DIY jack repair

In detail: do-it-yourself repair of jacks from a real master for the site my.housecope.com.

In order to repair the hydraulic jack as little as possible, you need to monitor the product and operate it correctly. Maintain the correct level of fluid that seeps through the seals. Often, due to the ingress of air, the load is jammed while it is being lifted. Then difficulties arise when it is lowered. In these cases, the jack needs to be disassembled and repaired. Carry out it really on your own, observing a certain sequence of actions.

The hydraulic jack consists of 3 parts:

At the beginning of operation, the mechanism is placed on a flat surface, the valve closes and, due to the movement of the lever, the stem is lifted. On descent, the valve opens and the pressure of the weight returns the stem to its place.

When the lever is pressed, fluid is pumped from the housing into the cylinder, pushing it up. The suction and discharge valves prevent it from returning.

When the valve in the pump opens, the fluid returns to the housing space.

Bottle jacks have the ability to lift loads ranging from 3 to 200 tons. This is ensured by the presence of a large support plane.

There are 2 types of bottle machines:

Single-stem. Due to their ease of use, they are used in mechanical engineering and construction. The jack is adopted by motorists - for lifting cars. Used as a knot in a pipe bender or press.
Double-headed. Works both vertically and horizontally. The device includes 2 rods. They are lifted up by a cylinder.

Externally, it is a cart mounted on wheels. Before work, it rolls up under the load being lifted.

Video (click to play).

The design is large in size, so it is used in tire shops. Lifting is done by pressing the lever. When the valve is opened, the stem is lowered.

If a slight lowering is required, a tubular handle is used. It fits onto the valve screw and rotates it around its axis. A slight decrease in the stock begins.

This type of product has disadvantages:

Large dimensions and heavy weight of the product.
The presence of a concrete or asphalt site.

Do-it-yourself repair of a hydraulic jack. For this, all possible malfunctions and the rules for their elimination are studied. Parts are prepared in advance - to replace those that have failed. The main causes of breakdowns and the rules for their elimination are known. To do this, you need to have a suitable tool at hand.

If the hydraulic cylinder fails, the oil reservoir must be removed. The piston is disconnected first. To do this, use wrenches to unscrew the screws located at the top. The protective rings are removed, the reservoir is pulled out. If the cylinder is damaged, then it is replaced. During the installation process, you will need a clamp. The bolts unscrewed from the jack are replaced with new ones. They come in the same size. If the removed bushings are worn out, replace them. Some models allow the use of the round type.In the event of the upper ring protruding, the upper plate is disconnected. It is preliminarily examined for defects. The screws are unscrewed using keys. It is important to inspect the piston to make sure that the broken ring does not damage it. After that, engage in installing a new one on the stock. In order to improve fixation, use a seal.If there is a flyout of the lower ring, then the lower frame is removed.In this case, the hydraulic cylinder is inspected. Its integrity is checked. It is important that the piston moves smoothly without jamming.To remove the frame, the jack is turned over and securely fixed. The cover is removed only after inspecting the O-ring. Using a screwdriver, the retractable extension is removed. It also requires inspection, since there is a risk of damage from the ring.In the event of its replacement, the marking is specified, which is stamped on the body or recorded in the documentation.During installation, the stem is lubricated with machine oil. A new ring is also being installed.

Before filling with new oil, the old one is completely removed. If flushing liquid is present, it is also removed.

Before filling in a new one, all the air present is eliminated. The outlet valve opens and the device goes down. Then you should carry out at least 5 pumping. The bolt is removed from the filler neck and oil is poured through the nozzle to the required level. Then the pumping is repeated, and the oil is poured again. It is important to bleed all air from the system. As soon as the oil surface stops bubbling and reaches the desired mark, the jack is ready for use.

If the jack is properly operated, the number of breakdowns will dramatically decrease.

To do this, you need to adhere to the following rules:

It is forbidden to lift a load exceeding the permissible one.
The work is carried out smoothly, without jerking.
Installation can only be carried out on a flat surface.
Before work, all movable joints are lubricated.
An external examination of the device is carried out in order to detect cracks or oil leaks.
The oil level is checked and must be brought up to normal.

A monthly maintenance is required to keep the hydraulic jack running smoothly. Since the product is constantly subjected to heavy loads, all parts require the presence of lubricant. It is important to avoid the presence of dirt, which leads to jamming of the apparatus. The device is stored in a lowered state.

The use of a glue gun, design and principle of operation. Step-by-step instructions for gluing surfaces. Replacing the used rod. Safety regulations for work. Possible malfunctions and their elimination. Features of work with one rod in the absence of a pistol.

Do-it-yourself air conditioner installation. Description of the device and the principle of operation of the air conditioner. Detailed instructions for installing the device: installation of outdoor and indoor units, laying pipes and wiring.

Lifting a house with a jack with your own hands, step by step instructions. Possible errors during work and lifting technology. Useful video on the topic.

The jack is quite widespread. They are in the arsenal of almost every car enthusiast; they can be useful when carrying out various work in the workshop. There are several types of such a mechanism, in this case we will pay attention to the hydraulic one. Such a tool transmits force by compressing the fluid. The complexity of the mechanism and its application in difficult operating conditions determines the need for repairs. You can repair the hydraulic structure with your own hands, but all the features of this process should be taken into account. Consider how to repair a hydraulic jack and what the features of this process may be.

Repair of a hydraulic jack

The design of a hydraulic jack can vary significantly. Many professional models can last for a long period, but still certain reasons can lead to a serious defect.

Hydraulic trolley jack

Faults in the hydraulic jack can be attributed to the following problems:

Many causes of hoist failure are the result of improper use of the device. In addition, some hydraulic jack models require periodic oil changes. These and many other points are taken into account when reviewing the operating instructions.Do-it-yourself repair of a hydraulic jack can be done in your own workshop if you have the required materials and tools. It should be borne in mind that some versions of the lifting mechanism are represented by non-separable structures, and it will be rather difficult to carry out repair work. The hydraulic jack should be disassembled taking into account the peculiarities of its design. This may require the following tools:

Hammer and chisel.

Pliers.

Screwdrivers with different diameters.

Hacksaw.

A set of keys and a gas wrench.

Necessary repair tools

There are just a huge number of varieties of hydraulic jacks, so it's difficult to say exactly which tools you may need to get the job done. In some cases, it is possible to easily access the internal mechanism for maintenance or repair, in others it will take quite a lot of free time to sort it out.

As for the materials, it all depends on what kind of malfunction in the structure. very often seals that are made of plastic or rubber fail. Quite a lot of difficulties can arise with their selection, since even a small gap can lead to the passage of the working fluid into the upper chamber (leading to a drop in pressure). If we consider damage to the rod or glass, then such malfunctions are solved only by replacing the entire element.

When considering how to disassemble a hydraulic jack, consideration must be given to design features. The force in all cases is transmitted through oil, which has a low compression ratio. As previously noted, the oil should be changed in order to ensure the long service life of the device under conditions of frequent use, as it can lose its performance over time.

Hydraulic jack device

The device of a rolling jack does not differ significantly from the usual persistent one. The working part is done using similar principles. It should be borne in mind that the design largely depends on what the carrying capacity is. Some models are equipped with a threaded extension that allows the initial lifting height to be initially adjusted.

A hydraulic jack with your own hands can be repaired in the event of a malfunction of the auxiliary elements or the main working part. In most cases, problems arise precisely with the working part. The classic version is represented by a combination of the following elements:

A piston that has O-rings. It is on him that the pressure is exerted by the liquid. Due to the combination of a huge number of seals made of different materials, the piston does not allow oil to pass through, even when high pressure occurs. In addition, the structure itself is designed for high loads. The use of rubber seals allows the element to be movable.
Cylinder with seals. It is the cylinder that creates the working cavity in which pressure is exerted on the rod. In order to reduce friction during the stroke of the moving element, the surface is polished to a mirror-like state. In the manufacture of this element, materials with high corrosive properties are used. The appearance of even insignificant rust leads to the fact that the moving part begins to wear out quickly. The outside of the cylinder is cast iron, which is highly susceptible to shock loading. Therefore, you should handle the tool in question carefully.
Power rod. This element is connected to the piston and is set in motion. It is the rod that perceives the load that occurs between the lifted object and the piston. High-quality steel is used in the manufacture, designed for high load. To extend its service life, the surface is chemically treated to provide corrosion resistance.It should be borne in mind that when using a hydraulic jack in violation of operating recommendations related to permissible loads, the rod is curved. Such a malfunction is extremely common.
Passage channel systems. In order to supply and remove oil from the working chamber, passageways are required. They are small and can become clogged over time.
A plunger pump that provides pressure. Most of the mechanical-type devices provide for manual pumping of liquid into the working area. The plunger pump device is characterized by high reliability, rarely fails.
A bleed valve is used to remove liquid from the working chamber. Such a structural element can be implemented in different ways. As a rule, this is a small screw, when turned, due to the pressure exerted on the rod, all the liquid is removed from the working chamber.
Cuffs and seals. These elements provide insulation for the working chamber and other structural elements. They also provide mobility of the piston rod. In the manufacture of cuffs and seals, plastic materials are used that are highly resistant to mechanical stress or the effect of the oil used. Important indicators of seals are their outer and bore diameters, as well as rigidity and wear resistance. Finding a suitable replacement option is in many cases quite difficult.
Filler hole to maintain the required oil level in the system. From time to time it is necessary to add oil to maintain the required level. As a rule, when the hydraulic jack is used intensively or when it is transported in the wrong position, the hydraulic fluid level drops. Some device models have an oil level indicator.

Read also: DIY repair of grinders

Rolling jack device

In general, we can say that the design is quite simple, but it has many rubbing elements. Many manufacturers create collapsible designs when the seals on the stem are fixed with a nut or other fastener. It should be borne in mind that there are also non-collapsible versions, the repair of which is several times more complicated.

Repairing a jack in most cases is quite simple, provided you have the necessary consumables. It should be borne in mind that the appearance of corrosion on the surface can significantly complicate the task. Therefore, you need to purchase a special liquid for removing corrosion and oxidation.

Do-it-yourself repair of a sliding hydraulic jack can be conditionally divided into several main stages:

The essence of the problem is determined. If the structure does not hold pressure, then there is a high probability of wear on the seals. In the case when the lift occurs with difficulty, that is, the possibility of deformation of the stem or the occurrence of other problems.
A complete analysis of the structure is carried out. At this stage, the main thing is not to damage the fasteners. It is worth remembering that during the supply of pressure, the working cavity must contain it. Even a minor defect can cause leakage and pressure drop.
Inspection of the integrity of the main elements is carried out. In most cases, the cause of the problem can be determined by visual inspection of the structure. For example, seals can have grooves, grooves and other deformations, a slight bend in the stem, low flow channels due to the accumulation of soot and dirt.
After determining the cause of the malfunction, you can repair the rolling jack.

In most cases, the hydraulic jack can be repaired as follows:

After disassembling the structure, the internal cavity is cleaned from various debris. In addition, the oil used will have to be completely replaced.

The seals can be removed in various ways. As a rule, there is a fixing element, due to which the immobility of the elastic bands is ensured during the operation of the device. It is worth considering the sequence of the arrangement of rubber bands and seals of various types. Incorrect installation may result in the device not holding pressure.

As previously noted, stem curvature and damage to the mirror surface cannot be corrected on your own. Too much wear and tear leads to the fact that it is necessary to replace the entire element or the lifting mechanism itself.The bottle-type hydraulic jack has an even simpler design. As a rule, it does not require any adjustments. Therefore, after assembling it, you can start testing and subsequent operation, provided there are no problems. Some manufacturers of lifting mechanisms provide instructions on how to disassemble the device and carry out repairs. Its use can significantly simplify the task. Image - DIY repair of jacks

The repaired hydraulic jack must first be checked for proper operation. This is due to the fact that frequent use with improper installation of seals or other mistakes will lead to rapid wear of the main elements. Therefore, you should provide for the presence of insurance in the event of lifting the car or other mechanisms. With the correct repair work, you can significantly extend the life of the hydraulic jack.

If you find an error, please select a piece of text and press Ctrl + Enter.

A jack is a special device with which a heavy load is lifted and fixed at the required height. This mechanism is simply irreplaceable when performing any car repair, for example, when changing a wheel.

Trolley hydraulic jack.

The most convenient and effective for work are hydraulic jacks, the working force of which is achieved using hydraulic oil and a piston. Assembly and repair of such a device can be done by hand.

The rolling jack belongs to the category of hydraulic ones, only it has a slightly different design. On its body, made of metal, two pairs of wheels are installed. In the holes located on it, a lifting mechanism and a hydraulic cylinder are mounted, which, when extended in the horizontal direction, lifts the platform. The device itself gradually raises the car to the desired height, while it rolls under it.

The jack is set in motion by swinging the lever and lowered by turning the valve screw. During the process of lowering the load, a tubular handle is pushed onto the valve screw, and after that the baffle enters its groove. When the handle rotates around its axis, the screw itself rotates accordingly. In this case, the pressure in the working cylinder is released, and the load is lowered to the desired height.

In order for the jack to serve for a long time, it is necessary to monitor the presence of oil in it and the condition of the oil seal and valves.

There are sliding hydraulic jacks used for personal purposes for vehicles with a weight category up to 3000 kg. Most often, such a device, equipped with the pedals necessary for preliminary lifting, is used in car services and tire stations. It can lift loads up to 4000 kg, doing the job quickly enough.

Jacks, which lift loads up to 20 tons and are equipped with pre-lifting pedals, as well as a sliding traverse, are designed to serve heavy machines and special vehicles. This mechanism also has its drawbacks, which include volumetric size and heavy weight, which makes it difficult to move it in a car.It requires a flat, horizontal surface such as asphalt or concrete to work.

wrench;
container for draining oil;
kerosene;
butter.

During the operation of the jack, its breakage may occur. The malfunctions of this device include oil leakage, jamming when lifting to a height, or, conversely, its refusal to descend. In any case, it should be repaired.

If the cause of the breakdown is oil leakage, then first you need to disassemble the device. Then the pistons are removed from it and checked for corrosion. After that, all dirt and the resulting corrosion are carefully removed. Next, the stock is checked. In the event that it is bent and deformed, the repair of the jack can be considered impractical.

The principle of operation of a hydraulic rolling jack.

When repairing a valve that allows oil to pass through, you need to unscrew it and check if dirt has got inside and if it has been deformed. In the event that it has undergone mechanical deformation, the valve should be replaced. If it gets dirty, then the working fluid will flow due to the fact that the ball has ceased to sit tightly in the seat. Therefore, first, the old working fluid (oil) is drained into the prepared container, while pumping the system with the lever, raising and lowering it.

Then all parts are thoroughly rinsed from trapped dirt, as well as from the remnants of old oil. In this case, it is imperative to replace all the cuffs, as well as the gaskets. If the dirt gets directly into the working cavity, then to remove it, you will need to unscrew the head of the case.

After that, kerosene is poured into its base, and the jack is pumped. In this case, the shut-off needle must be unscrewed. At the end, the kerosene is removed, and a clean working fluid is poured into the working cavity.

The efficiency of the jack may decrease due to the accumulation of air bubbles in its working cavity, which get there due to a lack of oil.

Repair in this case is carried out as follows. First you need to open the plug at the oil tank and the bypass valve. Then, at a fast pace, the pump of the hydraulic press is pumped several times in order for the air from the working cavity to move into the container in which the oil is located. The oil tank opening and the bypass valve are then closed. If the whole process is done correctly, the jack will start working normally. With the remaining air in it, all actions are repeated again.If this device does not work or raises the load very slowly, then air can be removed from the working cavity in another way. To do this, the shut-off needle is turned one and a half or two turns. Then, with the help of a hand, the plunger rises by the screw, reaching the extreme upper point.

Like any equipment that carries huge loads, devices can often break down, and therefore you always need to know how to repair the jack yourself. To be fully armed at the time of a breakdown!

Any hydraulic jack operates on liquid, and the main elements of the jack are the body, piston and oil.If you decide to study how to carry out repairs yourself, you definitely need to know what reasons can lead to breakdowns. First of all, the structure of the device could be "attacked" by corrosion, which leads to restriction during the descent of the mechanism. Naturally, jacks often break due to too much stress, which leads to bending of the rods. Image - DIY repair of jacks

There are some other points, including the need to change the oil. However, any repair is carried out practically according to the same scheme. And the first thing you need to know is how to disassemble the device, after which you can start changing the fluid. The tool is disassembled in the following order:

Using wrenches, unscrew the fasteners;
Remove the fluid bleed valve and piston;
Carrying out a competent inspection, we check the quality of the valve and all gaskets - if you notice that they have become unusable, we just change the elements of the jack;
We clean the mechanism from debris and other foreign elements, rinse the cylinder;
We check and replace the old rubber band if necessary;
The last step is to reassemble the tool in reverse order.

Naturally, after you assemble the jack, it should be checked for operability! If the device starts working, great, but it doesn't always work out the first time. Perhaps the oil is the problem?

Oil is the driving force of the device, it is this oil that presses on the piston, setting the rod to the desired position. Due to this, it is possible to lift almost any load. If there is not enough oil in the device, the mechanism will not work. Many who start repairs for the first time miss this moment, which ultimately leads to problems with the operation of the jack. Oil change instructions:

In order to fill the jack with oil, you must first unscrew the plug and drain the old fluid. The next step is to clean the mechanism with flushing fluid, which can be purchased at any hardware store. By the way, it is quite difficult to flush the jack completely, especially for a beginner, because you will have to fill in the liquid at least two or three times, after which the pumping is carried out, the liquid is added again and pumped again. The old oil is drained in the same way - so that not even a drop of old fluid remains inside the mechanism.

The container must be filled with oil to the end, that is, until the liquid reaches the required level. In this case, set the jack in a low position. To lower the stem to the lower position, be sure to turn the screw-cock until it reaches the “drain” position. Having tightened the plug, we carry out the pumping for five times, after which we add oil and tighten the plug again. There will not be enough oil every time during the cleaning process, and therefore it is necessary to pump it until the “fuel” of our jack reaches the required level, and bubbles stop appearing on the surface of the liquid.

As you have seen, repairing jacks with your own hands is a fairly simple job. However, of course, I do not want to bring it to repair work, because it takes both time and effort to implement. That is why we have compiled a selection of recommendations from experts for you. If you follow them, the operation of your jack will become much easier, and repairs can be "pushed" further away. Image - DIY repair of jacks

In order for the oil change work to be carried out efficiently and correctly, it is imperative to remove any loads, and the device itself can be started to operate only after you have completely completed all the work and assemble the jack;
It is advisable to change the "fuel" twice a year, and if you use the jack constantly, then at least once a month you need to carry out these works, and you must flush the entire mechanism every time;
You can choose any oil, but if you are going to use the device in the winter season, be sure to use a synthetic solution. This will allow the mechanism to always be in "full combat readiness" for work;
No matter what time of year it is outside, it will be better if you can store the tool in a dry and warm place, otherwise the oil may simply freeze;
If it is necessary to carry out work in the winter season, remember that too long work in the cold can lead to damage to the device, and therefore the operation of the jack is possible in the most extreme cases and for a short time.

If you work with these methods, you can significantly extend the life of the jack. And expensive repairs, which can cost you a significant amount, can be "postponed" indefinitely, which is good news!

Today, it is impossible to imagine carrying out a car repair, whether it be changing a wheel or repairing a suspension, without using jacks - special devices that are designed to lift a load and fix it at a certain height. And today, the most popular are hydraulic jacks, in which the force is created using a piston and a working fluid.

The main elements in the design of a hydraulic jack are:

metal case;
hydraulic piston;
working fluid.

The hydraulic jack can have a regular body or an extended body made of hardened metal. The body performs the following functions: it is a reservoir for working oil and acts as a guide cylinder for the piston.

This type of unit is equipped with an air, foot or hand operated hydraulic pump. The design of the jack contains safety valves and other devices to maintain trouble-free and long-term operation.

Retractable hydraulic cylinder and lifting mechanism, which raises a special platform, are located in the holes of the case. Lowering is done by turning the T-handle. The design has built-in wheels that provide the device with mobility. The extended body of the shooting gallery is usually used to work with heavy vehicles and buses.

Any hydraulic lifting mechanism works using a fluid on the principle of communicating vessels. Before work, you need to install the unit on a solid and level surface under the machine and, with the valve closed, hold down the lever until the car reaches the required height. The descent of the machine occurs by opening the valve located on the jack body.

Working hydraulic oil pumped by the drive pump using a lever. The fluid moves into the cylinder through the valve, squeezing it out. The oil return outlet is prevented by two valves - suction and discharge. In order to lower the jack, you need to open the valve on the pump, in this case, the liquid from the cylinder goes back into the housing.

The presence of threads on the body, protected by a special casing, threaded holes in the base and threads on the stem, guarantees unlimited work of the jacks and the possibility of using it for bending, clamping and crimping. A reliable support made of hardened metal and mounted on the stem protects the hoist from damage. The grooved part of the base prevents the vehicle from slipping.

Hydraulic jacks considered the most unpretentious... The main feature of hydraulics is an incompressible working fluid. As a result, the load is lifted smoothly, braking accuracy and fixation at the required height. Hydraulic jacks have excellent efficiency - up to 85% and a large lifting capacity - over 250 tons with low effort, thanks to the high gear ratio between the surfaces of the cylinder and the pump plunger.

But hydraulic hoists have a much higher initial lift than mechanical hoists. Another difficulty is the impossibility of precise adjustment of the lowering height. To support the jack in the working position, it is necessary to constantly monitor the tightness of the oil seals and valves, as well as monitor the oil level. Store and transport these units only in an upright state, otherwise liquid may spill out of the case.

Disadvantages of hydraulic jacks:

They are rather slow.
They are large and heavy.
High price.
Small travel for single piston jacks.

The construction of the hydraulic vertical jack is the simplest. The area of use of these jacks is quite extensive due to the significant range of the lifted load - from 3 to 200 tons. Bottle jacks are used in trucks. In addition to the main advantages of a hydraulic jack, bottle models have several more - a large support area, compactness and versatility of use.

Vertical jacks can be double-stem and single-stem. The single-stem device is characterized by ease of use and simplicity of design, which expands the scope of its use and makes it possible to perform work of varying complexity:

dismantling and installation in construction and mechanical engineering;
repair of wheels of cars and cars;
use as a power unit of a pipe cutter, pipe bender, press and similar tool.

The double-rod telescopic jack has a similar structure with the vertical one, the principle of the bottle mechanism is based on the installation of several rods. The piston is located at the base of the telescopic device. It can be used vertically and horizontally. It fits most cars and has a small size. Lifting takes place using a lifting lever, which is brought into the working position by a cylinder.

This type of jack works on the same principle as a vertical one, but with the difference that the cylinder is not in a vertical position, while the piston is not directly aligned with the pickup. This device is called trolley because it is a cart on wheels that can be rolled over the surface. The jack moves while lifting the lever and picking up or "Rolls up" under the load.

This jack is set in motion, like bottle machines, by swinging the lever, it is also lowered by unscrewing the valve screw. If it is necessary to lower the weight, then it is necessary to put the tubular handle on the valve screw, then the partition enters the groove of this screw. Turning the handle around the axis, the operator rotates the screw, thus reducing the pressure in the cylinder and lowering the car to the desired height.

As a rule, a rolling jack is used at a tire changer, as it is ideal for lifting one side of a car, it is quite quick to install and work. The disadvantages of this design stem from the name - for the trolley hoist to operate, a firm and level surface, asphalt or concrete, is required. In addition, the large weight and size make it difficult to transport the device in a car.

Rolling jacks are divided by purpose:

For personal use of passenger cars with a carrying capacity of up to three tons.
For tire and automotive services, with a lifting capacity of up to four tons and with the installation of pre-lift arms to quickly reach the required lift height.
For special vehicles and the maintenance of heavy vehicles with a lifting capacity of up to twenty tons and with the installation of pre-lift levers.

Hydraulic lifting devices need periodic maintenance, therefore, oil must be added to the working cylinder, which flows out during operation through all kinds of seals and oil seals.In addition to the question of how to pump a hydraulic jack with your own hands, problems can also consist in jamming while lifting the car to the required height, as well as the inability to lift even a light load or the inability to lower the piston after lifting.

To test or repair the jack with your own hands, you must purchase the required repair kit... Before repairing, you must first disassemble the unit. To do this, you may need a key extension to get more leverage and more force. Also, be sure to prepare a container for used oil and prepare a new one.

Then you need to get the pistons and check them for corrosion. All corrosion and dirt must be removed. Make sure the stem is not bent. If the deformation still occurs, then it is unlikely that you will be able to align it again, so you can finish the repair with your own hands on this.

It is also worth checking the valve that transfers the oil. Why it is unscrewed and checked for dirt or deformation. If the valve is broken due to mechanical deformation, then it simply needs to be replaced. In this case, it can simply clog up, and the ball begins to sit loosely in its place. This is the reason for the oil leak.

Pour out the old working fluid completely. This is a fairly simple procedure, although it will take you a long time as the liquid flows through the cylinders. The oil is drained by bleeding the system by moving the lever up and down. Thoroughly wash all elements from oil and dust residues. Fully replace all seals and cuffs.

Another reason for jack breakage is dirt that gets into the working mechanism. To remove it, you need to unscrew the head of the case, pour kerosene into the base and pump the jack with the locking needle unscrewed. At the end of the operation, kerosene must be removed and new oil must be poured into the working part.

During prolonged operation, air bubbles accumulate in the working part of the jack, significantly reducing its operation. The repair of this breakdown occurs in this way.

First unscrew the bypass valve and the oil tank cap, and then at a fast pace pump the pump several times... Thus, the air will escape from the working part into the oil tank. After that, you can close the hole that leads to the oil tank and the bypass valve. If everything is done correctly, the air will escape, and the device will work normally again. If the attempt is unsuccessful, repeat these steps.

So, you got acquainted with the device of a hydraulic jack, studied its advantages and disadvantages, figured out the classification and know how to repair a hydraulic jack with your own hands. The main thing is to remember during its operation about periodic filling of working fluid and maintenance.

Video (click to play).