Do-it-yourself bork c800 coffee maker repair

In detail: do-it-yourself bork c800 coffee maker repair from a real master for the site my.housecope.com.

What is a good and high-quality coffee machine for? Of course, for aromatic hot coffee in the morning. The brewing process of this wonderful drink is almost completely automated and requires minimal human intervention. The filling of the device implies the presence of many mechanical parts, electronic circuits, as well as a miniature hydraulic system. However, everything soon fails and these necessary devices are no exception. In the event of a breakdown of coffee machines, there are only two options: take it to the service or repair the coffee machine yourself.

Water supply interrupted. There is a blockage in the pipeline of the mechanism;
The coffee has acquired an unusual smell or taste. In this case, it is not always necessary to fix something with your own hands. Perhaps you just need to change the coffee tablets, and there is a very wide selection of them: Dolce Gusto - Dolce Gusto, Nestlé, Jacobs, etc. Alternatively, the filter of the coffee machine may be clogged. Cheap plastic can be another factor affecting the taste and smell of coffee. During operation, some parts of the machine heat up to 130 degrees, which can cause the plastic to melt;
Cold coffee. Most likely, your heating element has stopped working;
The espresso machine is not working. Many factors can affect this: the motor is broken, the pump does not work, the power cable is broken;
Water dosage exceeded (most often found in capsule coffee machines). Most likely, the breakdown lies in the engine or in the timer circuit.
The brewing time setting circuit does not work or the dosage into the cup is incorrectly adjusted. Of course, you need to focus on the model of the device and its brand, but a common reason is the improper operation of the engine control circuit, or one of its compartments.

Video (click to play).

If you are not sure that the repair of the coffee machine is within your power, then it is better to refer it to specialists. If the device is under warranty, then it is not worth disassembling it at all, it will instantly lose the warranty.

To repair the coffee machine, first you need to disassemble it. And how to do it correctly, step by step is described below.

It is necessary to find the back wall of the device, or rather the set screws. Unscrew with a screwdriver, pliers or whatever is at hand and is ideal for such work, set aside. It is worth noting that there may be several options for screws. They can be hidden, cruciform, or with a convex head;
The screws are removed, it is logical that the cover should be easily removed. However, if it cannot be removed, then there are hidden locks in the case. Most often these are ordinary plastic latches and they are located at the bottom of the back cover. From the outside, such a lock can be easily opened with a knife or a small screwdriver;
Finally, access to the "insides" of the machine has been obtained, it's time to start repairing it.

And so let's go in order. There is a blockage in the water supply pipe. In such coffee machines as: Delongee, Bork - Bork, Ariete - Ariete and others, cleaning is done using a long and thin rubber hose. It must be run along the duct and thereby break through the blockage. However, it will be much more effective to use special brushes on a flexible leg.

It is a little more difficult to clean the filter with your own hands. With frequent use of the coffee machine, the filter accumulates: scale, coffee residues, salt plugs, etc. Cleaning must be approached carefully, but the most important thing is to do it according to the instructions, otherwise you can violate the integrity of the part. In the process, it is allowed to use a soft swab sprinkled with alcohol. Rinse the filter thoroughly after cleaning.

If you are unable to solve the problem yourself, contact a Saeco espresso machine repair center.

The coffee machines of the firms Mulinex, Krups, Roventa, Saeko have another problem - water leaks. In them, the valve regulating the water supply is located practically in the filter. If the coffee does not stop pouring, most likely a worn valve is to blame, which leads to this phenomenon.

The valve cannot be repaired; in this case, only replacement with another new part is available. To understand whether the valve has broken, it is enough to pour coffee out of the machine, disassemble, rinse and inspect well for possible breakdown.

Initially, it is worth checking if everything is in order with the power supply. See if the cable is broken, check the grounding.
It also happens that household coffee machines produced in China simply lose contacts (they go away). Such cases were encountered with more famous brands: zauber, melitta, trevi. It is enough to check all the wire connections with the control circuit.
A common case for Senseo¸Siemens, Ufesa machines, they have low-quality thermostats built into them. To diagnose it, you need to remove one wire from its end and "ring" the contacts with a tester. If all is well, then the chain will be closed.
The heating element may also fail. Diagnostics is carried out in the same way as a thermostat. Replacing it with a new one is difficult, it will be easier to try to repair or buy a new coffee machine.
Very often, on the shelves next to the coffee machine, all the necessary accessories are sold that you will certainly need for the correct operation of the device. And for cleaning technical parts, it is definitely advised to buy special flexible brushes.

The principle of operation and repair of capsule coffee machines is slightly different from drip coffee machines. A small container of coffee powder is attached to the inside of the machine, the piercing mechanism is manually clamped. After use, the capsule is disposed of. Inside such devices, most often there are no temperature sensors, but there is an ordinary pump that runs on a timer. The water flow rate has been calculated in advance. If the water supply is carried out with the wrong dosage, then the time supply circuit may have broken.

Repair of coffee makers often does not depend on the brand or model; in general, they differ only in nuances. This can be the shape, as well as the location of parts, size, different types of sensors. The very principle of operation of the coffee machine does not change.

Any professional inspection for breakage always starts with the cord. It makes no difference whether it is a capsule or drip coffee machine repair. Then the power board is checked (if any), it is worth noting that the coffee machine has a lot of filters, diode bridges, and also transistors. All this must be inspected for burnout. This is the only way to recognize the true cause of the equipment malfunctioning.

Any electrical device can fail over time. Repairing coffee makers from Delonghi, Saeco or Krups is quite easy to do with your own hands. These kitchen appliances are considered one of the easiest to repair and operate.

Before you start repairing the device, you need to determine what exactly broke in it. This will greatly speed up and simplify the repair process. There are two types of coffee machines:

Their main difference is the working pressure. In drip coffee makers (Bosch - Bosch, Zelmer - Zelmer, Vitek - Vitek) hot water drips through the coffee filter, through which it passes into the cup, already being a fragrant drink. In an espresso, a stream of boiling water is poured into the cup, passing through a coffee tablet (compressed ground natural coffee). The advantage of using espresso machines - Electrolux, Binatone, Braun, Philips (Philips) and many others - is that they can work without a filter.

Photo - espresso

Capsule coffee machines for brewing coffee have a special container into which ground natural powder is poured. This allows brewing a drink with or without pressure.The key difference between these functions is that with professional espresso machines, you can make a frothy coffee.

Photo - kapelnaya

Main problems coffee machines and coffee makers of domestic and professional type:

The water stopped flowing. Most likely, one of the pipes supplying water was simply clogged;
The coffee began to give off a strange smell or taste. In this case, it is not always necessary to repair the coffee makers yourself, perhaps you just changed the coffee tablets (they are Dolce Gusto - Dolce Gusto, Nestlé, Jacobs, etc.). Another reason can be a clogged filter or cheap material for the device. If the optimum water temperature for brewing coffee is 95 degrees, then the internal parts are heated to 125 and above. As a result, the cheap plastic can start to melt, imparting its taste to the drink;
Cold coffee. The heating element stopped working;
Incorrect dosage of water (found in capsule coffee makers). A breakdown can occur both in the engine and in the timer circuit;
The espresso machine does not turn on. There may be several reasons: breakdown of the engine, pump, problems with the power cord;
You cannot set the brewing or filling time of the cup. Depending on the type of coffee maker, this may be a breakdown of the time relay, control circuit, engine (or one of its compartments).

It is worth noting that after the intervention, warranty repairs will no longer be provided, so if you are not confident in your abilities, it is better to contact the branded service center.

Photo - schematic diagram

In order to repair any coffee makers (Nespresso - Nespresso, Delongy), you will need to disassemble them first. Step-by-step instructions on how to do this:

There are set screws on the back of the coffee machine. They need to be untwisted and put aside. They can be of several types: hidden, cruciform and cone-shaped (often found in Indesite). They are removed with a screwdriver, pliers or other suitable tools;
If, after removing the screws, the case is not retracted, then it is secured with hidden locks. The latches are located at the bottom of the rear panel. They cannot be opened from the outside, so you have to pry them with a knife or screwdriver;
After removing the case, you can start repair work.

If the pipe is clogged at Delongey, Bork - Bork, Ariete - Ariete or other coffee makers, then you need to use a long thin rubber hose for repairs. It starts up along the duct and breaks through the blockage. Sometimes for such purposes, special brushes with a flexible leg are used, they allow you to clean the pipe and remove not only coffee, but also mineral deposits.

Photo - construction

Cleaning the filter is a little more difficult. With frequent use, various debris accumulates on it: salt plugs, coffee dust, scale. It should be cleaned only according to the instructions, since otherwise, the integrity of the spare part may be damaged. In most cases, it is allowed to wipe it with a swab dipped in alcohol or other degreaser. Rinse the part thoroughly after rinsing.

Photo - filter

Also, problems can be associated with the filter if water leaks from the coffee maker. This is often found in machines manufactured by Moulinex, Krups, Rowenta, Saego. A special valve is installed near the filter, which, after turning off the timer, turns off the water supply. If after a certain time the drink has not stopped flowing, then the cause is a malfunction of this element. The valve may wear out after frequent use, or it may simply not be able to handle the accumulated amount of coffee. To check and fix the breakdown, you need to disassemble the coffee machine, pour the coffee out of it and inspect the valve. Please note that it cannot be repaired, so the part changes immediately.

Photo - disassembly

If the coffee maker Redmond, Spidem, Tefal, Siemens and others does not turn on, then urgent repair is required:

The first step is to check the power wire. It needs to be examined for an open circuit, and also to additionally check the grounding.It connects to the terminal block, so be careful when diagnosing;
Sometimes, household coffee machines made in China simply lose contacts. It also occurs in professional models (zauber, melitta, trevi). In this case, you need to check all the places where the wires are connected to the control circuit;
Many modern cars (Senseo¸Siemens, Ufesa) sin with a low-quality thermostat. To diagnose it, you need to remove one wire from its end and check the contacts with a tester. With a serviceable element, the circuit must be closed;
Also, the coffee maker may not turn on if the heating element needs repair. It is called in the same way as a thermostat. For many models (Jura Impressa, Miele, Gaggia, Butler) it is made in the form of a disk, so it will be rather difficult to change it, it is easier to try to repair a part or buy a new car;
There are also certain secrets to cleaning the engine. In the care products departments, special brushes are sold that will help clean different parts of the motor without damaging the fragile material. It should be noted that in AEG, Solis or Unit coffee makers, the motor has several compartments, each of which is cleaned separately.

Video: Delonghi Coffee Maker Repair

Very interesting to read: We carry out a full-fledged repair of Bork coffee makers. For repairs, we use only original quality parts supplied directly by Bork itself. You can call the master home or office by calling or filling out the form on the website. With minimal workloads of wizards, repairs are possible on the same day.If you have lost some accessory from your coffee maker, then we will disappoint you, it becomes more and more difficult to find the necessary part. Accessories and spare parts for Bork coffee makers are very quickly updated in connection with the release of new models. Therefore, the replacement of necessary parts is carried out only with our work. It is very important to inform us of the correct model of the coffee maker when ordering a repair. For example, the filter (strainer) for the horn in the Bork C800 model differs in size from the Bork C801 model.There are cases quite often when the filter in the horn is clogged and the passage of water is difficult. In this case, the water pump continues to pump water that has nowhere to go. The water begins to look for a path and, as a rule, finds it through the gasket in the thermoblock, which is located directly above the horn. The repair of the thermoblock will cost you 5500 rubles, including spare parts. But the filter will have to be replaced, in particular for double bottom filters. A filter for one measuring spoon costs 1,500 rubles for two 1,800 rubles. For stubborn users who continue to operate the coffee maker with a clogged filter. Repairing a coffee maker can be much more expensive. Because the gasket isn't the only weak point in the coffee maker.Everything is extremely simple here. Very hard water forms calcium (scale) in the heating elements. Untimely descaling has a detrimental effect on the coffee maker as a whole. Scale is a big evil that harms not only the coffee maker, but also our life with you. In almost all cases, a complete stop of water in the system indicates the formation of a plug. And here only the intervention of a specialist can solve the problem. It is necessary to carry out mechanical cleaning without damaging important elements.Humanity invented rubber, and it so happened that rubber does a good job of holding back water. But rubber is not eternal and has the property of rubbing, cracking, cracking and tearing. Especially where there is mechanical interference. We can replace any rubber bands, or you can order and replace yourself. However, in case of self-replacement, you lose any warranty from our company. Improper installation of the rubber seals can instantly nullify performance.These sounds include the incorrect operation of some mechanisms. Such as a water pump (pump) or solenoid valves.The water pump works louder than usual when it has nothing to pump, more precisely, when it is idling. It is necessary to make a diagnosis to identify this cause. The second moment is when the solenoid valves fail. Here, only a complete replacement with service valves is possible.One of the most important things to keep your coffee machine running is water. Clean water is the key to health. Regular water changes and decalcification will prolong the life of you and the coffee maker for a fairly long time. The second most important is the grinding of coffee, too fine grinding complicates the work of several units. Small grains of coffee clog the filter in the horn, and then everything along the knurled, torn gaskets is difficult for water to exit.We repair Bork C700, C800 (CM ENN 9922), C801, C802, C803, C804 coffee machine models. We also repair Jura, Saeco, Delonghi, Bosch, Krups, Siemens, Gaggia, Melitta, Spidem coffee machines, as well as built-in Neff, Kuppersbusch, Smeg, AEG, Miele,Posted by: z88m in Repair, Electrical devices 02/10/2017 0 2,002 ViewsWe once had a chance to repair a Bork C800 coffee machine. As it turned out, the name Bork C800 is a Russian rebranding of the Australian Breville 800ESXL car. If there was no information anywhere on Bork on the Internet, then on Breville, the site helped us a lot, from where we got all the most important information. The following article, for the most part, is a translation of the specified site.More options for solving problems: The pump works when the device is offThe coffee machine is connected to the mains but switched off with the button on the front panel. Suddenly the pump turns on and runs non-stop.We study the electrical circuit (in the picture there is an option for North America with 120VAC power supply):Electrical schematic diagram of the Breville 800ESXL coffee machine

Broken by short circuit Q1

Q1 opens with excessive interference voltage arising on R7

On pin P62 of the microcontroller, an open signal occurs at a time when it should not be (for example, if the power of the microcontroller is out of range)

Troubleshooting is available at siber-sonic.com. Let's go straight to the repair:Replace the thyristor Q1 with a more powerful one (approximately 4A x 600V) - most likely this will be enough. Q1 breaks down due to mains voltage ripple. If you live in an area with poor power quality, then, in order to reduce the voltage peaks that kill Q1, it is worth replacing the varistor V1 with a lower voltage one (within reasonable limits).R7 may get obstructed and open Q1. To prevent accidental opening of the thyristor with high voltage, you can reduce the resistor value from 10 kOhm to 4.7 kOhm and add a capacitance of about 200 pF to it in parallel (25-volt should be enough).Additionally, you can filter out the interference on Q1 with a snubber - an RC circuit added to the thyristor between the anode and cathode. The ratings are approximately as follows: capacitor - 2 nF x 600 V, resistor - 20 kΩ x 0.25 W.American version of the corrected scheme (corrections are indicated in red):And how it looks live (click to enlarge): The pump runs continuously without pulsationYou turn on the car and immediately the pump starts working continuously. Check your circuit, perhaps you have an upgraded board where the power section, including the pump and thyristor, is connected through a relay controlled by the power button. If this is the case, then the malfunction is most likely in the same place as in the case of the disconnected machine. The pump runs continuously with a normal pulsation cycle

The pump only works when the machine is powered on

The pump follows the normal start-up sequence for brewing or steam mode

The pump continues to run as if the control knob remained in the "brew" or "steam" position all the time

The key here is the normal ripple cycle. This tells us that the microcontroller is controlling the pump - the pump does not randomly shut off and does not run continuously. The pump is controlled, although not as expected.We do not know of any cases of failure of the microcontroller, which means that we assume that it is operational and the signals entering the controller are to blame for everything. The most likely source of problems is the two microswitches on the control panel. The handle itself controls the hydraulics - possible water paths:

Through the infuser in the brewing position

Into the overflow tray in standby mode

Through the steam nozzle in the "steam" position

The microswitches are required to transmit information about the selected knob mode to the controller.

In standby mode, power flows through the common line (C) and the normally closed (NC) contacts of S2, transmitting a high signal to the T / F terminal. The pump is off.

In the brewing mode, S2 remains in the same NC position and, in addition, S1 closes, giving the microcircuit a signal to start pumping water.

In steam mode, S2 switches from NC to Normally Open (NO) position. The T / F signal goes down. S1 is open, so P64 is high as in standby. The pump is on in pulsating mode.

If any of these switching signals are incorrect, the microcontroller can activate and control the pump in one of the water delivery cycles at the wrong time. For example, let's say S2 is broken, so it comes with a high resistance or open circuit between C and NC. If this happens, the controller will think it is in steam mode and the pump should continue to pulsate. Second example: if instead there is a short circuit in S1 or C13, then the controller will think that S1 is closed and that it should start the pump in brewing mode, no matter what position the control knob is in.Other combinations of failures are also possible. You need to make sure that the correct high / low signals are sent to the microcontroller for each control knob position. The pump will not turn on and / or the Power LED blinks while the Power button is pressed, then turns offCall the pump with a tester - most likely the point is in it. Please note that the pump has a diode. Does not turn on - no signs of lifeMost likely the problem is in the zener diode ZD6.There have been reports of overheating and failure of the ZD6 zener diode. For reference, here are the specifications for the two main supply voltages, which are labeled V ++ and V +, when everything is working correctly:Immediately after the purchase, the machine did not whip milk well for latte and cappuccino (well, I didn’t know that it was bad - I whipped it somehow), and after a month the steam stopped coming out of the pannarello nozzle altogether. But you could hear steam coming out somewhere inside the car. Assuming, as a former setup engineer, that the problem was insignificant (something jumped off), I decided not to take the coffee machine to the service center through Media-Markt and then wait for the result, either a week or a month, and fix the defect on my own ...

We start disassembling from the base, unscrewing all the screws, except for the legs (they do not interfere with disassembly). At the same time, to unscrew the cover, which includes the power cord, you need a special screwdriver attachment (an asterisk with a hole in the middle. The picture shows the T 10 attachment from the Metabo set):

The plastic base detached from the frame allows you to unscrew and remove the rear plastic cover. Then we unscrew the screws in the wells holding the top cover:

We unscrew the grounding wire of the top cover and while disassembly is enough:

The reason for the release of steam past the Panarello nozzle is already visible:

Apparently, even during assembly, the tube was passed through the inner edge of the fixing nut:

I picked out the remains from the nut, and cut off the jammed end of the tube with a clerical knife. The remaining length of the tube was barely enough to put it on the nipple and press it again with the nut. But if the reason for the squeezing was the twitching of the Panarello nozzle back and forth when whipping milk foam, then this is a constructive miscalculation and you will have to stock up on this rigid PVC tube. But where can you buy this? 🙂

In general, I liked the coffee machine for its solid build quality - all such iron, wires in a fabric sheath, all connectors and connections look reliable and vibration-resistant, like on cars (the red motor is still a vibrator, it's not in vain that it rests on rubber supports):

The bottom line is this: although the key at 11 in an oblique Chinese hand trembled in the morning on Monday after meeting the Chinese New Year, now everything is fine - the foam is not less than 2 cm and thick, even if you put a coin on top ... Image - DIY bork c800 coffee maker repair

Do-it-yourself coffee maker repair - problems, we disassemble it ourselves.

The coffee maker only prepares delicious coffee when it is working properly. Some operational problems may not affect the operation of the appliance itself, but will always affect the taste of the finished drink. There are a number of coffee maker malfunctions that you can fix yourself without contacting a service center.

How to start DIY repair

As with anything else, when repairing a coffee maker, it is important to first identify the problem. With regular use, the most unexpected failures are possible. Therefore, before eliminating the malfunction, the coffee maker must be disconnected from the mains, make sure that there is no hot water in the tank.

Possible manifestations of problems

Hot water, even if it is filtered, still leaves mineral deposits on the parts of the coffee maker. The more there are, the more this affects the taste of the finished drink. To get rid of this malfunction and prevent its occurrence, the device must be cleaned once a month. You can rinse the device with special descaling agents. Of the effective home remedies, experts recommend using acetic acid.

Important! Sometimes the taste of coffee does not change due to malfunctions in the coffee maker, but due to improper storage of the product. Coffee must not be stored open or allowed to come into contact with other products. After all, grains perfectly absorb other tastes and odors.

It happens that very little water flows out of the device, or it does not flow at all. Most often this is due to a blockage in one of the tubes. Aluminum heating tubes are often clogged. To fix the problem, you need to pass vinegar through the coffee maker (do not put filters, coffee). Rinsing is done several times until the water is poured in the right amount. After cleaning, it is necessary to rinse the tubes several times with clean water (do not put filters, coffee in yet).

Too much or little coffee

Many modern appliances have a function to control the amount of brewed coffee. This is a useful feature, thanks to which you can not only brew yourself a cup of drink in the morning, but also take some of it with you in a thermos. Therefore, if the function is available, you need to check its settings. Also check the amount of water in the tank. For correct settings, you can use the instructions for the device, where everything is described in detail.

Not hot enough coffee

The problem in this situation is related to the heating element. It will be necessary to find a spare part to replace the coil. This repair process involves interfering with the internal structure of the coffee maker. Therefore, if there are no skills for such work, it may not be worthwhile to engage in self-replacement.

How to disassemble a coffee maker yourself

When you are confident in your abilities, you can try to disassemble the coffee maker and fix it yourself. It is important to remember that before starting the process, the device must be disconnected from the mains. Do not open the device in case of any breakdown, otherwise, the final repair by a specialist will cost more.

Stages of self-parsing:

1. It is necessary to unscrew the screws on the outer part of the case. As a rule, they are located on the back of the device and can be removed with a screwdriver;

2. There are screws that have no edges and look like bumps. They are unscrewed using pliers (you can turn back the usual screws for a cross-head screwdriver);

3. If there are latches in the case, they must be opened. This is done with a long screwdriver.Typically, these latches are located on the underside of the coffee maker;

4. When the case is open, you can begin to determine the malfunction. It is quite easy to find spare parts for imported devices on free sale. Most likely, you will still need to contact a service center for them;

Sometimes ground coffee gets into the gears of the electric motor and triggers the protection. To clean the coffee maker, turn it over, unscrew the screws and remove the bottom cover. Then clean everything with a vacuum cleaner, grease with grease.

When there are doubts that self-repair will lead to a positive result, it is better not to risk it. Many service centers refuse to repair a device that was previously disassembled at home.

Most of the problems arise due to the fact that a modern coffee brewing machine is an extremely technological device, the operating parameters of which are precisely calculated. Therefore, any violation, whether it is hard water, capsules not recommended by the manufacturer, or other grinding of grains, necessitates repairing the apparatus or understanding how high-pressure systems work. But most of the simple problems can be fixed at home as well. Consider how to repair a coffee maker with your own hands.

If it is decided to independently investigate the coffee maker and carry out repairs, then it is worth taking basic safety measures:

The device must be disconnected from the network.
You need to work with a tool with insulated handles.
Water and wet hands are potential hazards.

Disassembling the body of most coffee makers is not difficult. Often it is enough to unscrew a few screws on the back cover. This makes it possible to gradually disassemble the device into units or large parts. At the same time, there are subtleties: in Delongy's cars, the bolts located on the lower part are closed with plugs or are under the rubber feet, and many Saeko models additionally require the removal of fasteners to remove individual blocks that open access to the areas needed for repair.

In order not to be mistaken, refer to the help information. If the coffee maker does not lend itself to logic and does not understand, it is better to look for data on the model on the Internet.Many devices, in addition to the self-tapping screws on the back of the case, also have latches that hold the top cover or bottom.To find such a fastener, you will need a thin screwdriver or knife, which passes the line of joint of the parts until the localization of the zone where you can press the latch.Models with VT1513 and VT1511 are leaders in the problem of violation of the fluid supply regime. These are extremely convenient coffee makers operating under a pressure of 16 atmospheres and allowing you to prepare delicious espresso. However, even the slightest mismatch in the grind, as well as the use of hard water, can cause problems with the fluid supply.If the grinding is too fine, the screens and filters are clogged on the Vitek VT1511 and VT1513 models. If you use too large, the drink will not brew. Hard water will clog the high pressure pipes. And all this leads to serious breakdowns - failure of the injection pump or cracking of the plastic switch block. Image - DIY bork c800 coffee maker repair

Vitek VT1513 Coffee Maker Pump

To carry out maintenance or repairs, you must first disassemble the device:

The top aluminum lid is removed where the cups are located.
The fastening screws hidden under the rubber pads are found.
Self-tapping screws are removed, the back cover is removed, giving access to all nodes.

Potential breakage areas can be seen immediately. High pressure tubing - hard, thin. The feed selector is a small plastic block that the distributors fit into. The blower is a round metal pump. To repair the Vitek coffee maker you will need:

Assess the condition of the high-pressure pipes, check the places of their fixation - there should be no looseness, cracks.
Check the condition of the blower housing. Splits or traces of overheating indicate a possible pump malfunction.
Inspect the condition of the feed switch.

If, after assessing the reliability of contacts, the problem is still not clear, carry out the following operations:

Clean the high pressure pipes. For this, you can use thin rubber tubes or a single-core wire with soft insulation. There is also a special tool - a flexible brush.

Check fasteners and contacts, remove all dirt.

Clean the filters.

After that, the coffee maker starts up and is re-checked for the operability of the nodes. By the way, the most common accident is crack in switch, it is determined by the presence of water on the surface of the part. The damage cannot be sealed (pressure will squeeze out any sealant). Therefore, it is worth replacing the block or simply melting the crack, heating a knife or screwdriver on the gas burner. Image - DIY bork c800 coffee maker repair

Breakage of the Vitek VT1513 mode switch

If disassembly, cleaning, visual inspection of the coffee maker did not allow to localize the problem, most likely, the matter is in the blower, and it is necessary to call a specialist.

There are many common breakdowns. It is not difficult to repair them with your own hands. For instance:

clogged filter

Oxidation of contacts became more and more common, as manufacturers began to save every penny in production. Obligatory cleaning and regular checking of contacts is the key to the successful operation of the coffee maker.

Failure of the heating element... Repairs in this case must be carried out by a specialist. Since there are models of coffee makers, the heating element of which cannot be dismantled without damaging other parts. The cost of work and the purchase of a new spare part will cost more than a new device.

The main part of the repair is a thorough cleaning of all nodes and contact groups. Without carrying out this operation, there can be no question of any thorough testing of the electrical parameters of motors, temperature sensors, electronic units. These actions will be ineffective to say the least.

Each coffee maker comes with an instruction manual. It describes the typical problems of a particular model and provides ready-made recipes for solving them. Often these are instructions like "the coffee maker won't turn on - check the wire." Yes, the integrity of the power cable, the absence of scuffs, fractures, mechanical damage - this must be checked without fail.

However, the general principle of repair is reduced to moving from simple to complex. Something does not turn on - the functionality of the button is checked, the cleanliness and reliability of the contact. The operating parameters do not correspond to the expected - the regulators and sensors are closely examined, cleaned, lubricated, if necessary, replaced. To eliminate common malfunctions of coffee makers, you need to act on the principle of a thorough examination of parts for damage, full service of all filters, pipes, contact groups and sensors.

Video (click to play).

A coffee maker is an indispensable device in modern life, but the complexity of its device implies strict adherence to the manufacturer's recommendations. In order to constantly enjoy a fragrant drink, use coffee of the correct grinding, a certain type of capsule, and also periodically service the machine.