DIY electric cultivator repair

Service center "Servy" performs post-warranty service and repair of cultivators "Hyundai" - the entire range of petrol, electric Hyundai cultivators.

• Model range of Hyundai cultivators accepted for repair
• Hyundai cultivator repair cost

We repair the following models of Hyundai cultivators:

• Hyundai petrol cultivator models
  • repair of the Petrol cultivator Hyundai DAT T 700
  • repair of the Petrol cultivator Hyundai DAT T 800
  • repair of the Petrol cultivator Hyundai DAT T 850
  • repair of the Petrol cultivator Hyundai DAT T 1200
  • Hyundai electric cultivator models
    • repair of the Electric cultivator Hyundai Т 1500E
    • repair of the Electric cultivator Hyundai Т 2000E

    * If you did not find your model in the above list, do not be upset, we carry out repairs on almost all Hyundai cultivators. Just leave a request for repair on the website or call us By phone - our Servi specialists will answer any of your questions.

    The final cost of the necessary repair of Hyundai cultivators largely depends on the prices of spare parts and is agreed with the customer by phone, after the diagnostics carried out by the wizard.

    In our service center you can order spare parts and accessories for Hyundai cultivators... We work on pre-ordering spare parts. The most common items are always in our warehouse! We order unique spare parts and accessories directly from manufacturers without extra charges, the delivery time varies from 5 to 30 working days.

    Video (click to play).

    The availability, completeness and cost of the necessary spare parts can be clarified without any problems by calling us by phone or by leaving a request for spare parts on the website.

    According to Servy statistics, the main faults* when working with Hyundai cultivators are:

    1. The cutters do not turn on the Hyundai petrol cultivator - reasons: wear of the gearbox parts (gear wheel, sprocket), wear of the belt / chain of the cutter drive, the control cable of the cutter drive is not adjusted / damaged;
    2. The Hyundai petrol cultivator does not run, possible reasons: worn out parts of the travel drive assembly (gear wheels), wear of the travel drive belt, not adjusted / damaged drive control cable;
    3. A Hyundai cultivator with a gasoline engine does not start, there is no sparking - reasons: a spark plug is faulty, an ignition coil (magneto) is faulty, a manual starter is damaged, a fuel system is clogged, a cylinder-piston group is worn out;
    4. The Hyundai petrol cultivator stalls - reasons: blockage of the fuel system (no fuel supply), wear of the cylinder-piston group, misaligned carburetor, blockage of the air filter.
    1. Hyundai electric cultivator does not turn on - reasons: the electric cable is damaged, the switch is faulty, the electric motor is faulty;
    2. The electric (battery) cultivator Hyundai does not spin the cutters, possible causes of the breakdown: the cutter bushing is damaged, the electric motor is not working;
    3. The Hyundai cultivator does not plow, the main reasons: the drive belt is worn out or torn, the drive reducer is out of order, the drive gears of the driving cutters are worn out, the drive belt tension is not adjusted, the travel control cable is not adjusted.

    

    These defects are typical for Hyundai cultivators: some are more common, others less common. And not infrequently they occur due to the simplest reasons: improper operation (no maintenance is carried out), the use of a poor-quality gasoline mixture (oil and gasoline), many hours of uninterrupted operation of the cultivator, turning the cultivator body on its side or with the wheels up. However, with the correct and professional approach, all breakdowns can be easily repaired by the specialists of the Servy service center in Moscow.

    Just leave a request for the repair of Hyundai cultivators on the website or call us By phone - our Servi specialists will answer any of your questions.

    • The exact timing of the repair is always indicated only after diagnosis. • The cost of Servi's services are for informational purposes only and can be changed after diagnostics of your equipment. We work with each client individually and a detailed calculation of the repair price is made in accordance with the level of complexity of a particular type of equipment breakdown. • Spare parts that we use for repair are paid separately. • Calculation based on data from the Servy customer base.

    Buying a cultivator greatly simplifies the process of performing summer cottage work of a various nature. It's not a secret for anyone that such equipment can break down and still breaks down. So that the summer resident does not have to buy a new unit, he must understand how to independently repair the cultivator. Let's discuss this issue later in this article.

    All working components of cultivators during their operation are subject to rather heavy loads. For this reason, they need regular inspection and repair. First you need to configure the ignition and fuel pump systems of the unit. Indeed, in the winter period of time, he was idle "without work", which can cause problems with starting the engine. It is also worth checking the transmission. Remember, negligence at this stage of work can lead to serious breakdowns and the need to overhaul the cultivators.

    To do it yourself, you need to mature at the root of the issue. That is, to understand the cause of the malfunction, and in which unit of the apparatus it arose.

    Conventionally, all breakdowns of equipment of this type can be divided into two groups:

    • breakdown of the engine of the apparatus;
    • breakdown of other parts of the equipment.

    According to the reviews of experienced summer residents who use Texas or Mole cultivators on their plots, problems of the first group are more common. How to carry out repairs yourself will become clear if you read this article to the end.

    

    To repair the cultivator engine, as in the following photo, you need to determine the root cause of the problem. There may be several: let's discuss each option.

    1. In cases where the engine of the apparatus does not start at all, perform the following sequence of actions:
    • Turn on the ignition;
    • Check the gasoline level;
    • Open the fuel cock;
    • Check carefully the air damper of the Texas walk-behind tractor carburetor: it should be tightly closed if you start a cold engine;

    

    

    1. The motor of the Mole cultivator does not give power due to such problems:
    • The air filter is clogged: repairing the cultivator with your own hands will be reduced to cleaning it;
    • The muffler is clogged: it should be disassembled and washed;
    • The carburetor of the Mole cultivator is dirty: it needs to be dismantled, cleaned and adjusted.

    You will need to repair the cultivator gearbox if its operation is accompanied by increased noise. A similar phenomenon is typical in the case of a lack of oil. Add it to the gearbox of the device, or better, replace it altogether.

    

    Also, noise can arise due to the "loosening" of the fasteners of the nodes: inspect and fix them with your own hands.

    In addition, summer residents may face the problem of oil leakage from the gearbox. This can occur due to wear or improper installation of the seals of the bearing units, with poorly fixed covers and deformation of their accompanying gaskets. Replacement and subsequent high-quality installation of oil seals, self-replacement of gaskets and fixing of cover fasteners, as well as high-quality cleaning of the breather will help to eliminate such a leak.

    Do not forget to timely change those parts of the Texas gearbox that are more susceptible to wear than others during the operation of equipment of this kind.

    

    Excessive vibration of the device during its operation is typical for those cases when the summer resident has poorly performed the adjustment of the attachments of the attachments. Stop the equipment the minute vibration is noticed and adjust the attachment parts accordingly.If the fasteners are worn out, they will need to be replaced with new ones.
    

    
    Rough running can be caused by wheel problems. Adjust the pressure in each of them in order to fix the problem.

    

    This article described the most common problems that summer residents may face when preparing a cultivator for the new season. You can eliminate them with your own hands without much difficulty, but you need to approach this task responsibly. The video in this article will once again tell you in detail about the features of the repair of cultivators.

    one per entry "How to independently repair the cultivator"

    Where to find carburetor and valve adjustments texas 532 lili TG

    I took it through ozone. Price (5999 rubles) with delivery (589 rubles) - 6588 rubles.

    The main work is loosening the beds - peat with sand. The volume of work is small - about 10 beds, plus two 6-meter greenhouses.

    

    
    1. After opening the box, a pungent smell (of Chinese rubber?) Unambiguously confirmed the country of the manufacturer - China

    

    

    it is clearly seen that the gearbox is collapsible, the bolts are tightened, no oil (grease) leaks were noticed on the gearbox.
    p.s.
    I did not find any holes for filling oil on the gearbox housing, the instructions on page 18 indicate:
    “Lubrication. All gears are supplied with factory lubrication. The gearbox must be lubricated once a year by an authorized service center. ”

    

    

    langepac wrote:
    it is clearly seen that it is collapsible, the bolts are tightened, no oil leaks were noticed on the gearbox.

    The first disappointment is a cutter, the metal is soft, the file is biting into without much effort. The photo clearly shows the risk from a single filing with the edge of the file.

    

    

    Pavel003 wrote:
    Is there oil in it?

    I didn’t make it out, I didn’t see the filler holes. In appearance (worm gear) and size, it is presumably not oil but grease in it. further there will be photos with the removed engine.

    The engine is all in a plastic case,
    there is a metal gear to reduce the rotation speed

    Gear wheel on metal shaft with pressed-in bearing
    into the plastic motor housing.

    

    

    The general impression after disassembly-assembly: neat assembly, thick plastic case, parts are precisely fitted. Thick and sturdy plastic for the engine housing. Confused by the placement of the reduction gear on the plastic motor housing.
    At the very least, the cultivator should be stored only in a warm room; Chinese plastic often cracks after frost.
    The noise of the engine when turned on is comparable to the sound of a 2-kilowatt circular saw.
    As for the cultivator's cutters and their quality - the line can be drawn after field tests - in our area it will be possible only in May.
    In general, I'm happy so far.

    have not tested yet?
    I got the same yesterday.
    looking forward to the weekend, doing field tests

    Yes, I'm interested too. You just need to dig up 3-4 acres and there is nowhere to store a healthy cultivator at home. This baby with 2 horses seems to be able to cope.
    Interestingly, and will take the virgin soil, albeit in several passes?

    Yft wrote:
    Yes, I'm interested too. You just need to dig up 3-4 acres and there is nowhere to store a healthy cultivator at home. This baby with 2 horses seems to be able to cope.
    Interestingly, and will take the virgin soil, albeit in several passes?

    Here read Temko. ”> Closer to the end, where that is about your type, the user unsubscribed.

    ynota wrote:
    Here read Temko. ”> Closer to the end, where that is about your type, the user unsubscribed.

    Yes, I also came across this Temko. It's just that here in one chain store it is sold for 1tyr cheaper than elsewhere, and the power should be enough according to the calculations, even if longer, well, I will make a garden bed not in 10 minutes, but in 30 minutes, there is not a big difference.

    DED57RUS wrote:
    have not tested yet?
    I got the same yesterday.
    looking forward to the weekend, doing field tests

    Last weekend I finally tried it.
    the results exceeded expectations.
    2 hundred square meters of virgin soil dug up under a shovel in the fall, passed in 2 hours 2 times,
    the first pass pulled the cultivator towards itself, backed forward, the second pass was cultivated across the already plowed one, facing forward, as expected)).
    He walked from the side so as not to trample the plowed, hyundaychik bit into the ground up to the protective shield.
    I tried a piece of land where I had not been digging for 10 years, with difficulty, but plowing, it took a long time, a plot of 2X10m. gnawed for an hour and a half in three passes.
    then he cultivated a plot for a lawn, sown with rye in the fall, about two acres, did not time the time, but ran quickly on half of the cutters.
    In general, I'm happy with the shovel (and the neighbors called my miracle a vacuum cleaner, probably out of envy)) _), my wife also tried to “plow” and everything worked out))).
    For a small suburban area that's what you need. Moreover, it is planned to constantly cultivate the land only on the beds of about 2 acres, the rest is lawn, paths, trees.
    I am not going to buy anything more serious.
    Of the minuses - I want to sharpen the cutters, but I don't know yet whether I need to sharpen them or not,
    if anyone knows write.

    For most gardeners, the summer cottage season will begin with a grueling and laborious activity - digging up the earth with a shovel. After all, well-treated soil is the key to a rich harvest. However, such manual labor is exhausting even for a physically healthy person. A motor cultivator will plow the land much faster and with minimal effort for the summer resident. In our article we will tell you how to choose the right assistant.

    A motor-cultivator is a complex technical product designed to work for more than one season; its choice should be taken seriously. Despite the variety of cultivators on sale, it is better to give preference to products of a well-known and reputable manufacturer, for example, such as HYUNDAI.

    Reliable and efficient motors of our own design, ergonomic design, high-quality assembly and reasonable cost - these are the components of the popularity of HYUNDAI cultivators in Russia.

    Whether you are a budding 3-acre gardener or an expansive landowner, Hyundai's cultivator range will satisfy any buyer.

    The line of HYUNDAI cultivators includes both ultra-light electric cultivators and semi-professional gasoline units for farms and public utilities. To find the right HYUNDAI cultivator for your needs, assess the condition of the soil and the size of your plot.

    HYUNDAI cultivators can be roughly divided into 3 groups: light, medium and heavy.

    If you are the owner of a small area divided into zones, beds and flower beds, then the lightweight HYUNDAI cultivator will be an excellent solution for you. This category of cultivators is equipped with low power electric and petrol engines.

    Lightweight electric cultivators HYUNDAI T1500E and T2000E loosen the soil to the optimum depth for planting plants - up to 25 cm. HYUNDAI electric cultivators are environmentally friendly, silent, compact and lightweight - up to 30 kg. The electric cultivator is so easy to operate that a woman or an elderly person can easily handle it. It is enough to connect it to the network and you can work.

    The HYUNDAI T 500 model with a 3.5 hp four-stroke gasoline engine, forged milling cutters and a chain transmission, which is a rarity for machines of this class, also belongs to light cultivators. The chain transmission transfers up to 100% of the torque from the engine to the cutters, the cultivator quickly and with less resistance is buried in the soil.

    The HYUNDAI T 500 is the ideal companion for loosening small to medium sized plots of already cultivated land.

    To quickly process larger areas from 4 to 10 acres, more powerful gasoline cultivators with a working width of cutters from 60 cm are required - middle class cultivators HYUNDAI T 700, T 800 and T 850.

    These popular and practical cultivators have a powerful petrol engine of at least 5.5 HP.with lightweight starting system, rigid steel frame and forged saber cutters.

    A plow and other attachments can be installed on the HYUNDAI T 800 petrol cultivator

    Thanks to this equipment, they can loosen even caked soil to a considerable depth - up to 32 cm.

    Despite the solid weight (from 40 to 52 kg), the middle-class HYUNDAI cultivators are ergonomic and easy to operate due to the well-developed design - most of the cultivator's weight falls on the cutters, and not on the operator's hands.

    The cultivators with reverse gear HYUNDAI T 800 and T 850 are ideal for maneuvering in areas of complex shape with dense ground. The reverse gear function is powered by the unique HYUNDAI twin-shaft engine. The twin-shaft engine has no analogues among other manufacturers, it has an increased service life, a reduced noise and vibration level, due to the presence of two shafts rotating in different directions.

    The HYUNDAI T 850 model has the most powerful engine in its class of 6.5 hp, which, with a fairly compact size and a weight of 52 kg, allows you to work the soil up to 90 cm wide.

    For the cultivation of vast land areas of more than 10 acres, we recommend heavy units weighing more than 50 kg with a two-shaft engine - T 900 (6.5 HP), HYUNDAI T 1000 (7 HP) and HYUNDAI T 1100 (7 HP) .). HYUNDAI heavy cultivators have a horizontally and vertically adjustable operator panel, a transport wheel with an increased diameter for comfortable movement and modular saber cutters with a working width of up to 90 cm.These powerful machines weighing more than 50 kg can work both virgin soil and soil with dense turf ...

    Among heavy cultivators, the HYUNDAI T 1000 unit deserves special attention. This cultivator, equipped with a second reduction gear, can work even on clay soil. The second gear reduces the number of revolutions of the cutters with a parallel increase in torque.

    The HYUNDAI T 1100 walk-behind tractor also belongs to the group of heavy cultivators. This walk-behind cultivator can not only process heavy soils up to 90 cm wide thanks to saber cutters and a powerful 7.0 hp engine, but also transport loads weighing up to 300 kg on a special trailer HYUNDAI Trailer 1100 (sold separately). It is enough to replace the cutters with pneumatic wheels, which are supplied in the kit, and connect the trolley using a hitch.

    The dream of any gardener about the complete mechanization of land work is quite feasible. With the attachment kits, HYUNDAI cultivators turn into multifunctional machines that can huddle, cut furrows and even plow the ground!

    Universal attachments for medium and heavy HYUNDAI cultivators: grouser wheels, opener plow, hiller plow, extensions, hitch

    Gardening work will only bring joy, because all the difficult work for you will quickly and efficiently be done by the HYUNDAI cultivator!

    Our service center Lawn-Mos offers its numerous customers repair services for Hyundai motor cultivators. Has an engine, carburetor or other part or assembly in your unit broken down? Our first-class specialists will always come to the rescue and eliminate any, even the most complex malfunction.

    We carry out repair of Hyundai motor cultivators not only in the workshop, but also at the customer's home. Contact our operator and leave your request. If necessary, they will answer all your questions.

    • affordable prices;
    • professionalism of employees;
    • a wide range of services;
    • reliability;
    • efficiency;
    • high quality.

    To read the instructions, select the file in the list that you want to download, click on the “Download” button and you will be redirected to the page where you will need to enter the code from the picture. If the answer is correct, a button will appear in place of the picture to receive the file.

    If there is a “View” button in the field with the file, it means that you can view the instruction online without having to download it to your computer.

    If your material is not complete or you need additional information on this device, for example, a driver, additional files such as firmware or firmware, then you can ask a question to the moderators and members of our community, who will try to promptly respond to your question.

    You can also view the instructions on your Android device.

    I did this. I went through the gearbox of my Hyundai put 2 bearings 6004 (20/42/12) two oil seals size 20/42/7 and two bushings chiselled width 8 mm inner diameter 20 outer 24. First you put the bushings to the thrust ring (of course on the lower shaft) rings there from the factory, then the bearing is point-blank to the sleeve. You put oil seals in the gearbox housing. In the half of the gearbox, drill a hole in the lower part so that when filling the gear oil, the third part of the sprocket is in oil. The hole is closed with a bolt with a seal so that the oil does not leak out. This hole will be both filler and check (for oil level). We smear the gasket with sealant, assemble the gearbox and fill in 150 grams of oil or until it flows out of the hole. I bought 2 cutters from the champion (landing 20), the diameter of the cutters was 27. They were also double, cut and installed the first from the gearbox on both sides, and then the relatives. It turned out 66 cm of cultivated soil. All cutters are removable. You can work on 4x and 2x and 6. The wings had to be increased, otherwise the earth is thrown.

    Thanks for the good advice. In winter, I’ll probably do some revision, as the gearbox resource will not be enough for the next season. Everything would be told in such a constructive way, otherwise they just throw themselves with “slippers” that I am advertising a cultivator.

    Good day ! I have the same cultivator - but it's in the village! far away and I do not remember the diameter of the shafts of the gearbox where the cutters are mounted. If it's not difficult, tell me! I can't find it on the Internet. for vidos -like

    thank you very much . I think to make a stock cutter - thanks again and good luck !! and subscription

    Good afternoon. Shaft common, 20mm in diameter. The inner diameter of the cutters for fitting on the shaft is 20.5 mm.

    The cultivator is the assistant who will turn the cultivation of the site from "hard labor" into a simple, somewhat even exciting work. So, let's take a closer look at what Korean engineers are offering us?

    The HYUNDAI T1500 E electric garden cultivator is a modern, compact, fairly mobile device designed for plowing land in small areas. The power of 1.5 kilowatts is quite enough for the device to work for a rather long time without overheating the electric motor. The characteristics of the electrical network (220 V, 50 Hz), standard for Russia, make it possible to connect a garden gadget at almost any electrified summer cottage. The working depth corresponding to the cutter diameter (200 mm) allows penetration into the soil to the height of the shovel bayonet, to which our gardeners are so accustomed. Thanks to the use of a worm gear in the design of the cultivator, one and a half kilowatts of engine power are converted into "heroic" torque transmitted to the cutters. This is quite enough to chop up rather large roots, which come across a lot in the soil during spring and autumn plowing. The 300 mm wide swath makes the cultivator convenient when working between rows or when working in confined spaces such as a greenhouse. And one more pleasant surprise that Korean developers have prepared for us: the weight of the device is only 13.5 kilograms! Even a teenager can handle such a weight.

    For more convenient movement around the summer cottage, the cultivator wheels have an adjustable height. The motor control lever is protected against accidental starting, which makes it safe to use the device.

    But that's not all! HYUNDAI engineers took care of how to make convenient not only the operation of the cultivator, but also its transportation and storage. The handles with which the gardener controls the cultivator were made removable. Disassembled, the device can easily fit not only in the trunk of a solid SUV, but also in an ordinary passenger sedan. You don't need a special tool for disassembly and assembly.The fasteners are designed in such a way that all operations can be done without the use of keys and screwdrivers.

    Now directly about the very process of soil cultivation. After plowing with the HYUNDAI T1500 E cultivator, you do not have to break up the remaining clods of earth, as is the case when digging with a shovel. You just have to level the soil a little with a rake, and the bed is ready!

    Are you still thinking? Right! After all, we have not yet talked about the shortcomings of the HYUNDAI T1500 E cultivator. And they, like every device, of course, are. But there are not many of them. Let's see?

    The first and probably the most significant drawback of the cultivator is, of course, its attachment to the electrical network. Therefore, before purchasing this model, you need to think carefully about for what needs and in what conditions you plan to use this device. Lack of autonomy, we pay for light weight and comfort. Similar gasoline-powered devices are several times heavier, less environmentally friendly and noisier.

    Second disadvantage. Even if there is order in your summer cottage with electricity, you will have to purchase a good carrier to work throughout the garden. Good not only in terms of length (you will decide on this yourself). The electrical cable must be rated for high inrush currents. A copper cable with a cross section of 2 × 1.5 sq. Mm will be sufficient.

    That seems to be all. We examined the "pros" and "cons" of the HYUNDAI T1500 E electric cultivator. To take or not to take? You decide! For some, a shovel is a way to keep yourself in great physical shape. For some, back pain is an integral part of the dacha "rest". And someone wants to free up more time for themselves to communicate with loved ones in nature, with a barbecue, and preserve physical strength for the coming week of work. The choice is yours, dear gardeners!

    In order to always have a high-quality crop on your site, it is necessary to properly cultivate the soil. In modern agriculture, such a type of technique as a cultivator is quite common. They plow the land for them, prepare it for planting. If in the past most of the work was carried out by hand with shovels, today it is easy to cultivate the land with a cultivator.

    However, a cultivator can not only loosen the soil. The device levels the soil, makes beds, furrows. In addition, the cultivator can be used for uprooting weeds, for fertilizing, as well as for digging out crops.

    It should be noted that the cultivator is a technique that requires significant investment. Nobody wants to buy expensive dacha equipment, and then after a couple of weeks hand it over for spare parts. And this happens very often. The thing is that the cultivator is not always used for its intended purpose and correctly. The problem is not a factory defect.

    In order not to constantly spend money on the repair of the cultivator, you yourself need to know its device for proper maintenance and care, and also so that it can be repaired at any time. In addition, you need to know some operating rules.

    Before buying a cultivator, you need to figure out what types of them exist on sale today.

    • Light cultivators... Their use is limited to summer cottages, which have an area of ​​no more than twelve acres. The mass of such devices is relatively small. Hence, they are easy to carry. But there is one drawback: light cultivators do not plow deep into the ground. The maximum is twenty centimeters.
    • Medium cultivator you can process up to fifty acres at once. The device is larger in size and weight.
    • The best option is heavy cultivator... The device weighs more than ninety kilograms. Its power is such that it is allowed to use various types of equipment with it, as well as trailers, mounted platforms.

    All cultivators use gasoline or diesel fuel as fuel.Gasoline, of course, ensures the reliability of the use of equipment, but the cost of fuel is high. There are also electric cultivators. Everything is simple here: there is an electric motor. However, there are limitations - everything is related to the power source. The longer the cord, the more the area can be processed. It is important that there are no drops in the network. Recently, cordless cultivators have been on sale. Their advantage lies in their mobility. After the battery is charged, the device can be used as long as the charge runs out.

    When buying a cultivator, you need to pay attention to the area of ​​the site. If you have a small area to cultivate, you can buy an electric cultivator. For a large area, it is best to buy a gasoline or battery unit.

    A prerequisite is high-quality equipment. For example, handles should be comfortable to work with. There should be no roughness on them. And, of course, in the future, proper care of the cultivator, which will be purchased, will be required.

    Manual cultivator for giving

    In our country, cultivators that run on gasoline are most actively used. The devices are powered by a gasoline engine. This unit is perfect for those who need to process very large areas. Indeed, the technology can handle large areas due to its high productivity. Moreover, work can be performed not only near the house, but also in the field. Of course, gas powered cultivators can be heavy, medium and light. Today it is not difficult to find any cultivator on sale that may be needed on the farm.

    A gasoline engine is certainly powerful and efficient, but it needs to be serviced regularly. You can repair cultivators at home. However, if you are not sure that the work can be done on your own, then you need to take the equipment to a special workshop, where professionals will carry out the proper repairs.

    So, what kind of work do specialists perform when repairing cultivators? First of all, the whole apparatus is diagnosed. Then some parts may be repaired. If necessary, the broken part is replaced with a new one. Lubrication of the mechanisms is in progress.

    Of course, cultivators can also be repaired at home. But for this you need to have a certain knowledge of technology, as well as a set of tools. It should be noted right away that the cultivator is a simple technique. It has a motor, frame and gearbox. In addition, there is a control system and holders. Now you need to consider all the mechanisms separately and understand how to repair them.

    The frame is the heaviest and most durable part in the cultivator. It carries not only the engine, but also the gearbox, as well as other parts of the equipment. In order for the frame not to deteriorate, after each work, it is necessary to remove the remains of soil from it and clean it. Protective shields must be installed on the frame. This is necessary so that you can protect yourself if a stone pops out from under the cutter or the belt on the gearbox bursts. During operation, the soil bounces both to the frame and to the engine, which is associated with frequent repairs of equipment.

    There are chain and worm gearboxes on cultivators. Any gearbox is characterized by the use of lubricants. In order for the gearbox to work properly, it is necessary to constantly monitor that oil does not leak out at the joints of the gearbox parts. Change the oil in the gearbox once every two seasons. To prevent oil from leaking out of the gearbox through the breather, you need to move the equipment vertically.

    From the engine, the torque is transmitted to the gearbox through a chain drive. As soon as the first signs of damage to the belt appear, it must be replaced immediately. There must be a guard on the belt drive. At the same time, when changing the belt, you can clean the wheels on which the belt is attached.

    Choose dry weather for work.Wet soil puts additional stress on the device.

    On all cultivators, the engine is the main element. Basically, four-stroke engines are installed that run on gasoline. The assembly is carried out in such a way that at any time you can access all the parts that most often need to be repaired. Engine maintenance is an important factor that needs to be considered in more detail. But more on that later.

    The handles on the cultivator will wear out over time. Therefore, it is necessary to replace them in a timely manner for comfortable work. The cable on the cultivator is a drive element. The cable must always be securely fastened.

    When storing cultivators, many equipment owners make obvious mistakes. For example, you should always drain the gasoline as soon as the cultivator goes into storage. The fact is that the gasoline left in the tank will deteriorate over time. The fuel system begins to deteriorate when condensation and sediment appear in the gas tank.

    The carburetor suffers the most. After work, you need to drain the gasoline from the carburetor through a special tap. You can generally work with technology until it stops by itself. This means that the fuel has run out completely.

    To ensure that the hoses do not deteriorate in the fuel system, you should always buy only high-quality fuel. Moreover, occasionally it is necessary to check the hoses for integrity. It is recommended to install a fine fuel filter.

    The filter, candles should always be cleaned on time. Filters are made of foam and paper. Use a compressor to clean the paper filter. Foam filters must be thoroughly washed and then lubricated with oil. It is recommended to clean the filter once a season.

    The cultivators have air-cooled motors. Therefore, it is recommended to clean the dust cover as often as possible. This is the only way to ensure a normal air supply to the engine, which overheats during operation.

    It is forbidden to use candles that have carbon deposits. If the cultivator is not used for a long time, then the candles must be unscrewed. In order for the engine to start after a pause in operation to be carried out efficiently and quickly, it is necessary to pump fuel.

    We constantly monitor the level of engine oil in the engine of the cultivator. Without oil, the engine will quickly fail. Modern engines won't start if they don't have enough oil. The crankcase has a special hole through which the oil level is measured with a dipstick. The first time the oil must be changed after five hours of operation. Then the oil is changed every 25 hours.