DIY jura coffee maker repair

In detail: do-it-yourself jura coffee maker repair from a real master for the site my.housecope.com.

Most of the problems arise due to the fact that a modern coffee brewing machine is an extremely technological device, the operating parameters of which are precisely calculated. Therefore, any violation, whether it be hard water, capsules not recommended by the manufacturer, or other grinding of grains, make it necessary to repair the apparatus or understand how high-pressure systems work. But most of the simple problems can be fixed at home as well. Consider how to repair a coffee maker with your own hands.

If it is decided to independently investigate the coffee maker and carry out repairs, then it is worth taking basic safety measures:

The device must be disconnected from the network.
You need to work with a tool with insulated handles.
Water and wet hands are potential hazards.

Disassembling the body of most coffee makers is not difficult. Often it is enough to unscrew a few screws on the back cover. This makes it possible to gradually disassemble the device into units or large parts. At the same time, there are subtleties: in Delongy's cars, the bolts located on the lower part are closed with plugs or are under the rubber feet, and many Saeko models additionally require the removal of fasteners to remove individual blocks that open access to the areas needed for repair.

In order not to be mistaken, refer to the help information. If the coffee maker does not lend itself to logic and does not understand, it is better to look for data on the model on the Internet.

Many devices, in addition to the self-tapping screws on the back of the case, also have latches that hold the top cover or bottom.

Video (click to play).

To find such a fastener, you will need a thin screwdriver or knife, which passes the line of the joint of the parts until the localization of the zone where you can press the latch.

Models with VT1513 and VT1511 are leaders in the problem of violation of the fluid supply regime. These are extremely convenient coffee makers operating under a pressure of 16 atmospheres and allowing you to prepare delicious espresso. However, even the slightest mismatch in the grind, as well as the use of hard water, can cause problems with the fluid supply.

If the grinding is too fine, the screens and filters are clogged on the Vitek VT1511 and VT1513 models. If you use too large, the drink will not brew. Hard water will clog the high pressure pipes. And all this leads to serious breakdowns - failure of the injection pump or cracking of the plastic switch block.

Vitek VT1513 Coffee Maker Pump

To carry out maintenance or repairs, you must first disassemble the device:

The top aluminum lid is removed where the cups are located.
The fastening screws hidden under the rubber pads are found.
Self-tapping screws are removed, the back cover is removed, giving access to all nodes.

Potential breakage areas can be seen immediately. High pressure tubes are hard, thin. The feed selector is a small plastic block that the distributors fit into. The blower is a round metal pump. To repair the Vitek coffee maker you will need:

Assess the condition of the high-pressure pipes, check the places of their fixation - there should be no looseness, cracks.
Check the condition of the blower housing. Splits or traces of overheating indicate a possible pump malfunction.
Inspect the condition of the feed switch.

If, after assessing the reliability of contacts, the problem is still not clear, carry out the following operations:

Clean the high pressure pipes. For this, you can use thin rubber tubes or a single-core wire with soft insulation. There is also a special tool - a flexible brush.

Check fasteners and contacts, remove all dirt.

Clean the filters.

After that, the coffee maker starts up and is re-checked for the operability of the nodes. By the way, the most common accident is crack in switch, it is determined by the presence of water on the surface of the part. The damage cannot be sealed (pressure will squeeze out any sealant). Therefore, it is worth replacing the block or simply melting the crack, heating a knife or screwdriver on the gas burner. Image - DIY jura coffee maker repair

Breakage of the Vitek VT1513 mode switch

If disassembly, cleaning, visual inspection of the coffee maker did not allow to localize the problem, most likely, the matter is in the blower, and it is necessary to call a specialist.

There are many common breakdowns. It is not difficult to repair them with your own hands. For instance:

clogged filter

Oxidation of contacts became more and more common, as manufacturers began to save every penny in production. Obligatory cleaning and regular checking of contacts is the key to the successful operation of the coffee maker.

Failure of the heating element... Repairs in this case must be carried out by a specialist. Since there are models of coffee makers, the heating element of which cannot be dismantled without damaging other parts. The cost of work and the purchase of a new spare part will cost more than a new device.

The main part of the repair is a thorough cleaning of all nodes and contact groups. Without carrying out this operation, there can be no question of any thorough testing of the electrical parameters of motors, temperature sensors, electronic units. These actions will be ineffective to say the least.

Each coffee maker comes with an instruction manual. It describes the typical problems of a particular model and provides ready-made recipes for solving them. Often these are instructions like "the coffee maker won't turn on - check the wire." Yes, the integrity of the power cable, the absence of scuffs, fractures, mechanical damage - this must be checked without fail.

However, the general principle of repair is reduced to moving from simple to complex. Something does not turn on - the functionality of the button is checked, the cleanliness and reliability of the contact. The operating parameters do not correspond to the expected - the regulators and sensors are closely examined, cleaned, lubricated, if necessary, replaced. To eliminate common malfunctions of coffee makers, you need to act on the principle of a thorough inspection of parts for damage, full service of all filters, pipes, contact groups and sensors.A coffee maker is an indispensable device in modern life, but the complexity of its device implies strict adherence to the manufacturer's recommendations. In order to constantly enjoy a fragrant drink, use coffee of the correct grinding, a certain type of capsule, and also periodically service the machine.If the Jura coffee machine stops working, you should not immediately call the technician and pay money for the repair. You can visually inspect, find the problem and fix the malfunction yourself. Some malfunctions do not require special knowledge. If outwardly the models differ from each other, then the internal structure and principle of operation are the same for them.But nevertheless, it will not be superfluous to familiarize yourself with the instruction manual. Repairing your Jura coffee machine will be easy if you understand the internal structure, in which there is nothing complicated. However, the Jura Impressa coffee machine is quite expensive, and without the skill in disassembling household appliances, you should not risk it.Proper care and use will greatly reduce the risk of malfunctions. Therefore, it is imperative to take preventive measures and carry out timely cleaning of internal parts and filters.All recommendations are regulated by the manufacturer in the instructions for use. Image - DIY jura coffee maker repair

Poor quality water. For coffee machines, use only high-quality water, preferably filtered, with the lowest content of impurities.
Voltage surges in the electrical network.
Improper use of the device.
Wear of spare parts.

At the same time, not all malfunctions can be corrected on their own. If the cause is, for example, the engine, then it is best to have your Jura repaired by a specialist.

What problems of the Jura coffee machine can be eliminated with your own hands:

Leakage of water. To do this, inspect the O-ring - it may be clogged or damaged. To remove it, you do not need to make a lot of effort, just poke it out with a screwdriver. If after that it does not come out, then it is possible that it is damaged and should be replaced. If there is no damage, then it is enough to simply clean it.
The machine does not respond to button presses. To fix the problem, you can wipe them with alcohol to remove dirt and dust. If this measure does not work, it is possible that the problem is related to the electrician, and it is worth calling the technician.

More details about the structure and malfunctions of the Jura Impressa coffee machine are described in the video.

The following measures will help to avoid many problems:

Filtration and use of cold water only.
Using only high quality dry coffee beans.
Make sure that no foreign objects fall into the device.
Regular flushing of the system using specialized cleaning agents under the Jura brand.

You cannot start the Jura coffee machine without making sure that the water has been poured.
The filters should be cleaned regularly, preferably after 25 uses, even if the system does not require cleaning.

If you are unable to repair the damage yourself, contact a Jura service center.Hello everyone, we continue the opuses about playful hands.Three weeks ago, the following device randomly appeared on the farm:
Image - DIY jura coffee maker repair

Three weeks ago, the following device randomly appeared on the farm:

Lying under the balcony these three weeks, the machine was waiting in the wings.
And the free hour has come.
I had nothing to do with coffee machines at all, which really fueled my interest.

Laundered it, turned it on.
A cursory troubleshooting revealed:
1. The coffee machine switches on.
2. The coffee machine is heating the water.
3. The coffee machine DOES NOT grind coffee.
4. The coffee machine does not want to take back the brewing unit.
Along the way, it turned out that this coffee machine is a complete analogue of the Saeco Vienna.
After a cursory ringing of services, it was found out that everything is bad: repair like, it costs half of the device.

Having rummaged through the repair forums, I managed to find drawings and a video of the disassembly of the coffee machine:

After some more digging, I managed to find drawings for disassembly.

Well, it started:
We disassemble the case, disassemble the coffee grinder:

I note right away: on Italian machines, there are usually 2 types of coffee grinders:
horizontal and vertical.
And it is these 2 types that are in 90% of the cases of modern coffee machines.
When disassembling the coffee grinder, we understand that ground coffee has been poured into the grinder, which is absolutely impossible to do,
then they tried to rinse it, which is also not allowed - the coffee coked the grinding gears (millstones) and put everything around it.
This coke had to be beaten off from the millstones with a screwdriver!
We clean everything, vacuum if necessary.
Pay attention to the drawing - without it, assembling the coffee grinder unit correctly is problematic.

Next, we deal with the brewing unit.
We find out the following: the brewing unit was pulled out of the coffee machine
without turning it off, and this should never be done.
The coffee machine has not put the gear that turns the brewing unit mechanism to its original position.
And then they tried to push the brewing unit into the coffee machine,
and the main gear of the brewing unit mechanism spun slightly.

After disassembling the gear block, we admire the Italians once again:
the gear spun 90 degrees relative to the base position!
but all the teeth are intact both on it and on the transmission gear.
But even if the teeth were cut, it doesn't matter - the set of gears is worth
from private traders 390 rubles.

At the same time, I met a private trader for the repair of coffee machines (useful acquaintance!)
and bought lids for a container with water and coffee - the car was without them.

We return the main gear to its original position,
my brewing unit and diligently putting the coffee machine back.
Along the way, we set the toothed adjusters for grinding coffee, the adjuster for the amount of coffee in its original positions,
after all, we went through the coffee grinder.
Without this operation, the coffee grinder will grind the coffee either coarsely or finely, adjustment
will be archaic.

Next, we clean the heating part of the coffee machine with a decalciner:

Well, go ahead, cappuccino !:

I would like to advise all co-candidates:
don't forget to clean your coffee machines!
Take out the brewing unit every couple of weeks and wash it with lukewarm water.
Don't be lazy to vacuum the grinder funnel every couple of three months!
Well, once every half a year (especially for summer residents) flush the system from lime.
And your coffee machine will work for you for sooooo long.
Well, one more conclusion: it is quite possible to do the maintenance of the coffee machine yourself.
This is the hour.
And it is quite possible to fix the car - all spare parts are either on Ebey or in Moscow.

]

Self-repair of coffee machines and maintenance in some cases will save not only money, but also time. At least what you will spend on a trip to the workshop or waiting for the master. Therefore, do not rush to call the master and rush to the service, read the advice of specialists SC REMO. PLUS , perhaps you can solve the problem of repairing, setting up or cleaning the coffee machine - with your own hands.

So. We are ready to share tips and help you to repair the coffee machine yourself, carry out those. Maintenance or cleaning. Tips from easiest to hardest. Before proceeding with the repair, assemble the necessary tool, do not start disassembling the coffee machine with one screwdriver and duct tape. The minimum required for repairs is a set of different screwdrivers, maybe wrenches, pliers, nippers and a tester, but what exactly depends on the model of the coffee machine and the breakdown. The outcome of the repair depends very much on the tool. Spare parts for the repair of a coffee machine can be bought in our company, you can find out about the availability by phone.

If you have any questions about the maintenance, configuration and operation of the coffee machine - call We will try to help you figure it out. But we do not conduct telephone courses on the repair of coffee machines.

How can I clean coffee grease, decalcify the hydraulic system and rinse the milk system on my own?

The processes of cleaning and decalcifying a coffee machine cannot be described in a nutshell, on this topic we have a page with expanded, detailed explanations - follow the link.

Milk should be pasteurized, 2.5-3.5% fat. Sterilized milk that can be stored for half a year and that - which is made from powder - will not be whipped. The milk may not come out because the cappuccinatore is clogged. If after the last use it was not washed immediately, but after a while, the hardened milk could clog the air channel, which is often in the form of a hole or groove inside the cappuccinator body. Thinner than a sewing needle. Therefore, inspect the cappuccinator, try to find it and rinse it. But it is unacceptable to enlarge this hole or channel - spoil the cappuccinator.Can be cleaned with a toothpick and water. It is quite difficult to find an air channel in an automatic cappuccinator if you do not know where it is and how it should look. Therefore, just disassemble the auto cappuccinator into components that can be removed, disassembled without screwdrivers, rinse everything thoroughly, assemble as it was. This manipulation should solve the problem. Taking into account the fact that the steam goes in a dense stream and does not require cleaning the hydraulic system, the cappuccinator is included and nothing is lost, and, accordingly, there are no mechanical damages or cracks on it.

On a coffee machine Delonghi the infuser moves very tightly.

Because of this, the coffee spills and periodically the coffee machine signals a malfunction of the brewing device. Remove the infuser, sort it out, but take your time - take pictures and remember where what was and in what position. Having disassembled the block, you will see two seals on the piston. Replace them with new ones, wash and remove any dirt that is there. Lubricate the unit's brewing chamber with a thin layer of gasket with food grade grease. Collect everything? as it was. Place the Infuser on the workstation. Prepare and drain 3-5 standard cups of coffee. If everything works smoothly and without interruptions, you can use and drink coffee.

Automatic coffee machines. The coffee is probably ground too fine. You can define it by type. Look at ground coffee, it should be similar in size to semolina, if it is closer to clay in consistency, adjust the grinder to a larger side. Note, however, that when adjusting the grinder, the result of the change in grind will be visible after the fourth cup. This is due to the fact that there was already ground coffee in the coffee grinder and in the coffee maker before the change, and until it is completely renewed for a new grind, the result will not be visible. Do not rush to rotate the grind after each coffee brewing.

For carob coffee makers - if you use a coffee grinder, everything is the same. If you buy ground, change the manufacturer. And it doesn't matter that you always bought this particular coffee and everything was fine. When grinding at the plant, this time the grinding could be made finer, and now the coffee maker cannot cope with such grinding. Perhaps for your favorite type of coffee this will be a temporary phenomenon and the next batch will be the same grind as before. Another way for a carob coffee maker, if the water does not pass through the coffee well, do not temper too much and make the bookmark less. Make sure that without coffee, water passes through the holder (horn) normally.

The water filter that is installed in the water tank or inside the body of the coffee maker or coffee machine may be clogged. The filter in the tank is just enough to remove and try how the water supply works without it. It is possible that it is necessary to carry out decalcification or cleaning with disassembly of the coffee machine and this will solve the problem. In order to clean the internal filters, you need to disassemble the coffee machine. If it is not about the filters, perhaps the pump is worn out, it does not create the required pressure - it needs to be replaced.

In automatic coffee machines the reason may be the filter on the brewing unit - this is the metal mesh on the piston. This can be eliminated by replacing it. Everything under the net also needs to be cleaned.

In carob coffee makers it often happens that the holder filter is clogged - this applies especially to coffee makers KRUPS and BORK... If the filter is in two parts, coffee deposits accumulate between them, which makes it difficult for the coffee to pass. Clean the filter with any available coffee grease cleaner.No matter how the metal filter of the holder or the infuser is clogged, do not pick out the holes with needles, do not increase their size. This will only spoil the filter. You can try to do this if you definitely decided to replace it, but first make sure that you can buy one.

Water / wet or greasy coffee has entered the grinder.

The water container in the coffee machine is rusty from the tap water - how and how to clean it?

If you see rust on the walls of the container, then it is the same, and most likely it looks several times worse inside the coffee machine. The pipes usually have an impressive coating, which gives the water a stale, unpleasant aftertaste. It can only be cleaned by completely disassembling the coffee machine and removing plaque by hand, mechanically. There are no tools that would completely remove traces of rust without leaving any residue. And aggressive chemicals after use themselves need to be removed, so you still have to disassemble the coffee machine. The water container can be washed with any brush with dish detergent, and the hydraulic system cannot be washed like that. In the future, do not use tap water, only through a filter , preferably stationary, or bottled clean water.

If this happens even when the coffee machine is not working, then it's okay. The seal on the coffee machine in the water inlet will most likely need to be replaced. The seal loses its elasticity from time to time and begins to pass water.

But this is provided that the water began to leak not after the coffee machine was in the cold. If the coffee machine is frozen, it can leak anywhere. Disassemble the coffee machine - look for a leak.

If you need to turn the tap to supply water to the coffee machine, then to eliminate the leak it is necessary to replace the rubber seals on the valve of the water and steam supply tap. If the seals are elastic in normal condition, then carefully wipe the inside of the steam tap and the seals from dirt and old grease with a cotton swab. Lubricate the seal with food grade grease and collect.

If the replacement of the seals, cleaning and lubrication did not help, the valve body itself is probably damaged - a crack, depletion. Replace the valve assembly.

If you need to press a button on the control panel of the coffee machine to supply water and steam, then this function is electronically controlled. Most likely - the mechanism of the electromagnetic valve responsible for the water supply is damaged or clogged with scale. Try decalcifying and if this does not solve the problem, replace the solenoid valve.

Of course - new is always better. But it is more advisable to replace worn or broken parts and operate further. If the Brewing Device was not dropped, cleaned in a timely manner and did not break on purpose, then the main parts are probably intact and not worn out, so you do not need to change everything. To repair and bring to perfect condition any Brewing device will cost 2-3 times cheaper than buying a new one. And why change the work items for new ones - replace only what is really needed.

Look at the condition of the seal, if there are any coffee deposits, if there is, clean it carefully.

The second thing that can be is damage to the seal, or it simply dried out from the temperature and lost its elasticity. In order to replace the old damaged seal, unscrew the group filter (sometimes there are difficulties with this). Remove the filter - this will usually fix the seal. And then take out the seal, clean everything of coffee deposits, install a new seal, collect everything as it was and use it.

When using household and professional espresso machines - do not allow ground coffee to come into contact with the seal of the group. This is how the seal grinds off with sand and it will deteriorate very quickly. It is better to regularly monitor the condition of the group and clean it from any contamination.

What to do if the coffee machine is leaking while making coffee, but it is still making coffee? Can the coffee machine be operated if it is leaking?

If you are very lucky and rich, you probably can. But operating faulty equipment is always dangerous! You don't know what is flowing from where, whether water gets on the electrical contacts, what all this will lead to. And the leaking water can spoil the surface on which the coffee machine stands. If the coffee machine leaks, then it will not stop leaking until the cause is eliminated, do not hope that everything will go away by itself.Disassemble the coffee machine - look for a leak! Most often, it is enough to replace all the seals in the hydraulic system (it sounds simple, but you need to disassemble all the connections, fittings and valves that are in the coffee machine, look at them and assess their condition). If you change the old seals only those that are leaking, and leave the rest, it is possible that you will be engaged in eliminating leaks every month. Therefore, the seal started to flow in one place, we change - that's it! The boiler can also leak - if it is made of two halves. Most often, the seal is also to blame, although it is not always possible to disassemble the boiler and the condition of the boiler is not always better than a failed seal. Here you will have to assess the condition of the boiler yourself, repair it, or replace it entirely.

If the leak is not eliminated immediately, then, most likely, some other blocks, mechanisms, electronics, metal will begin to rust and rot along the way from steam and hot water. Then the cost of repairing a coffee machine, even with your own hands, can become impractical and very expensive. An example of long-term operation with a leaking boiler is in the photo.

In the JURA coffee machine, the brewing mechanism runs slowly, after switching on and testing the display shows the error F8.

In this case, in Jura coffee machines, in 80% of cases, the cause is in the brewing mechanism. It needs to be disassembled, cleaned, old seals replaced, reassembled and everything will work as before. But if any of the plastic elements of the brewing device are damaged, then it will be difficult to replace them. It is practically impossible to find individual spare parts for the JURA charger, the brewing device is usually sold assembled, but it is possible that you will be lucky. Only a drain valve is available separately. But it has nothing to do with error F8. Disassembly of the JURA charger in the photo below.

That's not all, other tips will be added and laid out as the work on the text is completed.

Before disassembling the coffee machine, adequately assess your capabilities. Often the beginning of a self-repair does not guarantee its successful completion, but rather only exacerbates the condition of the coffee machine. Consider the time that you spend on mastering repairs and buying a tool. At your work, during the same time, you may earn more than you pay for repairs, and besides, an expensive coffee machine is at stake - it may be better to entrust repairs to REMO specialists. PLUS receive a fully working and tuned device with a guarantee for the performed repairs. Not? Then get started!

Jura coffee machines Is the most famous brand that embodies the recognized Swiss quality. Do high-quality devices break down? It is a myth. Despite the fact that coffee makers and coffee machines of the latest generation have excellent reliability and durability, any device can break down over time under the influence of external factors, careless handling, or simply due to the fact that the equipment is outdated.

What is the job of Jura coffee machine service and repair professionals? Repair of expensive equipment should be trusted only by professionals who have experience and qualifications in this area. Our masters will be able to professionally diagnose the coffee machine and identify a malfunction, as well as carry out high-quality repairs. Our service center carries out high-level repair of coffee machines of various brands, including Jura.

Our qualification for the repair of Jura coffee machines is confirmed by the corresponding certificate from the Swiss company Jura.

Why do coffee machines break down? Jura?

How is the diagnosis and repair of a coffee machine carried out? Jura?

In the course of diagnostics, in addition to identifying a malfunction, the parts are checked for the percentage of wear and the identification of possible problems in the future.

Repairs of Jura coffee makers can be carried out directly on site (service of a visit of a service engineer) or on the territory of the service center of our company. After a while, you will be able to return to the usual rhythm of your day, which will certainly begin with a cup of your favorite aromatic espresso.

Upon your call, a coffee machine master from our company will come to you, who will perform the initial diagnostics and draw up a defective statement with a calculation of the cost of repair work and spare parts necessary for resuscitation. The Jura coffee machine can be repaired at the client's site without transporting the coffee equipment to the service center, unless the coffee machine specialist decides that it is necessary.

If necessary, your coffee machine will be immediately delivered to our service center at shipping rates and all diagnostics and repairs will be performed with us. The service center has all the necessary diagnostic equipment and spare parts, which will allow you to quickly repair your Jura coffee machine. After the diagnostics, the foremen of our company will be able to name the exact cost of the repair. The client will be able to make an important choice only on the basis of qualified diagnostics, whether it is worth making a repair or it is better to abandon it and purchase a new coffee machine.

Attention! If in a competitive environment there is a proposal for free shipping - be prepared for the cost of delivery to be included in the repair!

You can also independently bring a coffee machine to us for repair at the address of our service center during business hours.

Service of coffee machines Jura... Cleaning from coffee oils and limescale.

As you know, it is easier to prevent a disease than to cure it later. Caring for your coffee machine involves regularly cleaning your Jura to remove coffee oils and limescale deposits.

The user of the coffee machine can independently carry out periodic care of his coffee equipment, using cleaning agents for caring for the device - filters, tablets from limescale and coffee oils, liquid for cleaning the cappuccinatore. As a result of preventive measures, the cappuccinatore, the coffee supply path and the entire hydraulic system as a whole are cleaned.

Routine maintenance is best trusted by professionals who can identify faults in a timely manner and provide professional advice. Prevention will help to avoid repair work and unnecessary costs.

Our qualification for the repair of Jura coffee machines is confirmed by the corresponding certificate from the Swiss company Jura.

Why do coffee machines break down? Jura?

How is the diagnosis and repair of a coffee machine carried out? Jura?

In the course of diagnostics, in addition to identifying a malfunction, the parts are checked for the percentage of wear and the identification of possible problems in the future.

Upon your call, a coffee machine master from our company will come to you, who will perform the initial diagnostics and draw up a defective statement with a calculation of the cost of repair work and spare parts necessary for resuscitation.The Jura coffee machine can be repaired at the client's site without transporting the coffee equipment to the service center, unless the coffee machine specialist decides that it is necessary.

Attention! If in a competitive environment there is a proposal for free shipping - be prepared for the cost of delivery to be included in the repair!

You can also independently bring a coffee machine to us for repair at the address of our service center during business hours.

Service of coffee machines Jura... Cleaning from coffee oils and limescale.

As you know, it is easier to prevent a disease than to cure it later. Caring for your coffee machine involves regularly cleaning your Jura to remove coffee oils and limescale deposits.

Video (click to play).

Routine maintenance is best trusted by professionals who can identify faults in a timely manner and provide professional advice. Prevention will help to avoid repair work and unnecessary costs.

Rate the article:

Grade 3.2 who voted: 85

DIY jura coffee maker repair

How can I clean coffee grease, decalcify the hydraulic system and rinse the milk system on my own?

On a coffee machine Delonghi the infuser moves very tightly.

Water / wet or greasy coffee has entered the grinder.

The water container in the coffee machine is rusty from the tap water - how and how to clean it?

What to do if the coffee machine is leaking while making coffee, but it is still making coffee? Can the coffee machine be operated if it is leaking?

In the JURA coffee machine, the brewing mechanism runs slowly, after switching on and testing the display shows the error F8.

Popular

Do-it-yourself gas 3110 front suspension repair

Do-it-yourself uaz onboard repair

DIY LED driver repair

Do-it-yourself repair of a vaz 2110 stove replacement

New items

Do-it-yourself fluorescent lamp repair

Do-it-yourself whirlwind 20 boat motor repair

DIY screwdriver drill repair

DIY priors repair priors

How can I clean coffee grease, decalcify the hydraulic system and rinse the milk system on my own?

On a coffee machine Delonghi the infuser moves very tightly.

Water / wet or greasy coffee has entered the grinder.<img title="" alt="Image - DIY jura coffee maker repair" src="#" class="">

The water container in the coffee machine is rusty from the tap water - how and how to clean it?

What to do if the coffee machine is leaking while making coffee, but it is still making coffee? Can the coffee machine be operated if it is leaking?

In the JURA coffee machine, the brewing mechanism runs slowly, after switching on and testing the display shows the error F8.

Popular

New items

Water / wet or greasy coffee has entered the grinder.