DIY Philips hair clipper repair

The simplest models of hair clippers are designed in much the same way as Soviet-style razors. The difference between them is that in modern models of machines, a pendulum-type vibrator is used, so the trajectory of the blade is not horizontal, but arched. But even the highest quality and most reliable electrical appliance tends to break down over time. Topic of the article: hair clipper - DIY repair.

The design of these devices is not particularly complicated, therefore, there are no particular difficulties during repairs. Here are the main components of such a device:

• Steel core transformer.
• Stator coils - 2 pcs.
• Cutting tool.
• Vibration mechanism.

As you can see, there is nothing complicated. If the breakdown is not very difficult, you may be able to cope with the problem yourself and not have to contact the master.

Let's take a look at what it takes to fix a hair clipper. The most common reasons that the appliance refuses to cut are as follows:

• Engine breakdown.
• Power supply problems.
• The knives are dull.

Important! Actually, if the knives are dull, the machine works, but it does not cut, but simply tears the hair. All one has to do in this case is to sharpen them.

Before starting to repair the device, carefully inspect it. The inspection procedure is as follows:

• Inspect the cord for damage or loose plug. If there is damage, it is much easier and safer to replace the cord.
• Check the voltage at the block built into the housing.
• Call switches and switch. If these parts are out of order, they must be replaced.

The most common malfunction is the deterioration of the coils. There are 2 repair options here: rewind or replace.

Important! Of course, it is easier to replace, but you need an absolutely identical coil with exactly the same number of turns as was originally in the unit. It may not be on sale.

Rewinding is a matter that requires patience, but feasible even for a student. Rewinding can be done with a drill or even manually. The biggest difficulty is not to be mistaken with the number of turns.

Important! More or less turns can negatively affect the power of the device.

As for power outages - believe me, in many cases the problem is not with the typewriter. If your device is running on battery power, then it may well be time to replace it. If the machine is networked, then the following options are possible:

• Make sure there is light in the apartment.
• Plug the appliance into a different outlet.
• Examine the plug and cord. Replace them if necessary.

Important! After the repair is completed successfully, remember to adjust the position of the knives. To make the process go faster and the result is high quality, use our instructions for setting up your hair clipper.

For sharpening, you need a special circle with an aluminum disc. The procedure is as follows:

1. Wash and dry the surface on which you will sharpen your knives.
2. Pour abrasive on the prepared surface, level it.
3. Place the knife strictly along the radius of the disc, clamp it in a clamp, and then start the circle.
4. Treat the knife with a special solution and lubricate.

Important! There are other ways to sharpen. You will find step-by-step master classes and useful recommendations for solving this particular problem in a special article of our portal of useful tips "How to sharpen clipper knives?"

If the head is not set correctly, the machine works, but very badly.Here's what to check in this case:

• Amplitude of movement of the knife.
• The location of the knives relative to each other. You can adjust them using a regular screwdriver.
• Centering the blade cover.

Important! We must not forget about prevention. If the device has a simple device, then it will rarely break. This fully applies to hair clippers. But this does not mean at all that they do not require any maintenance. They need to be cleaned and lubricated regularly.

If it turns out that the device cannot be repaired, do not rush to throw it away. In a separate post, we have outlined some interesting ideas for what you can do with a hair clipper.

As you can see, you don't have to go to the store for a new device at all. In case of any malfunction, you can eliminate it on your own. You just need to understand the cause of the breakdown and take the time to repair the hair clipper.

Simple models of clippers are practically no different from the usual razors of the times of the USSR. The only difference is that in modern models of clippers, the vibrator is pendulum, so the blade does not move horizontally, but in an arc.

Before you repair your hair clipper, you need to understand the internal structure of the device. At first glance, the design of the machine is simple, without technological bells and whistles, so difficulties in the repair process are not expected. Internal structure of a hair clipper:

• voltage transformer;
• steel core;
• two stator coils;
• vibrating mechanism;
• cutting unit with self-sharpening blades (includes movable and fixed parts).

The pendulum or swing arm is fixed with springs on the sides. Plus, the pendulum is mounted on a bearing (one of the vulnerable spots that can easily crack). The movable part of the cutting mechanism is made light, thanks to the combination of different materials - plastic and metal.

The device of the coils is simple, any boy can handle them. You just need to buy a wire of the required length, make a primitive rewind device and start repairing. The coils fall evenly from one edge to the other; they do not need to be fixed. If a person has minimal knowledge in the field of electronics, it will not be difficult for him to repair and assemble a hair clipper on his own. It will be more difficult for people who do not know the rules for handling tools for electrical work. But having studied the theory, you can safely begin to translate your knowledge into practice.

The hair clipper is an indispensable tool for both professional hairdressers and “home hairdressers”. These clippers are classified as household and professional. But both those, and others, sooner or later fail. Typically, this unit is repaired by power tool repairmen, for example, in a household. But some machine malfunctions can be repaired with your own hands. Before starting the search for breakdowns, if your tool does not work well, you need to have an idea of ​​the internal structure of this clipper.

There are 2 types of hair clippers, which differ in their principle of operation.

This type of clipper is the most expensive hairdressing power tool on the market and is available in two versions: mains powered and cordless. Rotary machines are distinguished by their reliability, great power and durability. The main driving element of this apparatus is an electric motor, on the rotor of which an eccentric is put on. When rotating, the eccentric, connected to the movable knife, moves it in different directions. Also, the device has a knife block, consisting of a fixed part and a movable one.

In a stand-alone version, the tool body contains accumulator battery (Battery) and control board.

This is a more budget-friendly option for hairdressing power tools than the one discussed above. In this unit, instead of an electric motor coil installed... A pendulum containing a permanent magnet is located in front of the coil. When current passes through the coil, the polarity of the magnetic field changes at its core with a frequency of 50 Hz. Therefore, the permanent magnet in the pendulum changes its position all the time, and since the latter is connected to a movable knife, it starts to move. Also in the device you can see the power button.

The search for breakages in clippers may differ depending on their design features.

Rotary device malfunctions:

• breakage in the head of the nozzle block;
• failure of the electric motor;
• breakdown of the control button;

• problems with the network wire;
• eccentric wear.

Battery unit malfunctions:

• the battery life has expired, or it is faulty;
• the power supply is out of order;
• problems with the cord going from the power supply to the device;
• burned out control board;

• mechanical failures in the knife block.

Vibration machine malfunctions:

• breakage of the coil winding;
• loud noise;
• defective network cable;
• breakage of the power button.

In addition to all the problems listed, there are breakdowns that are inherent in all types of hair clippers: the tool does not cut at all, cuts poorly, with gaps, tugs or chews hair.

First of all, if your hair clipper does not turn on, you need to check the presence of voltage at the outlet, as well as check the power cord and plug.... It is very simple to check the voltage in the outlet: plug any electrical device into this outlet. If it works, then there is tension. Next, you need to check the plug: if it is collapsible, then you need to unscrew it and make sure that there is good contact between the wire and the pins of the plug. If it is non-separable, then you will have to disassemble the unit and ring both wires with a tester.

A common reason why the machine does not work can be a faulty power button. In addition, you should make sure that the wires are not unsoldered from its contacts.

In the case when the button, wire and plug are in order, check if the contacts inside the device, going to the motor or to the coil, are not unsoldered. If no problems with the contacts are found, then you will need to ring the windings of the electric motor or coil.

If it stopped working rechargeable hair clipper, then first of all, the operability of the power supply is checked. Next, you will need to check the battery inside the unit housing. In the event of an inoperative battery, it will have to be replaced with a new one, since the battery cannot be repaired. If the power supply and battery are in order, then the control board (if any) is called.

In case of malfunctions caused by mechanical damage internal parts of the unit, the electrical part of the unit will start. Therefore, the breakage is looked for in the head where the knives are located, or in the block where vibrations are created. This can be a problem with the eccentric (in inexpensive models it is made of plastic, it wears out quickly), or a breakdown of the pendulum at the point of its connection with the movable knife.

If you notice that the device chews or twitches the hair while cutting, causing inconvenience, then it's time to take care of sharpening knives... It is better to entrust this procedure to a specialist who has special equipment for these purposes. Attempts to sharpen knives on their own usually result in them being thrown away. If the machine has stopped cutting, you will need knife adjustment.

Do-it-yourself repair of the hair clipper is quite possible with some malfunctions, the elimination of which does not require special knowledge and skills. At home, you can make the following repairs.

This problem sometimes occurs when clogged rotor of the motor or eccentric... At the same time, they are jammed, the motor heats up and may hum a little.It is necessary to disassemble the housing of the unit and clean the rotor with an eccentric from dirt, then assemble the device and try to turn it on again. Also, if the device fell, then in this case a power cut may occur, which is supplied to the motor. It is necessary to open the case and check the soldering in the places where the conductors are connected. If the wires come loose, solder them.

The cause of the breakage may be in the power cord or plug. In the case of a battery-powered device, the problem may lie in faulty wire or in the power supply. It must be disassembled, check all contacts and ring the coil windings with a tester for an open or interturn short circuit. If these problems are found in the coil, the power supply will have to be replaced with a new one.

This problem may appear when voltage drops in the network... Therefore, in some devices there is a special regulator with which you can set the optimal operation of the device. Also, increased noise may appear when damage to the casee.g. after a fall of the machine. It is necessary to open the case and check it for cracks and how rigid the coil is holding. If the power tool is dropped, the coil fasteners could break off, causing severe vibration and noise. Sometimes the screws holding the coil can loosen spontaneously. In this case, they must be tightened without applying excessive force, otherwise the screw seat can be ripped off, and it will begin to scroll.

Most clippers are not much different from old Soviet-era razors, reminiscent of modern mesh models. The vibrator is pendulum inside, the blade makes not strictly horizontal translational movements, describing a large arc. One position: the edges of the movable and fixed knives coincide, they will be parallel, on the opposite side, a slight angle is noticeable. Normal, not in any way a malfunction. Do-it-yourself hair clipper repair is tied to small AC motors, mechanical part. Adjusts the clearance of the cutting edges.

We hope to teach you how to fix a hair clipper. The question is not trivial, as it seems at first glance to be deceived by the apparent simplicity of the design. Surprisingly, the only book describing the repair of hair clippers belongs to the pen of Lepaev and dates back to 1970. Loss of interest, simplicity of design? There are few professionals, there is no time for writing manuscripts, pressing matters are pestering. Regardless of how the hair clipper works, there are:

1. A transformer, the primary winding of which is often designed to work with voltages of 127, 220 V *.
2. Stator coils. Two according to the number of supply voltages.
3. Steel core.
4. The wings, pendulums, and another similar mechanism that begin to vibrate when an alternating field appears.
5. Knife block formed by movable and fixed parts.

• Switching power supplies have gradually replaced bulk transformers with laminated cores. The small size of digital technology has attracted clipper designers.

Whether there is a pendulum (Moser) inside the hair clipper, a curtain, both are held by two returnable edge springs. The stator does not touch the rotor, otherwise, while working, it gave out a grinding sound. A special screw mechanism will serve the regulatory purposes. The pendulum is often mounted on a bearing. Fails - noise will be heard. The moving part is made as light as possible, the knife can sit on a plastic part (the specific gravity of the polymer is several times less than that of steel). The pendulum may crack in the bearing area. Previously, you had to install a clamp, change a part, today's adhesives will firmly take on. Try Titan.

Hair clippers delight with coils. Ordinary chokes, a schoolboy will wind.Find out the brand of wire, buy a piece of the desired length covered with varnish insulation on the market, make a rewinder, start repairing the hair clipper with your own hands. The old coil is ringing. It will help to make sure: the malfunction will hide here, not the mechanical part. Burnt out transformer (not pulse), rewinding is not difficult. The second step is to lay the turns. A device is used made up of two pairs of racks located opposite each other on different edges of a long board. The axles of one support the old coil, the other accepts the wire. Noticing a break in the beginning or end, postpone buying a new wire on the market, wind back the existing one, subtracting the torn off part. It is important to maintain the correct number of turns, the location of the leads.

The winding of new coils is carried out with the described device. The coils fit tightly, there is no glue, the wire is held by hand. The pull helps to lay the coil with the wire in even layers. The turns are laid down by the shuttle method, from one edge to the other. After the end of the procedure, you need to ring the coil, make sure that the wire is intact. If one voltage is used at home, a longer wire from one unnecessary choke is used to restore the burnt one. Enough length - the market will wait.

The device of a hair clipper is ingenuous. Engine, torque transmission chain. The anchor of the hair clipper rarely breaks except in the case of the crack discussed above. Lubricate, clean the device, prepare yourself regularly. Apply VNII MP - 260, soft brush. The movement of the armature is sometimes adjusted with a screw, make sure that in all positions the teeth of the moving part do not protrude beyond the bed.

In many instances, there is a trimmer that takes energy from the same motor through a transmission.

First, the cord is inspected, the first step is to eliminate a significant part of the breakdowns. Inside, a block is often screwed into the case, you can check the presence of a supply voltage with a tester. In the second turn, the switch, the voltage switch, rings. If necessary, the problem is eliminated (if parts are missing, short-circuit the contacts). Particular attention is paid to soldering.

When the hair clipper does not work satisfactorily, the matter is explained by the incorrect setting of the head, it is time to inspect and lubricate the product. The return springs are worn out. By the way, the tensioning mechanism is also adjustable, if the amplitude of the knife movement is incomplete, pay attention to this detail. There are specific points. The blade guard must be centered on the hair clipper body. If this is not the case, the parts are fitted to each other by filing. Pay due attention to the adjustment of the relative position of the knives. At Moser, for example, you will find a slotted screwdriver screw on the side that adjusts the correct clearance. The clipper may not work at all or cut perfectly depending on how correctly the control is turned. Samples are carried out on a material that resembles wool.

The knives are positioned so that the edges of the movable and stationary go flush. For pendulum models, the adjustment position is selected when the tines are parallel. When tilted, one side will be lower than the other. To adjust the relative position, Moser has two screws that support the fixed part. The assembly hangs on the holder. The bolts are loosened with a screwdriver, after which the exhibition takes place in the right way. Then the fasteners are tightened. In the case of a slotted screwdriver, use the widest tip possible, the iron is not hot, it will be damaged when twisted.

Knives are often dull. Special machines are engaged in sharpening. They look like a potter's wheel, an aluminum disc. To begin with, the surface of the table is thoroughly cleaned and dried. After that, an abrasive is poured on top, leveled with a flat plate over the area. The knife is located on the disc strictly along the radial line. A laser pointer is built into the sharpening machine.The knife is clamped with a special clamp, the circle starts. The master gently presses from above, the sparks should fly in the direction of the teeth. At the end of the procedure, the knives are washed in a solution and lubricated. The test is carried out on a piece of wool or other material that resembles hair.

The design nuances cause small differences that characterize the self-repair of do-it-yourself clippers. At Moser, Torx screws are often used in the knife block, and the return spring is one double-sided.

The steel spiral is hooked with its ears on a movable knife, which is inserted into the anchor during installation. The cutting level regulator presses on the same spring, adjusting the position of the knife. There are no coils at all in these models. Inside there is a motor equipped with an eccentric shaft. By moving the stem, the knife goes back and forth. Accordingly, there are no magnets inside, the knife is extremely light, due to which the efficiency of the device increases (the inertia of the movable block is minimal). The power board supplies the (externally collector) motor with voltage. Checking the performance of the motor is as easy as shelling pears - ring the windings, the resistance should be in the order of tens of ohms.

The board is assembled on microcircuits and is powered, among other things, by a battery. To replace the source, you will have to get hold of a Torx screwdriver for a seven, after removing the case, all the necessary operations are performed. The battery itself resembles finger-type batteries, assembled in a bunch of three, but in fact it is easily charged from the AC mains through the adapter. It is clear that there is a switching power supply inside, on this issue you can go over on our website, there are quite a few articles posted where the procedure is considered.

In short, inside there is a number of input filters through which the voltage is supplied to the key element (transistor, thyristor, less often a relay). The control signal is generated by a high frequency generator. Due to this approach, it is possible to reduce the weight and dimensions of the transformer. Actually, the technology is still used today in power supplies. This applies to cell phones, laptops and other household appliances. In this sense, repairing a dog clipper is no different from high technology. What can break here?

• Diode bridge.
• Filter capacitors and resistors.
• Transformer.
• Key (transistor, thyristor).
• Generator.

There are also Schottky diodes at the output. Chosen for low voltage drop across open junction. Thus, repairing do-it-yourself hair clippers requires basic knowledge of electronics. That's all for today! We sincerely hope that we are helping readers overcome their fear of household appliances.

How to set up your hair clipper yourself. How to position the knives correctly. In this case, it is produced.

If the hair clipper has stopped cutting, this does not mean that the knives are dull and need to be sharpened.

What to do if the Moser 1400 hair trimmer starts buzzing. In this video there will be a couple of tips how to do it yourself.

hair clipper Moser ChromStyle 1871. The native battery costs about 1100 rubles, and the control board costs 2000 rubles.

Hair clipper repair. The machine began to turn off quickly, obviously the batteries are dying out. We disassemble and change.

In this video, I will show you how to properly adjust the blades relative to each other in order for the machine to be good.

In this video I show how in MY case I was able to restore the work of the hair clipper. Pay for.

How to set up your Domotec hair clipper correctly. Vitek.

Replacing the battery with a lithium one.

Typewriter (pulls and bites hair)

Another reason for the strong hum and vibration of the clipper. Manufactured by Sapir SP-1810A. Germany. Assembly marriage.

In this series, let's take a look at the Moser ChroMini mini trimmer. Problems with charging and turning on. There is not much to break in it.

In the next video I will show how I changed these batteries for one Li-Ion 18650 and what came of it. Analysis.

How easy and simple it is to sharpen knives on a clipper at home. Children's developmental channel.

We assemble and repair our own hair clipper Moser 1230.

Replacing the engine brushes with better ones!

Hair clipper easy repair no cost screwdriver set https://ali.pub/25vy42 tweezers https://ali.pub/25t6iw.

Urgent repair of hair clippers. Farmer's Channel: Ork Tv.

ER 508. Dropped hair clipper on the floor. The blow is not strong, but it stopped turning on. I am looking for the cause of the breakdown.

If anyone is engaged in cutting their own and not only hair at home, they know about the presence of such machines for cutting hair.

How to increase the effectiveness of a new hair clipper several times in 15 minutes with your own hands or.

LASER SHARPENING IS A LONG WORK AND THE LIFE OF YOUR TOOL. Laser - very precise factory.

The German hair clipper turned out to be crammed with electronics and behaved as if it were not lost on the board. On the.

Repair of the Moser hair clipper.

Repair "mini lawn mower"

Do-it-yourself Grundig hair clipper repair. Eliminate power wire break.

Asked to see a hair clipper. The reason is not working. Trying to fix the situation with our own hands.

If the video helped, subscribe to the Channel!

Review of clipper and haircut with true jokes =) / Subscribe to our new group VKont.

Broken in the place indicated by the arrow when using the device not very often.
The decision is really moronic, but marketers do not get their salaries in vain.

In other versions, these thin plastic guides are not present and the movement of the blade is limited by the spring itself.

Searches on Ali and other ebays did not give positive results for this particular model.
I had to fix it.

Although not, there are results, but this attachment stands alone, like the whole machine as a whole

Dimensions can be removed easily and simulated quickly (though I had to "adjust the backlash")

Another little thing printed on a working printer: a whistle. In fact, this is already the second attempt to print.

Good day to all. I realized that I am such a lazy and greedy person that I am too lazy to go to the store and buy.

Good day. For a short, but extremely laborious way of comprehending 3D printing, it has accumulated.

There are Moser machines that cost the same but are designed for hairdressing salons.
So they have everything done brutally, iron, on screws

It's just that one device is made to work for a long time, and the second to sell and break down within a given period.

I met a similar thing in other devices from Europeans with the mark “made in china / vietnam / indonesia” (still china).

I did not immediately understand the reason for such breakdowns.

This is the “cheaper” version, here I agree.

However, the constructors meant here. Another plastic material, more elastic and "slippery" to the touch,
teflon-like (fluoroplastic-like)
it is usually ivory for long-term use.

In your photo - this plastic part is clearly milky-white, it does not change its color, and - MORE HARD THAN THE DESIGNERS PLANNED.

Well, all your other conclusions are also correct - brand device, “mileage” - small, physical destruction, etc. etc.

Your solution is correct, and a very simple and beautiful implementation.
Thanks to!

about the beauty and health of hair

I would like to see a photographic image. ... However, it seems that on the back side there is a screw hidden by a sticker or a seal - having turned it out - you can disassemble the case into 2 parts and get to the electrical input. ...

Here such questions kill. we take and disassemble with a tool with our hands while using our head

do not forget that you will need to collect it later

Not a single screw is present.
1. The pads are removed with a thin flat screwdriver (fastened with plastic “crosses” to the body) perpendicular to the machine body.
2. The plastic part with knives is also pry off with a sharp screwdriver.Keeps on 4 clips, can be removed easily.
3. The metal plate under it is also pry off with a screwdriver (4 fastening latches).
4. The body itself is on 4 latches with several welding places. I forged the joint of the cases from the side of the cord and with the tip of a screwdriver “opened” it towards the knives. First one side, then the other.
The mountings remained relatively intact. Gathered back.

The brushes are removed. Look, try.

There's a thin soft metal-only to be discarded.
It's cheaper this way

1. Remove the head with knives from the machine. It should unfasten easily.
2. Memorize or sketch the insides of the head.
3. Detach, snap off, pull out and shake out the insides.
4. We clean everything, rinse in cologne and assemble in reverse order.
5. Lubricate the insides and put the head in place.

the body of the machine itself does not need to be disassembled. just unscrew the two bolts on the knives. remove the blades and clean the space under them with a brush, and so are the knives. grease and reassemble as it was. they are slightly regulated. expose so that the knives are parallel.
I'll tell you a secret. she does not cut your hair, not because the hair got in, but simply the lubricant ran out. )))
if the machine is not professional, then the lubricant is enough for a couple of haircuts. nonsense and not cars.

Hair is an adornment of the head, and according to its condition, you can make a certain impression about a person, draw some conclusions. To make your hair look a worthy decoration, it needs regular grooming as well as occasional haircuts. Nowadays, hair cutting, as well as hair care can be offered by various beauty salons and hairdressing salons, but there is not always an opportunity and free time to visit them. Therefore, many people prefer to master the skill of a hairdresser and tidy up their own hair and hairstyles of relatives and friends right at home.

In this case, a Philips hair clipper will become a good master at home. This is a great option to cut evenly the hair at the back of your head and around your ears. The machines are not only intended for men's haircuts, they are versatile. You can also get your child's hair cut, because sometimes it is very difficult to get children to go to the hairdresser, or to trim and touch up a woman's hair.

• in the machine there are fewer upper movable teeth than lower fixed ones;
• fast forward movement of the machine is not recommended, because at high speed, the upper plate moves more slowly, and the machine does not have time to cut all the hair;
• it is impossible to take the machine away from the head with a sharp movement, this can ruin the hair caught between the teeth.

In the past, the clipper used to cut hair resembled scissors without adjustments, the hair was cut using the movement of the fingers, but the quality left much to be desired.

There are several types of Philips hair clipper:

• rotary (works with a motor, without stopping, has a powerful engine, does not heat up, is equipped with an air cooling system);
• vibration (the engine is powered by an electromagnetic coil, with the help of which the blades begin to work, has a limited operating time, is cheaper than rotary ones and is not suitable for a professional haircut);
• rechargeable (work is carried out from the network, as well as from the battery charge that comes with the kit);
• pendulum (3-4 models have been produced in total, it is not popular).

Today, many are interested in a quality hair clipper. St. Petersburg is a city where you can buy products from different companies. Today there are many companies that have hair clippers in their assortment. One of the largest, dynamically developing manufacturers, which is known all over the world, is Philips.

The Philips hair clipper is affordable, comes in a variety of styles, and the quality is excellent. A wide selection makes it easier to trim at home. The Philips hair clipper allows you to create any hairstyle with different hair lengths.With the help of an additional attachment, you can touch and trim your beard.

Philips' rounded blades and combs protect against damage at the time of use, there are several settings for specific hair lengths. The articulated head swivels 180 degrees for complete control and easy operation. This Philips hair clipper has a sleek, beautiful design and shape that makes it comfortable to hold in your hand. The set includes attachments for different hair lengths. No special maintenance and lubrication required. This is a great value for money option for creating a neat and fashionable haircut.

Advantages: compact, lightweight, inexpensive, convenient

My husband doesn't like going to the hairdresser. And it does not allow me to show the skills of a hairdresser myself - he says that I have been cutting my hair for a very long time.
So we decided to buy a hair clipper to whack-whack, and that's it.
The machine was chosen as the simplest one, without any additional functions, such as trimming the hair in the nose. We decided that the main thing for us is to buy a product from a well-known company with a quality guarantee.
We opted for Philips QC 5015 - an inexpensive machine with self-sharpening knives, battery operated. The nozzle moves smoothly, allowing you to adjust the hair length up to 2 cm. Maybe not enough for someone, but even with a margin for us.
The only thing that may turn out to be its drawback is that the machine cannot be disassembled in order to properly clean the hair that has got into it. Although, in my opinion, they are well cleaned with a brush.
In general, we are very pleased with the machine. Now you can “go to the hairdresser's” right at home at least every week.

Hair clippers are actively used by hairdressers to create stylish hairstyles. Where the hand with the scissors can flinch, cutting off the excess, the technique will not fail. Moreover, such devices are applicable in everyday life when the hand does not have the necessary firmness, if you need to quickly trim your husband's slightly regrown hair, for example.

The modern market of hairdressing equipment offers a wide range of models, from the simplest household to professional with various operating modes and a wide range of attachments. Attachments that allow you to embody a variety of ideas when doing hairstyles. In fact, these are the same razors that were widespread in Soviet times, with minor changes that transformed the device and made it more convenient to work with hair.

However, it is difficult to find a technique that would never break. Repair of clippers in Kiev is no exception. As a rule, repairmen have to deal with the same faults and breakdowns. Here are some of them:

Broken wire at the junction with the body. This is one of the most common problems. During work, when everything needs to be done quickly, hairdressers rarely monitor how the wire is located, whether it has any kinks. With this type of damage, a short circuit often occurs.

Split plastic case. In most cases, this material is rather fragile, which sometimes can significantly reduce the cost of equipment. As a rule, the case can be restored in this case, but there are times when you cannot do without a complete replacement.

Broken switch. May fail due to burned contacts. If the internal plastic parts break, the switch must be replaced.

Often the machine becomes unusable due to the wear of the parts that are responsible for the movement of the knives. The machine may work outwardly, but the haircuts will not work.

Some types of toy cars can make noise. At the same time, only the master is able to accurately determine the source of the noise. Do-it-yourself repair of clippers can be significantly delayed. In some cases, the body or internal parts are damaged, in others, fine adjustment of the adjustment screw is required.

If the recommended rules are not followed during operation, the knives can quickly become blunt.And again, when sharpening, you cannot do without a specialized machine, which a home master hardly has. Clipper repair workshops, equipped with all the necessary equipment, will help solve this problem.

The foreman has extensive experience and can often determine the cause of the breakdown in a short time. It will not be difficult to find the addresses of the repair of hair clippers, where they will perform high-quality work - contact the representatives of "My Service" and we will help you in solving any problems