DIY ardo oven repair

In detail: do-it-yourself ardo oven repair from a real master for the site my.housecope.com.

We continue to consider gas stove and electric ignition... I was sure that I would not return to electric ignition. No, there are a few practical issues that need to be raised. We produce repair electric ignition. Gas stove "ARDO", electric ignition does not work.

There is a pulsed high-voltage transformer on this plate, when the button is pressed, the capacitor is charged, when released, it is discharged through the primary winding of the transformer, a spark jumps through the spark gaps, the gas is ignited. Read more about the operation of electric ignition in the article “Gas stove. Electric ignition work. "

Today we will consider only the repair of this model. Whom it does not concern, it may not waste time, However, in the course of the article, there may be positions that are interesting for you. Repairing the slab is complicated by an inconvenient approach and a non-standard solution to the issue of fixing the desktop. To dismantle the table,

remove the front panel of the stove. The front panel is fixed with two self-tapping screws from below, two screws hold the gas taps and remove it downwards. We move inward two latches, freeing the fastening of the front of the table, unscrew the four self-tapping screws on the back of the plate, and eight self-tapping screws on the burners.

The desktop can be removed. Now the approach is free. 1) We check the operation of the ignition button. - In the initial state, the following should ring out: a) The first (conditionally) leg of the plug and contact “P” on the high-voltage transformer. b) Contacts “2” and “MP”. In the pressed state: - a) The first (conditionally) leg of the plug and contact “P” on the high-voltage transformer. b) The second (conditionally) leg of the plug and the “MP” contact. (Attention! On some HEPHEST plates there may be a button, when pressed, the second leg of the plug and the “MP” contact are closed for a short time). This is good, there is less chance of burning the transformer. However, if you hold the button down for a long time, the spark will be weak or not at all. (capacitor self-discharge). 2) If, when releasing a serviceable button, no clicks are heard, we change the high-voltage transformer.

Video (click to play).

You can try to repair the transformer yourself. We remove the transformer cover, using the diagram from the specified article, determine the faulty element and change it.

This is usually a 3.8k resistor. power 1W. 3) If there are clicks, the gas does not ignite (a spark jumps somewhere from the side or bottom), we change the faulty spark plugs (spark gaps).

In the described stove, the high-voltage transformer and one candle were replaced.

The transformer failed (resistance burned out) as the hostess kept the ignition button pressed for a long time. At one time they did not explain to her that this button is pressed for a short time, and the ignition goes on after it is released. The candle was damaged from diligent cleaning of the stove. When removing and installing the burner, break off a piece of porcelain. The stove is assembled in the reverse order.

Hope you found something interesting. If you are repairing a stove, let it show you help... Now let's create a festive mood for ourselves by preparing something unusual. The computer advises you: Let's bring some excitement into our life. Make a bet! Click on the word "recipe" or "recipe" or "recipe". Who has won?

This is how employees of the gas service connected my gas stove. They assured me that it is more reliable than connecting with a special gas hose, which I bought at a gas equipment store.

Repair the gas stove is finished, we check its work. The article has come to an end. You can ask me questions using the "Feedback" form posted on the page of the same name. Leave your opinions in the comments.I visit all the sites that I meet in the comments. Invite to visit!

Modern ovens break down quite rarely, but problems in their work are not excluded. The difficulty is that the structure and all its elements do not provide for outside interference. Repairing ovens at home is usually done by replacing components and is carried out in most cases by an experienced craftsman. However, in some cases, breakdowns can be repaired by yourself.

If you decide to try to repair the oven with your own hands, then it is worth knowing the situations when this should not be done. There is definitely no need to open the case if:

the electric oven is under warranty;
the oven information panel shows that the problem is a complex component breakage;
you know nothing about electrical engineering.

During the warranty period, all repairs are made is free... Except in the following cases:

There are traces of attempts to open the structure - worn out or damaged heads of bolts, self-tapping screws, removed seals.
Insects or rodents have entered the oven, causing a short circuit or mechanical damage to components and wires.
The connection was made incorrectly, without following the manufacturer's recommendations.
Damage to electronic components occurred due to a change in voltage parameters, as a result of which it went beyond the critical limits specified by the manufacturer.

Read also: DIY hair dryer repair

In all cases where the warranty is canceled, repairs will have to be paid in full... The same situation occurs when the warranty period expires.

Before grabbing a multimeter, putting on gloves, and pulling out a set of screwdrivers, it makes sense to check the power supply to the oven. It is worth looking for answers to the following questions:

Is food served?
Is the power cable OK?
Is there good contact between socket and plug?
Are there traces of carbon deposits, melting on the plug and socket?
Is the fuse for the plug or oven broken?
Is the power wire in perfect condition, is there any fractures, scuffs or melting on it?

Checking the fuse in the plug

If the above problems do not exist, and the oven still does not start, it is worth checking the device for standard faults.

Consider typical malfunctions, methods for diagnosing them and the necessary repair of electric ovens at home. As mentioned above, most of the troubleshooting work involves replacing assemblies and parts.

If the electronic control unit of the oven suddenly fails, then be prepared to pay a tidy sum for repairs. In most cases, you do not need to do anything to identify this problem. Modern oven models are equipped with self-test system: The electronics will send a signal by itself by displaying an error code.

Do-it-yourself repair of the control module is possible only if you have experience and knowledge in electronic technology.

The parts are replaceable and can be ordered from the manufacturer's catalog. For users who prefer to get a baked chicken out of the oven, rather than electronic boards, it is better to call a qualified technician.

If this is not possible, or the qualifications of the service personnel do not inspire confidence, you can order a control unit wholly... This can be done on the manufacturer's official website or in a specialized online store. It is usually not difficult to install a board in place of a burned-out one.

Most modern models equipped with mechanical regulators do not provide for disassembly and cleaning. Primary repair consists in removing contamination from the outside, removing contact leads and cleaning the terminal plates on the regulator or timer. If this does not help or does not help fully, the part should be replaced.

Some older models allow cleaning of mechanical regulators, after which the latter work perfectly, without any complaints. It is necessary to carry out maintenance using non-aggressive solvents, for example, white spirit or a weak solution of ammonia. It is necessary to clean off oxides from contact groups with a very fine sandpaper; to eliminate traces of corrosion, special primers are used.

Oven mode switch

This is a part that is often changed, including when the gas ovens are being repaired. No interference in the design of the device is provided. The entire element is replaced.

Air blower and grill fans no longer create a good air flow over time. If the engine is running, the impeller should be cleaned. Dust constantly accumulates on it, while grease and oil are on the blowing fans.After a certain period of operation, it is imperative to disassemble the oven and lubricate the engine, if this is provided for by its design.In the event of a blower failure, rewinding or other repairs are simply unprofitable - the entire unit is replaced. Do the same with the grill motor. It is housed in a non-separable housing together with a gearbox.The heating elements of the oven are constantly working in critical mode. Determining whether the heating element works is quite simple. To do this, turn on the oven to the appropriate heating mode and check the temperature by touching your hand in a kitchen mitten. The method works, however, for a more accurate result, it is better apply a pyrometer... The device will clearly show the uniformity of heating over the area, indicate the maximum temperature in a given mode. This will make it possible to diagnose the "burnt" heating element not only completely, but also partially.Heaters are replaced after disassembling the case; it is not difficult to buy the corresponding part. The specific marking can be found after removing the heating element or according to the reference data of your electric oven model.The last three elements that change without hesitation or hesitation are the backlight, thermal fuses, and a touchscreen film panel. All of these parts cannot be cleaned or repaired.The oven electronics will inform about the operation of the thermal fuse in emergency mode, and problems in the operation of the film touch panel are diagnosed by the lack of reaction, the need to exert excess pressure, and accidental operations. The backlight lamp can be replaced independently, but to install new thermal fuses or a film sensor, it is better to contact the master.

The following elements are located under the slab top:

Hotplates. As a rule, they are bolted to the stove, and each burner consists of a divider, a cover, an injector. A copper or steel tube is suitable for each of them. To remove the hotplate, you need a 13 key.

Important! The main thing is not to rip off the head or thread during cleaning. It is better to check the tightness of the assembly with a soapy solution. It is necessary to apply foam to the nodes, test the part.

Candles. They are located around the perimeter of each burner: one is used for ignition, the other is a thermocouple, that is, an included combustion control circuit. It is quite easy to distinguish them from each other. The high-voltage spark plug is covered with a ceramic caftan.
Collector. This is a thick tube from which the wiring runs directly to each burner. The gas supply is controlled by a solenoid valve. Their number corresponds to the number of cooking zones. If the flame of one of them dies out, then the rest will still burn.
Distribution reinforcement plate. Single high-voltage wires run to each ignition electrode.

Important! If the hob is not grounded, there is a risk of electric shock.

Thyristor, capacitor, diode, fuses. These parts are present inside the cooker if the charge is generated by means of an electronic circuit. It is powered by a capacitor charge and starts to work from a surge of energy from a candle.

Important! If one of the parts listed in the last paragraph burns out, then it is easy to replace them yourself.

Let's figure out how to fix a gas stove if, for example, the burner began to burn weakly. By the way, this is the most common problem with such devices: gradually the flame begins to partially disappear due to clogging of the diffusers or burner nozzles.

Important! If you cook inaccurately on the stove, the small holes will be clogged with the remains of boiled milk or soup, crumbs. This happens even if an excessive amount of detergent is used. Therefore, try not to bring the burners to the point where the blue fuel stops flowing into the burner.

If the problem still arises, then it is necessary to remove the burner, thoroughly clean the divider or nozzle with a knitting needle or needle.

Important! Some models of gas stoves have plastic valve handles, put on the stem by means of a metal plate that is inserted into the groove. The handles begin to loosen with use, the plate flies out and is simply lost. Don't be upset, you can fix the problem. Take the most ordinary metal lid for canning or from a tin can, carefully cut out a suitable plate with scissors and insert it into a special groove on the handle.

If over time the handles of the valves began to turn tightly or sink, then they should be lubricated and the drains should be cleaned from oil, grease, and dirt. Enough:

Remove the handles, the front panel of the plate, which is more often fastened with latches or bolts.
Then carefully disassemble the taps, unscrew the pins holding the stem.
Then remove the spring, plug, use rags to clean them from dirt.

Important! The plug should be cleaned as carefully as possible so as not to scratch it, as this can cause gas leakage.

Next, you need to lubricate the plugs with graphite grease, but it is important not to close up the holes here.
Then you need to take the stem, clean off the dirt and grease from it with a knife, insert the plug back, insert the springs into it, and secure the stem with a hairpin.

Many housewives are faced with such a problem as a jam or a loose fit of the oven door. Repairing a gas stove in this case is very simple:

It is necessary to unscrew the screws that secure the door to the plate, but not completely.
Swing it slightly so that it returns to its place and sits firmly on the hinges.
Then it is necessary to tighten the bolts in place and check the tightness of the door. This is done simply: insert a sheet of paper between the sealant and the top edge of the plate, make sure that it is firmly pressed by the sealant.

Important! Working with modern technology can lead even the most advanced person to a dead end. We bring to your attention articles with the most common questions from oven users. Their name speaks for itself:

Not less often, the owners of gas stoves face a problem when the gas control system fails: when the burner is ignited, you press the button, and the flame burns, as soon as you release it, it immediately goes out. Don't panic right away.

The first step is to clean the thermocouple, in other words, it is the iron part that is located next to the burner. When it heats up, a current is generated that holds the solenoid valve in its working position and does not allow it to interfere with the flow of gas to the burner. If for some reason the gas goes out, the thermocouple cools down and the valve closes immediately, preventing gas from entering the room. In order for the system to start working in the previous mode, it is necessary to clean this part with sandpaper.

Important! If this procedure was not enough, then you will have to change the thermocouple.

Call an expert to repair your Ardo oven

The service center "Rem Service" provides prompt and inexpensive repair of your Ardo oven in Moscow. The most significant is the service of the master's departure and the repair of the oven at home. Since, basically, self-delivery of a broken oven is difficult and will take a lot of your time. Therefore, we ourselves will come to you at the pre-appointed time. And we will save you the hassle of transporting the oven to a repair service. Our masters will be able to provide technical assistance today if there are problems in the operation of the equipment.

Get a consultation find out the price of repair

You can find out the approximate cost of repairing an Ardo oven at the very first contact with the dispatcher by phone. You will need to give the following information to the master: brand, model, product number of the oven. You can find this information in the instructions. And if they are lost, then on the oven itself there is service sticker , with technical data. It is located on the oven body in several places. And also tell us what happened to your oven (the nature of the malfunction). So that the master knows in advance what he will face, and what equipment and spare parts he will need. According to the symptoms of malfunction you listed, the wizard will inform you about the probable causes of breakdowns and the estimated cost of repairing them (minimum and maximum price segment). The minimum repair price includes the work performed by the master. Maximum price includes labor and cost of replacement parts. The cost of parts depends on the model of the vehicle. The exact cost of repairs is determined after diagnosis.

The seal between the door and the oven body is torn or comes off. The rubber seal is an important element of the oven, without it or when it is deformed, the door does not fit snugly against the oven body. As a result, the heat does not persist and leaves the chamber, which is fraught with long heating, and this is a waste of electricity. Also, from the hot air leaving the oven, plastic elements (control knobs, buttons) on the control panel can melt.

Moscow, Ryazansky prospect, 77 (Entrance from the 4th Veshnyakovsky prospect, Workshop sign, go down to the ground floor)

Repair of built-in ovens, air grills, blenders, crepe makers, hobs, fans.

Manufacturers: Ardo, 01THE ONE, 1 TOY, 10moons, 2N, 2VV.

Vykhino

Kuzminki

Ryazan Avenue

Moscow, Bratislavskaya st., 18k1

Repair of built-in ovens, treadmills, exercise bikes, rowing machines, strength machines, hobs.

Manufacturers: Ardo, AEG, AVEX, Aeon, Aero, AeroCool.

Bratislava

Lyublino

Maryino

Moscow, Paustovskogo st., 2/34

Repair of built-in ovens, car TVs and monitors, MP3 players, car radios, dictaphones, karaoke.

Manufacturers: Ardo, ACME, AEE, AEG, AEROVISION, AIC.

+ 7 (495) 545-06-08 (multichannel)

+7 (901) 543-79-74 (multichannel)

Bitsevsky Park

Yasenevo

Novoyasenevskaya

Moscow, Miklukho-Maklaya st., 53k1

Repair of built-in ovens, air grills, blenders, crepe makers, hobs.

Manufacturers: Ardo, 4Good, A319, A4Tech, AEG, AIC.

Belyaevo

Kaluga

Konkovo

Moscow, Ryazan prospect, 40/2

Repair of built-in ovens, air grills, blenders, crepe makers, hobs, fans.

Manufacturers: Ardo, 3M, 3Q, 4Good, A&D, AAD.

Vykhino

Kuzminki

Ryazan Avenue

Moscow, Zhuravleva pl., 10

Repair of built-in ovens, MP3 players, acoustic systems, karaoke, headphones, vinyl disc players.

Manufacturers: Ardo, A4Tech, AAD, ADATA, AEG, AMC.

Preobrazhenskaya square

Semenovskaya

Electrozavodskaya

Moscow, Izmailovsky blvd, 43

Repair of built-in ovens, acoustic systems, music centers, headphones, amplifiers and receivers, air grills.

Manufacturers: Ardo, Acer, Asko, AstraLux, Asus, Atlantic.

Izmailovskaya

May Day

Shchelkovskaya

Moscow, Zubovsky blvd, 21k23, building 2

Repair of built-in ovens, hobs, hoods, coffee machines, freezers.

Manufacturers: Ardo, Acson, Ariston, Asko, AstraLux, Aurora.

+7 (499) 348-20-47 • Multichannel

8 (800) 250-30-34 • Free call

Kropotkinskaya

Park of Culture

Frunzenskaya

Moscow, Lianozovsky pr-d, 8

Repair of built-in ovens, voice recorders, radio tape recorders, music centers, vinyl record players, radio, radio receivers.

Manufacturers: Ardo, AIWA Trading, Aiwa, Akai, Ariston, Asko.

Altufevo

Moscow, Masterkova st., 6 (Shopping center Shoe center, 2nd floor, pav. 1E)

Repair of built-in ovens, MP3 players, car radios, acoustic systems, voice recorders, karaoke.

Manufacturers: Ardo, 4Good, A319, A4Tech, AEG, AIC.

Avtozavodskaya

Dubrovka

Technopark

The organization was checked by the administration of the portal and provided documents officially confirming the conduct of these activities, as well as the conduct of the reception of citizens or the presence of a workshop at the specified address.

Telephones for communication:

Operator: 8 (495) 506 81 52

Master: 8 (903) 297 35 57

Didn't get through?

8 (909) 240 90 51

127224 Moscow

st. Severodvinskaya 13

Repair of electric stoves Ardo Ardo

The appearance of Ardo electric stoves on the Russian market was imperceptible. They gradually won the trust of our customers, as advertising for this brand claimed excellent performance at a low price. But we know that kitchen appliances cannot last forever and there comes a time when they break and require repair. If a stove malfunction affects your everyday life, stops working and brings a lot of inconvenience, our craftsmen are at your service.

We will undertake the repair of the Ardo electric stove, despite the complexity of the work and the nature of the breakdown. The list of our service includes such malfunctions as: insufficient heating in the oven; switching off or switching off the hotplate; automatic operation and many other breakdowns. We recommend that you do not try to fix anything yourself. Do-it-yourself repair without knowledge of electrical engineering leads only to disappointment and aggravation of the problem, and the danger of electric shock to injury. That is why we advise you to entrust the repair to our craftsmen, who will arrive at the address on the day of your call.

Our service repairs any kitchen equipment that helps you cook. We provide related services, such as: repair of the Ardo hob and repair of Ardo ovens regardless of energy consumption, even modern induction ones. Our service is responsible for its repairs, so we leave a guarantee for a period of 1 month to 1 year.

Video (click to play).

We diagnose the electric stove by phone, so the cost of this service for you is

Rate the article:

Grade 3.2 who voted: 85