DIY Chery Tiggo T11 repair

11.12.2015, 17:21 1.1k Views

If the fuel pressure regulation sensor (RTD) on the Chery Tiggo is out of order, it is not necessary to buy a new one, all the more it is costly, since it is very difficult to find the sensor separately.

But you can repair the old one, especially since its device is very simple - a spring, but a diagram. How to do this, see a short video

And in this video, the author shows where to find, how to remove the RDT sensor itself and replace it - the whole process from removing the fuel pump to removing the sensor and reassembling the entire structure.

By the way, you can identify the problem at any service station or even on your own, just connect a test computer and read the error codes.

Copying design and borrowing technical solutions, engines and even platforms from eminent automakers is a feature of many Chinese cars. One such example is the Chery Tiggo, which has become a quite successful reincarnation of the second generation Toyota RAV4 crossover. Let's check how things are going with its maintenance? We assess maintainability in points - they correspond to the total standard hours (according to the official grid) spent on certain operations.

There are two gasoline engines and two types of drive available for the Tiggo in our market. The older 2.0 engine is paired only with an all-wheel drive transmission and a five-speed manual gearbox. Unfortunately, we were not able to touch this modification due to the extremely low demand for it. Most dealers do not keep such machines in their warehouses and only bring them to order.

But the most demanded Tiggo was dismantled to a screw: with a 1.6 engine and no alternative front-wheel drive - such versions come with both a variator and a mechanics.

Regardless of the configuration, the Tiggo has a very peculiar maintenance schedule. The time interval is the usual year, and the service mileage was reduced to 10 thousand km. In addition, the list included works long forgotten by most manufacturers with suspiciously frequent deadlines.

The 1.6 petrol four with a maintenance-free timing chain drive was created on the basis of the Mitsubishi engine, which was slightly modernized, equipped with two variable valve timing couplings and a variable-length intake manifold.

Surprisingly, all attachments are driven by one belt. It is fortunate that there is an automatic roller tensioner with a quite convenient release mechanism. When replacing the belt, be sure to sketch or photograph how it stood, otherwise you will waste a lot of time later without prompting. We change the belt from below, additionally removing the side boot.

An interesting ignition system is used on this engine, again borrowed from Mitsubishi. Two-lead coils are installed in the wells of the second and fourth cylinders. Outwardly, they resemble individual ones - with one lead the coil sits directly on the candle, and the high-voltage wire goes to the neighboring "pot". There will be no problems with replacing candles (according to the regulations - every 20 thousand km). All this exotic is covered only by a decorative motor cover on simple clamps.

The coils are fixed with bolts "8", and their connectors have simple fastenings. For candles you will need a familiar "16" head.

Strange, but the regulations do not indicate the timing of replacing the engine air filter. And he usually does not live more than 20 thousand km. The upper filter cover is fixed with two self-tapping screws and three projections in the grooves on the lower housing. When replacing the filter, it is enough to unscrew the fasteners. Lift the cover, but do not remove it from the case, otherwise you will then fall into the grooves for a long time.

Antifreeze replacement is prescribed every 40 thousand km - very often! Fortunately, there is a divine drain plug on the radiator. Additionally, we remove the half of a small boot on the bumper under it.

Pleased with the presence of a separate filter outside the tank. The fuel lines are fixed on it with convenient quick-release couplings. To remove the filter, unclench the metal bracket that tightens it and unscrew the "ground" wire, fixed to the body with a bolt "8". It would seem that everything is fine, but the matter is overshadowed by the ultra-short interval for replacing the element - every 20 thousand km!

I was also struck by the presence of a mandatory operation to update the power steering oil. Of course, sooner or later, the grease needs to be changed (despite the fact that it is supposedly designed for the entire service life), but not as often as the "Chinese" require - first at 20 thousand mileage, and then every 40 thousand!

The service of the mechanical box also excelled. The oil change interval is 30 thousand km. Even for serious off-road vehicles, it is not updated with such enviable regularity. It's good that the usual drain and filler plugs are provided. The normal oil level is at the lower edge of the filler hole.

Even the variator has a life of its own. Not only is it designed to use conventional ATF fluid for hydromechanical automatic devices, it also provides for only one oil change per 40 thousand kilometers. Aggregates of this type are quite whimsical - that's where you shouldn't be limited to just one fluid update! At the same time, the procedure is quite simple - everything is like in the usual classic slot machines. There is a normal drain plug and even a good old dipstick (also a filler hole). Only its location let us down. It comes out almost under the engine air filter housing, and it is difficult to reach it with your hand, let alone the oil fill. Well, at least it won't be difficult to remove the case. It is fixed on the sides with two “10” bolts and a regular clamp on the throttle body.

The battery is fixed by the upper bar on two studs with nuts "10". Regular terminals are not overloaded with additional elements. Everything is removed quickly and without problems.

The Chinese were too clever with the location of the engine compartment fuse box. He was pushed into the right cup (upper suspension strut support). The block covers a separate part of the "frill" (cover under the windshield), fixed with four caps for a Phillips screwdriver. It is inconvenient to put it back - it is difficult to immediately hit the ledges under the glass. The fuse box cover is secured on the sides with two latches. It contains the English-language designations of the chains and their spare protectors. The cabin unit is located under a simple cover on the dashboard (bottom left). But, unfortunately, there are no designations or spare fuses on it.

All brakes are disc brakes. The calipers are secured with bolts "13". Replacing the front pads - no surprises, and at the back there is a nice bonus - no recessed pad is needed. The pistons are brought together without rotation with an improvised tool. Replacement of brake fluid - every 40 thousand km. The fittings are conveniently located.

Replacing lamps in front optics is a thankless task. Free access is only to the turn signals. Their sockets are located in the inner corners of the headlights near the radiator grill and are secured by turning. The rest of the lamps have a simple fixation, but it is difficult to crawl up to them. Burnt out diode running lights must be replaced along with the optics.

Access to the right headlight is severely limited by the antifreeze reservoir. Fortunately, he effortlessly comes up from the mounts. If this did not help, then you will have to remove the optics, partially dismantling the bumper.

The trouble is with the front foglights. It is unheard of that to replace lamps you had to not only remove, but also disassemble the headlight! Access to lighting equipment is only from below and from the side, and it is necessary to partially dismantle the fenders.

There are no problems with the lamps in the taillights.The brake lights in them are diode, as in the additional element on the rear door. Access to the rest of the lamps is through the niches in the sidewalls of the trunk. They are closed with lids with simple latches. Under them are large plastic plugs that can be removed by hand or prying off with a screwdriver.

With the rear fog lights, too, not everything is smooth. They are located in the corner portions of the bumper and the pivot-secured lamp holders abut against the body panel. Accordingly, the headlights will have to be removed along with these corner bumpers. The operation is time consuming.

Chery Tiggo FL scored 15.5 points - a mediocre figure. And this despite the fact that the car is surprisingly easy to maintain, as in the good old days. The barrel of honey was spoiled by annoying fly in the ointment: a mysterious maintenance schedule with very short intervals for changing liquids and ridiculous difficulties with replacing lamps in optics.

The editors would like to thank the technical center "Cheri Center Kashirsky" (Moscow) for help in preparing the material

The car manufacturer Chery Tiggo recommends changing the drive belt every 40 thousand kilometers. Next, we will consider how you can change the timing belt on a car with an Acteco 1.8 engine on your own, without resorting to the services of a car service. Replacement tools [. ]

Cherie Tigo's native clutch, to put it mildly, is not very good - it wears off quickly. Verified by personal experience. It was decided to purchase a similar Valeo clutch kit. Estimated cost - 5,000 rubles. Replacing the clutch yourself is hellish [. ]

I decided to replace the fuel filter on my Cherie Tigo, but figured that there was no store nearby with spare parts for Chinese. There are still shops designed for foreign cars, but as far as the Chinese are concerned, you even have to order consumables and [. ]

Experienced car enthusiasts know that front brake pads wear out much faster than rear pads. The need to replace the brake pads is indicated by an extraneous sound that occurs every time the brake pedal is pressed. However, Chery Tiggo vehicles are equipped with sensors [. ]

The procedure for pressing out silent blocks and replacing them with new ones is quite time consuming on all lines of the Cherie Tigo model. This operation is recommended to be performed at a service station. If you are confident in your abilities, then here is a video replacement instruction [. ]

When a belt breaks, nothing criminal, as a rule, happens. It's just that the car cannot be started from the spot, only from the pusher. Another thing is when the generator itself is broken, which, according to the standard, should produce 14.2 volts, regardless of [. ]

On the odometer - 93,000 km. Several times I tried to scribble a thread, but somehow there were good reasons to postpone everything. And even now I remembered that there was not enough photo, but I just started.

The most burning question for Chinese breeders is probably reliability. My last report, I remember, was at 75,000 km, and so, since then:

1. Replacing the front hub bearing - hummed desperately. In fact, I replaced both - because of my arrogance and greed ((. By all indications, the left one was buzzing (the sound, as it seemed to me, came from the left, and the buzzing stopped at the left turn, i.e. when the left wheel was unloaded.) - I and I decided to “save money” on diagnostics from an official.

Yes, in general, nothing. In the fall, I changed the brake fluid, antifreeze and oil.

Antifreeze was only TCL, and it was poured.

This time the oil was filled with SHELL HELIX HX8.

The brake is still the same Ravenol.

The oil has shown itself well in the winter. This time in cold weather did not even warm up. As soon as I arrived at work in the morning, put it on, scratched it in the evening and drove home.

1) Started up easily in cold weather. I didn't ride in cold weather, I felt sorry for the suspension

2) In October, the left drive oil seal was sweating. I went to change and it turned out that the previous owner had poured an extra 3.5 liters of oil into the box) - I had to drain and refill everything, poured in good oil, 700 rubles per liter. I was greedy and broke a simple rule, bought a used equipment, change fluids and filters. It's good that I just got off with an oil seal.

3) The crack on the frontal was spreading, in the cold. Well, actually expected.

4) The roads to Nska are not cleaned, but what a thrill it is when you don't care) - you just drive, I don't even have a shovel, I just drive and leave everywhere.

Good day, dear readers! There was absolutely no time to complete my review. There have been several important events since the last addition to the operation of the car was written, which would be worth talking about.

The first pleasant event is a vacation, a trip to the sea at the beginning of August 2017. What I want to say, my family and I were not going to go somewhere to rest until the last moment. Planned to do household chores. But, the less time remained before the onset of vacation, the more often thoughts began to come to me that I still needed to jerk somewhere, because decent fatigue had accumulated and it was necessary to urgently change the situation and try to relax mentally and physically.

The stable operation of the car, fuel consumption and engine power directly depend on the condition of the air filter. A clogged cartridge does not clean, and then does not pass a sufficient amount of air to the engine. This leads to a number of problems that will be described in the article.

Replacing the Chery Tiggo T11 air filter is an important procedure in car maintenance. How to change the engine air filter with your own hands, the sequence of actions and tips for choosing a filter are presented in the article. Become familiar with the consequences of untimely replacement of the air purifying element to prevent breakdowns and avoid repairs.

How often do you need to change the air filter? It should be borne in mind that if the car is operated in the absence of increased dustiness, a small number of plugs, then a filter replacement is required. every 30 thousand km of run... In the realities of Russian roads, the period must be shortened up to 20 thousand km due to dust, dirt on the roads, and often lack of asphalt. The replacement period should be reduced to 10 thousand kilometers if the car owner lives in a rural area, which is characterized by many fields, or if he lives in a large city and often gets stuck in traffic jams.

The car needs oxygen to help the fuel burn properly inside the cylinder system. To properly burn 1 kg of fuel, it will take up to 20 kg of air.

It is not surprising that by passing so much air through the filter element, it quickly clogs up when used in difficult conditions. So, when a replacement is required, the driver will be prompted by the engine size and type of car, and the environmental conditions, as already mentioned. Do not forget that the surrounding factories also pollute the air.

Summarizing the above, signs of need for replacement Chery Tiggo T11 filters are as follows:

• enrichment of the mixture, its incomplete combustion, which means increased fuel consumption;
• the power indicators of the motor have significantly decreased;
• increased content of toxins in exhaust gases.

Another way to determine if the filter needs replacement is by visual inspection.

It is not necessary to know when to replace the filter. Taking it out of the Cherie Tigo T11 case and examining it, you can come to the conclusion - use it further or replace it. The cleaning material must not be clogged, it must be free of traces of oil or leaves, dirt, insects, etc.

Advice to car owners: change the air filter every oil change, the frequency of which is 10 thousand kilometers. If, after examining the part, the driver decides that the deadline has not yet arrived, then it is not possible to change every oil change, but every other time.

If the engine is a turbocharged diesel engine, then special requirements are imposed on air purification, which means that the filter element is changed more often. It is recommended to inspect the part after 6 thousand kilometers to replace it if necessary. The shortened service life of the air filter is also relevant for diesel engines and machines with a turbine.

Early replacement of the Chery Tiggo T11 cleaning element will help maintain the engine's power performance, save the car owner from repairs and waste.

You should not save on a filter that cleans the air entering the engine. Replacing the unit will cost the driver more. Preparation for work on replacing the filter includes, first of all, the choice of the air filter and the selection of the necessary tools.

Filter selection

Such a spare part as an air filter for Chery Tiggo T11 with a 2.4l 4G64 engine. 129 hp, produced since 2005, purchased in the original or a good duplicate that completely copies the geometric and quality characteristics of the filter.

Original air filter Chery Tigo T11, article T111109111. Suitable for cars with 2.4L 4G64 engine. 129 h.p. Manufacturer - Chery, country - China.

Air filter (analogue) Chery Tiggo T11, article GB9507 Big Filter. Suitable for cars with 4 G64 2.4L engine. 129 h.p. Manufacturer - Big Filter, country - Russia.

Air filter (analog) Chery Tiggo T11, article FA033 Fortech. Suitable for cars with 4 G64 2.4L engine. 129 h.p. Manufacturer - Fortech, country - Korea.

Required tools:

• middle Phillips screwdriver;
• clean rags;
• wet rags;
• new filter;
• new housing (if damaged and needs to be replaced).

This completes the preparation procedure for replacement. You should start the process of replacing the air purifying element, step-by-step instructions are presented below.

The procedure for removing the air filter and installing a new cartridge will take up to 20 minutes from the car owner.

The sequence of actions when replacing the filter with Cherie Tigo T11 is as follows:

• unscrew 2 bolts, also disconnect the tube leading to the engine by removing the clamp, since it does not always allow you to remove the housing cover;
• the old filter is removed;
• wiped with a wet rag and cleaned of any dirt inside, filter housing;
• a new filter is installed in the housing;
• make sure it snaps into place;
• fix the cover back;
• tighten 2 bolts;
• connect the tube leading to the engine.

What type of filter does not change, after removing the cartridge, it is imperative to wipe the inside of the case with a damp cloth or blow it with a vacuum cleaner to remove traces of dirt. Doing so will help prevent dust from entering the engine intake manifold.

After installing the cartridge in the housing, make sure that it fits clearly into place, check the location of the filter. If it is skewed, some of the air will enter the cylinders uncleaned, which will negatively affect the condition of the valves and the cylinder-piston group.

Do not ignore the replacement frequency or skip it, as the consequences will force the driver to spend money, time and effort on repairing or even replacing the power unit of the car.

We will describe in detail the process of engine failure due to ignoring the timing of replacing the air filter on the Chery Tiggo T11:

• the car loses its power capacity. The reason - the walls are clogged, and this does not allow a sufficient amount of air to pass into the cylinders;
• poor combustion of fuel due to lack of oxygen in the cylinder block;
• decrease in engine efficiency;
• the motor starts harder each time;
• unstable idle speed;
• gasoline consumption is increasing;
• dirt, dust, insect bodies will fall from the walls of the clogged filter into the cylinders and scratch its walls, which leads to poor slipping;
• depressurization of the combustion chamber, loss of force and compression;
• failure of the rings;
• overhaul of the engine.

Inexperienced car owners can inadvertently bring the car to such a state. But experienced motorists, after a couple of times in vain attempts to start the engine, immediately check the air-purifying filter and replace it if necessary.

The refinement of Cherie Tigo in the FL modification, like tuning other Chinese cars, is best to start with the engine rework. Having “bewitched” over the power unit, you can proceed to work on the brakes and the car body. Let's find out what awaits those who want to improve the Chinese SUV and how to do the technical part of the modernization with their own hands.

Quite often, Cherry car owners find themselves in situations where the car simply won't start. And this despite the fact that it is not freezing outside, there is enough engine oil, the car has not run over a lot, but the power unit of the car stubbornly does not start. And even if it starts, the Tiggo shows a rather sluggish acceleration, the appearance of floating revs and an increase in fuel consumption. Many attribute these problems to low-quality gasoline, however, as practice shows, the cause of the FL model malfunction lies much deeper.

Almost all representatives of the Tigo FL model range are equipped with 16-valve motors with IKZ. Experts call a bad spark one of the main disadvantages of such engines. A similar problem makes itself felt after the first six months of Chery operation. As a result, dips appear in the accumulative phase of the ignition coils, lasting no more than 3 ms. Despite the short duration, the swing of the dips sometimes reaches about 5 V, which is more than noticeable at high speed. A decrease in the maximum accumulation during a rupture by as much as 18% is equivalent to a decrease in the energy in the coil. As a result, the coil gives 33% less energy to the candle than required.

It is possible to solve the problem with your own hands by tuning by installing capacitors. Moreover, it is necessary to look for a place for their installation as close as possible to the center of the load. In addition to installing capacitors, the circuit that powers the Tiggo ignition coils will also need to be reworked. Fortunately, this is also very easy to do without the help of specialists.

Having figured out the cause of the problem and how to fix it, you can go to the store. For tuning, we need to select 2 capacitors with the following characteristics:

• voltage range from 35 to 63 V;
• capacitance limits 3200–4700 μF;
• parts must be low impedance, marked LowESR;
• it is better to give preference to the products of firms Samwha, CapXon or Jamicon.

After the purchase, the most interesting begins, namely the preparation and installation of capacitors. To begin with, the conclusions of the parts must be twisted and the wires must be soldered. Finished parts must be insulated with heat shrinkage. Tuning by installing elements can be done in two ways.

The first of them consists in cutting the electrical tape of the bundle under the corrugation of the coil located between the second and third cylinders of the Tigo FL. There we find several blue wires, one of which is marked S1. You need to connect the pluses of the previously twisted capacitors to this wire.

The second method relies on soldering the positive leads of the capacitors to the blue lead that emerges from the ECM connector. In both the first and second cases, the minus wiring of the capacitors must be soldered to the point of mass under the M6 ​​bolt. The point we need is near the Cherry oil pressure gauge.

After installing the capacitors, we proceed to the next stage of tuning - reworking the power supply circuit of the Tiggo coils. Initially, the circuit consists of a large number of different wires and has 4 connectors. Power to the latter comes from the ignition switch. This principle of power supply negatively affects the resistance in the coils. In order to solve the problem, you can supply power to the coils from the main relay of the engine control unit. To do this, you need to find a crimp with the inscription S5. In Cherry cars, it is located between the ECM harnesses towards the dashboard.

As soon as you find a wire with this marking, you need to disconnect it from the general connector and pull it towards the Chery engine shield. Next, we connect the wire to the ECU relay, having previously replaced the 33rd fuse from 7.5 A to 10 A. After the work done with our own hands, we get high dynamics when accelerating the SUV. Dips disappear automatically, the car reacts better to pressing the gas pedal. The Chery engine will idle better, and fuel consumption will be reduced by about 0.8-1 l / 100 km.

Initially, the Tigo FL is equipped with a dual-circuit hydraulic braking system. A special pressure regulator, popularly nicknamed the "sorcerer", is responsible for the stable operation of the rear brake discs. This part is considered one of the weakest components of Chery brakes. We propose to consider the principles of tuning the brake system, replacing the regulator and remaking the two-circuit-diagonal structure for a two-circuit-axial one.

The main role of the “sorcerer” is to create force in the rear of the PL braking system, depending on the severity of the braking and the load on the Tiggo. In a standard suspension, the regulator can be easily adjusted to certain settings. However, even having slightly exceeded the allowable vehicle load, you can forget about the presence of a “sorcerer” in Chery. As a result, almost every third Chery has serious problems with the brake system.

Tuning a Chinese SUV is carried out in 2 stages. At the first stage, we will be converting the brakes to a dual-axis system. The second stage will consist of replacing the regulator with a better part from Chevrolet lanos.

The Tiggo dual-circuit diagonal braking system at its rear is equipped with two special tubes that are connected to the discs. In order to turn the machine system into a two-circuit-axial one, it is necessary to plug one of the pipes on the main brake cylinder. In this case, we leave the "sorcerer" for now, closing his pipe. You can also replace the regulator with a T-piece. As a result, we get a more stable and even operation of the rear part of the Chery braking system, that is, after tuning, all 4 wheels of the FL model will brake equally with maximum effort.

In the second step, we will install a Lanos regulator on the Tiggo. The only drawback of this method is the need to seek help from a familiar turner, since the hole and thread for the pipe from the Chevrolet are not suitable for mounting on the Tiggo. We also need an adapter with which we can screw the tubes on both sides of the regulator. So, it is necessary to remove the Chery rear wheels and dismantle the brake discs. Just above the wheel arches is a regulator that we have to remove. In the form of a regular "sorcerer" you need to file a detail from Lanos. Next, we mount a new element and fasten the wheels.