It is better to stretch the spring plate with a partner so that the end of the cord does not reel into the starter mechanism.
Assembling the starter on the trimmer and winding the spring is not difficult, you just need to do it carefully and with care. For different models of petrol cutters, the breakdowns of the triggering mechanisms are the same, so they are repaired in the same way. At the same time, there are some nuances associated with their design features.
VIDEO
An indispensable tool for a modern summer resident or owner of a private house is a petrol cutter, which allows you to effectively and efficiently put the adjacent territory in order. The period of active use of brushcutters is in late spring until October. Modern units are equipped with powerful and durable internal combustion engines, reinforced transmission and main components.Despite this, physical wear, manufacturing defects or improper operation lead to failure of the trimmer. In order to repair the trimmer with your own hands, you must have at least basic knowledge in the field of technology and little experience in repairing it.
The main unit of any gasoline tool is the internal combustion engine (ICE), which, through various methods, transmits the torque to the actuator. In a modern petrol cutter, a duralumin rod (pipe) is used as a transmission element between the engine and the trimmer head, inside which the drive shaft is located.
Thanks to the high-revving engine, the line speed can reach 13 thousand revolutions per minute, depending on the manufacturer of the scythe. In order to exclude mechanical and thermal damage to the gearbox, a special hole is provided in its housing for the introduction of grease in the form of ointments. To make the headset easier for the owner during long-term work, all brushcutter models are equipped with a durable shoulder strap.
Regardless of the manufacturer, almost every model comes with a line and steel knives.
The cross-section of PVC trimmer line can vary from 1.5mm to 3.0mm.
Made of durable polymer, it is subject to intense wear and tear during mowing and, as a result, breakage. Therefore, from time to time it is necessary to check the presence of a fishing line in the head and, if necessary, replace it. It is recommended that you purchase an extra bobbin to quickly replace it with an out of line spool.
ICE trimmers on the market today are equipped with a D-shaped, U-shaped or T-shaped handle, where the main controls of the unit are located. For example, in a braid with a U-shaped grip, the throttle key and stop / start toggle switch are located on the right grip. In the D-shaped version of the handle, the throttle control button is located directly on the rod.
Due to the presence of many components and parts, repairing a trimmer with your own hands means eliminating breakdowns that prevent its normal operation. It should be noted the most basic malfunctions of gasoline streamers:
The trimmer motor is not picking up speed;
Breakdown of the cylinder-piston group (CPG);
Ignition malfunctions;
There is no connection between the internal combustion engine and the trimmer head;
Mechanical knocking during unit operation.
Repair of the central piston group petrol cutters
The main unit of any internal combustion engine is a cylinder-piston group (CPG), which can fail due to wear of parts of parts or poor quality of the fuel mixture.
Lubrication of rubbing units in a petrol brush is carried out by adding a certain proportion of oil to gasoline. This process can be disrupted due to old oil precipitating out. In this situation, when starting the trimmer, the motor overheats and in a matter of minutes the most expensive breakdown occurs. To eliminate the malfunction that has arisen, a complete replacement of the CPG will be required, namely: the piston, oil seals, cylinder and piston rings. If you are not an ICE repair technician and do not have experience working with technicians, then you will hardly be able to fix the engine without the help of a specialist. Details on the stages of piston trimmer repair can be found here.
If the ignition of the petrol mowers fails, the spark on the candle disappears and, as a result, the fuel mixture does not ignite.
Spit spark plug design
In this situation, it is quite important not to rush to replace the coil, since the cause of the breakdown may be the lack of contact in the switch on the control handle.
An important point when troubleshooting the trimmer ignition will be the section diagnostics, where the distance between the side and center electrodes should be 0.5-0.7 mm.In addition, it is necessary to pay attention to the steel O-ring on the spark plug, the loss of integrity or deformation of which can lead to etching of air from the combustion chamber and, as a result, reduce the power of the streamer.
Ignition flywheel with coil
If the replacement of the check of the electrical circuit, the spark plug and its contacts did not give positive results, then you should pay attention to the trimmer ignition module, namely the clearance with the flywheel. Regardless of the design features and the manufacturer of the brushcutter, the distance between the ignition coil and the flywheel should be no more and no less than 0.2 mm. To restore the optimal value of the gap, you will need to loosen the coil mounting bolts and set the trimmer ignition with a special measuring probe.
A clear sign of a malfunction of the engine power system is the absence of traces of the fuel mixture on the spark plug electrodes, which may be associated with the following defects:
Trimmer Fuel System Components
due to a clogged hole in the gas tank, a vacuum is created, which prevents the normal flow of gasoline into the carburetor;
due to the poor quality of the fuel and the ingress of foreign particles, the fuel filter installed in the tank is clogged;
non-flow of the mixture into the combustion chamber as a result of a clogged carburetor.
You can quickly determine the cause of the malfunction by dismantling the fuel hose leading to the carburetor. If the fuel mixture flows out in a thin stream, then you should pay attention to the carburetor. If there is no jet, it is necessary to clean the breather with a thin needle (a small hole in the gas tank cap) or replace the fuel filter.
If fuel enters the carburetor, it must be cleaned or adjusted. Adjusting the carburetor trimmer means restoring optimal fuel mix.
Trimmer carburetor with adjustment screws
To do this, pay attention to three adjusting screws: maximum speed (H), minimum (L) and idle speed (LA). To start the adjustment, you need to fully tighten the screws H and L and loosen one turn each. Then we start the braid and let it warm up for 10 minutes to adjust the power system in operating mode. After warming up the internal combustion engine, press the gas supply button until it stops (12,000 rpm). We restore the idling mode by unscrewing the screw LA. As soon as the trimmer head starts rotating, tighten the screw until it stops.
One of the frequent faults of the petrol mowers is the incorrect operation of the internal combustion engine, namely the drop in power when the speed increases (the scythe stalls).
The reason for this is that the exhaust system is clogged with burnt oil particles. Often manufacturers make mufflers prefabricated and cleaning is quite simple. If the design of the spark arrester is non-separable, then it must be placed in water with detergents, and then dried with an ordinary or industrial hair dryer. Frequent clogging of the exhaust system indicates non-observance of the proportions of oil and gasoline.
Very often, complaints from owners of gasoline trimmers are associated with various kinds of carburetor malfunctions. Of course, in this case, it is best to seek help from specialists in this field, for whom the repair of carburetors of gasoline trimmers is an integral part of the profession. However, if you are still familiar with the basic principles of the trimmer carburetor, you can try to figure out the problem yourself, so as not to overpay money in the service, since sometimes the breakdown can be really frivolous.
This article is just intended to help you deal with the problem.
Next, we will analyze the most common breakdowns and the reasons for their occurrence.
The first step is to generally inspect the carburetor and find out if there is any fuel leakage.
If it turns out that there are no problems with fuel, it is necessary to remove the carburetor from the engine and check the condition of the gasket located next to the carburetor.
If no malfunctions are observed here, you can try to check the carburetor for tightness.
To do this, you can purchase a special device, which is part of the tool kits for repairing the carburetor repair of mowers and representing a special pressure gauge that, in fact, checks the tightness.
If you do not want to spend money on its purchase, you can use a conventional medical tonometer, on which you just need to change the pressure gauge.
When using this device, pay attention to the indication.
If the pressure does not drop and remains the same for a long time, you can rest assured, as this indicates the tightness of the carburetor.
If the pressure begins to decrease after a certain time, then there are still problems.
They can be associated with damage to any parts of the carburetor.
Before running to the nearest repair shop or specialty store selling trimers and spare parts, try to figure out the problem yourself. Sorry for the banality, but the brushcutter carburetor is not a spaceship of an extraterrestrial civilization, and it is quite possible to repair it with your own hands. To be confident in your actions, read the step-by-step instructions provided in this article.
VIDEO
A visual inspection of the carburetor will help detect fuel leakage and air leakage, but the main reasons for the failure of the device lie inside. Therefore, in order to determine and most importantly fix the breakdown, the carburetor must be disassembled.
It does not take much effort to disassemble the carburetor of the brushcutter.
It is enough to unscrew four screws on one side
and two on the other. This can be done using a regular Phillips screwdriver. Unscrew the screws carefully and fold them to the side. They may be needed during assembly. It is advisable to cover the table with a white cloth before disassembly so that everything is visible, even the smallest details that may fall out during disassembly.
We start disassembling from the side of the fuel supply system.
We remove the primer - a pumping bubble, which is remarkable, it is simply impossible to install the carburetor parts incorrectly during assembly. Products have characteristic ebb and flow.
Now we remove the membrane. It is she who performs the function of pumping fuel into the carburetor.
When the membrane vibrates, the other side exerts pressure on the rocker arm of the mechanism and the needle rises, which, in turn, opens the hole and fuel is supplied.
Remove the carburetor cover with the injection mechanism.
Further, another membrane is installed. We carefully remove it.
There is another gasket under the membrane. We also carefully remove it, without damaging it in any way.
Next, we move on to dismantling the parts from the back of the carburetor. As mentioned earlier, we unscrew the two bolts. This is already an air supply system.
A valve is located here, which, when gas is added, opens and increases the flow of air into the engine.
After removing it, a bare body remains in the hands. The carburetor is disassembled.
Identification of faults and their elimination
Now it is worth paying attention to the problems that occur during the operation of the carburetor and how to fix them.
The first thing that happens is that the holes and jets in the fuel supply system are clogged with dirt. Filters installed in the tank and directly in the carburetor do not help. They still allow small particles to pass through, which cause brushcutter failure.
Now we need to get the needle.
To do this, unscrew the bolt on the mechanism, holding it with your finger. The fact is, there is a spring there and a careless action will lead to the fact that it is lost.
We take out the needle, see photo and spring.
How to purge.The most effective way is to use an ultrasonic bath.
It is filled with either a special liquid or gasoline, a carburetor is placed there and under the action of ultrasound, the so-called cavitation effect, the channels are cleaned of contamination.
The second option for cleaning is compressed air.
You can use the compressor available on the farm and clean the carburetor channels. However, this method is effective if the contamination is not very large.
If there is neither an ultrasonic bath nor a compressor at hand, then cleaning can be done in the third way using a special cylinder for cleaning the carburetor. They are sold in almost all car dealerships and supermarkets. The price is not high and is about $ 2-3. Enough of such a cylinder for 4 or 5 purges.
Now we need to blow through the channels in the body and carburetor cover. See photo.
Another particle of dirt can get stuck under the needle. See photo. This will also lead to brushcutter failure.
Important! When cleaning the carburetor, never use needles, pins or wires. Even the slightest scratch will damage the carburetor. It will have to be changed entirely.
It is located on the carburetor cover and is a fine metal mesh. Its pollution occurs very often. This is due to the deposition of oil, additives, dirt on it.
Sometimes, when disassembling on the nets, a certain film is found. Therefore, the carburetor does not have enough fuel and the brushcutter either does not start or works intermittently. The cleaning methods are identical to the first reason: an ultrasonic bath, a compressor or a spray bottle with a special solution. In addition, if the mesh is clogged thoroughly, you need to take a soft brush for watercolors, soak it in gasoline and rinse it carefully without damaging it.
They have the ability to wear out during operation. From prolonged use, they deform, stretch, lose elasticity, poor-quality fuel corrodes them, and can no longer perform their functions well. This also applies to the needle itself. The fact is that it is covered with a thin layer of rubber, which wears out during operation and can no longer fit tightly into the hole. The brushcutter starts to work intermittently. To eliminate such a breakdown, it is necessary to replace all worn out parts. Where can I get them?
In specialized gardening equipment stores, a carburetor kit for a brush cutter of a certain model is sold. The cost of such a repair kit ranges from 40 to 60 hryvnia.
It includes two diaphragms, a gasket, a needle valve and a spring.
All wear parts of the carburetor can be replaced. Therefore, you should not rush and buy a new one, and you do not need to run to the workshop either, repairs are within the power of any brushcutter user. Professionals claim that the quality of the components in the repair kit even exceeds the characteristics of the native carburetor parts. Therefore, a well-repaired unit will perform better than a new one.
In addition, the bubble button for manual fuel pumping may fail. The effect of gasoline on it leads to the fact that during prolonged operation, the rubber corrodes and it begins to stick together or, under the influence of low temperatures, for example, during storage, it bursts. The button should also be replaced if necessary. In addition, its cost is small and will not affect the size of the repair budget in any way.
Based on the foregoing, it can be concluded that there are only three main carburetor malfunctions: clogging of channels, contamination of the fine filter and failure of components. In the first two cases, cleaning is enough, and in the third, a repair kit will help.
Assembling a brushcutter carburetor is a snap. All actions must be performed in reverse order:
Install a spring and a needle valve in the carburetor cover. Hold the spring with your finger and tighten the mounting bolt.
Screw the shutter of the air supply system to the product body with two screws.
Turn the carburetor over and go to the fuel system assembly. First you need to put the gasket.
Install the carburetor cover.
Install the main diaphragm.
Install the plate with the manual fuel pumping button and tighten the four screws.
The carburetor is assembled and ready for further use.
For the first time, repairing a brushcutter carburetor may seem like a complicated process, but if you have to disassemble it a second time, then this procedure will not cause much difficulty.
Video (click to play).
If you did not find any of the listed problems in your carburetor, it is recommended to contact a specialized service for help.
