fig. 2 - 5 show the structural elements of the WFC 1600 BY washing machine (control panel, housing elements, tank, drum and main electrical components, hydraulic system), and in table. 1-4 lists the corresponding components.

Rice. 2 Structural elements of the WFC 1600 BY washing machine (control panel)

Household appliances from Bosch have earned the love of customers for their quality. German-assembled washing machines evoke admiration, ranging from the quality of the materials used for the production of machines and ending with their ergonomics. However, even among this technique, there are copies of machines that fail. That is why, we decided to write an article on how to repair Bosch washing machines on our own, and whether it is possible to do it.

Modern models of machines from Bosch are equipped with a special program that allows you to identify equipment malfunctions without contacting a master. The instruction manual will probably tell you how to make such a diagnosis correctly. If not, then we offer a detailed algorithm for testing machines, in the case when the drum has stopped rotating:

Close the drum door of the machine.
We put the program selection knob to the "Off" position.
We are waiting for 2-3 seconds.
Now we turn the knob to spin mode.
We are waiting until the "Start" button on the machine's control panel flashes.
Hold down the "Spin speed" button.
We are waiting until the "Start" button flashes again.
We turn the knob to the "Drain" mode.
Important! You need to rotate the handle clockwise.
We release the button "Spin revolutions".
By the error code of the Bosch machine, we determine the last malfunction.

For your information! If the washing machine diagnostics did not start at all, then there is a malfunction in the system board.

In addition, the program provides for deleting the last error from memory and starting diagnostics of faulty elements. To start the engine check, you need to set the mode selector knob to position 3. When the knob is set to position 4, the drain pump will be checked, and in position 5 - by the heating element. Positions 6 and 7 are provided for diagnostics of hot or cold water inlet valves, in position 8, testing of the water inlet valve will begin during the main wash, 9 - preliminary.

The masters of Bosch service centers found that of all possible breakdowns of washing machines, the following malfunctions are most often encountered in Bosch machines:

The water does not heat up during washing.
Water does not drain.
The drum does not rotate.
Noise inside the drum.
No water is drawn.
The engine will not start.

Based on this list, we can conclude that in washing machines of this company, the heating element most often burns out. If Teng burned out, and the electronic system remained intact, then the repair will be carried out quickly and safely.Otherwise, you will have to change expensive electronic modules, giving the technician to the master.

What malfunctions can occur in the washing machine, everything is clear. And what can cause a breakdown, you need to find out. Let's deal with everything in order.

If the machine does not drain the water after the wash cycle, this may be due to:

breakdown of the drain pump (pump);
clogged drain filter or pump;
contacts between the pump and the power supply are faulty;
the water level sensor is out of order.

In the case of stopping the drum, the most important reasons are:

wear of the drive belt;
malfunction of the electronics or control board;
it is very rare that the engine breaks down in such machines.

Drum noise can be caused by:

faulty bearings;
a small object stuck in the drum;
breakage of shock absorbers;
torn off counterweight.

When water is not collected in the washing machine tank, the following reasons are distinguished:

lack of running water;
blockage of the pump or Aqua stop system;
occurred by the kink of the drain hose.

The engine of the Bosch washing machine may not start due to a breakdown in the electronics or an open drum door... Having found out the cause of the breakdown and its severity, you can start repairing yourself.

If the breakdown is still not determined, we turn to the master.

Now we will describe in detail what malfunctions can be eliminated with our own hands, how to repair a car. Let's start with the simplest thing - a clogged drain filter. It is located at the bottom, under a panel or cover. To rinse it from accumulated debris, you need to open the lid by gently turning it counterclockwise. Be sure to use a large rag to prevent any leftover water from spilling onto the floor. Rinse the filter under running water and reinstall.

Cleaning or replacing the drain pump will not be complete without removing the front cover of the machine. This process is simple, but time consuming. This work is described in detail in the article on how to repair a pump in a washing machine.

With your own hands, you can eliminate the malfunction associated with the fact that water is not collected. First, we check if the water supply is turned off and if the water supply valve is open. Then the drain hose is inspected for kinks, and only then can the Aqua stop filter be checked. If it is not working properly, then it is necessary to replace it with a similar one.

If the water level sensor is broken, it must be replaced. The sensor is located under the top cover in the right corner. To remove the cover, it is enough to unscrew the two self-tapping screws from the back. The sensor itself is pulled out by pressing the latch. Then the hose is removed and the contacts are disconnected. A new one is installed in place of the faulty water level sensor.

How to replace a heating element in case of a breakdown? A similar malfunction can also be eliminated by hand. Opening the back cover of the washing machine, below, under the tub, you can see Teng. To replace it you need:

Unscrew the bolt holding the heating element to the tank.
Disconnect all wires.
We take out the ten.
We take a working ten.
Putting it all in reverse order.

More difficult is the job of replacing bearings in a Bosch washing machine. After all, you will have to almost completely disassemble the washing machine to get to them. In addition, tools and dexterity are required. A detailed video was filmed about this. All works in it are made by real masters.

One of the most common causes of engine stalling is drive belt wear. You can replace it yourself with patience and dexterity. This is done as follows:

open the back cover;

we take a photo of the drive belt and its correct attachment to the grooves of the pulley to make it easier to put on a new belt;

we grab the belt with our right hand slightly below the pulley and pull it towards ourselves;

with the left hand, slowly turn the pulley counterclockwise; with this movement, the belt will be easily removed from the pulley;

we get it out of the car body;

now we take a new belt and first put it on the engine;

we pull it with our left hand, and with our right we try to put the belt on the pulley;

while continuing to tighten the belt, turn the pulley counterclockwise, while trying to put on the belt to the end;

close the housing cover.

As we have noted, worn bearings, shock absorbers and a torn counterweight can cause drum noise and hum. We figured out the replacement of bearings, we will consider how to eliminate other malfunctions.

Before changing the shock absorbers, carefully inspect the drum of the machine, shining a flashlight inward, perhaps a foreign object is stuck in it, which can be pulled out without disassembling the body of the machine and the tank. Perhaps this particular object rattles during the rotation of the drum.

As for the shock absorbers, they, like in many other washing machines, change according to the same algorithm. There is a detailed article on this topic on how to change springs, shock absorbers and dampers.
If the noise is caused by a loose counterweight on the mount, then tighten these mounts. The counterweights are located under the upper housing cover and below.

If you cannot fix the counterweight, then you need to replace it with a similar one. This failure is quite rare.

German electric motors for washing machines are an example of quality that rarely breaks down, nevertheless, it happens.

There are two ways to solve the problem. The first involves dismantling the engine and handing it over to specialists for bulkhead and repair. There is a chance that they will be able to fix this expensive unit. If repair is not possible, then you will have to make a replacement, and in some cases this is almost 1/3 of the cost of a washing machine.

Getting to the engine is easy. You just need to dismantle the rear wall of the machine, then look under the tank, there is an engine with a drive mechanism. To remove it, you need to disconnect the supply wires and the sensor from it, and also unscrew the three fasteners that hold the engine. Before removing the engine, experts recommend checking the sensor capacitor for operability. To do this, arm yourself with a multimeter and connect its probes to the contacts. The value on the instrument panel should be from 20 to 50 ohms.

You will also need a multimeter to check the electrics of the washing machine. If you suspect a wiring malfunction, methodically check all contacts, terminals, plugs. With prolonged use of the machine, the wire could, for example, fray and create a problem - check everything, do not be lazy and you will be rewarded.

If you suspect a malfunction of the washing machine control unit, the only thing you can do is either call a specialist who will come and solve the problem, or dismantle the control unit and hand it over to a service center. Experts strongly advise against getting into the electronics of German technology: changing programs, reflashing, connecting to a computer and testing. To do this, you need to know many nuances - entrust this work to professionals.

What happened, why Bosch washing machines that have proven themselves on the market began to break down more often, because this is one of the most reliable companies? And all because some of the enterprises from Germany were transferred to Turkey and Russia, where they began to use cheaper parts.

For example, the metal tank was replaced with a plastic one, and some of the parts were purchased in China. Reducing the cost of products and led to a decrease in quality.

The German quality standard remains only in those washing machines that are assembled in Germany.

Therefore, when purchasing such a machine, you need to pay attention to where it was going. And if a breakdown occurs, then specialists will be able to repair the Bosch machine without any problems. Although partially, it is still Bosch.

So, do-it-yourself repair of an automatic Bosch machine can be overwhelming, in some cases you cannot do without the help of a specialist. However, serious breakdowns in this technique are quite rare; after all, Bosch washing machines are of high quality.And in each individual case of malfunction, you need to approach the repair creatively.

Is it possible to repair a Bosch washing machine with your own hands? Experts answer in the affirmative: in many cases, the owner of the unit himself, without special skills, can restore his working capacity.An increasing number of users have recently been interested in information on how exactly to do this.After all, the strategy of reducing the cost of production by transferring production to China and using cheaper materials could not but affect its quality. This article describes how to fix typical breakdowns, as well as measures to prevent their occurrence.Before proceeding with the repair, you should accurately identify the malfunction. Thanks to the self-diagnosis function, this task is solved today quite simply, because the washing machine itself can tell about the reason for the failure. In order for the unit to "speak", you need to perform a simple magic ritual:

After closing the door to load the laundry, turn the program selector to the “Off” position.

After a pause of 2 - 3 seconds, move the same switch to the "Spin" position.

As soon as the "Start" button LED starts blinking, press and hold the "Spin speed" button. In this case, you need to continue to monitor the LED - it should blink again.

At the signal of the "Start" button LED, the program switch is moved to the "Drain" position (the regulator is turned only clockwise).

We release the button "Spin revolutions" and using the program selector we tell the machine what exactly it should check:

to test the engine, the switch is moved to position "3";

drain pump: position "4";

Heating element: position "5";

hot water filling valve: position "6";

the same for cold water: position "7";

valve check during the main and prewash: positions "8" and "9", respectively.

In some models of Bosch washing machines, the assignment of positions may be different, for example, position "4" is sometimes used to check the engine.

Read also: Disk drive DIY repair

At the end of the test, an alphanumeric code will be displayed on the machine display, which can be used to determine the nature of the malfunction. In some cases, the owner can guess about a particular malfunction without the self-diagnosis function. Here are the most common symptoms and their causes:So, let's see what types of repairs are available to the average user. Image - DIY repair bosch maxx 4

The most prone to clogging is the drain filter. It is located at the bottom, approximately where the drain hose exits from the machine.

In most models, this element is closed with a lid, which must be turned counterclockwise to open.

It is necessary to clean not only the filter itself, but also the place of its installation - a lot of dirt also collects here.

The inlet filter can be easily found at the point where the filling hose is connected.

Before removing the drain filter, you need to spread a few rags on the floor underneath it: usually, during this operation, a certain amount of water is poured out of the machine.

This unit will become accessible after removing the front panel. Here's what to do:

remove the powder distribution hopper;
unscrew the screw located in the lower right corner;
remove the bottom panel by first unscrewing the screw near the drain filter, and then located at the bottom of it;
remove the hatch seal, after removing the metal ring fixing it (for this, you will need to bend a small spring with a screwdriver);
you can now remove the front panel by pulling on the bottom edge.

To get to the drain pump located at the bottom of the machine, it is necessary to disconnect the wires from the hatch lock. Next, the pump must be removed, disassembled and checked if a foreign object has fallen inside it. The impeller should rotate freely in both directions.

If it was not blocked, you need to check the resistance of the pump winding with a multimeter. It should be 200 ohms. Depending on the breakdown, the pump is repaired or replaced with a new one.

The Italian Candy washing machine has found its fans in our country because of the optimal ratio of price and quality for products. Small breakdowns sometimes occur during operation and it is not always necessary to pay the masters to repair the unit. Washing machine Kandy - DIY repair of basic faults, read on.

How to choose a compact washing machine for installation under the sink, read here.

What nuances you should know when installing a washing machine in the kitchen, read in this thread: https://my.housecope.com/wp-content/uploads/ext/740/cancliz/mnogokvartirnyie-doma/santehnika/kak-podklyuchit-stiralnuyu -mashinku-na-kuhne.html. Connection from the point of view of a designer and an engineer.

To access the heater in Bosch washing machines, you need to remove the back panel of the cabinet. Below on the tank you can see two contacts with wires connected to them - this is the heating element shank.

First of all, you need to check the performance of this element by measuring its resistance with a multimeter. It should be approximately 30 ohms. If the device shows "infinity", the heating element needs to be changed.

To remove it, it is enough to unscrew the nut between the contacts, having previously disconnected the wires. If the part is stuck, you can gently hit it several times with a rubber hammer. You can soften scale deposits with WD-40 liquid.

After removing the heating element, the edges of the hole inside the tank must be descaled. The next step is to install a new heater.

It is important to install a heating element designed specifically for use in your model. An inappropriate heater can burn out immediately, together with the electronic controller.

The inoperative pressure switch needs to be replaced, but you shouldn't rush into it.

Perhaps the sensor is working properly, just a plug of dirt has formed in the tube attached to it. In this case, it is sufficient to simply unclog the tube.

The level sensor is located in the right corner under the top cover (held by two screws on the back).

Measure the resistance of the sensor at room temperature, and then - in a heated state (you can dip it in hot water for a while). In a working sensor, the resistance should change.

For this operation, the machine will have to be almost completely disassembled.

During disassembly, do not disconnect the wires from the control panel - it will be very difficult to reconnect it. After dismantling, it can be laid on the machine frame or suspended on a specially made hook.

Dismantling the washing machine to replace the bearing

To remove the tank with the drum, you must first unscrew the springs, and not the elastic upper suspensions, as in the machines of some other brands. When disassembling the tank into two parts, the plastic latches have to be broken. The axle shafts are knocked out of the bearings by careful hammer blows on the wooden lining.

It is advisable to clean the drain pump and lubricate the bearing seals at least every six months.

To reduce the formation of limescale, a filter with a softening cartridge (it can be regenerated with the help of various substances) or a hydromagnetic system with a mechanical cleaning filter must be inserted into the water supply system in front of the machine.

Owners of Indesit washing machines periodically encounter minor breakdowns of the unit. Washing machine Indesit: do-it-yourself faults and repairs of some types of breakdowns will be considered in this article.

What types of country toilets and sewer systems are, we will consider in this review.

Technique always breaks down at the wrong time. If you have a question on how to disassemble a Bosch washing machine in order to check and repair it, use our tips. You will be able to independently inspect all parts and diagnose breakdowns, as well as replace defective elements. In the article you will find step-by-step instructions with photos and videos.Before disassembling a Bosch washing machine, you need to properly prepare for this. You must present the CM diagram and the elements that will have to be removed.The disassembly scheme is identical for different models of cars: Bosch Max 4 (Bosch Maxx 4), Bosch Max 5 (Bosch Maxx 5), Bosch Max 6 (Bosch Maxx 6).What stages of disassembly you have to go through:

Remove covers: top, back and front.

Pull out the detergent drawer.

Remove the control panel.

Dismantle the motor, intake valve, pressure sensor.

Disconnect connectors and wiring.

Disconnect connections and hoses.

Unscrew the weights and supports.

Remove the cuff clamp, take out the UBL.

Take out and disassemble the tank.

What tools do you need:

Screwdrivers: slotted, Phillips, hex.

Hammer, chisel.

Torx keys.

Nippers.

Pliers.

You need enough space to disassemble your Bosch washing machine.Disconnect the washing machine from the mains, turn off the water supply. Then prepare the container, unscrew the inlet hose from the CMA body and drain the remaining water into it. Go around the car, open the hatch on the bottom of the front panel. Unscrew the filter and drain the water.The preparatory stage is over, it remains only to move the washing machine so that it is convenient to move around.So, you have prepared everything you need, get to work.Take a Phillips or Hex screwdriver and remove the two screws from the back of the machine. Now slide the cover forward and lift it up. Be careful, the edges of the panel may be sharp. Set her aside.Moving to the front, pull out the powder dispensing tray. Pressing the latch in the center, pull it towards you and remove it from the case.Next, unscrew the bolts located behind the tray, as well as the bolts on the other side of the panel. Gently release the plastic clips (you can pry it off with a flat screwdriver), detach the panel. To completely remove it, you will need to disconnect the wire connectors - it is better to photograph them in advance. But it's easier to hang the panel from the side, on the service hook.Remove the bottom cover. It is located at the bottom of the front panel. To do this, it is enough to open the latches. Set it aside.First of all, open the hatch door. Before disassembling the door of the Bosch washing machine, remove it from its hinges by unscrewing the fastening screws. This must be done so as not to damage the glass of the sunroof.Bend the hatch cuff and, prying the clamp with a screwdriver, pull it out of place. Insert the sealing rubber into the drum.Remove the bolts securing the door lock. Place your hand behind the body and take out the UBL. Disconnect all wires from it and set the lock aside.Having unscrewed the self-tapping screws around the perimeter of the front panel, carefully remove it and set it aside.Using a screwdriver, unscrew the bolts around the perimeter of the cover, remove it. Behind the panel, you will immediately see the internal components of the Bosch washing machine.Unscrew the self-tapping screws of the upper bar that connects the two parts of the case. Using a 14mm wrench, unscrew the bolts and remove the upper counterweight. Do the same with the counterweights that are located around the hatch.How to disassemble a Bosch washing machine further? To get out the tank, you need to free up space as much as possible, and also disconnect all the parts attached to it.

To remove the cuvette of the dispensing tray, disconnect the pipe leading to it. If it has a clamp, use pliers to unclench it. Also remove the inlet valve tube.

Now disconnect the pressure switch and the noise filter. To do this, disconnect the wiring from the parts, unscrew the fastening bolts. Remove the tube from the pressure switch. Pull the parts out of the housing.

From above, the tank no longer holds anything.

Now you need to disconnect all fasteners and elements.

Remove the drive belt by pulling slightly towards you.
Disconnect the wires leading to the motor.
Remove the bolts that hold the motor to the suspensions.

Slightly swinging the engine from side to side, remove it from the case. Caution, the part is heavy!

It is necessary to lay the washing machine on its left side, remove the bottom (if any) by unscrewing the screws.

We disassemble the Bosch washing machine:

Use a pair of pliers to loosen the drain pipe clamp.
Disconnect it.Be careful, there may be water in it.
Unclip the wires leading to the pump.
Unscrew the bolts that secure the drain pump and remove it.

Little is left before dismantling the tank. Disconnect the wires from the heating element. The heating element in Bosch cars is located in the front, under the tank.

You do not need to pull out the heating element, otherwise you will tear the sealing rubber, which cannot be restored.

Sometimes wiring is attached to the walls of the tank, fastened with bundles. Bite the harnesses with wire cutters, move the wires to the side. Now you need to remove the shock absorbers.

Slide a knob over the back of the damper rod to push in the latch.
Pull the stem towards you with pliers and pull it out of the hole.

Do the same with the second shock absorber. It remains to remove the tank from the springs. Lift it up from the edges of the hatch and pull it out through the front compartment.

There is not much. Now we will tell you how to disassemble the drum of a Bosch washing machine with your own hands. Fortunately, the tank in typewriters of this brand is collapsible.

Disconnect the pulley. Install a prop to block the rotation of the pulley. Remove the center bolt. If it doesn't immediately respond, use the WD40 tool.
Remove the bolts around the perimeter of the tank that hold the two parts together.
Remove the top half.
Turn the bottom of the tank over.
Using a hammer on the stem, remove the drum.
The bearings are now accessible. If you need to get them out, remove the oil seal by prying it off with a screwdriver.
Place the chisel on the outer bearing race and hammer out in a circle.

During the disassembly process, you can carefully inspect all the details of the washing machine. In the event of a malfunction, they must be replaced.

Scale often forms on the walls of the tank and on the heater, which is now clearly visible. Before reinstalling, clean all elements well, thereby prolonging the life of your AGR. Otherwise, soon you will have to do disassembly again to replace the faulty element.

As you can see, you can do this kind of repair yourself. Therefore, if you are confident in your abilities, get to work.

A visual video on disassembling a Bosch car will help you:

Video (click to play).