DIY bayruner coil repair

Adjusting the coil with the baytraner is quite simple. But the need for its use by many anglers is questioned. In their opinion, this mechanism is convenient only in one case - for measuring depths, coupled with a marker rod, since in this case it is difficult to work with a friction brake.

It is quite difficult to adapt to it. For example, if you forget to turn it off when taking a bite, then the sweep will result in the formation of a beard, which you have to spend precious time on untangling. Often because of this, fish come off the hook. However, the majority of athletes use a bayruner successfully.

When choosing a non-inertia one, you need to understand what kind of shots it will be designed for. If fishing most of the time will be carried out in shallow water, then, purchasing a long-range reel, you can simply throw money down the drain, since the cost of these devices leaves much to be desired, which we wrote about in the article "Fishing with a reel with a baitruner - a luxury or a necessity?"

The best option would be to purchase a universal coil. After all, it is for the angler - not a reel for winding and unwinding a forest. The existing friction brake must be checked for the degree of tension of the line before each fishing trip. This is not difficult to do.

After snapping on the forestry device, you need to pull the forest. If it does not give way, the adjusting screw is turned half a turn. The operation is repeated until the spool starts to turn with effort. It is important not to let the forests go too easily, otherwise the fish will be impossible to get out of the reservoir, as it will gain an advantage.

The correct friction brake setting will significantly reduce the risk of losing fish, if you think about it to make an unexpected and powerful dash. Over time, all these actions will be worked out by the fisherman to automatism, and even at the moment of fishing he will not get confused and will adjust the friction if the size of the fish does not correspond to the degree of his effort.

The next important factor hindering successful hunting is forest twisting. It can be noted that this is often due to the illiterate use of a bayruner and a clamp. So, the forest, which comes out from their side, can twist and fit in rings when rewinding.

Most of all, the thread is twisted when the bait station is set at long distances when the baitruner is activated. In this case, it is recommended to snap off the line guide and ask a colleague to manually stretch the line. When the stacker is unlocked, the thread will no longer be twisted. This is important, since the deformed scaffold easily clings to the tulip when casting and loosens under the influence of tension.

Most of the defects arising in the coil can be repaired by yourself. Also, its regular maintenance will not interfere, in this case, prevention will not only avoid problems that arise during operation, but will also extend the life of the inertia unit.

Before dismantling, the body must be thoroughly cleaned of dirt and fish mucus. This is done with warm water and a small rag. If the inertia is too dirty, the water can be made soapy. All bends and hard-to-reach places are taken out with a cotton swab.

During disassembly, all elements are carefully laid out on the table in the order in which they were dismantled, as we wrote about in the article "Multiplier coil repair and prevention of problems." Individual units are placed on the tabletop in groups. This will make assembly easier later on.

1. First, the clutch nut and drum are removed.
2. Washers and gears under the drum are dismantled.
3. The handle is unscrewed and removed.
4. The design of the inertialess is disassembled, for which the clamping nut is unscrewed and the roller is removed.
5. The brace of the forestry device is removed and the device that latches it, the roller is disassembled through which the scaffolding slides.
6. The bolt of the backstop is unscrewed and the toggle switch is removed.
7. The bolt of the plug is unscrewed, which is dismantled.
8. The inertialess wall is removed, for which it is necessary to apply a certain effort.

After all the manipulations, a slider and a pair of gears appear to the eye - this is the main mechanism of the meat grinder. It makes no sense to make further disassembly, it is enough to put grease there, which is easy to distribute over the gears by rotating them by hand.

Repairing coils with a baytruner, as described above, is possible with your own hands, and then this will help save a lot of money. However, not all problems can be solved independently, and it is not easy to get the necessary parts, in which case the coil will have to be carried by specialists. Let's consider the main defects.

Its appearance can be caused by many reasons, from the ingress of dust and dirt to the failure of bearings or other elements. In the event of any suspicious creak, it is better not to use the inertia device so as not to aggravate the situation. In any case, it will have to be disassembled and dealt with either cleaning and lubricating, or replacing failed elements.

If this happens when deforestation occurs, it becomes a serious problem. It should be noted that coils of not the highest quality are distinguished by such a defect. If you do not react in time, there will be sad consequences in the form of a break in the rig and a fracture of the rod, not to mention the failure of the inertia gun itself. In most cases, you rarely manage to cope with this problem on your own.

No less serious defect than the previous one and can lead to exactly the same consequences. Problem caused by snapping the line guide bracket into the rewind position. If the rig is heavy enough, for example, feeder, the least you can get off with is by shooting the bait.

It is possible to try to repair the damage yourself. The first step is to tighten the bolts with which the bracket is attached. If the problem persists, the cover is dismantled, under which the spring is located, and a gasket is placed on the rod. On some models the gasket cannot be fitted, so the spring will have to be replaced.

Often, the angler has to regret to state the appearance of various scratches, dents and other unpleasant defects on the side of the spool. Due to the increasing friction of the forest, this, on the one hand, leads to a decrease in the range of the tackle, on the other hand, irreparable damage is caused to the thread itself.

The only way out of this situation is to clean and polish all problem areas with further polishing. However, you should not get carried away too much, because you can inadvertently remove the hard-alloy metal spraying from the side, for which high-quality inertialess devices are famous.

It is quite simple to determine that the backstop has suddenly failed on the coil. In this case, the grinder handle begins to rotate easily in the forward and polar directions, despite the activated blocker. Unlike older models, the stopper works thanks to the overrunning clutch.

It is in it that it is necessary to look for the reason, since in most cases the accumulation of dirt or thickened grease leads to a failure of performance. Whether you want it or not, you will have to dismantle the clutch and apply liquid lubricant to it. True, disassembling this unit is a very difficult operation, and if you are not sure, you should not do it yourself.

On some meat grinders with a front friction brake, the nut that fixes it is for some reason located a couple of millimeters above the drum edge.The forest tends to cling to it, which leads to a cliff. An independent solution to the problem is as follows.

To begin with, the entire mechanism is dismantled: the fixing nut is unscrewed and the friction washers are removed. Having removed the felt washer, it becomes clear why the protrusion is formed - it is too thick. As a replacement, you can pick up a thinner one made of plastic. After assembly, the protrusion disappears.

Unfortunately, it is not always possible to eliminate the breakdown that occurred during operation. For example, it is almost impossible to repair the overrunning clutch on your own. In this case, there remains a direct path to the workshop to the professionals. Of course, you will have to part with a certain amount of money, but repairs will be cheaper than buying a new coil.

Consider the advantages of repairing an inertia machine in a workshop:

• high-quality repair of any coil;
• availability of spare parts for almost all types of meat grinders;
• precise control of the main pair;
• lubrication is carried out with special oils.

No matter how much the angler wants to, however, trying to repair the reel, he can simply worsen the situation, not to mention the risk of leaving "extra" elements on the table after assembling the inertia wheel. Not in all cities, and even more so in small settlements, there are such masters. In this case, the coil can be sent by mail or by a transport company.

Repair and lubrication of a non-inertia reel with a bytrunner using the example of the Kosadaka DEFENDER V5 3000. As a preamble to my short article, I will quote myself from my previous posts.

“No one has a box with a coil assembly diagram. Kosadaka DEFENDER coil is not there by chance? Or what other model from the same manufacturer? I disassembled this reel with a baytranenner, there was time to collect it only the next day. Rather, I tried to collect. I couldn't. I suppose they have the same scheme. Nobody has it? Maybe the box is left? "

.

. . . . . . . . . . . . . . . . . . ... Reassemble in reverse order.

Most of the problems that arise during the operation of the reel and interfere with comfortable fishing, while enjoying fishing, can be quite easily fix it yourself.

Another way out is to trust the professionals by contacting a special workshop. Both the first and second options will allow you to avoid spending on the purchase of a new reel, continuing to fish with the old, familiar and favorite model.

Let's consider how to disassemble a spinning reel, how to assemble, repair spinning reels with our own hands, and also analyze the basic rules for caring for these rather complex devices.

And if you are also interested in finding out the device of the inertial coils or the choice of the baitcasting reel, then read our articles!

Spinning reel selection important point for successful fishing it becomes a pity if the reel quickly becomes unusable, but do not give up, because in most cases it can be repaired.

Before starting to disassemble the coil, it is better to wipe it with cotton wool soaked in water to clear it of dirt, sand and fish mucus.

When disassembling the coil mechanism, all the details of the mechanisms are worth lay out in order right to left or left to right. This will allow you to assemble the spinning reel without unnecessary problems.
The coil is disassembled in this order:

1. first of all it is necessary remove the nut friction brake and spool;
2. then washers and gearslocated under the spool;
3. the next step is unscrew the handle;
4. then disassemble the coil mechanism itself: unscrew the clamping nut with pliers or a wrench, remove the rotor;
5. then remove the shackle of the line and the mechanism that latches it, to disassemble the roller through which the fishing line passes;
6. unscrew the stopper bolt reverse stroke and remove the switch, unscrew the plug bolt and remove it;
7. remove the coil wall (as a rule, this requires quite a lot of effort);
8. removing the wall, you will see a slider and two gears - this is the main mechanism of the coilif everything is in order with them, you should not take them off.

As for the assembly of the coil, it is carried out in the reverse order.

Internal noise can be caused by dirt entering the mechanism or broken bearings or other parts. If there is noise, the use of a freewheel is necessary stop immediatelyso as not to make the problem worse. The coil should be disassembled and, depending on the specific cause of the problem, either cleaned or replaced with new parts.

If, during the reeling of the line, there is a rumble and knock, the mechanism periodically jams, and under load (while playing) the reel wedges, this means that there is serious problems in the final drive mechanism. In this case, the drive and driven gear must be replaced with a new pair.

If the bow of the line guide spontaneously switches from the “cast” position to the “rewind” position, this can lead to various problems - from shooting the bait to rod breakage.

To fix the problem, you first need to tighten the boltswith which the bow is attached. In the event that this was not enough, remove the cover, under which the spring is located, and add elasticity to herby installing a gasket on the rod, or change the spring to a more rigid one.

When this problem occurs, the spool handle can rotate freely both forward and backward even when the backstop is engaged. In modern models, the stopper is made on the basis of an overrunning clutch, and the cause of the problem is dirt and grease thickening. The coupling must be disassembled and lubricated with liquid oil. It should be noted that overrunning clutch repair is a rather complicated procedure, which is better to be entrusted to professionals.

The appearance of dents, scratches and other defects on the side of the spool leads to a decrease in the casting distance. In addition, the line is significantly injured by the unevenness of the spool, and its service life is significantly reduced. How to fix it? When such defects appear, they must be grind thoroughly, and polish the surface of the bobbin collar. At the same time, it is necessary to try not to remove the hard-alloy metal deposition from the side, which is present on good modern reels.

On reels with a front friction brake, the clutch retaining nut is located 1-2 mm above the spool edge... As a result, the line clings to it and falls under the edge, gets tangled and torn. To fix the problem, you should disassemble the mechanism: Remove the retaining nut and clutch washers, then replace the felt spacer with a thin plastic one. This will align the locking nut with the edge of the spool.

If a creak appears, it means that the coil is need to lubricate... At the same time, it can be difficult to determine which specific parts creak, so the best option when this problem appears is to disassemble, clean and lubricate the entire coil. With a certain skill, this will not be a problem and will not take much time.

If the line comes off in a tight spiral during casting, the reason is dirt ingress into the roller mechanism of the line laying machine. The bearing located there rubs, and the line twists. Accordingly, in order to eliminate the malfunction, it is necessary disassemble, clean and lubricate the roller.

If the line winds on the spool unevenly, resulting in a front or rear taper, it is not necessarily a disadvantage... However, you should know that the situation can be easily corrected in the right direction. There are several washers of different thicknesses on the main shaft of the reel. To eliminate line winding taper down, one washer should be removed, and if cone pointing up, the washer must be added.

Self-tightening of the friction clutch when blowing off the line - serious malfunction, which may be present on the reels of not the highest quality. It leads to a line break when playing fish and, in a more severe case, to breakage of the coil itself.
Unfortunately, it is almost impossible to eliminate this defect, the only way out is be careful when fishing.

There are many ways to increase your fish catch, but the most effective units are. Below the editors of the site share with you the 3 most effective ways to increase your catch:

1. Bite activator. It is a pheromone-based supplement that activates receptors in fish. ATTENTION! The Fishery Inspectorate wants to ban this bait!
2. Any other bait with flavors is less effective, it is better if they contain pheromones. But the most effective way is to use new for 2016 - DYNAMITE EFFECT!
3. Learning different fishing techniques. For example, here it is written about spinning wires.

In some cases, such as the overrunning clutch repair mentioned above, the process is complex and painstaking, so it is better to entrust this part to a professional. This will fix the problem. in a short time and with a professional guarantee.

In addition, do not forget that attempts to repair the spinning reel with your own hands can be very difficultMoreover, there is a risk of aggravating the problem.

So, let's take a closer look the advantages of repair by a specialist... Spinning reel repairman:

• can make fast and high-quality repair of spinning reels;
• has a large assortment of spare parts for spools of any class;
• can carry out high-precision adjustment of the main pair;
• uses special lubricating oils.

You can find such a master in any major city.

To prevent breakdowns and malfunctions, first of all, you should carefully transport the coil and handle it with sufficient care in the pond in order to avoid shocks that can lead to a breakdown of the mechanism, try not to dip it into water or put it on the sand.

Cleaning... If sand gets into the mechanism, moving parts such as the pinion and pinion can wear out rather quickly. To avoid this problem, you need to regularly disassemble the coil and clean it from the inside.

Grease... Dry operation of the mechanism is another reason for its rapid wear... Lubrication must be carried out immediately after cleaning the coil from the sand that has got into it. Which oil to use is not as simple as it might seem at first glance.

If this is not possible, you can use any oil that is suitable in consistency, but you need to be sure that it does not contain unnecessary additives and does not destroy plastic parts that are widely used in the production of modern spinning reels. In other words, an oil designed to soften metal-to-metal friction - not the best option.

Careful handling of the coil and regular maintenance will help to avoid serious problems. All malfunctions manifest themselves in one way or another at an early stage, it is on it that these malfunctions are easiest to eliminate. Timely maintenance and repairs will maximize the life of the reel, and it will delight the angler with flawless performance for years to come.

And if you want to gain knowledge on how to install and set up a spinning reel? Read this article.

At the end of the video - the elimination of the self-discharge of the line laying machine on the spinning reel. Happy viewing!

Fishing gives pleasure with its process - each of us knows about it. But in addition to this, we always want to get the result from fishing - to catch not three perches, but a dozen kilogram pikes - this will be the catch! Each of us dreams of this, but not everyone knows how.

A good catch can be achieved (and we both know this) thanks to good bait... It can be made at home or bought at fishermen's shops. But in stores it is expensive, and to prepare groundbait at home, you need to spend a lot of time, and, in all fairness, homemade bait does not always work well.

Do you know that disappointment when you bought groundbait or cooked it at home, but caught three or four perches? Of course familiar. So maybe it's time to use a really working product, the effectiveness of which has been proven both scientifically and by practice on the rivers and ponds of Russia?

There is such a bait and it's not a myth - TWITCHING LURE... Yes, yes, it was she. Many people know her, many love her, but only a few know how to use it, which is why there are so many angry reviews about her on the Internet. Someone simply does not know how to read the instructions.

Of course, it's better to try once than hear a thousand times. Moreover, now is the season! A 50% discount when ordering is a great bonus!

Order TWITCHING LURE soon!

Considering the conditions in which the spinning coils are operated - river sand, water or mud - the mechanism can be subject to various malfunctions. Falling into the water also has a negative effect on the operation of the fishing device: it is necessary to change the lubricant in it, as abrasive substances in the water can damage the parts. Various breakdowns can be associated with some features of the device of the coils of individual companies, and, of course, the duration of operation depends on the quality of the selected coil.

This guide will guide you through basic service of your coil, identifying and fixing the most common problems.

The main rule when disassembling, especially if you are doing this for the first time: put all the parts of the mechanism to be removed in order, from left to right. So when assembling you will not get confused and assemble it correctly.

Before disassembling the coil, thoroughly wipe it from dirt, sand and fish mucus with a cotton pad moistened with warm water. For stubborn dirt, you can add a little liquid soap to the water. Use tweezers or a cotton swab to remove dirt in hard-to-reach places. Do not use harsh household cleaners. If the surface cannot be cleaned with soap, you can remove the dirt with alcohol or gasoline. Neglecting the external cleaning step will make it difficult to disassemble the coil.

The coil assembly is carried out in the reverse order, in addition, it is necessary to constantly check the correctness of the installation of the parts during the process.

Depending on the type of coil and its design features, problems may arise during operation, some of which are easy to fix on your own. Let's consider the principles of configuration in more detail: