In detail: do-it-yourself watch repair with amber from a real master for the site my.housecope.com.
OCHZ or Yantar watches were produced by the Oryol Watch Factory, which established the production of wall clocks in 1954, and ended its existence together with the Soviet Union. Therefore, offhand watches can be from 25 years to half a century.
- Analysis of the mechanism
- Parts washing and drying
- Grease
- Assembling and adjusting the clock
Think about disassembling the clock mechanism:
- first remove the pendulum and carefully detach the dial and hands from the central plate. Convenience lies in the fact that to repair a watch with an OCHZ strike, it is enough to pull out the mechanism located between the two plates.
- For rinsing, use high-purity Galosha Thinner, a cut-bristled toothbrush, and toothpicks to clean the holes.
- When assembling, it is difficult to swap the wheels, because they will not fit into someone else's place, but it is better to first find a clock diagram.
- Lubrication is carried out after assembly, but only with special watch oil or petroleum jelly, which can be sold in pharmacies. Little by little, all parts are lubricated, except for the gear wheels.
In the workshop, completing the repair of the Amber wall clock with a strike, they must check the progress and accuracy. Wall clocks are very sensitive to position. Therefore, when you hang it on the wall, move it to the right - to the left until a ticking sound is even audible.
Fix the position with screws that will not allow the watch case to move. Next, set the minute hand to 6 or 12 so that the clock chimes. Move the minute hand gradually, listening to the fight every hour. Set the exact time, wind up the watch, but not completely.
Now count how much the clock deviates from the exact time per day. The accuracy can be adjusted using the adjusting nut located under the pendulum lens. On average, one revolution is 0.5 minutes to one, we turn to the right to increase, to the left - to decrease.
 |
Video (click to play). |
The factory producing most of the large-sized watches in the USSR was the Oryol Watch Factory. On many watches on the dial was the abbreviated name of this plant "OCHZ". The factory began to produce watches Amber in the late 60s. The watch became very popular among the citizens of the Soviet Union. Nowadays, they still use this watch, this speaks of the good quality of the mechanism, because with proper operation and timely prevention, the Amber watch with a pendulum can last at least 100 years. A watch was brought to the Fullfix watch center for repair after a long stay in the attic. Corrosion has strongly eaten the chrome-plated elements of the case, we will carry out restoration and repair of watches. Let's start with the watch case.
As you can see, there are traces of paint on the body, most likely due to storage in the attic, corrosion has appeared on the chrome parts.
The condition of the case and chrome-plated parts leaves much to be desired, there is also corrosion on the dial elements.
The pendulum is covered with a layer of rust.
We will remove rust from the case and dial elements by polishing with abrasive wheels.
Let's pay attention to the striking strings of our clocks, as we can see the time also did not pass them by, we will carry out the restoration of the "voice", our clocks.
From the exterior of the watch, let's move on to the internal mechanism. Dust has adhered to the old watch oil and an unpleasant "mess" has formed, we will disassemble and clean everything.
In the process of parsing, we notice the absence of a pawl spring on the mechanism. Repairing antique pendulum clocks is not an easy task these days, you have to make some spare parts yourself, as new ones can no longer be found. We make the spring ourselves and solder the missing end to the old piece in platinum.
We disassemble the watch and wash everything in a special solution.
We assemble and lubricate the mechanism.
We insert the mechanism with the dial into the watch.
After restoration, the watch took its original appearance, the watchmaker №1 in Sokolniki Fullfix coped with its work perfectly.
A person constantly monitors time, not even paying attention to it. He casts a fleeting glance from the car window at the street display, at the dial of a wristwatch, keeps track of the progress of time on TV, computer, telephone. Now you will not meet a passer-by on the street asking: "What time is it?"
However, there is something touching in the old chiming clock of the last century, which makes you stop for a moment and count the number of strokes, and then look at the dial, checking yourself to see if it is going.
The striking clock of the Yantar plant can sometimes be found in the apartments of people who have managed to preserve the relic. It is possible that the fight will interfere with the household at night and it is better to hang such a clock in the living room, but it is important to properly care for them so that the clock will last a long time and be inherited by the future generation. In order for the clock to run correctly and not to disrupt its movement, it should be hung on the inner wall, in which there is no door, and it is not subject to vibration. The striking watch should be fastened exactly without distortion, in this case the strikes will be uniform.
The watch, which is almost half a century old, has definitely fallen into the hands of a watchmaker more than once. They remember the touch of the caring hands of an experienced craftsman who loves his work, and the rough inept attempts to fix them by a self-taught person who knows little about the mechanism of a watch.
Now you can safely entrust the Yantar watch with a break to the service center, which employs professionals. Specialists will test the watch, repair it, replace the damaged parts of the mechanism with new ones and provide them with warranty service. After visiting a trusted company, the watch will work like new and delight its owners.
The pendulum mechanism is durable and unpretentious, with proper care it can work for a long time, but it needs cleaning every two to three years. The dirt that has accumulated in the watch parts over several years affects the operation of the mechanism, the movement is thrown off, the hammers, briskly beating their song every hour, sound more dull, which means the time has come for cleaning.
In the service center “Tochnoe Vremya”, the watch “Yantar” will be repaired and cleaned by masters using the latest technologies and tools used for watches of elite brands. The final touch for every master is checking the progress and accuracy, special attention is paid to the striking wall clock, due to its design features. After the workshop, you need to fix the watch on the surface in such a way that there are no distortions and the efforts of the masters are not in vain.
How to fix an old wall clock
Watch Amber 1965. Oryol Watch Factory (OCHZ Yantar).
Oryol Watch Factory "Yantar" - a plant in the USSR, produced large-size floor, wall and table mechanical and quartz clocks. The Oryol Watch Factory also produced alarm clocks.
The first batch of products was released in 1952.
In the 2000s, the plant had financial problems and soon ceased to exist.
For many years now, we have had a wall clock with a Soviet-made pendulum hanging in our houses. Hanging, but not walking. After winding the springs and starting the pendulum, they stop and do not move, so I decided to fix them. It took me a lot of time, I will try to briefly tell you about it.
On the advice of dear members of the forum, I took off the dial and hands, unscrewed the anchor and set the mechanism to soak in Kalosha gasoline. After that, they had to go, but still something interfered with the move.
After repeated attempts to start the clock, I "hammered" a little on them. But the other day, passing through the courtyard, I saw a thrown out watch. Amber, also pendulum, but without a fight and the pendulum itself.But in them there was a detail on which the pendulum itself is attached, and the same one as in my watch. Naturally, I picked them up. I had doubts about this part for a long time, it was all wrinkled, loosened, in general, with signs of use.
So, having replaced the pendulum holder and the rope on which it is hung, I tried to start the mechanism. And lo and behold - the clock has gone. True, five minutes later they got up again. But it was 5 minutes!
After repeated advice with the members of the forum, I aligned the clock not by a plumb line, as I had done earlier, but by ear, to a uniform "tick-tock". And the clock went on. Now it's okay, without stopping. Adjusted the hammers for the right fight, now they signal to me the new hour has arrived.
AMBER watch with striking. main causes of breakdown. and elimination.
Repair of striking watches, shown on the example of watches Yantar, Oryol Watch Factory (OCHZ).
the next clock came for repair.
How to fix an old wall clock Amber clock 1965. Oryol Watch Factory (OCHZ Yantar). Orlovsky.
Repair of striking watches, shown on the example of watches Yantar, Oryol Watch Factory (OCHZ).
The wall clock "Yantar" came to me for repair. I had to dig around the boy, testing the mechanism in operation.
HOW TO REPAIR AN OLD PENDULUM CLOCK.
Clock mechanism OCHZ 1957 with a fight. After service. Combat levers stand from late Amber. The fight is not set up.
AliExpress: https://ali.pub/2rqu34 My affiliate: Commerce: CashBack:
To adjust the clock, I used the Android program "Clock Tuner". A very useful program for configuring how.
They brought the watch here for repair, the fur was profiled.
