DIY wooden window frame repair

In detail: DIY repair of a wooden window frame from a real master for the site my.housecope.com.

Many modern people strive to make their home as environmentally friendly as possible and are in no hurry to replace their usual wooden windows with new plastic. And this is not surprising, because wood is considered a valuable natural material with a lot of advantages. One of its main advantages is the possibility of repair. The restoration of wooden windows is not an easy task, but it can be solved. It makes it possible to give the old structure the appearance of a completely new product.

Do-it-yourself wooden window restoration allows you to save your budget and improve the dilapidated window structure. Before starting the repair, it is necessary to take into account the "life" of the material from which the frames are made. Larch and pine can last no more than 35 years, oak and beech - more than half a century.

Restoration of wooden windows is unlikely to lead to the desired result if:

The structure of the wood is so loose that when pressed, strong dents are formed;
There is a complete loosening of the window frames in the openings;
Large dark spots are visible under the paint, which are usually indicative of dust and decay;
Frames are bent or strongly deformed;
Wooden windows are severely damaged (for example, cracked frames).

After reconstruction, the old window looks like a new one

The restoration of old wooden windows is usually carried out according to the "Swedish" system, which allows combining the repair and thermal insulation of the window structure... To work, you will need a certain list of tools:

Selector (zenzubel) - a plane for the formation and cleaning of grooves, folds and claws;
Several chisels 4-30 mm wide;
Saw blade 0.3 mm thick and 4-6 mm wide;
Palette knife or flat knife (boot);
Carpenter's Square;
Core drill for wood (8-10 mm ID);
Level and plumb line.

Video (click to play).

For a high-quality restoration of the structure, you need to stock up on special tools

About 300 grams of "liquid nails";
Drying oil;
0.5 kg of wood putty or 0.5 kg of fine sawdust;
Zinc or titanium thick-grated white;
Kerosene;
Brushes;
Carnations (500 gr. Small and 60-80 mm);
Sandpaper;
Plywood or board board slightly larger than the window frame;
Plastic bag 0.5 m wide, 1.7 m deep;
Pieces of water-repellent plywood with a section of 1-1.5 mm;
Silicone based aquarium glue - 10-20 ml.

A plastic bag and kerosene will not come in handy if you use a factory hair dryer. It is not recommended to use deep-penetrating polymer putties on wood on water, as they will significantly increase the thermal conductivity of wood parts.

It is better to start repairing wooden windows with your own hands in warm, not damp weather. Recommended humidity - 40-65%... In the event of bad weather, window openings must be temporarily tightened with waterproof material.

The repair of wooden windows begins with an inspection and check of a double-glazed window. It is necessary to remove the sash, remove the glazing beads or remove the putty, remove the glass.

Repair begins with inspecting the surface of the frame and removing the old putty.

Dismantle the fittings (a new one will be installed in its place). Carefully remove the external wooden sills, remove all fasteners and iron squares.

Window restoration should only be started after thorough drying of all wooden parts..

There are several methods to remove paint from old-style windows.

Removal of the coating must be done carefully and carefully. It is recommended to remove the glasses in advance, as they can crack if hot air is directed.

The recommended temperature of the hair dryer is 250 0C. With increased values, the wood will char and lose its characteristics. When heated, the paint will begin to bubble and can be easily removed with a professional knife or palette knife.

The most effective method of removing paint is considered to be the use of a building hair dryer.

Old wooden windows will not withstand the aggressive effects of solvents or solvent, therefore, only kerosene should be used to remove paint:

Wrap the wooden frame with fabric material and lower it into a plastic container;
Thoroughly moisten the cloth with kerosene, close the container and leave for a couple of days;
Remove the strips one by one and remove the paint. If all the parts are pulled out at the same time, then the kerosene will evaporate, the paint will harden again and stop flaking;
Remove any remaining paintwork with an emery cloth or grinder.

It is recommended to use kerosene as a chemical solvent.

The decayed section of the frame can be replaced or restored. An epoxy wood filler is required for the restoration. The damaged area must be freed from paint and debris removed. Then apply the putty, carefully filling all gaps and cracks. Form the missing part. It should be slightly larger than the required size, since the excess will be removed during subsequent grinding.

If the decayed area cannot be replaced, the defect is eliminated with a putty

Leave the frame to dry for at least a day. Sand the repaired area with sandpaper or a grinder.

It should be understood that such a repair of old wooden windows helps to restore the appearance, but does not provide the necessary reliability, especially in areas of active use. But on a blind or rarely used window, this method will allow you to restore the structure without a cardinal replacement.

Before carrying out this operation, it is necessary to identify cracks, chips and other defects in wooden windows, mark them with a marker and process with sandpaper. Then cover the marked areas with latex or oil putty. The work is carried out with a rubber spatula, immediately removing excess material. If necessary, after the first layer has dried, apply the second one. At the end, the wooden surface is treated with fine-grained sandpaper. The primer is applied in 2 layers.

In order for the repaired old and Soviet windows to serve as long as possible, they need to be coated with linseed oil... It will block the development of new embryos of rot and, if possible, restore the structure of the old wood.

Coating with linseed oil will extend the life of the window frame and prevent the formation of rot

The drying oil is applied with a brush in 3-4 layers: the next one - after the absolute absorption and drying of the previous one... Such processing will last for 2-3 years (until the next repair). Impregnation for many decades has been carried out in a piece of iron pipe 10-12 cm thick, sealed at one end. All actions must be performed only on the street, away from residential buildings.

Install the pipe at an angle of 300, fill ¾ with linseed oil and heat from below with hot air from a hair dryer or electric stove. As the temperature rises, the drying oil will begin to swell - this will release moisture and air. If there is a sharp increase in the smell, you need to move the heater aside and wait a little. Impregnation begins after the bubbles disappear:

Prepare an iron hook with a sharp end, 5-6 mm thick;
Place the part in the pipe and press it down with a crochet hook for 4-5 minutes;
Hook the bar with the tip of the hook, remove and lay to dry;
It is forbidden to touch the parts with your hands (even with gloves), since the temperature of the hot drying oil exceeds 130 degrees.

Such processing allows extending the service life of wooden window frames by more than 100 years, and if they are coated with an oil composition, then repainting will be required no earlier than 15 years later.

The prepared sashes are laid on the board and carefully aligned to squareness. Particular attention should be paid to the details of the vents: a 1 mm difference in the diagonals will provide a 0.7 mm gap.

The leveled area is fixed with glue or nails, carefully driving them into the shield near the sash. They are looking through the old pins ("chopiks").

When assembling the sashes, it is necessary to strictly observe the rectangularity

Drill them in the middle of the corner using a larger diameter drill. If any of the pins is shifted to one side, then you need to:

Fasten it along the border with a few drops of "Super Glue";
Drill the correct location;
Stretch the saw band through the slots between the fixing bars and saw through the old nail.

After assembling all the corners, you should get a fairly rigid structure. Now you can take the frame and install the sashes into it. They will sit more tightly if plywood strips of the appropriate width and thickness are glued to the frame.

Place all parts on a leveled canvas and press down with a load (approx. 100 kg). Leave to dry and level for 2-3 days.

High-quality repair of wooden double-glazed windows includes their insulation, which can significantly reduce heat loss at home. You can insulate windows with your own hands in several ways:

Silicone sealants;
Special paper;
Cloth stripes;
Tubular profiles;
Heat-saving film;
Seal in the frame sashes.

The last two methods are considered the most effective. First, the joints of the sash and glass are covered with silicone sealant. Then they take a milling cutter and cut a 5 mm depression along the perimeter of the sash at an angle of 450. They clean it from shavings. The PVC sealant is sequentially pressed but not stretched into the resulting groove.

When restoring the structure, a mandatory step is to insulate the window frame

Most often, the repair and restoration of wooden windows ends with painting. For this, it is recommended to use special compounds that are well resistant to temperature extremes and the effects of precipitation: oil paints, acrylic and alkyd enamels.

The coating must be applied in 2-3 layers

It is advisable to cover the windows with two or three layers of paint, spreading it as it ends... Optimal consistency will create an even, non-flowing layer. Initially, it is best to work with a thinner paint. You should not try to immediately close all the visible flaws on wooden windows, since the bulk of the initial layer will still be absorbed. The second layer is applied only after the first one has completely dried.

It is advisable to paint the window frame with the glasses removed. This will allow you to skip the unpleasant smudge removal procedure.... But if the glass has not been pulled out, then to protect them, you can use a special masking tape glued back to the frame.

The restoration of wooden double-glazed windows ends with the installation of glass. The procedure consists of several stages:

Squeeze out some silicone aquarium glue under the inner corners of the frame;
Insert glass and secure with studs;
Remove glue drips with a cloth soaked in vinegar;
Do not completely scrape off the silicone from the fasteners: it will protect them from rust;
After the glue has set, fix the glass with putty (chalk + drying oil) or pre-treated glazing beads.

It is necessary to properly fix the glass in the window frame

Repairing wooden windows with double-glazed windows is not a very difficult undertaking. Basic problems can be easily fixed with your own hands. A skillful combination of ancient restoration technology and modern materials can work wonders. A little patience and yesterday's shabby window will acquire a new, restored look, retaining all the useful properties of wood. Image - DIY repair of a wooden window frame

Even the highest quality synthetic material cannot replace natural wood. She is safe and attractive in appearance.Wooden windows in many apartments have been standing for many years and their owners are in no hurry to replace them with PVC frames and double-glazed windows. Why? Because wooden windows do not interfere with air exchange, thanks to this, a comfortable microclimate is maintained in the room, which not everyone is ready to give up in favor of sealed plastic. In addition, the replacement of windows involves large-scale repair work, which includes the installation of new frames and window sills, improvement of external and internal slopes, and these are large financial costs.

To save time and money, you can give new life to old windows. The wood lends itself well to repair. You can restore both appearance and functionality with your own hands.

Unfortunately, repairs are not always possible. If the window is completely unusable, then replacing it is the only solution to the problem.

In what cases will the window have to be dismantled and discarded:

The frame literally crumbles. Most often this occurs in the lower part of the window, where condensation accumulates;
The geometry of the window is badly broken. If it cannot be fixed without dismantling the box, then it is better to replace the frames;
The window is too fragile. Thin bindings between glasses may not withstand mechanical stress. Considering that it will be necessary to peel off layers of paint from the frame, which means that force is applied, then you should not waste time on restoration, but immediately dispose of the window.

You can replace the window not only with the popular plastic, but also with a wooden one. Such products cost a little more and practically do not differ functionally from PVC windows, as they are equipped with modern fittings and double-glazed windows.

What can be repaired:

The appearance of the frames;
Broken glass;
Slots;
Small distortions;
Local rotten areas;
Sagging sashes.

To carry out the repair, you will need a set of tools and materials: chisels, a plane, a spatula, a drill, a level, a sealant, a sealant, drying oil, putty and paintwork.

The restoration is best done during the summer, in warm and dry weather. You need to start with inspection and identification of defects. In order not to miss anything, the frames can be removed from the box, check the integrity and reliability of the connections, as well as compliance with the level of the sides of the box.

The most common problem faced by the owners of wooden windows is blowing through, as a result of the freezing of ice in winter.

The following defects can be the reason:

Drying of wood and the formation of gaps between the frame and the box;
Depressurization of seams and joints between glass and frame elements.

Previously, ordinary cotton wool was used to seal the cracks, but today you can purchase high-quality and easy-to-install foam and rubber seals. They have a self-adhesive base covered with a protective film or paper.

To close the cracks with seals, it is necessary to remove the frames from the boxes, and glue the contact points along the entire contour. If the gap is large, then the strip of material must be glued to the frame as well. The open sashes are glued in the same way.

The gaps between the glass and the frame can be sealed with silicone sealant. To avoid rattling the glass, it must be planted with aquarium glue.

Over time, the opening parts of the window sag under their own weight or swell after being saturated with moisture. Because of this, the sashes can be difficult to enter into the frame or stop closing altogether. There can be two ways out of the situation:

Chip off the top layers of wood;
Pull up or move stitches.

The first option is suitable if there are no gaps, and the sash fits snugly against the frame around the entire perimeter. You can visually detect an area that interferes with functionality; paint will be erased in this place on the frame. You need to cut off the wood from the sash, in thin layers, in the process, check how easily it enters the opening.

The second option is used if a gap has formed.To fix the large slack, the hinges need to be removed and set a few millimeters higher. It is also possible that the fastening of the hinges is simply loosened, in which case you can tighten or replace the self-tapping screws. If the gap is small, then you can try to wind a thin wire around the hinge rods and hang the sash.

Other reasons can also impair the functionality of the sash, for example, a skewed frame or multiple layers of paint.

This problem is one of the most serious and requires major restoration. As a result of distortions, the functions of the window are violated, cracks are formed and the appearance deteriorates.

The skew can be visually noticeable. If you can't see it outwardly, you can use a level. Even a small drop can affect the quality of the window - a 2-3 mm gap will become a source of cold air and cause ice to freeze.

The solution to the problem must be cardinal - the frames must be dismantled and returned to the correct geometry. A simple and reliable way is to attach metal amplifiers to the corners. To do this, it is necessary to make landing recesses in the frame so that the corner, after installation, does not protrude beyond the frame. The same corners can be mounted on sashes and vents. To achieve the correct geometry, the frame without glass must be laid on a flat shield and the diagonals aligned.

If the pins or "chopiks" (wooden nails at the joints of the frame parts) are loose, they can be filled with glue, before that, the diagonals must also be adjusted to equal values.

Sometimes the pins dry out and are freely removed from the groove, in this situation it is better to make new ones, of a larger diameter, and lubricate them with liquid nails before installing. To make chopiks, you need a core drill and a piece of solid wood.

Correcting the geometry of the frame is not enough, it is possible that the box is also crooked. You can change its position without dismantling, but only if the difference does not exceed 2 cm. For this, it is necessary to determine the lowest point in the lower plane of the box and the highest in the upper one. Focusing on them, cut off the "excess" in terms of level. The same should be done with the side parts of the box. To control the shape of the opening, you need to measure the diagonals, as well as the height and width at several points.

Inevitably, the frame will become smaller than the opening. To adjust the dimensions, you need to install wooden slats of appropriate thickness around the perimeter.

Moisture is the first enemy of wood. If the windows "cry" decay is inevitable. It is important to detect the defect in time so that it is possible to eliminate it without replacing the window.

For work, you will need to dismantle the frame or sash with a damaged area, remove the glass and lay the product on a flat shield. A damaged piece of wood must be chipped or cut off, and a new part must be planted in its place. It must be carefully sized and fixed with liquid nails or wood glue. Level the surface, cover with putty, sand and paint. If everything is done carefully, then there will be no trace of the defect.

Minor damage can be repaired with a putty. To do this, it must be abundantly applied to the damaged area until the lost volume is restored. The composition must be kept until completely dry and given the correct shape.

Old wooden windows, as a rule, are covered with more than one layer of paint, which has begun to peel off and has smudges. Of course, you do not need to waste a lot of time, clean up what is falling off and apply another layer, but in order for the window to look like new, the old coating must be removed completely.

Before starting work, the frames must be removed from the box, the glass must be removed and all metal elements of the mechanisms must be removed.

There are three methods for cleaning old paint:

The first is the most difficult and time consuming, but does not require special tools and materials. By hand, paint can be removed with a spatula, sandpaper or scraper.The method is not always effective, it is appropriate if there is a thick layer of paint on the frames, which can be easily removed. The work will go faster with a grinder.

A building hair dryer is required for thermal cleaning. It should be directed to a section of the frame, heated for several minutes and immediately removed with a spatula. The warm cover is easily removable, with little or no residue. Areas where the paint is held tight can be sandpaper cleaned.

During chemical cleaning, a special liquid is used to remove paint, you can also use what is at hand, for example, kerosene.

For this method, the frames must be wrapped in rags, moistened abundantly with solvent and packed in a plastic bag. Withstand a couple of days, after which you can clean the surface with a spatula from the softened paint. The wood after such treatment will not be perfectly clean; you will need to remove the remains of the coating with a grinder or sandpaper.

The next stage is puttying. This type of processing is necessary to smooth out small defects: cracks and irregularities. Before this procedure, it is recommended to remove burrs, cut off protruding parts and clean the surface of dust. The composition must be applied as thin as possible. Then dry well and sand.

Before painting, the wood must be protected from damage. Linseed oil or antiseptic can act as such a coating. The frames should be impregnated with them in several layers.

The paint can be applied after the protective coating has dried. You can check the readiness of the drying oil by touching the frame, if the hand does not stick, then the surface can be painted.

Applying fresh paint is the most important step. Much depends on the choice of material. Oil paint works best for windows. The samples presented on store shelves are made of synthetic components, their service life is short.

Natural paint is needed to keep windows looking good for 10 years. It can be prepared from a thick-grated mineral pigment-based paint mixed with linseed or walnut oil.

It is more convenient to apply the coating with a thin brush. It is better to remove the glasses so as not to accidentally get them dirty. You can put the frames back in place when the second coat of paint has dried. It can also be used to cover the drainage system, the window sill and the inner slope.

How to restore wooden window frames, including the installation of seals, removing the old coating, puttying and painting, is clearly shown in the video:

With proper care, a self-restored window will last another year and will delight you with functionality and aesthetics. Image - DIY repair of a wooden window frame

In order not to bring the source of natural light in the apartment to a deplorable state, you need to monitor the windows, namely:

Avoid the accumulation of moisture on the surface of the glass and window sill. Condensation can be caused not only by cracks in the windows, but also by flower pots, blinds and blackout curtains;
Regularly clean the window and glass from dust and dirt with soapy water and a soft cloth;
If a rubber cord is used as a seal, then it should be oiled twice a year, this will prevent drying and cracking;
The metal parts of the structure (hinges, constipations) should also be lubricated and cleaned of dust;
It is recommended to remove the paint from the frame and apply a new one every 10 years;
If the glass is sealed with putty, the seam must be changed as it deteriorates.

You can read about the repair of PVC plastic windows here.

Take your time to get rid of old wooden frames. If their basic properties and integrity are preserved, minor imperfections can be eliminated and their visual appeal restored. At the same time, the family budget will be well saved.

Before deciding on the restoration of wooden window frames, make sure that they are subject to such work.Their condition can be quickly assessed by looking for holes left by pests, cracks in the wood, threading of the frame and sash.

You should make sure that they did not decay, and most importantly, they were not distorted. You can use a chisel and hammer to do this. By lightly touching, you can check if the wood has decayed, rot or damage from pests.

you can keep your home environmentally friendly;
the rooms will always have an optimal comfortable microclimate;
wooden windows are often the main attraction of many houses, and restoration will allow using modern methods and materials to keep their appearance intact.
Significant savings on average

During the operation of wooden window structures, their owners often have to deal with the following problems:

The gap between the frame and the window frame.
Surface coating problems.
Skewed window sashes.
Decay of part of the binding or frame.
The doors close tightly.

Defect 1. The problem of insufficient tightness is one of the most pressing. Such gaps are formed due to the fact that wood is such a material that is easily deformable. In this case, the need to restore old wooden windows is explained by constant drafts.

But it is quite simple to fix this problem. You just need to install an additional seal.

Defect 2. Repair of old wooden windows will also be required if the stain or cracked paint is worn out. After a few years, paint on such structures loses its original properties, regardless of its quality and price. To restore the window, it will be enough to simply renew the painting.

Defect 3. An urgent problem, especially when it comes to solid board frames. The main reason for the skew is the properties of wood to deformation under the influence of moisture or direct sunlight. You can eliminate such distortions by adjusting the fittings. If this is not possible due to the technical features of the selected parts, you will have to change the hinges.

Defect 4. This is the most difficult defect in the tree that cannot be fixed. In case of decay, you will need to completely change the window structure.

Defect 5. Quite a common problem during the operation of old wooden windows. In order to return them the ability to close normally again, then first it is worth checking if the structure as a whole has not sat down. If so, simply adjust the height of the flaps.

In order to reduce the amount of work associated with the repair of old wooden window frames, it is necessary to periodically maintain their condition by processing with special preparations.

Sometimes, the owners do not attach importance to this, and after a few years it turns out that the windows are only suitable for replacement. Consideration should be given to whether it is possible to find hard wood under a layer of old oil paint, and with less effort and financial investment, extend the life of such structures.

Before starting repair work, the sash must be removed from the hinges and placed firmly on the prepared supports. It is worth putting, for example, foil around the window to protect neighboring objects from contamination. Ideally, they just take out the glasses.

New paint cannot be applied to old coats. It is better to remove them, but it is imperative, observing safety precautions at the workplace, because every carelessness can lead to damage to the glass.

Renovation of old wooden windows - preparatory stage

Before renovating old wooden windows, you will also need to remove the old putty or sealing material that connects the glass to the window frame. These elements are now made from materials that are more durable and aesthetic than they were a few years ago.

It is best to use acrylic.It is carefully applied to a surface free of grease and dust, preferably with a finger moistened with water. Before applying paint, care must be taken to protect the window fittings from dirt.

Please note that the clearcoat coating must be renewed every 2-5 years and the paint every 5-8 years.

The restoration of old window frames must be combined with the repair or replacement of hinges and fasteners. Correct fit will ensure the stability and tightness of the windows. The hinges are replaced with new ones or only their fasteners or bolts and screws are replaced. The hinges must be oiled or specially trained as recommended by the window manufacturer.

To properly carry out the restoration of wooden windows with your own hands, you will need the following materials and tools:

hair dryer to remove paint. This unit helps to remove the coating without damaging the surface of the frame;
sanding machine;
sandpaper;
a boot knife that easily removes old paint;
a spatula, since the repair of wooden window frames requires a compulsory putty to renew the surface of the frame and sashes;
paint brushes;
chisels;
fittings, glass (this is if you plan to change these elements);
drying oil, varnish, paint;
primer;
putty;
sealant.

It is important to pay a little more attention to the choice of filler. In total, three types of it will be needed for work:

Coarse-grained putty for window frames with wooden surfaces. It will be used to seal large cracks and other defects. The material is often used in the restoration of wooden doors.
Fine-grained finishing. Most often, the product is used to decorate the interior of the premises. But it is also great for working with wood. The only thing to keep in mind is choosing the right color. The best option is white. It is better than beige, it hides the sealed defects in the future.
Deep penetration primer. The material is necessary to achieve a better combination of paint and putty.

Renovation of old wooden windows consists of several successive steps. Let's consider them in more detail.

Step 1. Removing old paint

This can be done in three ways:

Mechanical removal of old paint layers involves the use of a thin spatula, sandpaper, and grinding machines. The need is also the use of tools that are used manually, especially in corners, bends, hard-to-reach places.

Flaky or cracked films of paint are not a good substrate for a new coat, so the first step is to remove it. The easiest way that we can do it ourselves is to remove the old coating with a spatula. This requires the use of special paint removers.

Paint removers can be found in every chemistry store. They, as a rule, are presented in the form of gel preparations, which are applied with a brush to the refurbished surface with a thickness of up to 2-3 mm.

When choosing products for removing old coatings, preference should be given to acid-free products. Otherwise, they react with wood.

The agent should remain on the surface for up to 30 minutes, depending on the number of coats of the old coating that needs to be removed. After a short interval, the product layer softens and can be easily removed with a spatula.

Another way to remove old coverings is to use a hair dryer according to certain practical tips. It allows hot air to be directed, which removes the paint. This method is mainly used to protect glass from heat. When bubbles appear on the frame, you can pick up the paint with a spatula.

Step 2. Smoothing the wood surface

What happens when there are defects? Old windows can have deep scratches, defects or even damage on the frame.Before painting, they must be filled with a special putty for wood. To apply the putty, use a special spatula with a rubber tip.

The mass is tightly packed in one layer. It should not be thicker than 4 mm. Therefore, if the cavities are larger, in some cases you will need more layers, which are applied after the previous one has cured.

Step 3. Sanding the surface

The next step is to get a smooth surface for painting. Sandpaper is used to sand the surface.

When the surface is smooth, it is thoroughly cleaned of dust, washed out and left to dry completely.

Step 4. Impregnation with linseed oil

This is a fairly old method, but very effective. Despite the fact that today it is very difficult to find natural drying oil on the building materials market, the technology is still relevant.

Manufacturers offer the product from various synthetic derivatives, rather than from hemp and linseed oil, as in the old days. Drying oil was replaced by impregnation of good quality, the production of which is much more profitable.

To cover the surface of a wooden window structure, you will need a special paintbrush. The first layer is laid down as an impregnation, and the next two are final. Make sure the surface is not sticky before proceeding.

Step 5. Painting

What paint to paint the window frames? In order to preserve the grain of the wood, varnish should be used. It is available in many colors, natural wood, and the surface gives a delicate shine.

But for repairing window frames, the best coating is still paint, which will mask irregularities. Wood emulsions are available in many colors.

It is worth remembering that the paint should cover about 1 mm of the glass. Thus, a protective layer is formed to prevent the penetration of water between the glass and the putty.

If maintenance is carried out correctly and regularly, this has a positive effect on the condition and significantly prolongs the service life and durability of the preserved object. This includes cars, clothing, TVs and windows.

Regular care of the condition and cleanliness of the window, taking care of correctly selected protective measures will significantly extend their service life.

Modern wooden windows at the manufacturer's factories are treated with means that protect them from the harmful effects of external factors (sun, rain, air pollution). Repair of wooden euro-windows, or rather paint and varnish, is recommended every 3-5 years - depending on the type of coating used (paint or varnish).

Cleaning and maintaining the window frame requires appropriate measures. The wood is best washed with diluted liquid mild dishwashing detergent.

Therefore, you should keep in mind that you should not spray the same products on window frames and glass when cleaning glass. Any residue, even the smallest, must be removed from the frame - rinse with water and wipe dry.

In order to extend the life of the paint and maintain its aesthetic appeal for a longer time, it is good to additionally use various care products after washing the frame. They are applied to the cleaned and dried frame using a soft cloth or cotton wool. It is not recommended to use such products in bright sunlight or on hot surfaces. The optimum temperature is 10-25 ° C.

The coating mill should be checked regularly - at least twice a year (in spring and autumn), taking into account the external condition of the frame surface.

Despite the fact that modern manufacturers of wooden window structures are trying to protect their products as much as possible, after a month of operation without a protective paintwork, the frame begins to absorb moisture from the environment

Wooden windows are products that must be constantly taken care of in order to maintain their attractiveness.

If you do not follow the advice of experts and do not take care of the condition of such windows, then repairs can be expensive. It is always best to do minor repairs to avoid trouble on a larger scale.