DIY nespresso coffee machine repair

In detail: do-it-yourself nespresso coffee machine repair from a real master for the site my.housecope.com.

How can you save on capsules for your Nespresso machine and drink your favorite coffee inexpensively?
Solution Yes:
Buy reusable capsules!
You can buy with a discount here:
You can buy for the promotion here:

How do refillable capsules for a Nespresso coffee machine work?

You can buy with a discount here:
You can buy for the promotion here:

The original Nespresso capsules consist of a foil-sealed aluminum container. It's really just a container of ground coffee, hermetically sealed.
Nespresso system capsules work as follows: water is fed through the bottom of the container and exits through the lid.
One part of the coffee machine mechanism, for example a Delongi Nespresso with a capsule recess, is located in the piston, with which the user clamps the capsule using an external lever. In this case, the pointed petals pierce the bottom of the container, forming holes through which hot water is supplied under pressure. And the capsule lid is pressed against the supporting element shown on the right with a complex surface relief. At some point, the pressure reaches a level at which the protrusions on the support element pierce the foil of the capsule lid, after which the coffee begins to flow further into the cup.

Now let's look at how the mechanism of the same Delongy coffee machine works in the case of a reusable capsule for the Nespresso system using the example of a plastic capsule.

You can buy with a discount here:
You can buy for the promotion here:

Video (click to play).

When the capsule is clamped using an external lever, the pointed petals enter a special recess of the reusable capsule and do not touch the capsule itself. Pressurized water holes are already made in the reusable capsule body, both on the side of the pointed petals and on the side of the capsule lid.
Please note that the holes on the lid of our reusable capsules are made in a special way in the form of a special stainless steel mesh, which ensures a natural flow of the finished drink and at the same time there is a high-quality filtration from the swollen particles of ground coffee.

You can buy with a discount here:
You can buy for the promotion here:

It must be emphasized that the form factor of the refillable capsules is exactly the same as the original Nespresso capsules. The use of reusable capsules of our online store completely eliminates any malfunctions of the coffee machine.
Buy our refillable capsules and enjoy delicious and cheap coffee from your Nespresso coffee machines!

You can buy with a discount here:
You can buy for the promotion here:

Video repair of capsule coffee machines nespresso channel egorkin dima

What is a good and high-quality coffee machine for? Of course, for aromatic hot coffee in the morning. The brewing process of this wonderful drink is almost completely automated and requires minimal human intervention. The filling of the device implies the presence of many mechanical parts, electronic circuits, as well as a miniature hydraulic system. However, everything soon fails and these necessary devices are no exception. In the event of a breakdown of coffee machines, there are only two options: take it to the service or repair the coffee machine yourself.

Water supply interrupted. There is a blockage in the pipeline of the mechanism;
The coffee has acquired an unusual smell or taste. In this case, it is not always necessary to fix something with your own hands. Perhaps you just need to change the coffee tablets, and there is a very wide selection of them: Dolce Gusto - Dolce Gusto, Nestlé, Jacobs, etc. Alternatively, the filter of the coffee machine may be clogged.Cheap plastic can be another factor affecting the taste and smell of coffee. During operation, some parts of the machine heat up to 130 degrees, which can cause the plastic to melt;
Cold coffee. Most likely, your heating element has stopped working;
The espresso machine is not working. Many factors can affect this: the motor is broken, the pump does not work, the power cable is broken;
Water dosage exceeded (most often found in capsule coffee machines). Most likely, the breakdown lies in the engine or in the timer circuit.
The brewing time setting circuit does not work or the dosage into the cup is incorrectly adjusted. Of course, you need to focus on the model of the device and its brand, but a common reason is the improper operation of the engine control circuit, or one of its compartments.

If you are not sure that the repair of the coffee machine is within your power, then it is better to refer it to specialists. If the device is under warranty, then it is not worth disassembling it at all, it will instantly lose the warranty.

To repair the coffee machine, first you need to disassemble it. And how to do it correctly, step by step is described below.

It is necessary to find the back wall of the device, or rather the set screws. Unscrew with a screwdriver, pliers or whatever is at hand and is ideal for such work, set aside. It is worth noting that there may be several options for screws. They can be hidden, cruciform, or with a convex head;
The screws are removed, it is logical that the cover should be easily removed. However, if it cannot be removed, then there are hidden locks in the case. Most often these are ordinary plastic latches and they are located at the bottom of the back cover. From the outside, such a lock can be easily opened with a knife or a small screwdriver;
Finally, access to the "insides" of the machine has been obtained, it's time to start repairing it.

And so let's go in order. There is a blockage in the water supply pipe. In such coffee machines as: Delongee, Bork - Bork, Ariete - Ariete and others, cleaning is done using a long and thin rubber hose. It must be run along the duct and thereby break through the blockage. However, it will be much more effective to use special brushes on a flexible leg.

It is a little more difficult to clean the filter with your own hands. With frequent use of the coffee machine, the filter accumulates: scale, coffee residues, salt plugs, etc. Cleaning must be approached carefully, but the most important thing is to do it according to the instructions, otherwise you can violate the integrity of the part. In the process, it is allowed to use a soft swab sprinkled with alcohol. Rinse the filter thoroughly after cleaning.

If you are unable to solve the problem yourself, contact a Saeco espresso machine repair center.

The coffee machines of the firms Mulinex, Krups, Roventa, Saeko have another problem - water leaks. In them, the valve regulating the water supply is located practically in the filter. If the coffee does not stop pouring, most likely a worn valve is to blame, which leads to this phenomenon.

The valve cannot be repaired; in this case, only replacement with another new part is available. To understand whether the valve has broken, it is enough to pour coffee out of the machine, disassemble, rinse and inspect well for possible breakdown.

Initially, it is worth checking if everything is in order with the power supply. See if the cable is broken, check the grounding.
It also happens that household coffee machines produced in China simply lose contacts (they go away). Such cases were encountered with more famous brands: zauber, melitta, trevi. It is enough to check all the wire connections with the control circuit.
A common case for Senseo¸Siemens, Ufesa machines, they have low-quality thermostats built into them. To diagnose it, you need to remove one wire from its end and "ring" the contacts with a tester. If all is well, then the chain will be closed.
The heating element may also fail. Diagnostics is carried out in the same way as a thermostat.Replacing it with a new one is difficult, it will be easier to try to repair or buy a new coffee machine.
Very often, on the shelves next to the coffee machine, all the necessary accessories are sold that you will certainly need for the correct operation of the device. And for cleaning technical parts, it is definitely advised to buy special flexible brushes.

The principle of operation and repair of capsule coffee machines is slightly different from drip coffee machines. A small container of coffee powder is attached to the inside of the machine, the piercing mechanism is manually clamped. After use, the capsule is disposed of. Inside such devices, most often there are no temperature sensors, but there is an ordinary pump that runs on a timer. The water flow rate has been calculated in advance. If the water supply is carried out with the wrong dosage, then the time supply circuit may have broken.

Repair of coffee makers often does not depend on the brand or model; in general, they differ only in nuances. This can be the shape, as well as the location of parts, size, different types of sensors. The very principle of operation of the coffee machine does not change.

Any professional inspection for breakage always starts with the cord. It makes no difference whether it is a capsule or drip coffee machine repair. Then the power board is checked (if any), it is worth noting that the coffee machine has a lot of filters, diode bridges, and also transistors. All this must be inspected for burnout. This is the only way to recognize the true cause of the equipment malfunctioning.

The repair of Saeco coffee makers was discussed, they described what would break. The speech concerned coffee machines that can grind grain, dose, brew, pour into cups. The difference between the coffee maker is in its modest capabilities, there are plenty of designs. More often we find three on the counter: drip, espresso, capsule. There are quite large differences between them in the methods of cooking, the insides are similar. Each device has one 230 volt motor (for example, synchronous with a magnetized rotor) that drives the pump. More like a compressor, in some the piston goes back and forth. Creates high pressure (horn modifications). Consider how to repair a coffee maker with your own hands.

At the coffee maker, a container for water and a heating element form the basis, but there are further differences. The difference between a drip coffee maker and an espresso machine is described by the operating pressure. In the first case, boiling water simply drips onto the filter containing the poured coffee, the drink seeps further down, flows down, fills the cup. It is important to see the drop-stop function so as not to constantly collect moisture. In an espresso, a jet of water with a temperature of 95 degrees is thrown under pressure, forced through the tablet. To top it off, a special press drains the pomace. It turns out a dry squeezed coffee tablet. No additional filter needs to be installed. Coffee machines work on different principles, there are drip, espresso models.

Capsule coffee makers contain an infusion compartment with a needle, into which a plastic container of coffee powder is inserted. Brewing can be carried out under pressure or without. The first method differs from the second by the presence of a boiler in the design: water gains the required temperature, the compressor creates pressure. In the latter case, we often observe the possibility of obtaining milk froth. Stable bubbles are generated by the high temperature steam. The walls of the balls are cured by strong heat. One difference between brewing coffee and getting creamed:

Coffee is brewed with water of 95 degrees Celsius, to obtain steam, the heating elements work, reaching a threshold of 127 degrees. The modes are considered the best for traditional recipes.

Pay attention to the compressor: it allows you to brew coffee correctly, to get froth. The generated pressure is impressive, reaching 15 - 20 bar, more than is supplied to the heating system in the fall, checking during the period of technical measures. Managed to brew high quality coffee.In models of espresso (sometimes called carob), a special horn where coffee is applied. Then the structure is screwed onto the housing branch pipe, the handles are tightened with force. It turns out a dense tablet through which water is powerless to flow, having lost the circuit of a high-power compressor. It is possible to brew excellent coffee, not much different from the true drink obtained by the Turks according to generally accepted, traditional methods.

We describe in detail the device of a coffee maker, a variety of coffee makers, so that readers can imagine what is happening inside. Knowing the features of the functioning of the devices, it is easy to localize the breakdown. The main types of malfunctions will visit the mind automatically, the internal structure will become apparent.

We are writing the work of a drip coffee maker. Water is taken in by a container through a hose, pumped out by a pump. The flow heater delivers a fixed power, the pump speed is matched to the output temperature. Smart coffee makers have a sensor that monitors the parameters of the environment. By passing the pipe, the hot water reaches the upper compartment, which is equipped with a filter and contains ground coffee. The dosage is carried out according to the readings of the flow meter, or a temporary pump relay limits the duration of the heating element activation. Adjustment is possible. The spring timer works by feeding the pump through the spark extinguishing relay, or the electronic board monitors the flow meter readings, stopping the water supply at the right time.

In some cases, the temperature is not monitored at all. A portion is taken through a check valve. Then the heating element in a matter of seconds turns the liquid into steam, the jet rushes up the tube, filling the infusion compartment, and flows into the cup. The technique will not allow you to get true coffee, it is attractive for its simplicity of implementation. The coffee maker knows how many micro doses one cup can hold. The simplest manual counter controls the operation. The absence of water in the pipe for a new intake is controlled by a bimetallic plate. In the simplest case, the heating element immediately works on a volume of water equal to a standard cup of coffee.

The drip coffee maker has an hourglass-like shape; it is powerless to make cappuccino froth, latte. Self-repair of drip coffee makers is simple. Inside we will find:

a heating element;
water pump;
control scheme.

There is an electronic filling of the microcircuits - there is a pulsed power supply that generates a constant voltage of the required rating (+5, +12 V). The efficiency is increased. To measure temperature, a bimetallic plate is used, which rarely breaks. The check valve can be easily checked by blowing in one direction or the other. The engine is running, controlled by a time relay (ordinary RC circuit), less often we see a flow meter, a level sensor. The pump rings, if the engine is collector, the action is repeated for the sections one by one.

Repairing a carob coffee maker seems to be the most difficult. There is not a pump - a compressor that pumps water under pressure into the boiler. The heater is located outside the tank. Outwardly, it resembles an iron: the heating element is bolted to the wall of a collapsible boiler. To regulate the temperature, there is a bimetallic plate, the sensor tension is adjusted with a screw for at least two positions. For brewing coffee, a temperature of 95 degrees Celsius is used, getting steam will require 127 degrees. Accordingly, the relay contact of the heating element opens at the right time. The boiler is durable, assembled in two halves, withstands a pressure of 20 atm without problems. The inlet is equipped with a check valve so that water does not go back during thermal expansion, heating.

The engine is made to dispense a fixed portion of water. The espresso maker is named after the coffee is poured into a long-handled cup. The tension design is put on the body, the coffee is rammed. Under the pressure generated by the pump, water fills the mug.Coffee makers are considered the best, experts say: carob models will allow you to take the maximum taste and aroma from the beans.

Inside the carob coffee makers, one motor belongs to the pump. Switching the path to steam supply is carried out manually. A collector motor is rarely used, the pump is relatively small, the point of fencing a garden disappears, there is a lot of noise. The pressure is generated by a piston (like a refrigeration compressor), which does not require much effort to develop. It is easier to save copper, use an induction motor. Brushes take up a lot of space. Carob-type coffee makers are equipped with power supplies for the engine and other elements.

Expensive models contain a motor compatible with inverter control. There are valves. A feature of the carob models is the presence of a boiler bypass valve. The pressure is dosed to ensure the correct brewing process.

Capsule coffee makers differ little from drip coffee makers. A small container containing coffee powder is installed inside, the piercing mechanism is manually clamped. After use, the capsule is ejected automatically, removed by the user of the device. Inside, the pump controls the flow of liquid, the instantaneous water heater raises the water temperature, reaching the set one. Sometimes there are no sensors, just the pump operates according to a timer. The water flow rate has been calculated in advance. It remains to substitute the cup. If water is not dosed correctly, we are looking for a power source for the pump motor. The timing circuit is faulty, no matter how the interval is set.

Do-it-yourself coffee maker repair does not depend too much on the model. Saeko, Gaggia, Nespresso, Rowenta, Spidem - they differ in details. Shape, arrangement of parts, types of sensors. The principle of operation remains the same everywhere. Repairing Jura coffee machines is similar to repairing Krups coffee machines.Inspection begins along the cord along the power board, if any. The switching source is equipped with a cascade of filters, a diode bridge, and key transistors. Elements before and after the transformer are inspected for burnout, ringing. It's easier to immediately measure the output voltage of the circuit, then move on. It is easier to check the pump separately. Before that, look at the voltage rating required for the power supply in order to avoid an incident. In the event of a pump breakdown, the possibility of winding the stator coils is assessed. There is a chance to successfully complete the operation, you will not have to buy a new part.Most of the problems arise due to the fact that a modern coffee brewing machine is an extremely technological device, the operating parameters of which are precisely calculated. Therefore, any violation, whether it is hard water, capsules not recommended by the manufacturer, or other grinding of grains, necessitates repairing the apparatus or understanding how high-pressure systems work. But most of the simple problems can be fixed at home as well. Consider how to repair a coffee maker with your own hands.If it is decided to independently investigate the coffee maker and carry out repairs, then it is worth taking basic safety measures:

The device must be disconnected from the network.

You need to work with a tool with insulated handles.

Water and wet hands are potential hazards.

Disassembling the body of most coffee makers is not difficult. Often it is enough to unscrew a few screws on the back cover. This makes it possible to gradually disassemble the device into units or large parts. At the same time, there are subtleties: in Delongy's cars, the bolts located on the lower part are closed with plugs or are under the rubber feet, and many Saeko models additionally require the removal of fasteners to remove individual blocks that open access to the areas needed for repair.

Vitek VT1513 Coffee Maker Pump

To carry out maintenance or repairs, you must first disassemble the device:

The top aluminum lid is removed where the cups are located.
The fastening screws hidden under the rubber pads are found.
Self-tapping screws are removed, the back cover is removed, giving access to all nodes.

Potential breakage areas can be seen immediately. High pressure tubing - hard, thin. The feed selector is a small plastic block that the distributors fit into. The blower is a round metal pump. To repair the Vitek coffee maker you will need:

Assess the condition of the high-pressure pipes, check the places of their fixation - there should be no looseness, cracks.
Check the condition of the blower housing. Splits or traces of overheating indicate a possible pump malfunction.
Inspect the condition of the feed switch.

If, after assessing the reliability of contacts, the problem is still not clear, carry out the following operations:

Clean the high pressure pipes. For this, you can use thin rubber tubes or a single-core wire with soft insulation. There is also a special tool - a flexible brush.

Check fasteners and contacts, remove all dirt.

Clean the filters.

After that, the coffee maker starts up and is re-checked for the operability of the nodes. By the way, the most common accident is crack in switch, it is determined by the presence of water on the surface of the part. The damage cannot be sealed (pressure will squeeze out any sealant). Therefore, it is worth replacing the block or simply melting the crack, heating a knife or screwdriver on the gas burner. Image - DIY nespresso coffee machine repair

Breakage of the Vitek VT1513 mode switch

If disassembly, cleaning, visual inspection of the coffee maker did not allow to localize the problem, most likely, the matter is in the blower, and it is necessary to call a specialist.

There are many common breakdowns. It is not difficult to repair them with your own hands. For instance:

clogged filter

Oxidation of contacts became more and more common, as manufacturers began to save every penny in production. Obligatory cleaning and regular checking of contacts is the key to the successful operation of the coffee maker.

Failure of the heating element... Repairs in this case must be carried out by a specialist. Since there are models of coffee makers, the heating element of which cannot be dismantled without damaging other parts. The cost of work and the purchase of a new spare part will cost more than a new device.

The main part of the repair is a thorough cleaning of all nodes and contact groups. Without carrying out this operation, there can be no question of any thorough testing of the electrical parameters of motors, temperature sensors, electronic units.These actions will be ineffective to say the least.

Each coffee maker comes with an instruction manual. It describes the typical problems of a particular model and provides ready-made recipes for solving them. Often these are instructions like "the coffee maker won't turn on - check the wire." Yes, the integrity of the power cable, the absence of scuffs, fractures, mechanical damage - this must be checked without fail.

However, the general principle of repair is reduced to moving from simple to complex. Something does not turn on - the functionality of the button is checked, the cleanliness and reliability of the contact. The operating parameters do not correspond to the expected - the regulators and sensors are closely examined, cleaned, lubricated, if necessary, replaced. To eliminate common malfunctions of coffee makers, you need to act on the principle of a thorough examination of parts for damage, full service of all filters, pipes, contact groups and sensors.A coffee maker is an indispensable device in modern life, but the complexity of its device implies strict adherence to the manufacturer's recommendations. In order to constantly enjoy a fragrant drink, use coffee of the correct grinding, a certain type of capsule, and also periodically service the machine.Any electrical device can fail over time. Repairing coffee makers from Delonghi, Saeco or Krups is quite easy to do with your own hands. These kitchen appliances are considered one of the easiest to repair and operate.Before you start repairing the device, you need to determine what exactly broke in it. This will greatly speed up and simplify the repair process. There are two types of coffee machines:Their main difference is the working pressure. In drip coffee makers (Bosch - Bosch, Zelmer - Zelmer, Vitek - Vitek) hot water drips through the coffee filter, through which it passes into the cup, already being a fragrant drink. In an espresso, a stream of boiling water is poured into the cup, passing through a coffee tablet (compressed ground natural coffee). The advantage of using espresso machines - Electrolux, Binatone, Braun, Philips (Philips) and many others - is that they can work without a filter. Image - DIY nespresso coffee machine repair

Photo - espresso

Capsule coffee machines for brewing coffee have a special container into which ground natural powder is poured. This allows brewing a drink with or without pressure. The key difference between these functions is that with professional espresso machines, you can make a frothy coffee.

Photo - kapelnaya

Main problems coffee machines and coffee makers of domestic and professional type:

The water stopped flowing. Most likely, one of the pipes supplying water was simply clogged;
The coffee began to give off a strange smell or taste. In this case, it is not always necessary to repair the coffee makers yourself, perhaps you just changed the coffee tablets (they are Dolce Gusto - Dolce Gusto, Nestlé, Jacobs, etc.). Another reason can be a clogged filter or cheap material for the device. If the optimum water temperature for brewing coffee is 95 degrees, then the internal parts are heated to 125 and above. As a result, the cheap plastic can start to melt, imparting its taste to the drink;
Cold coffee. The heating element stopped working;
Incorrect dosage of water (found in capsule coffee makers). A breakdown can occur both in the engine and in the timer circuit;
The espresso machine does not turn on. There may be several reasons: breakdown of the engine, pump, problems with the power cord;
You cannot set the brewing or filling time of the cup. Depending on the type of coffee maker, this may be a breakdown of the time relay, control circuit, engine (or one of its compartments).

It is worth noting that after the intervention, warranty repairs will no longer be provided, so if you are not confident in your abilities, it is better to contact the branded service center.

Photo - schematic diagram

In order to repair any coffee makers (Nespresso - Nespresso, Delongy), you will need to disassemble them first. Step-by-step instructions on how to do this:

There are set screws on the back of the coffee machine. They need to be untwisted and put aside. They can be of several types: hidden, cruciform and cone-shaped (often found in Indesite). They are removed with a screwdriver, pliers or other suitable tools;
If, after removing the screws, the case is not retracted, then it is secured with hidden locks. The latches are located at the bottom of the rear panel. They cannot be opened from the outside, so you have to pry them with a knife or screwdriver;
After removing the case, you can start repair work.

If the pipe is clogged at Delongey, Bork - Bork, Ariete - Ariete or other coffee makers, then you need to use a long thin rubber hose for repairs. It starts up along the duct and breaks through the blockage. Sometimes for such purposes, special brushes with a flexible leg are used, they allow you to clean the pipe and remove not only coffee, but also mineral deposits.

Photo - construction

Cleaning the filter is a little more difficult. With frequent use, various debris accumulates on it: salt plugs, coffee dust, scale. It should be cleaned only according to the instructions, since otherwise, the integrity of the spare part may be damaged. In most cases, it is allowed to wipe it with a swab dipped in alcohol or other degreaser. Rinse the part thoroughly after rinsing.

Photo - filter

Also, problems can be associated with the filter if water leaks from the coffee maker. This is often found in machines manufactured by Moulinex, Krups, Rowenta, Saego. A special valve is installed near the filter, which, after turning off the timer, turns off the water supply. If after a certain time the drink has not stopped flowing, then the cause is a malfunction of this element. The valve may wear out after frequent use, or it may simply not be able to handle the accumulated amount of coffee. To check and fix the breakdown, you need to disassemble the coffee machine, pour the coffee out of it and inspect the valve. Please note that it cannot be repaired, so the part changes immediately.

Photo - disassembly

If the coffee maker Redmond, Spidem, Tefal, Siemens and others does not turn on, then urgent repair is required:

The first step is to check the power wire. It needs to be examined for an open circuit, and also to additionally check the grounding. It connects to the terminal block, so be careful when diagnosing;
Sometimes, household coffee machines made in China simply lose contacts. It also occurs in professional models (zauber, melitta, trevi). In this case, you need to check all the places where the wires are connected to the control circuit;
Many modern cars (Senseo¸Siemens, Ufesa) sin with a low-quality thermostat. To diagnose it, you need to remove one wire from its end and check the contacts with a tester. With a serviceable element, the circuit must be closed;
Also, the coffee maker may not turn on if the heating element needs repair. It is called in the same way as a thermostat. For many models (Jura Impressa, Miele, Gaggia, Butler) it is made in the form of a disk, so it will be rather difficult to change it, it is easier to try to repair a part or buy a new car;
There are also certain secrets to cleaning the engine. In the care products departments, special brushes are sold that will help clean different parts of the motor without damaging the fragile material. It should be noted that in AEG, Solis or Unit coffee makers, the motor has several compartments, each of which is cleaned separately.

Video: Delonghi Coffee Maker Repair

Very interesting to read: To enjoy hot and aromatic coffee every morning, you will definitely need a good quality coffee machine. The process of brewing coffee using capsule coffee machines is practically fully automated and does not require a lot of steps from you.As with any technology, a capsule coffee machine may require replacement or repair of mechanical parts or electronic circuits. The best option to restore the working capacity of such coffee machines as Nespresso, Delongi, Krups is to do it yourself.Despite the fact that capsule coffee machines Nespresso, Delongy, Krups, Dolce have a high degree of wear, nevertheless, they may also need to be repaired. The main causes of malfunctions are:

Poor water quality.

Voltage drops.

Scale appearing.

Nespresso Essenza coffee machineMalfunctions that occur when using capsule coffee machines Nespresso, Delongi, Krups can be roughly divided into two main types:

Malfunctions that can be repaired by hand without the use of special tools and devices.

Malfunctions that need to be repaired with the assistance of a specialist.

Important: do not try to carry out repairs yourself related to the replacement of wires, supply systems or water heating. This can harm your health and increase the cost of restoring your coffee machine.If, during the preparation of coffee, the pressure of the jet drops out or there is a hissing sound from the horn, this may be due to the formation of limescale. This problem is not critical and can be fixed by yourself. To eliminate, you need a thin wire or needle. Clean the diffuser opening (the part from which water enters the capsule). To prevent this problem from recurring, use distilled water.This flow is possible in the place where the connecting seal is located. The most common reason for clogging the seal in capsule coffee machines Nespresso, Delongy, Krups, Dolce is densely

Pieces of coffee.

Body fat.

Foreign objects.

Remove the seal to correct the problem. It can be removed easily, without any pressure, it is enough to gently push the seal back with a screwdriver or not a sharp knife. Depending on the brand of capsule coffee machine (Nespresso, Delongy, Krups, Dolce thickly), the seal can be protected by a mesh, it must also be unscrewed. Use special detergents to remove various particles and foreign deposits. If the mesh or the seal itself is damaged, then they cannot be repaired and must be replaced with new ones.Nespresso Inissia coffee machineThis problem can occur if the mesh or filter of the coffee machine is clogged with large pieces of coffee beans, limescale or fat deposits. To eliminate all blockages, it is necessary to thoroughly rinse all parts using a hard sponge.Important: when clearing blockages and various deposits, do not scratch metal parts, this may further lead to more frequent blockages or malfunction of the device.The coffee machine does not brew coffee, there is an abnormal noiseFirst, check the presence of water in the tank and the fact of its heating. If the water is heated and supplied without problems, then use the cappuccino maker and run the water through it. If the problem was the formation of an air lock, then this will help you fix it.Another reason for a thin and weak jet of water can be a blockage in the tubing system. Depending on the model and manufacturer of the coffee machine (Nespresso, Delongi, Krups), the rinsing sequence may differ. You must carefully read the sequence of actions in the instructions.Not all models of capsule coffee machines have the function of reminding you to clean the machine. However, remember that any technique requires maintenance and do not forget to take preventive measures to avoid further repairs.

Video (click to play).

Most of the breakdowns in the operation of capsule coffee machines Nespresso, Delongy, Krups, Dolce can be easily eliminated by yourself.To do this, you need to clearly define the problem that has arisen, and all actions must be rational and careful.