In detail: do-it-yourself fly iq441 repair from a real master for the site my.housecope.com.
Fly phones set records in Russia, this should not be surprising, they have built the right strategy in the segment of cheap smartphones: price, quality, positioning. In the first quarter of 2014, Fly ranked 2nd in terms of sales in quantitative terms, overtaking Apple and behind only Samsung. From the side of the service center, we can say that repairing Fly makes sense, unlike most other Chinese and Koreans, due to the high popularity of models, there are a sufficient number of spare parts on the market. We in the VKontakte group conducted a survey on how much users are willing to pay for repairs, most are ready to part with the amount of about 25% of the original cost of a smartphone. Fly devices fall into this selection, so we present to your attention an article: how to replace a broken glass and a Fly iQ4411 Energie 2 touchscreen.
Before starting the repair, remove the back cover and battery. A memory card and a sim card are taken out of the slots. 11 screws are removed from the case! Yes, FLy do not fall apart when dropped, because in their design, by the standards of modern mobile construction, a fairly large number of fastening elements are used. After unfastening the back frame, which is held by 6 latches.
Unscrew a few more screws from the top board, unfasten three cables from the connectors and remove two boards from the case. The bottom board is just nested. The motherboard is a large board. A small narrow runner with a power connector, vibration motor and button illumination diodes is a strange design decision. Fly could get by with a soft train, which is cheaper and stronger when deformed. It is not for us to condemn Chinese engineers, their right to choose what to make cheap smartphones from.
 |
Video (click to play). |
The Fly iQ4411 case is made of plastic, in order to separate the glass with the touchscreen from the case, it will have to be heated. The temperature has to be kept lower than when the iPad Mini glass is being replaced, 140 degrees.
Having picked up the glass in the upper surviving part of the screen with a scalpel, direct the pick into the slot and slowly separate the protective glass around the perimeter.
When the glass is separated, remove the tape from the inner edges of the case, having previously glued the display with screen tape. When assembling Fly iQ4411, thin adhesive tape was used, so do not think to glue the new glass with ordinary 3M glass, the glass will stick out, cling and peel off. Pay attention to the holes for the cables, speaker and light sensors. At the bottom, you need to make slots for the backlight diodes of the Android function buttons.
Remove the display tape, the protection from the fastening tape and insert a new protective glass with a tach in place, correctly passing the loop inside the case.
Further assembly is in the reverse order of disassembly. Loops of buttons, display and wheelbarrow are attached to the motherboard. Install two screws into the motherboard. Snap on the back frame.
Fasten the frame with 11 screws, you can count it on the fingers of two hands. Put the SIM card and battery in place. Close your smartphone.
The repair time for an experienced craftsman is about an hour, replacing the iPhone 5S display is faster, since you do not have to fiddle with jewelry removal of the wheelbarrow. As you can see, replacing the Fly iQ4411 touchscreen is not a super difficult task, provided you have the necessary tools and skills. The price for replacing the Fly iQ4411 glass is 1500 rubles, as for most other devices from this manufacturer.
Turn on Fly iQ4411, check the touch for working capacity. You can give. A happy and contented client goes home to write a positive review of the work done in the service. If you encounter a similar problem, please contact our service, we repair smartphones Fly, Samsung, Nokia and others.
In this video I show how I change the glass on such a completely ordinary Chinese phone, it was glued to the B7000 glue, my impressions of the process and of the repair itself.
You can help the development of the channel by looking at the channel information section
You can send your gadgets for repairs by the Nova Poshta service
If you think that you have not wasted your time and the video is interesting, like it under the video.
My contacts can be found by clicking on the channel information tab.
- Disable smartphone;
- Remove the back cover;
- Remove the battery;
- Unscrew all screws (6 pcs.);
- Remove the back of the body with a spatula, plectrum or nails;
- Remove the volume control and power buttons;
- Remove the microphone from the groove;
- Remove the speaker;
- Gently peel off the volume control buttons from the body;
- Disconnect the sensor cable;
- Carefully remove the board.
It should be noted that the Fly touchscreen is glued to the front panel. By the way, replacing the Fly IQ434 glass means replacing the sensor. Therefore, further work will be carried out only with the front panel of the phone.
Attention! When removing the board, be sure to open the metal display latches. Otherwise, the screen of Fly IQ434 can be damaged. The actions must be carried out very carefully and slowly!
Now you need to carefully peel off the damaged sensor, trying not to break the case and not injure your hands. Remains of glue and dirt should be removed and then degreased. You can degrease with rubbing alcohol. The new sensor can now be installed. You can buy the Fly IQ434 touchscreen in specialized spare parts stores, if there are no such parts in the city, you can order it in the online store.
Next, you need to remove the film from the new touchscreen, covering the glue strips. After that, carefully place the sensor on the front panel and glue the part with light pressure. It is important to calculate the pressure here so as not to spoil the sensor. Assembling the smartphone is carried out in the reverse order. If there are fingerprints on the display or sensor, they can be removed with a soft flannel cloth. Now you know how the touchscreen is replaced on the Fly IQ434 smartphone. You can read about how to flash Fly IQ434 on this website.
This article will be devoted to the Fly IQ444 cell phone. It will describe detailed instructions for disassembly (Disassembly) of this device in pictures. The information can be useful for those who accidentally broke the display on their cell phone and want to fix it on their own. In order not to harm or aggravate the condition of your device, we do not recommend resorting to this method if you are not completely confident in yourself and do not have the necessary skills. In this case, contact a specialist for repair. So if you haven't changed your mind, then we can proceed to the analysis.
- At the first stage of parsing, remove the battery cover on the cell phone and unscrew 8 bolts around the perimeter and 1 bolt in the center between the two sim-readers.
We remove the middle part of the case. Using a spatula, starting from the top, as shown in the photo, then moving to the left and right sides of the apparatus.
After releasing the latches, remove the middle part and proceed to dismantling the board.
We remove the battery. We disconnect its connector from the board, unscrew 2 bolts on each side and one located in the middle, at the bottom of the battery.
We unscrew the three bolts securing the board. One between the display ribbon cable and the coaxial cable, the second between the vibration motor and the front camera connector, the third under the ribbon cable that connects the board with the USB connector and microphone to the main board.
Disconnect the display, the cable from the bottom board, the antenna coaxial cable and the touchscreen cable (next to the Reset button) from the board. We remove the motherboard.
Now, in order to assemble the device, it is necessary to carry out all the described points of disassembly in the reverse order.
Diagnostics and repair of Fly IQ441 Radiance phone is carried out by professional engineers of our service as soon as possible. A guarantee is issued for all types of work. You pay only for the repairs performed.
The prices in the table are for repair work, excluding the cost of spare parts.
All information provided is for reference only and is not a public offer. Check the terms and the actual cost of repairs with our specialists by phone +7 (495) 363-78-55
The Tech-Profi service center is always happy to help in solving problems that have arisen with your phone. Our engineers carry out repair of cell phones of any complexity. From replacing the display and touch glass, repairing the charger and SIM holder, to complex electrical repair of the motherboard. Our service technicians will restore Fly IQ441 Radiance after flooding or severe mechanical damage at the lowest prices in Moscow.
The addresses of our service centers:
* Discount is provided for the work of the master. Specify the exact cost by phone.
You can deliver the product yourself to our service center or use our logistics service
Upon acceptance, an acceptance certificate is drawn up and express diagnostics are done.
A full cycle of diagnostics and repair of a mobile phone (tablet) takes from 1 to 3 days.
During the repair, the master constantly informs the client about the readiness of the product and agrees on the cost.
The master consultant will check with you the operability of the phone (tablet) and only after that the payment is made
Fly IQ441 is a functional smartphone with a 2-core processor and 512 MB of RAM. Radiance has a 4.3-inch display, a 5-megapixel camera, 3G standards, Wi-Fi, two SIM card slots.
The BESTKOM service center professionally makes repair of cellular smartphones Fly Iq441 and offers its customers not only a highly qualified approach, but also more than affordable prices for repair Fly Iq441.
Correct Fly Iq441 cell phone diagnostics - the first stage of repair. Before giving the device to our company, it is advisable for the client to describe the nature of the malfunction as accurately as possible, and also talk about the reasons that could lead to the breakdown (for example, the phone falling into a puddle).
Based on the information from the client, our specialists will carry out a detailed diagnosis of the smartphone, find the cause of the malfunction and eliminate it.
In the event of a problem with the software, the product will most likely display this fault as follows:
- Will stop turning on (while connecting the product to a computer using a USB cable, it appears in the device manager).
- It will reboot, turn on and off at its discretion.
- Will refuse any module, addition (camera, Blutooth, Wi-Fi, other)
- Reveals lethargy in work and so on.
The process of reinstalling Fly Iq441 software looks like this:
- Preparation of the system itself (as a rule, it is downloaded from the official website. This is a file with the .IMG extension).
- A selection of the original USB cable, or the most suitable for such a procedure.
- Installing a software update program (Flashtool, Batchtool or any other program) on your computer.
- Connecting a gadget, which needs to be reflashed to a computer using a USB cable, and the firmware process itself by clicking upgrade.
If the software was not installed, an error appeared, or the gadget could not be started after the firmware - the reason may be a malfunction in the hardware of the equipment or incorrect installation of the software. It is important to understand that unsuccessful firmware will result in hardware failure. Incorrectly stitched devices are called "bricks". It is quite difficult to restore the "brick" of the newest versions, while the old versions can be cured by yourself by starting the firmware again.
There is one more way of flashing - through the system menu of the phone. Such an attitude is much more complicated, requires knowledge and skills, and is not suitable for a beginner. In this case, the equipment must be returned to our center.
Sensor (touchpad) and display malfunctions are very closely related to each other. Since in most cases, breaking the touchpad, the sensor also becomes unusable. If, by “spraying the web”, the sensor can still work (possibly with errors and failures), then the display will end its functioning.
Separately, these elements cannot be restored. That is, it is not possible or advisable to repair a broken sensor or display. Most often, these malfunctions are solved by replacing broken parts with new ones.
If the main element of each product - the processor - becomes unusable, then an end is put to the performance of the gadget. Most likely, such a malfunction will not be repaired.
Despite the fact that absolutely any board can be repaired by replacing a burned-out element, or by restoring a break in communication on the board, modern craftsmen do not undertake this responsible and painstaking work. After all, it is much easier and more profitable to install a new board than to restore an old one. In addition, when buying a new board for the client's device, the craftsmen keep the old parts for themselves. No wonder they can be re-soldered and put back into operation for another client.
It is in connection with the above that it is worth contacting only our company. After all, an unscrupulous employee of a private workshop can easily deceive the customer by making poor-quality repairs, thereby aggravating the situation of an already "sick" product.
Today it is hardly possible to find a person who does not have a mobile assistant in the form of a phone, which allows you to make calls from anywhere in the world, and play games, and communicate on social networks. At the same time, companies that did not have such significant market shares and the influence they have on the industry 20 years ago are gaining more and more turnover. Fly and its products can reasonably be attributed to such flagships, this company is so popular due to the cheapness and availability of smartphones around the world.
True, there are no perfect manufacturers of their devices. Often the latter are in the second or third year of life (the warranty period is just ending, and the service centers will not solve your problems for free), they start to junk a little (although, if everything is fine with your phone, it's even great). The problem is that the breakdown can be very serious, like a malfunction of the display or the contacts of the microcircuits, or maybe it’s a trifle — the loop has come off or the speaker has been "soaked" in a puddle after the phone has floated in it.
If the problem is really difficult, however, you are ready to solve it, right up to self-parsing and repair of the device, please note that you can buy the fly iq441 display separately from other spare parts at affordable prices. This means the following few nice things:
1. Repair will be cheaper, because many negligent technical centers or sellers strive to sell you something "more and more", regardless of whether you need another super-cool headphones or film on the display, or not at all.
2. You can replace it at home, however, provided that you understand this and are willing to take risks.
3. If you do not undertake to solve the problems of replacing the display alone, take it to the technical service center along with the phone. So you can really save money, because when you buy a ready-made display "on the spot", you, which is typical, overpay the "trade margin".You don't need to be an accountant or economist to understand this.
4. The screen replacement process will be much faster than if you took the phone and waited for it to be ordered and delivered. And so the master will immediately be able to start the necessary manipulations, so that everything will be done smoothly and in the shortest possible time.
In the end, keep this method in mind and share it with others!
Fly IQ441 Radiance - the first Fly phone with Android OS. An inexpensive smartphone, good enough for its functionality.
Fly IQ441 screen replacement.
Sometimes it is not difficult to understand that the Fly IQ441 Radiance screen needs replacement. This is often visible to the naked eye. For example, if extra pixels appear on the image, part of the picture is missing, the backlight is blinking or there is no backlight - there is a high probability that the display matrix is faulty, usually these signs are provoked by damage at the junctions with the cables. Lost electrical contact in the connections.
In any case, diagnostics reveal a malfunction of the display and its replacement is usually carried out within half an hour. The replacement cost, together with diagnostics and the price of the display, is shown in the table.
Fly IQ441 Radiance power button replacement... Buttons most often fail in inexpensive devices of budget models. The buttons most susceptible to wear are those that the owner uses more often. Usually this power button or Home. A little less often you have to change the volume buttons. Replacement prices, if they are not in the tables, you can clarify by calling our phones, preferably directly to the repairman.
Fly IQ441 glass and sensor replacement.
In the overwhelming majority of modern phones, the sensor and glass are a single element and their separate installation is not structurally provided. Fly IQ441 glass replacement implies the mandatory installation of a new touchscreen. They are simply glued together.
Sensor replacement (again with glass) is necessary after mandatory preliminary diagnosis, because with similar symptoms (when the touchscreen does not work), a software glitch or a processor malfunction can occur, for example.
Replacing the USB connector.
Those users who often use the data exchange of their phone with external devices using the USB port may suffer damage from constant mechanical stress in the places where the connector pins are connected to the board. There is a breakdown in electrical contact and a failure in data transmission. Communication may be erratic or non-existent. If the contact cannot be restored, the connector must be replaced. Most phones use this connector to charge the phone, which creates additional mechanical stress and premature wear on the Micro-USB connector.
To protect the Fly smartphone from negative mechanical influences, it is advisable to use special protective covers (bumpers), which can play a decisive role, for example, when the phone is dropped. Liquid penetration into the smartphone can also cause significant harm. For example, the phone has been dropped into water, or alcoholic drinks, tea or coffee have been spilled on it. In such cases, it is necessary to contact the service center in a timely manner to eliminate possible damage, even if it is currently working and there are no signs of negative consequences visually. Oxidative or other chemical reactions over several days or weeks can destroy contact joints, metal parts of elements or conductive tracks.
If vertical or horizontal stripes appear on the screen of a Fly smartphone, or a part of the screen does not work, most likely the display is faulty. The display cable may have been damaged. The touchscreen (touch panel) IQ441 may one day fail to work completely unexpectedly and the smartphone will lose control, not responding to touching the screen. In such cases, a diagnosis of the malfunction is necessary and the sensor may need to be replaced. In modern smartphones, glass replacement is often not structurally provided separately from the sensor and display.In order to increase the strength of the structure, manufacturers often glue them into a single module and it is impossible to change the protective glass separately, which significantly increases the cost of repairs in case of damage to the screen elements. In some cases, options are possible only after consultation with the master.
With frequent use of certain IQ441 control buttons, they may be subject to premature wear. Those that are used more often tend to break down faster and faster. Consequently, this is why, most often, during repairs, the smartphone's power button must be replaced. A little less often you have to change the HOME button or volume buttons. About the availability of buttons in the warehouse and the possibility of replacing them, call our phones.
The most susceptible to premature wear is the USB connector of mobile phones, which is used to charge the mobile phone battery. The loads on it can not always be predictable during charging and talking at the same time. Active users of headphones and microphones expose the Fly headset connector to increased mechanical stress, which may one day require replacement due to natural or premature wear and tear. About the possibility of replacing connectors for your model (IQ441) and their availability in our warehouse, please call the indicated phones. Repair or replacement of sensors is possible depending on their availability in the warehouse.
Service center for repairing the Fly IQ441 Radiance phone: replacement of glass, screen, repair after water, does not charge, discharges quickly, does not turn on, repair of the power button.
Free diagnostics and consultations by phone +7 (495) 210-13-90.
Glass replacement with Fly IQ441 Radiance using Oca film.
- Repair price - 1800 rubles.
- Professional equipment allows you to change the glass according to the factory technology.
Master consultation
Display replacement within 1 hour.
- Repair price - 1000 rubles.
- Own spare parts warehouse.
- It is possible for a courier to leave there and back.
Master consultation
Does not charge, move the wire and charge goes, the connector itself is broken
- Replacing the connector within 1 hour.
- Repair price - 1400 rubles.
Master consultation
Fly IQ441 Radiance stopped seeing SIM card, SIM card was not pulled out or inserted correctly
- Replacing the sim rider connector within 1 hour.
- Replacement price - 1800 rubles.
Master consultation
Fly IQ441 Radiance does not hold a charge well, discharges quickly, turns off and does not turn on or takes a long time to charge
- Battery replacement within 20 minutes.
- Repair price - 1000 rubles.
Master consultation
On Fly IQ441 Radiance, the interlocutor is hard to hear or not heard at all
- Replacement of the earpiece within 30 minutes.
- Repair price - 1400 rubles.
Master consultation
On Fly IQ441 Radiance, the interlocutor hears you badly or does not hear at all
- Replacement of the earpiece within 1 hour.
- Repair price - 1800 rubles.
Master consultation
Recovery after water, free diagnostics within 1 hour
- Much depends on the water itself and how long it has been in it. Call and check with our managers.
Master consultation
The list contains the main repair procedures performed with the Fly IQ441 Radiance phone. To repair your Fly IQ441 Radiance, you can drive up to our service center, or order a free courier in Moscow. Guarantee for all work performed. Prices are indicated for the work, excluding the cost of spare parts.
In block diagnostics, it is determined which specific element (housing, protective glass, sensor, printed circuit board, connectors, speakers, microphone, antenna, battery) is out of order.
- Checking sayadku, if the phone is fully charged, otherwise:
- We check the phone connector, if it works, then:
- If all of the above does not suit you, then you will need to reflash or repair the phone's motherboard.
- Checking PI will lose the chargeif the phone battery is charged then:
- We check and whether it is correct power button on the phone;
- If nothing was found at this stage, the cause of the breakdown, we recall - if the phone was flooded with liquid, or the phone fell and stopped turning on, most likely the phone's motherboard will need to be repaired.
- Check if the phone detects another sim cardif it detects then:
- Checking Phone settingsif the settings are correct then:
- Phone flashing is required.
- Checking phone flash cardif serviceable then:
- Checking USB flash drive connector on the phone, if it is also working properly, then:
- You need to flash your phone, or to remot the phone's motherboard.
- Checking usb cableif the cable is ok then:
- We check the phone connector, if it is ok then:
- You need a motherboard repair or phone flashing.
- Checking settings, if the settings are correct, then:
- Checking Internet connection, if the connection is stable, then you need to reflash your phone.
- Checking Phone settingsif the settings are correct then:
- Checking WiFi adapter phone, if the order requires a flashing of the phone.
- Checking connection cable to the computer if the cable is whole then:
- Checking driver phone on the computer, if the correct drivers are installed, then:
- Phone flashing is required.
- Checking for availability physical damage screen, if not then:
- Checking display cable phone, if the loop is intact, then:
- Phone flashing or motherboard repair is required.
- We check the integrity of the touch screen for damage, if it is intact then:
- Checking touch screen flex, if int, then:
- Phone flashing is required, or controller repair display.
- Checking Phone settingsif the settings are correct then:
- We check the integrity of the microphone, if it is intact:
- Check if it works microphone controller if it works on the phone:
- Phone flashing is required.
Every day we listen to music on the phone, connect the charger, connect the phone to the computer, and naturally these connectors are subject to constant wear and tear, which subsequently leads to breakdowns of the Fly IQ441 connectors.
- Broken usb connector on Fly IQ441:
- When the USB cable is connected, the computer does not detect the Fly IQ441, or the connected device is not detected, or external signs of breakage are visible - the core of the connector is broken, the outer part of the connector is broken. Also, when connecting another cable, the same problems arise.
- Broken charger connector on Fly IQ441:
- Fly IQ441 does not charge when the charger is connected, the connector is broken. You can also determine that the connector is defective by connecting another charger. If the charging connector is outwardly working, but the phone does not charge, then the phone's motherboard will probably need to be repaired.
- Broken audio connector on Fly IQ441:
- There is no sound when connecting the headphones, or external breakdowns are visible. Also, the problem may be in the phone's settings, or in the firmware.
Repairing any Fly IQ441 connector means removing the broken connector from the motherboard and replacing it with a similar new connector.
Do not postpone repairing the Fly IQ441 connector until the connector is completely out of order. its use in a semi-working condition can damage the elements located near the connector, and as a result, it may be necessary to restore the board, replace adjacent elements.
Every year, phones perform more and more functions, and are already mini-computers. And for stable operation, a debugged operating system is required.
You may need to flash your phone for most problems - from the fact that the phone stopped detecting the computer to the fact that the phone's display stopped working.
- Microphone is not working for Fly IQ441;
- The sensor stopped working on the Fly IQ441 phone:
- Fly IQ441 phone turns on, but there is no image on the screen or it is garbled by the phone:
- Fly IQ441 cannot see the computer;
- Fly IQ441 does not connect to Wifi;
- Fly IQ441 is not updated;
- Fly IQ441 will not turn on or does not load;
- Fly IQ441 phone does not connect to the network or does not see the sim card;
- Fly IQ441 does not see an SD card, does not detect a USB flash drive;
- Fly IQ441 not charging via usb.
In most cases, Fly IQ441 phone problems arise due to firmware or incorrect updating. Due to a failure in the phone's firmware, the settings get lost, or the drivers of some controllers fail, and some functions may simply stop working.
Miklukho Maclay: Greetings from the FUTURE! The author, however, was not destiny to explain that under the touch buttons, there is factory tape, that you need to be careful and you can break the screen !? Thank you! Now I have a brick, with a new touchscreen and a cracked screen!
Yuri Gerasimets: Why disconnect all the cables, do you like extra work?
GueDanHit WoT: thanks a lot! You helped me a lot!
Clas Of Overlord Over TV: Are your spare parts delivered to Russia or not? kst zaf you tore off all the trains when you only had to cut one off? 😕
the worlds is mine: Thanks a lot for the video, it helped a lot.
Minecraft Macho: Where are you, bro?
dvijok63v4: Thank you. Changed the screen with minimal cost =)
Alex Smith: Lol, thermoblower
Azamat077: Glory can you tell me the battery from 441 flies is suitable for 445 flies?
Roman Esengeldinov: “Replacing the touch screen” - then why the hell did you disconnect everything that caught your eye if you only need to remove ONE cable ?! PS those would first have watched a video of this nature before taking on themselves!
Driver Mechanic: disassembled the phone with his stepfather tore off the train, he rattled it on the floor))
samvel ezoyan: the same question on Fly IQ440, is it glued there too?
Max Fax: I wouldn't give you the phone for repairs. One mumbles cheto in the ear, the other forgot to unscrew the bolts and bends the plate. And this is just me 3 minutes looked
Simba Simbaba: On the new glass, by the way, there is no damping or sealing strip along the inner perimeter, which is in contact with the display frame.
Warface Warfake: I changed the screen and did everything. But I turn on the smartphone, everything turns on by the tap, that is, it’s like I’m poking at the screen.
What the hell am I doing wrong, or what.Maxim Yalovoy: Does the Fly 4410 also change or is the touchscreen glued to the module?
– -: I want to correct the author of the video and simplify the work of everyone who will change the sensor.
Here are some amendments:
1. It is not necessary to disconnect all the cables, it is enough to disconnect the cable of the proximity sensor and the old sensor.
2. The tabletop hot air gun can be replaced with an ordinary household hair dryer (take it from your girlfriend, well, or take it from your mother) or a building hair dryer (here your father will help you).
3. Of all the screwdrivers, you only need PH 0 (you do not need to buy sets for 200-300 rubles, such a screwdriver costs from 30 rubles in a hardware store).
4. The scalpel can be replaced with a regular 9mm stationery knife.
5. Tweezers are not needed at all.
6. The mediator can be replaced with any unnecessary plastic card, well, or the one you need.
7. Someone wrote in the comments that the display can be glued to the sensor with double-sided tape (I didn't have one), so after we unscrew the additional screws and disconnect the sensor cable, carefully use a plastic card (for guitarists with a pick) to try to disconnect the front cover from sensor from the board, CAREFULLY! If it gives in easily, then the display was forgotten to stick to the sensor.
Look like that's it.Roman Voronenko: At 2.47 what did he say? the quality is shit, small details are not visible, how to disconnect the loop and buttons?
Spherical Horse in Vacuum: Do you have any instructions on how to replace a wheelbarrow with a Fly IQ442? 441 is, 443 is, but there is no middle. Or tell me, is there a sensor just like here, on the frame? Or is it glued to the display? I would not want to drop the display when disassembling it.
More information on our website -
In this video, we talked about the disassembly and repair of the Fly IQ441 mobile phone, namely, the replacement of the touch screen
You will need:
- new touchscreen
- tabletop hot air gun with adjustment
- Screwdriver Set
- scalpel
- tweezers
- double-sided tape
- and other little thingsPrices are valid for and include the cost of work and spare parts.
Want to get your phone repaired but don't have time to travel?
Call our courier! - It's completely free!A distinctive feature of this smartphone is that it became the first Fly phone, for which Android was chosen as the OS. The technical characteristics of the device are quite acceptable, and the user will certainly be satisfied with his "pipe", which he purchased at such an acceptable price.
Repair of Fly phones is characterized by the fact that it will cost the user less than repairing smartphones with similar technical characteristics released by other manufacturers. There is a constant proportion here: the more expensive the phone, the higher the cost of its restoration. Speaking about the repair of Fly IQ441 Radiance, it can be noted that this operation will not force the user to spend serious money, unless you choose an unscrupulous service center that will set a biased price for its services.
By contacting RemFon, you will fall into the hands of conscientious specialists. You can order repair of Fly IQ441 Radiance from us at a reasonable cost. In addition, the service center is pleased to offer its customers a range of pleasant bonuses, which will leave you with a pleasant impression of contacting our company.
Entrusting Fly IQ441 Radiance repairs to our specialists, you can be sure that the services rendered will correspond to the highest level. Our words are supported by many years of practice, over the years of which we have developed an extensive client base. People come to us because RemFon offers excellent service at affordable prices.
Fly IQ441 Radiance glass replacement
Touchscreen devices are incredibly convenient. They allow you to quickly navigate the device, moving between menu sections and individual commands. The touchscreen includes two elements - a sensor and a glass. The first is attached to the second and their separate installation is not provided. Therefore, replacing the Fly IQ441 Radiance glass becomes an automatic sensor replacement, and in some cases this phrase implies the installation of a new touchscreen.
RemFon has entered into supply contracts with companies that supply us with original Fly components. In the warehouses of the service center there is always a necessary part, thanks to which any operation, including replacement of Fly IQ441 Radiance glass, will be performed as quickly as possible.
We value the trust of our many customers, so poor-quality repairs are not in our interests. We provide first-class services, which, moreover, are charged at affordable prices.
Fly IQ441 Radiance screen replacement
The diagonal of the display in this model is 4.3 inches. Its resolution is 480 by 800 pixels. These parameters provide excellent color reproduction and sufficient picture brightness. It is not difficult to understand that you need to replace the Fly IQ441 Radiance screen. Identification of this malfunction does not even require diagnostics, which, by the way, is a free service in our service center. So, if the picture on the screen suddenly becomes not the same as before, pixels appear, the image becomes blurred, the backlight disappears or other signs of a malfunction of the matrix appear, replacing the Fly IQ441 Radiance screen is what is required to restore the normal operation of the display.
This operation at RemFon takes about an hour. We will not keep you waiting long if repairs are required urgently. In this case, we will try to fix the smartphone as quickly as possible, and we will not charge you fees for urgency. This rule has been in effect at RemFon for 4 years in a row.
Fly IQ441 Radiance power button replacement
As for this operation, it is not always possible to detect it with the naked eye. The fact is that the reason that the phone does not turn on is not always a faulty power button. Therefore, only the diagnostics will tell whether the Fly IQ441 Radiance power button needs to be replaced, or the malfunction lies in something else. For example, in a failed controller. And sometimes the battery can "pump up", and replacing the battery will return you the joy of full-fledged use of your smartphone.
Fly IQ441 Radiance power button replacement is subject to a three-month warranty.We do not charge you for repairs that were unsuccessful, and if the malfunction reappears after our SC provides the appropriate service for its elimination, we will repair the mobile phone for free.
Fly IQ441 Radiance USB connector replacement
Why do you need a USB connector, perhaps even children know. It allows you to connect the ports of a mobile phone and a computer and thus transfer data or charge a smartphone. If the phone is not displayed on the computer at the next cable connection, it does not necessarily mean that the Fly IQ441 Radiance USB connector needs to be replaced. Check if the PC port is good.
When contacting RemFon, let us know about your wishes regarding the timing of the repair. Standard replacement of Fly IQ441 Radiance USB connector is performed within 60 minutes. If you urgently need to fix this malfunction, we will promptly perform the work in the absence of constraining factors - other breakdowns that form such a definition as a "severe case".
If your Fly is broken, don't worry! - Just call +7(499)707-31-21 - we will help you as soon as possible!
Didn't you find the phone breakdown you are interested in in the list above? Do not be discouraged - just ask a question just below, in the section “Questions and Answers” - we will definitely answer you!
Benefits of our Fly service center
Completely free diagnosticsExpress repair in your presence During repairs, original spare parts are used Our experience in renovation is more than 10 years All works are guaranteed for up to 3 monthsSC "RemFon" has been repairing Fly IQ441 phones for a long time, thanks to which we know how important the ratio of repair quality, its cost and warranty for the work performed is for you. We have tried to do everything to ensure that by contacting us, you receive a high level of service for a reasonable price, a long warranty, as well as a good mood! 🙂
Our phone: +7(499)707-31-21
We are located in Center and in the South-West of Moscow:
- 3-5 minutes from the Kievskaya metro station
- 3-5 minutes from the Paveletskaya metro station
are registered trade
stamps. The site is exclusively
informational nature and is not
public offer. SC does not belong
companies and not sponsored by themVideo (click to play). Paveletskaya - 3 minutes
Leninsky Prospect - 5 minutes
Benefits of our Fly service center
Completely free diagnostics
Leninsky Prospect - 5 minutes
