VIDEO
Doubting your knowledge? Do you think that repairing a zipper on boots with your own hands is too difficult? Then you have to go to the workshop. The cost of such a service is low, and the boots will serve you just like new.
Replacing a slider isn't that hard! If desired, it is quite possible to cope with it!
And I'll show you how easy it is to do it.
liked! now you don't need to ask anyone))
A very useful master class! Thanks!
Thanks! Now I know how! I will definitely use your experience!
huge thanks for MK.
Such a necessary lesson! How many times I regretted that I am not able to repair shoes myself, when you bring boots from repair, and they are ruined! And for your own money.
Great MK and very helpful.
Super. All the time I was arrogantly thinking - what is difficult! And the zipper itself was sewn into the jacket with the wrong side)
But we gained experience! Just be careful!
This is a really useful master class! Thanks!
As an experienced shoemaker, I will say that after such a master class you have a direct road to the workshop, and believe me, repairs will cost more, or you will have to change the whole snake :)
I change the runners in jackets in the same way and nothing happened!
Nirazu didn't reinsert the lightning!
So then the jacket, and then the boots. In shoes, the runners change only AFTER THE BOTTOM. After such a master class, I change dozens of snakes. After you cut it a little, it just breaks a little.
I change the sliders both from the bottom and from the top, and in 20 years of my work I have changed more than 1000 sliders and believe me I had no problems with replacing the sliders, but did you think how people at home will change the slider from the bottom? This is, firstly, and secondly, you need to take into account the situation when the zipper is glued deep under the sole, and what do you propose to open the sole for the sake of the runner? I saw very often how a master or type of master change the slider from the bottom, it was just ugliness! And by and large, if you can show people something better, then show it! The internet is limitless.
Everyone should do their own thing. If you do something, then conscientiously, and if you don't need to sculpt and take it. I also change the runners in different ways, depending on the situation and time, but you CANNOT CUT THE TOP EDGE OF THE SNAKE.Any self-respecting master knows this. The work should be done so that the result is visible, not how you do it. The only thing I agree about “a master or a type of master” is that a crooked-handed person will not do it all the same - ugliness.
I understand you perfectly, but you also understand people who have a problem with the slider! Not everyone has the ability, as well as the desire to rip and sew either from the top or from the bottom. Therefore, I showed the easiest way to replace it! against your opinion. I will not go far, 6 years ago I changed my wife 2 zippers in the same way. I still wear it without problems. It just seems to me that in this matter it is not too much with a cut, and much more depends on the quality of the lightning. And I will also note. that there are shoes into which one-meter zippers are sewn and not standard ones, in such zippers I do not cut, but unstitch!
The zipper is the smallest detail of our shoes, but for some reason it is very important.
It is called a dog, a clasp, although the original name is a slider.
This is often the case. We need to go outside very quickly, most often we rush to work in the morning. There are only a few minutes left before the departure of our bus. We jump into our warm boots, quickly zip up and "Wham!" a piece of the zipper remains in our hands. And the boots were never fastened.
What are we doing? Right! We run for a paper clip. Well, or something else like that.
Probably everyone has had to deal with such a problem. If not, then it will definitely collide.
Here's what you can get.
After all, you must agree that it is more aesthetically pleasing, nevertheless it will be much easier to close the zipper.
At least you can use such a dog for a while, and then go to the workshop.
And it can also be applied to our children's shoes.
Oh, how they love to break something, including parts of shoes.
And on such a repair of the zipper, you can save your home budget, because most often children buy shoes for one season.
It so happens that they did not have time to buy new shoes. And after a few days, these shoes must be carried to the workshop for repairs.
When fur gets under the slider when closing the zipper, it is difficult to move it further. But we do not always understand why the lightning suddenly began to close badly, and we continue to pull as long as we have enough strength.
Sometimes in this fight we win and the boot closes.
How can this be manifested.?
constantly sticks in a certain place
when zipper is zipped, the slider is partially zipped, and in some part the zipper begins to diverge
and, finally, the zipper holder comes off
To prevent this from happening, as well as to extend the life of the zipper, you need to do some actions.
If parts of the fur do protrude quite far, then be sure to cut them off.
It is necessary to cut off all the protruding fur along the entire length of the zipper.
It's better than repairing the slider later or completely fixing the zipper 🙂
Neither fur nor any protruding threads should fall under the zipper slider.
You urgently go to work or visit, you start to fasten the zipper on your boots, and it diverges. What to do? Catastrophe!
And it so happens that you have been suffering for more than one day, until you make several attempts to fasten your shoes. And for the tenth time, lucky, the zipper was fastened.
We can give a few more similar examples that arise with lightning, but let us dwell on these.
In fact, this problem is very simple to solve. Even at home and very quickly, you can repair a lightning.
Time factor, you have been using this shoe for a long time. That is, the zipper itself or the slider has worn out
Narrow boots in the bootleg and you fasten the zipper with great effort, which means that the slider is unbent
The boots are new or have recently replaced the zipper, they still come apart. This means an initially defective (weak) slider.
In all these cases, the problem can be solved immediately, but you need to understand that, nevertheless, this is temporary. In the first case, you can go through the whole season, in the second, after a while the lightning itself will just break, in the third, the slider will need to be changed in the near future.
Now let's start fixing the problem. To do this, you will need some tools, there are not many of them:
Pliers (or as pliers are popularly called)
Hammer
Round nose pliers, if required
A stool or any sharp and hard edge of something, then you will understand why (in the photo, instead of a stool, I usually have a boot's foot)
So, take your boot in your hands. Bring stools to the corner.
It is important that the base is flat and solid.
How to replace the zipper on your shoes? How to repair a zipper on a shoe?
Is it possible for yourself replace zipper , for example on a boot? With a strong desire, you can. Although the best option is to refer the boots to a good shoemaker, he will do it professionally and he has a special machine for sewing the seams on the shoes. If you decide to do the replacement yourself, then do everything slowly, carefully.
Prepare a new zipper , first, however, you need to buy it. If the new zipper is longer than the old one, then shorten it to the correct size.
Gently evaporate the old zipper , a sharp scalpel is better for this.
Delete remaining threads along the seam .
To make everything work out beautifully, neatly, it is better to glue the zipper first, and then just flash it. When we glue it, it is possible to make corrections so that it lies flat (the glue does not dry out immediately - it takes 2-3 minutes to fix it). First, it is good to smear the place on the shoes where the zipper will be located. And then there is a zipper along the edge, not reaching the teeth of 3-4 mm.
Begin to glue the zipper from the bottom, drive it into the corner by 1.5-2 cm and then glue it along the entire length of the bootleg. After gluing carefully on one side, let it dry for a couple of minutes and then proceed to glue the zipper on the other side.
We check how the zipper is glued. Also glue the lining to the zipper on both sides.
As everything is stuck, you can sew a zipper on a typewriter or by hand, hitting a needle into the holes of an old stitch.
The fact is, in order to replace the zipper on your shoes, you will not need weak hands, a tool that is capable of stitching thick material (a machine or an awl).
The zipper needs to be whipped at the beginning, I think it is not difficult to carefully cut the strings with a flat knife and pull them out.
Try not to damage the leather itself or the material of the shoe.
When you cope with this task, you need to go and buy the same one, neither wider, nor larger, nor thicker, but exactly the same.
Next, we insert the zipper into place, gluing it with rubber glue, this is in order to assemble shoes with a zipper that will already stand in place, then it will be easier to flash it.
So, carefully on both sides, we will mix everything as it was, insert the zipper and press it with glue - do not use any glue other than rubber! , rubber glue will not damage the shoes, and if it comes out somewhere and stains the shoes, it is easy to remove it!
Further, of course, it is good to have a sewing machine that is capable of stitching such a thickness, took it and stitched it and everything is ready.
But I am sure that you do not have such a machine and you will have to sew with an awl or a thick needle and pliers, stitch by stitch, sew everything as it was.
Use the old seam holes to make your task easier.
In general, the matter is very difficult but doable.
here is the seam that makes the boot hook, but with a needle, I think it's clear how to sew.
How to replace a zipper on the shoes? How to replace the zipper on boots?
Replace the zipper on the boots pretty hard. I have been sewing for a long time, and I changed the zipper on my boots myself, so I can tell you one thing - if you have never done this before, do not take it. I suffered terribly, but I was not satisfied with the result of my work.
You can change the zipper if you first flop the previous one. There are nail scissors, they will help you in this matter. Carefully evaporate, without damaging the skin, suede.
Next we take our lightning. It should be either the color of the boots' material, or just black. I like tone on tone more, because boots will look much nobler in this version, in my opinion.
Then we need to put some glue on the fabric of the lock. I would advise you to take "Moment" gel or hot glue. it is better to distribute the adhesive consistency with a synthetic bristle brush.
We glue. Now, I will voice an important point.
If there is fur inside the boots, then our task is to glue the zipper so that when fastening the fur, the lock dog does not “chew”. If the fur is worn out and becomes not beautiful at the edges, it can be carefully trimmed with scissors. Now let's see how we did it.
If all is well, we will try to flash the zipper.
I can honestly tell you that it is much easier to flash on a typewriter. If the machine is good, then it will sew thin skin without difficulty.
If you work only with a needle and threads, then the threads should be chosen quite thick. They are sold in a dedicated department.
We sew using an awl, a thimble. It will protect your finger and help push the needle through without hurting your finger.
I really hope so. that you will succeed.
But do not forget that there are workshops in which everything will be done quickly and efficiently.
Of course, you can independently replace the zipper on shoes, including boots, for example, winter boots. It is important to do everything carefully, unhurriedly.
First, buy a new zipper of the right size, even if it is long, it is not a big deal, you can shorten it.
2) it is advisable to glue the zipper first, and then just flash it. When gluing, you can safely lay the zipper in the place where it should be, if you sew it on right away, then it may not work out so smoothly.
3) Glue the place along the entire length of the boot with glue, and also apply glue along the edge of the zipper.
4) glue it from below, drive the zipper into the corner for a couple of centimeters, then along the entire shaft. Glued on one side, let it dry for a few minutes, then coat the lining of the boot with glue, the place that is superimposed on the zipper.
5) when the glue is completely dry, we sew the zipper, try to hit the hole with the needle in the holes of the old stitch.
The zipper on boots is no different from a zipper sewn into a jacket, and almost everyone knows how to rearrange the zippers. But the problem with replacing the zipper in winter boots is not the inability, but the lack of special equipment, because you cannot sew a zipper on a boot with a simple machine.
There is an option, to flash the zipper completely with your hands, sticking a needle and thread through the remaining holes, the work is not difficult, but jewelry, the costs do not pay off and it is worth buying new boots.
I suggest a slightly simpler option, it does not make the zipper durable, but it saves you until the next purchase. Why do we change the lightning - the dog jams, slips, breaks.
The dog can be secured with a paper clip or put in several layers of twisted thread in its place and make a loop.It lasts a long time, we change it three times during the season.
But if the zipper sticks or does not close, then you need to adjust the lock itself.
To do this, use nail scissors or a thin screwdriver to expand the space in the lock, bring it to the bottom of the zipper, re-clamp the lock with pliers and drive through the zipper. Here you need to take your time and feel how much you are pinching. If you pinch, the zipper will not be fastened. And if the zipper at the bottom remains not closed, you just need to alter the bottom with your hands, make a membrane so that the lock does not go over this line.
The method is proven and helps to solve the problem with lightning on any product.
Repair of women's boots
Since boots are a permanent and basic shoe of a woman's wardrobe in winter and autumn, it is not at all surprising that the zippers on boots diverge often and at the most inopportune moment. It happens that the tongue breaks, and it happens that the entire lightning comes into disrepair. If it seems that you do not know how to quickly fix a zipper on boots and shoes need to be sent to the trash can, then feel free to take the shoes to the shoe shop. And especially courageous citizens can try to make repairs with their own hands.
How to fix a zipper on boots so that you don't have to throw out your shoes?
If you decide to repair the zipper on your boots at home, then rinse the boot thoroughly first, especially the area of the footprint. It will also come in handy in case you do change your mind and take your shoes to the workshop. After all, shoemakers do not accept dirty shoes for repair.
After you've washed your boot and dried it thoroughly, it's best if the shoe dries naturally, you can start examining the zipper. You must determine the cause of the breakdown and understand what tools and devices will be useful for you to eliminate the breakdown.
One of the most common failures of a zipper is the breakage of the part of the slider - the part that is movable and fastens the lock. The tongue of the runner may also break, making the boot impossible to fasten. This problem can be solved very simply - attach a paper clip in the color of the shoe instead of the broken tongue and you can easily unbutton the boots. If you don't like having a clip on your shoe, you can remove it after you have buttoned or unbuttoned your boot.
Replacing and repairing the zipper runner of your favorite boots
If the slider is completely cracked and fell off, then you need to get a new slider and fix the zipper on the boots. On the back of the broken part, look at its number and pick up the same one in a sewing accessories store. First, remove the stopper before replacing the slider. Unfold it with metal nippers. But you don't need to break it. Subsequently, it will be useful to you. Next, put on a new part, and then the old stopper and gently clamp it.
If the stopper still breaks, which happens quite often, replace it with any small part that will prevent the zipper from coming off the zipper in the future.
If outwardly the slider looks intact, but at the same time the zipper is not fastened, it means that internal damage to the slider has occurred, for example, the restrictive runners that clamp the zipper are weakened. In this case, take a pair of pliers and gently press down on the slider at the edges where the zipper links meet. If such manipulation did not give the desired result, then to fix the zipper on the boots, remove the zipper slider and unbend the stopper. Squeeze the zipper, but don't overdo it so you can put it back on with the zipper. Then put on the zipper and check the functionality of the slider. If the result is again negative, then the slider will have to be replaced.
How to fix a zipper on my boots and when is it necessary?
Video (click to play).
If you have examined the boot and found that several links are missing from the zipper, which is why it does not fasten, then you will need to completely replace the zipper.First, match the size and color of the zipper to the broken zipper, carefully open the seams and pull out the old zipper. Install a new one in its place, sweep a new zipper, pay special attention to the beginning and end of the zipper. In these places, the zipper should be fixed very well. But it is best to sew a new zipper on a typewriter. There is a special zipper foot. The seam that connects the zipper and the boot must be smooth and even, without bends or creases, otherwise the functioning of the zipper will be difficult.
