DIY pvc door repair

In detail: do-it-yourself pvc door repair from a real master for the site my.housecope.com.

Any balcony plastic doors need periodic adjustments and minor repairs, which can be done independently using a screwdriver and other common tools at hand. The main thing is to correctly assess the degree of complexity of the breakdown. In case of lack of confidence in one's abilities or serious problems, unprofessional intervention can aggravate the situation and lead to the complete failure of the door and, accordingly, its replacement.

While the windows and doors are under warranty, of course, it is better to entrust all work to the installer. However, the longer the window-door unit stands, the greater the likelihood of defects, which can be caused by various reasons:

installation errors;
natural shrinkage of the building, especially new buildings;
negligent use of products, lack of proper care and preventive measures;
sudden temperature changes, increased exposure to solar radiation.

Regardless of the cause of the occurrence, malfunctions of the balcony door lead to drafts, deterioration of the heat and sound insulation of the room, and in case of neglected problems, it is impossible to fully use the window and door structure.

Do not ignore any slight change in the tightness of the door, since even a slight sagging can lead to more serious deformations of the door leaf. The sooner you fix the problem, the less the risk of other breakdowns and the greater the level of comfort in the room. Such a defect in operation can arise for several reasons:

sagging of the canvas under its own weight;
bad or worn seal;
failure of door fittings.

Video (click to play).

The real reason for incomplete opening / closing is not always obvious. To quickly find and fix it, it is recommended to consistently inspect and adjust important components.

This is the first and main type of minor repairs to a balcony door, as follows:

Determine and mark the place with a pencil where the canvas touches the frame - the adjustment will be carried out by pulling the corresponding loop in the opposite direction.
Remove the plastic plugs that cover the hinge screws. The upper screw adjusts the blade travel in the vertical plane, the lower screw in the horizontal one. Using the hex key, carefully tighten the desired screw in several movements in the desired direction. Slides the door left or right Raises or lowers the door

If blowing from the side of the loop itself

Check the fit of the door leaf. Replace the plugs.

A common problem that is especially felt in winter is cracks in the line where the canvas meets the frame. Through them, cold air, noise and dust enter the room. On the side edge of the sash there are several eccentrics that can be used to adjust the tightness of the door.

Insert the hex key into the trunnion

You can find problem areas using paper: clamp a small sheet between the canvas and the frame and close the door tightly. If the fit is good, then it will hold on by falling and not moving. Otherwise, you need to adjust the eccentric to the desired level. In the same way, check the tightness of the sash to the frame along the entire door height, adjust if necessary. If blowing from the side of the loop itself:

There are unpleasant situations when the door is completely blocked, or it remains hanging on one hinge, in this case, watch the video instruction:

The expired service life and mechanical damage to the rubber seal are the next probable reason for the sagging and poor adhesion of the web. As a rule, the service life of the gaskets is several years after the door is installed, then they must be replaced. Sequence of work:

Carefully remove the old seal from the groove, avoiding damaging the web. Remove dust and glue from the groove.

Insert a new one, evenly distributing it around the entire perimeter without creases or wrinkles, starting from the bottom of the door. To properly lay material that is too hard, the seal must be cut in the corners and additionally fixed with glue.

Cut off excess sealant, fix the edges with glue. Allow time to dry - do not close the door during this time.

If these manipulations did not lead to an improvement in the situation, it is better to contact a specialist - it may be necessary to replace the fittings.

If the door fits snugly against the frame, but the closing mechanism does not work, then the reason is usually in the handle or core. A loose handle can be easily repaired. For this you need:

turn the decorative plug covering the attachment points to the canvas by 90 degrees;
tighten the screws with a screwdriver, adjusting the degree of pressure;
put the plug back in place.

If the core is broken, the handle cannot be repaired. In this case, it can be easily changed to a new one. For this:

Rotate the plug at the base, freeing access to the fastening screws.
Unscrew the screws with a Phillips screwdriver.
Remove the handle with the hinge from the door structure.
Install a new one and fix with self-tapping screws.
Install a plug to mask the fasteners.
Check the quality of installation, pressure and ease of opening of the web.

If the tightness of the glass unit is broken, fogging of the inner glass is observed. In this case, it is more expedient to replace it. Broken glass, severe damage to the lower blind part of the door leaf, the desire to replace the blind leaf with a glass one or vice versa also entail the dismantling and installation of a new double-glazed window. The operation is performed in a matter of minutes in the following sequence:

Remove decorative corners (glazing beads) that cover the line of adhesion of a blank panel or glass unit to the canvas - for this, place a screwdriver or spatula in the groove and carefully separate each corner.
Now the glass unit (panel) can be easily removed and replaced with a new one.
Install the corners in their original place.

Plastic surfaces lend themselves well to restoration. Depending on the degree of damage, defects can be eliminated in several ways:

Small scratches are masked with a special pencil or Cosmofen liquid plastic.

Deeper damage and chips are filled with sealant or cosmetic glue. After the filler has dried, the surface of the canvas is sanded with fine sandpaper and covered with decorative paint.

The squeak of the hinges not only causes discomfort when using the structure, but also serves as a signal that the factory lubricant has been used up and a new batch is required, otherwise the hardware may fail. For the convenience and accuracy of the work, it is better to use a syringe, which must be filled with any machine oil. Sequence:

Remove the upper hinge plugs and pour oil into the hole.
Make several opening-closing movements to distribute the lubricant more evenly and faster. Make sure the creak is gone.
Remove excess oil, close plugs.

In order for plastic doors to serve for a long time and without problems, one must not forget about leaving, prevent breakdowns in time. Fundamental rules:

regularly treat the mechanisms with oil, and the rubber seal with a special spray - all care products can be purchased from window installers or specialized stores;
regularly tighten the fastening of the handles;
monitor the tightness of the door to the frame - if necessary, adjust the hinges;
when opening / closing, turn the handle strictly to the required angle;
avoid mechanical stress, excessive overlapping on the door leaf and glass unit.

You can eliminate minor defects of plastic doors, make small adjustments to the hinges and handles on your own. It is better to entrust larger repairs (re-weighing, restoring the tightness of welded seams, replacing torn hinges) to professionals - it is difficult to independently perform this type of repair with the required level of quality.

In order to ensure trouble-free operation, you need to monitor the technical condition of the PVC balcony door. It is better to repair plastic balcony doors regularly. Often, minor problems arise that take a minimum of time to fix. Double-glazed windows need to be repaired less often, since their sashes do not sag under their own weight.

Hinged system made of PVC profile.

Sliding mechanism for balcony plastic construction.

On the eve of work, it is better to purchase all the necessary materials in advance so as not to waste time on searching in the process.

You will need the following materials:

New hardware to replace broken parts;
Plastic gaskets;
Liquid plastic and sealant (for removing scratches or cracks on plastic);
If there are cracks in the glass unit itself, it is better to replace it. It is advisable to entrust the determination of the exact dimensions to specialists.
A new insulation will be needed if the system was installed a long time ago (regardless of the presence of visible damage). In this case, the material can be replaced in advance to avoid problems.

Currently, most structures for window and balcony openings are made of PVC profiles. The company that installs the glass unit also carries out technical control during the warranty period and fixes faults free of charge. However, after the end of the warranty, the likelihood of breakdowns only increases, so it is important to understand how the balcony sash is being repaired.

Repair of the swing system lock on the loggia.

Swing sash with additional secure locks.

Repair of the sliding system lock.

Sliding opening system.

To eliminate sagging, hexagons are used to repair fittings.

Work order:

1. Remove the plugs from the hinges;

2. The upper screw allows you to adjust the structure vertically using a hexagon. To do this, turn the tool clockwise. Thus, the canvas will be attracted to the loop;

3. The end screw moves the structure horizontally;

4. Adjust another loop if necessary.

What to do if the glass unit is displaced and the door does not close?

We dismantle the glazing beads that fix the glass unit. We carry out the work with special blades;
We separate the glass unit from the canvas in the area of the hinges, using a spatula for this. Fill the gap with a plastic gasket;
We check the quality of work - the mechanism should close normally.
Installation of glazing beads in the same place.

During operation, cracks may appear on the material, sometimes it loses its shape or breaks. If a similar stage of wear has occurred, it is best to replace the seal strip.

Correct sequence:

You should buy a new material that will fully correspond to the previous one (in type and size);
Dismantle the old tape;
The groove should be thoroughly cleaned of glue residues and accumulated dust;
We install a new seal, the tape can be pressed down with a finger, but not pulled (the groove must be dry). The sealant is laid starting from the bottom. This principle is easy to explain: if a part of the tape comes off during operation, it will not sag;
The final step is to cut off the ends of the sealant, and fix the laid edges of the material with glue.Do not close the door while the glue is drying.

To increase the service life of the seal, the material must be coated every six months with a special agent that will not allow drying. You can purchase a protective compound from PVC window manufacturers.

This procedure is considered the simplest when compared with other problems. Depending on the degree of breakdown, this element can be tightened in the right places, adjusted or replaced.

If the handle is loose, turn the base plank 90 degrees. Thus, it will be possible to regulate the self-tapping screws that attract the element to the PVC profile. In order to better fix the part, use a screwdriver.Self-adjustment of self-tapping screws with a screwdriver. Image - DIY pvc door repair

The need for replacement may come to light unexpectedly when inspecting the mechanism.

Let's consider the order of actions:

Turn the handle or part that is preserved parallel to the floor;
We remove the plug, which is located at the base (turn by 90 degrees);
We unscrew the screws with a Phillips screwdriver;
Dismantle the handle together with the rod from the structure;
We install a new mechanism in the socket. In the event that the rod is too long, you need to saw it off with a special machine;
We fix the screws. In the process, you need to control the force in order to avoid damage to the handle itself or the PVC profile;
We mount the latch back, masking the screws;
We check the installed part, namely the door clamp and the handle free play.

Removing the handle with a Phillips screwdriver.

Usually, the handle is installed from the inside of the room, but this is not always convenient.

Restoration of the plastic surface is the elimination of cracks and scratches.Plastic recovery methods:1. Minor damage can be removed with a special Cosmofen compound. After exposure to the agent, the surface is covered with "liquid plastic".2. When repairing significant flaws on the plastic, use cosmetic glue, which is used to fill the gaps. A white sealant is also suitable for filling deep cracks. After the aggregate dries, the surface is sanded with fine emery paper.3. The final stage of restoration is surface treatment with a special construction pencil.Sometimes, when eliminating sagging, the door is pulled too tight, after which it is difficult to close it. Image - DIY pvc door repair

It is better to entrust this work to professionals in order to avoid unpleasant consequences: condensation, frozen glass, problems with operation. If the warranty period is valid, you should contact the company that installed the PVC structure. Installing yourself may adversely affect the appearance.

Installers' mistake during installation and incorrect adjustment of the fittings;
Shrinkage of the new building and deformation of the structure;
Incorrect operation of PVC structures;
Excessive exposure to the sun (if the sun's rays constantly fall on the balcony);
Sudden changes in air temperature.

In the event that such problems arise during operation, repair is necessary. Moreover, such malfunctions can be eliminated independently, without the involvement of experienced specialists. In order for the work to be successful, it is necessary to objectively analyze the volume of cases and the availability of free time. If you appreciate that there is not enough free time, then contact the professionals.

Plastic doors are deservedly considered one of the most reliable options for any premises. Despite this, even the most reliable door can break under serious loads, as well as during long-term use. Repair of plastic doors is quite possible. The complexity of the repair differs depending on the specific breakdown. Most often, the problems are minor and are eliminated by a small adjustment of the mechanisms, or by replacing the fittings. Repair costs are generally low.In addition, breakdowns are eliminated as soon as possible.

There are several typical breakdowns that occur most often. Such breakdowns include:

Problematic opening and closing of the door (problems caused by adjustment failure, in particular sagging and skewing of the structure);
Insufficient tightness of the door handle to the leaf, loosening of the mechanism;
Broken fittings, in particular: locks, other locking mechanisms, handles, latches;
Cracks and other damage to the glass unit;
Problems with the door seal;
The need to restore the canvas due to the resulting mechanical damage.

Each breakdown requires a specific approach to its elimination. Most problems can be eliminated without resorting to the services of a wizard. Let's take a closer look at how the above types of breakdowns are eliminated.

In the vast majority of cases, problematic opening and closing is caused by a malfunction in the adjustment of mechanisms. The adjustment process does not take much time, repairing a plastic door in such cases is the most simple. Let's consider the adjustment procedure in stages.

First of all, when the door sags, as well as problems with its opening and closing, it is necessary to determine the place in which the canvas contacts the frame. At the point of contact (displacement), a line is drawn with a simple pencil.

The adjustment is to move the blade to the side opposite to the place where the sash touches the frame. For example, if the door catches the upper edge of the frame, it is necessary to move the door leaf down and away from the point of contact.

The adjustment is simple enough. The top and middle hinges have hex screws. Turning the key clockwise presses the canvas against the hinges, counterclockwise - unclenches them. Such repair of plastic doors is quite simple.

The bottom hinge is also adjustable. The screw, which is located at the end of the hinge, adjusts the web in the vertical direction, and the screw on the side - in the horizontal direction.

If the door is fitted with glass, adjustment is possible with a glass unit. For this, the glazing bead is removed, on which the glass is held, and then, with the help of a wooden spatula, the glass unit is moved to the side until the sagging is corrected. Spacers are inserted into the gap where the blade was. After adjustment, the belt should move freely. Upon completion of the adjustment procedure, the glazing beads are installed back, while they should not be confused in places. Incorrect installation can lead to cracks in the web.

It is very simple to repair plastic doors if the repair consists in adjusting a loose handle. The fact is that with increased loads on the mechanism, as well as with prolonged operation, the fasteners of the handles are often unscrewed from the socket by one or several turns. Because of this, the handle begins to hang characteristically.

The elimination of the problem consists in removing the decorative cap from the door and then tightening the dangling screw. The screws can be replaced if necessary.

Repair of a plastic door cannot always be completed without replacing its structural elements. If the locking mechanism breaks down, it is much easier to remove and replace it than to carry out repairs. Locking mechanisms can be purchased at any hardware store. Any other fittings, in particular, a broken doorknob, change in the same way.

Failure of a double-glazed window is a serious problem. The fact is that cracks in glass cannot be completely eliminated. There are special fluids for repairing cracks, however at certain angles, due to the refraction of light, the crack will still be visible. In such cases, replacement of the entire glass unit is required.It is very expensive to repair plastic doors with a broken glass unit, therefore it is necessary not to subject the glass to mechanical stress, to protect it from sudden temperature changes.

One of the main functions of doors is noise and heat insulation of the room. The gasket plays an important role, as it ensures a tight fit of the canvas to the box, does not allow sounds to pass through and retains heat. During operation, the seal wears out, loses its properties.

To replace the seal, you must first select a replacement of the appropriate dimension. It can be purchased at any hardware store. The old seal is removed, and the new one is glued to the door using special glue. It should be noted that the repair of a plastic balcony door, if it is necessary to replace the seal, is no different from the repair of any other PVC doors.

With prolonged operation of the doors, as well as with mechanical stress, various damages can occur on the door leaf. Plastic doors are repaired by plastic restoration. Such restoration is possible with the help of special compounds that mask damage. They can be purchased at specialized hardware stores. If it is necessary to really qualitatively repair plastic doors that have mechanical damage, it is better to contact a specialist. Only a professional can restore the door to its original state, completely masking all damage.

So, you can repair a plastic door with your own hands, having certain skills and knowledge. Some breakdowns are not significant for repair, and some should be entrusted to specialists. Carrying out repairs yourself, you can save money and spend money on something more necessary.

Reinforced-plastic doors are in great demand. This type of product benefits from ease of use, beautiful appearance and durability with proper care before moisture. At the same time, depending on the preferences of the customer, the dimensions of the products can be made of any shape and size.

However, over time, any structure wears out and needs adjustment. In this regard, in order to save the family budget, it is important to know how to repair a plastic balcony door with your own hands without involving the labor of specialized companies.

During the operation of PVC products, it is important to know that there are many special devices that can extend the life of these structures, namely:

Opening restriction rail. It will protect the doors from hitting the slopes.
Microlift. A device whose function is to additionally support the door. As a rule, it finds its obligatory application when using heavy structures.

When buying plastic doors for a balcony or loggia, immediately take care to maximize their service life.

To do this, install a closer (microlift), and also protect the structure from impacts with a limiter. Then they will serve you for a long time without requiring repair.

The reason for malfunctions is often a cheap profile and fittings. Such structures often do not withstand increased loads on fasteners. Added to this is sloppy handling and the absence of a limiter.

PVC doors, like any other structures, during operation require periodic repair and control over their functioning. If these works are not carried out in a timely manner, then over time, a complete replacement of products will be required.

It is recommended to regularly, at least 2 times a year, inspect the plastic door. Timely adjustments will help avoid future breakdowns. In this regard, it will be relevant to consider the most common malfunctions in the operation of plastic structures and ways to eliminate them:

replacement of fittings and rubber seal;
replacement of the lock or its parts;
elimination of scratches and dents;
elimination of malfunctions by means of adjustment;
replacement of a cracked glass unit,

When repairing plastic balcony doors, sometimes you have to remove them from their hinges. This should be done carefully so as not to damage the constituent elements. When disassembling, follow the steps below:

Remove the plugs from the curtains.
Push the axle screw down as far as the stop.
Leaning slightly forward, remove the structure from the hinges.

After the replacement of the fittings, we hang the canvas in the reverse order.

It is not difficult to repair a plastic door, for this it is necessary to prepare materials and tools in advance and only then proceed with the repair.

During the operation of the door structure, the following violations in its operation are often encountered:

The door starts to sag, the frame is rubbed against the threshold from below. In such a situation, we are looking for a screw on the top panel and tighten it with a hexagon, aligning the verticality of the product. If the reason is not eliminated or not completely eliminated, you need to remove the cap from the lower curtain, where the adjustment screw is located, which is responsible for the position of the curtain above the threshold, and slightly tighten it.
The side of the box is rubbed. Open the lower curtain, look for a side screw on the inside of the canvas. Turning it clockwise, we tighten the canvas. Additional adjustments can be made in the upper curtains.
Loose linens to the box. For this, there are special adjusting eccentrics at the ends of the door leaf. We make the adjustment with three eccentrics at once, turning them with equal efforts. Additionally, we increase the tighter tightness of the closure using the upper and lower hinges. There are special adjusting bolts for this purpose. For more information on adjusting the balcony door, see this video:

You can solve the problem of adjusting the door yourself using the most ordinary hex key.

Repairing a loose handle is easy. We find a decorative plate behind the handle, easily pulling it towards ourselves and turning it 90 degrees, the adjusting screws open to our eyes. They securely hold the handle on the canvas.

In the case of a loose handle, tighten the screws clockwise. If it is necessary to replace the handle or its constituent elements, we unscrew the fasteners and insert new devices.

If the lock has broken, you need to disassemble it and find out the reason. To do this, remove the handles and core. We unscrew the screws that hold the lock and take it out.

First of all, it is necessary to lubricate the entire locking mechanism, after which we check its operation with a key.

If carrying out these manipulations did not lead to the desired result, we change the lock for a new product.

Your seal is worn out and does not protect against blowing out - it's time to replace it.

First you need to purchase a special rubber cord and glue, by the way, German will serve you longer than others. Next, we perform the following actions:

we take out the old cord with its remnants;
remove dirt and degrease;
apply glue with a continuous strip;
starting at the corner, inserts a new cord.

In order for the seal to serve for a long time, it is recommended to lubricate it with a special silicone grease for rubber 2 times a year, but you can use ordinary petroleum jelly for this.

If you decide to change the double-glazed window, to do this, remove the casing with a plastic spatula, which holds it in the frame. We remove dust and debris, degrease the frame. When everything dries up, we insert a new glass unit, securing it with the removed glazing beads.

To eliminate problems with the installation of a new glass unit, it is important to accurately measure its optimal dimensions in advance. To do this, use a ruler or tape measure to measure the distance of the glass unit, including the thickness of the retaining glazing beads.For more information on how to replace a glass unit, see this video:

There are dents or scratches on your door that spoil your interior, they should be redecorated. Degrease the damaged areas.

Apply a special putty with a rubber spatula. We are waiting for complete drying, grind, cover with glossy or matte varnish.

When installing PVC products, it is important to remember that periodic repair, adjustment and replacement, regular replacement of fittings is the key to the reliable functioning of these structures.

Very often, when installing new plastic structures, windows or doors, problems arise with the opening-closing mechanisms or other functions. This is due to many factors: improper installation, shrinkage of the house or careless operation. To eliminate the trouble, you should not call the master: adjusting PVC doors with your own hands is quite possible. Moreover, the master will require a rather large sum for his services, and this is a reason to save the family budget.

For high-quality adjustment, only three tools are required: an Allen key No. 4, a screwdriver and an eccentric. They are versatile, since the design of plastic products involves their use. All fittings have special holes for tools, mainly hinges and handles.

Installation diagram of the door leaf.

Horizontal adjustment involves pulling up the top and bottom hinges. The door should be open at this time. If you turn the key clockwise, the sash will be attracted to the hinge and, conversely, may loosen the fastening. In this way, the bottom of the door is adjusted. If you stand on the outside of the PVC door, then, working with the lower hinges, you can tighten or loosen the top of the sash. This method of adjustment allows the door to be brought into parallel alignment with other plastic structural elements.
The eccentric is supposed to be used in the sash pressure adjustment. Very often, the main function of metal-plastic doors is far from ideal. Therefore, with the help of such a key, you can bring it to the desired state. To do this, the eccentric is brought into the pressure pads along the entire perimeter of the door. The key has a special risk, showing the degree of clamping. All this can be seen clearly when used. In addition to the eccentric, the sash can be clamped with special plates or, on the hinge side, with a hexagon. Doors can be installed depending on the season: weaker in summer, vice versa in winter. But it is worth knowing that with increased pressure, the sash structure can quickly wear out.

The hinge clamping implies greater reliability of a heavy structure. Adjustment is carried out using a key corresponding to the bolt perpendicular to the sash. First of all, you need to remove the caps from the hinges and set the canvas open. With this type of installation, the door must be held, because there is a risk that the structure can fly off, holding on only on one hinge, which is not subject to adjustment, and also the entire canvas can be in the ventilation mode, that is, rejected. By turning the key, you can adjust the hinges either upper or both at once, thus achieving a snug fit of the fittings.

The sash may sag due to its heavy weight. Therefore, the adjustable parts, i.e. the hinges, are tightened with a hex key. Depending on the symmetry of the door, both or one are pulled up. The elimination of the defect can be seen immediately. But if this does not help, the problem is solved radically.

The door can sag due to poor installation of the glass unit when it comes to the balcony option. Such work should be provided only to the masters of their craft, otherwise there is a risk of permanently spoiling the structure. They can remove the glazing beads and either change the glass or adjust its installation. It will not be possible to solve the problem on your own without having the knowledge.

Visually, this defect will be noticeable immediately.The problem is eliminated by using the built-in regulators. The bottom and top are twisted in accordance with the parallelism of the sash to the door frame.

Drafts due to the seal

Perhaps the most common problem in the operation of PVC doors. The issue is solved by pressing the sash with an eccentric. It is not worth delaying troubleshooting for a long time: drafts can bring dampness, which is not very good for a sealant. If it is dilapidated, the rubber should be changed immediately, no pressure will help, on the contrary, too zealous will lead to PVC bending.

If these are hinges, they are tightened with a hexagon, installation is carried out crosswise, in case of failure of both elements, and in the usual way for one. It is imperative to control the pulling force. Otherwise, in this case, pinching can lead to other consequences, and adjustment will be needed for other parts of the structure.
To securely attach the handles, tighten the bolts by turning the handle 90 degrees. This is done with a screwdriver. In addition, a ventilation comb can be installed in the base of the door handle.

Bad or difficult turning of the hardware

In addition to the fact that the PVC door requires regular inspection and tightening, all undercarriages should be lubricated with machine oil, using cotton swabs for this, so as not to leave greasy stains on the surface.

There are some simple tricks for the door to show its own defects immediately when adjusting. Then the likelihood that unscrupulous craftsmen will return the money spent on the construction will increase.

With a simple pencil. In this way, the parallelism of the frame or web guides can be checked. The door closes tightly, and the structure is drawn with a pencil around the perimeter of the entire canvas. After that, the drawn contour can visually reveal the overly drawn sashes. The adjustment takes place from the side where the lines are not parallel. If the sash can sin on two sides or one, after working with keys, this is a reason to call the masters.
Method for detecting flap clamping defects using a piece of paper. To do this, the door is closed with a piece of newspaper and then pulled back. If this happens easily, the door needs to be adjusted with an eccentric.
The door can spontaneously perform its functions, open and close without any action on the part of the owners. This indicates a poor fitment installation. If the adjustment does not help, you need to call the company where this design was made.
Also, the adjustment period may be a consequence of poor installation.

As a rule, it is not required for properly made doors. Defective ones or in violation of the installation technology will require editing almost immediately. You need to be vigilant when installing PVC doors with your own hands.

Many problems during the operation of doors can be avoided by entrusting the installation to trusted companies.

But it is not always worth sinning on shameless craftsmen: it is quite possible that your own negligence has led to such consequences, and the problem can be eliminated by yourself, without resorting to expensive repairs.

Video (click to play).

If neither budget nor time allows to tinker with repairs and adjustments, you need to be extremely careful when choosing a PVC production company, reading reviews about it and checking the list of product certificates provided. The guarantee is also important not only for the service life, but also for the repair. And with the above recommendations, adjusting the door will not be difficult. Good luck!