DIY repair of an inflatable trampoline on a seam

In detail: do-it-yourself repair of an inflatable trampoline on a seam from a real master for the site my.housecope.com.

If the children's trampoline began to deflate quickly, this is not a reason to throw it away. Let's see how you can glue it at home.

To eliminate punctures, cuts and other defects, the following materials and tools will be required:

Scissors,
A brush with thick bristles,
Roller or elastic roller,
Solvent,
A piece of PVC (patch),
Special glue (we will analyze it below in the article),
Mounting hairdryer,
Sandpaper.

All tools can be bought at any hardware store.

Choosing the right glue is especially difficult for many people. Some manufacturers attach a ready-made repair kit to the trampoline, which already contains everything you need, including a tube of glue.

If you do not have such a repair kit, in stores, pay attention to the following adhesives:

Desmokol is a polyurethane glue well known to shoe repairmen. Reliably holds together not only PVC fabric, but also plexiglass, rubber, plastic and other materials.
Vitur - is similar in composition and properties to Desmokol glue. Designed to work with PVC, leather and leatherette, linoleum, wood, plastic, rubber. Differs in water resistance, seam strength, non-toxic.
Uranium is a polyurethane adhesive used for hot and cold bonding. The seam is elastic and moisture resistant.
Moment for PVC - Used to repair PVC boats, but can also be used to repair trampolines.

Now knowing how to glue a children's trampoline, you can proceed directly to the repair.

Algorithm of actions for those who want glue the inflatable trampoline at home:

Video (click to play).

We clean the place of damage from dust and dirt and go through with sandpaper for stronger adhesion.
With a rag soaked in solvent, carefully wipe the area with the defect.
We cut out a small patch (slightly larger than the damaged area) and also sand it and wipe it with a solvent.
Apply glue in thin strips to the place where we will glue the patch, and distribute with a brush or fingers.
We join the canvas in the place of the defect, apply a patch on top. Smooth it out with your hand. We expel the air from under the patch using a roller or an elastic spatula. Leave to dry for a couple of minutes.
Using a mounting hairdryer, we warm up the ends of the patch well, moving along its perimeter. We try not to overexpose so as not to burn the material. The ends will melt to the base; all that remains is to carefully iron them with a rag.

We put any heavy object on the repaired site as a press and leave it for a day for better coupling.

VIDEO INSTRUCTION

All work is carried out on an ideal level and solid surface and only on a trampoline in an inoperative state.
You need a little glue. The adhesive layer applied to the surface should be practically invisible.
In no case should PVC material be heated with an open fire - it will melt quickly.
PVC patch can only be applied on the wrong side (matte side).
To prevent damage to the material, use the trampoline strictly in accordance with the manufacturer's instructions, and then it will serve you for at least 3 years.

Self-repair of an inflatable trampoline is quite possible to do at home, but if a repair is needed urgently or you doubt your abilities, you can contact a specialist.

In pursuit of work at the exit trade on May 1, I would like to say a few words about breakdowns. After the winter, we pulled out our equipment and it became clear how badly some of the rides needed to be repaired!

What breaks most often - let's list:

the protective round foam rubber covering around the trampoline perimeter breaks - it covers the springs to prevent falling on them. This coating for all trampolines quickly deteriorates: for cheap ones it breaks, for more expensive trampolines it stupidly fades
the racks on which the mesh is held are bent - on average, they are bent by 3-9 degrees. Not much, but it is noticeable from the outside.
The foam insulation on the racks is torn. To prevent children from bumping against the racks (they are metal), the metal is covered with foam rubber. Due to the constant assembly-disassembly of the structure, this foam rubber quickly breaks - you can see this in the video.
All fasteners wear out and are lost - small things, in principle, are always lost =))) And wear is a low quality of metal. The thread is cut off, which makes it difficult to tighten the nut, it just scrolls.
The fencing mesh is constantly torn - it is made of the same material as the mosquito net, that is, it is not particularly strong. If suddenly a child flies out of the trampoline, he falls on the net - and now it is already torn!
The legs of the trampoline are wiped - if you are too lazy to disassemble it and you prefer to take it for storage at night, then be prepared for the fact that dragging the lower surface of the legs over time from dragging on the asphalt.
Loss of springs is the biggest trap! They are inexpensive, they just don't really sell anywhere! However, even without 1-2-4-6 springs, you can work. It just doesn't need to be advertised and it is necessary to distribute the missing springs evenly.
Fabric fading - I originally had red racks and a blue coating around the perimeter. The flooring turned blue and the uprights a pale pink. The sun does its job - everything fades.
The worst thing is if your weld seam on the frame tubes cracks. There are tubes there, which are attached to the legs with a jib, it is welded "end-to-end". If there is a crack, then it is problematic to weld it: usually trampolines are made of aluminum, and you can boil it hell! Therefore, I bought my second trampoline made of steel: much more maintainable!

That is, in principle, all the breakdowns. For clarity, I recorded a short video on this topic - I recommend watching:

By the way, at the end there was an interesting episode: the electrician Yuri came up and asked to make cotton wool. While I was making cotton wool for him (and this is the very end - in the video I am already without a uniform, in work clothes for loading), more clients came up and Masha and I finished off another 150 rubles to the total revenue. A trifle, but nice!Friends, let's not get lost on the Internet! I suggest that you receive email notifications about the publication of my new articles, so you will always receive all new articles. Subscribe now! Image - DIY repair of an inflatable trampoline on a seam

I know that time is money. Therefore, if you need a squeeze of useful information on a topic, and there is no time to read the entire site, I recommend purchasing a book "Sweet Business 3 - A Practitioner's Guide".
The book contains all the information on how to make money on cotton candy and outbound trade, doing it yourself or hiring people. Only experience and practice, no water. See reviews.

The material itself, more precisely, the PVC fabric - modern, durable and wearable materialbut even he cannot be 100% insured against cuts, punctures or other damage.

There is always a certain percentage of danger that the surface of the trampoline may lose its integrity. But there is nothing wrong with that, because together with the attraction in the set you have a rem. set, and in it everything is already in store for self-repair.

It will take you time no more than half an hour... But, of course, if you are afraid to do it yourself for the first time, then we will always help you with this!

Rem. set, special glue and a piece of PVC for applying patches must be attached to it;
Scissors;
Solvent, acetone (These solutions can be found at any hardware store that sells paints and varnishes);
Brush, small, but with rather thick bristles;
Elasticroller or rolling (this tool is a bit like a spatula, only the iron blade is much thicker);
Ball pen or a simple lead pencil;
Directly self spoiled trampoline.

When gluing, you cannot use SUPER glue, the best is the glue that goes into the repair. set.

But you can also use:

– Glue Moment for PVC (for PVC boats).

Regarding Desmokol, this is an analogue of Uranium, and in order to bring the solution to a better composition, you can add Desmodur additive in the ratio 5-7% to the whole volume.

use sandpaper for stripping the PVC layer, as this can only harm the integrity of the material;
overuse acetone or another solvent - they can also spoil the top layer (dissolve);
warm PVC with an open fire, the material may be damaged.

1. Prepare the area where the damage occurred. To do this, the material should be cleaned of contamination, then treated with a solvent and dried, but do not overdo it with the application of the substance.

The repair area must be firm and perfectly level.

2. Preparing the PVC patchintended for use as a patch.

The main thing is not to confuse the sides of the material: on the glossy (outer) side of the trampoline, a piece of PVC should be applied seamy side, that is, matte... These sides are very easy to distinguish from each other and you will not have any difficulties with this.

You can cut out the area to be glued by about, by eye or even before the glue is applied. attach a piece of PVC to the puncture and circle with a pencil or handle a zone, which will play the role of a patch.

3. Applying glue.

With an elastic brush, but a small layer of glue should be applied to the surface of the trampoline around the cut and to the PVC piece itself.

For better fixation both parts of the material can be dried a little with a hairdryer , but not much, so as not to heat the material (up to 70-80 degrees). To assess the condition of the layer, run your hand over both surfaces: if the glue does not stick and does not reach for your hand, you can proceed.

4. The gluing process.

The cut out patch, processed with glue, apply to the puncture and run over it with a hard roller or rolling ... We smooth out the glued part with our hands so that the air can escape completely, and the patch on the trampoline lies perfectly flat.

5. Time to commit.

On the repaired piece of material install the press (any heavy household item with a flat surface) and leave it to stick for 24 hours ... If the cut is small, about 2-5 cm from a puncture, then the trampoline can already be used in 2-3 hours .

Of course, if we talk about convenience or saving time, then self-repairing a trampoline more efficient than going to a specialist.

The whole event can be held close to the trampoline location or at your home, the structure does not have to be transported too far.

But in case of more serious damage, ruptures, it is better to seek help from a specialist.

If the situation happened just during the influx of people, during the seasonal period, when every hour counts, then it is more optimal to contact a specialist , which efficiently and in the shortest possible time will make a reliable repair of the structure.
By contacting a competent service, you get a guaranteed result and then do not doubt the quality of the event.
The repaired area will no longer create problems for you, you no longer have to waste time on its repeated repair if the first time self-repair is unsuccessful.

Of course, preventing a problem is always easier than dealing with it. Therefore, to avoid damage, simply adhere to the basic rules of maintenance and handling of the trampoline ... Strong and wear-resistant material is almost not afraid of burnout, and the minimum period of perfect use of the structure is 3 years.

What to do if an inflatable trampoline breaks? How to properly repair an inflatable trampoline? In this video, you will learn how to quickly repair a trampoline with your own hands.# trampoline repair # inflatable trampoline repair # inflatable trampolines # game modules # attractions #attro #attro # inflatable slides # inflatable water park # rappa # small business # business unit # earn # your business #inflatableslide #inflatablebouncer #inflatableVideo Repair of an inflatable trampoline. The trampoline broke. How to seal an inflatable trampoline of the ATTRO Business channelAn inflatable PVC mattress or an inflatable bed is a useful thing, both for outdoor recreation and as a spare sleeping place for guests, and sometimes for oneself. But besides convenience, there is a drawback in Intex or any other inflatable mattresses, they must be carefully handled in order to avoid punctures, cuts or tears, and this is true both for the velor top of the mattress and the base made of polyvinyl chloride. A puncture or rupture is sometimes noticed when you wake up prematurely from touching the floor of the room. Or if you unsuccessfully try to inflate the mattress tightly after storage. Such an unexpected event immediately causes confusion, what to do, how to repair, how to glue or how to fix an air mattress with your own hands? Where can I find the patch? What kind of glue to glue? You don't have to look for a workshop! You can glue the inflatable mattress with your own hands. Image - DIY repair of an inflatable trampoline on a seam

In the absence of patches, some inexpensive inflatable PVC toy for children can serve as material for replacing them. Cut out a patch in the shape of a circle from the toy. Sandpaper is purchased from a hardware store. Degreasing agent - alcohol or gasoline.

We are looking for a hole, hole, puncture, rupture or torn seam in the mattress. We need to be optimistic and patient. I offer the following simple instructions for finding a puncture and repairing an air mattress:

1. In a quiet room or room, inflate the mattress as tightly as possible.

2. We listen and try to localize the leakage area by the sound of the outgoing air.

3. Carefully study the area of the leak, for example, slowly moving your palm at a distance of 1-3 cm from the surface to localize the hole of the hole. A thin stream of air will "cool" the palm.

4. If the hole or holes are visible, mark them with a ballpoint pen or felt-tip pen.

5. Very small holes are sometimes difficult to see, then you will need to use soapy water, the place of bubbles is also marked.

6. In INTEX mattresses, the sore spot is the valve, therefore, the bleeding is not always the result of a puncture; the valve is also checked with soap and water. Attention! Do not check the valve of the built-in pump in this way or dry it thoroughly before switching on.

6. Prepare a patch of the required size, the edge of the patch should be no closer than 15 mm from the hole.

7. The place of repair is dried, cleaned with sandpaper, and the patch is also cleaned. You can try to clean the fleecy surface with a cotton swab dipped in acetone.

8. Put the patch on the place of gluing and trace its contours on the mattress, this will allow you to gently apply the glue.

9. Degrease the place of gluing and blow off the air from the mattress. For acceleration, you can rearrange the hose on the pump or use a vacuum cleaner.

10. Apply glue to the marked area on the mattress and to the patch.

11. After applying the "Crystal" glue, pause for 5-10 minutes and strongly squeeze the patch and the surface of the mattress. Of course, the surface of the mattress is not always even. Compression density during gluing can be ensured as follows: We try to lay the canvas in the place of gluing on a flat surface. Quickly without the formation of bubbles, roll the patch onto the gluing site, put a piece of polyethylene on the patch, then a piece of foam 3-5 mm thick, slightly larger than the size of the patch, and put a load on top. This sequence of actions is best done before gluing. After installing the load, it is necessary to forcefully press the gluing place for 5-15 seconds and leave the gluing alone for several hours.

12. If everything is glued well and there is no other damage, then we pump up the mattress in 24 hours and use it.

When using the mattress outdoors, inspect the mattress placement surface for piercing objects and cutting glass fragments. Do not pull the mattress on a hard surface with people lying on it; in this case, unacceptable stresses may occur on the seams and cells of the mattress with breaks in the fastening of the inner frame. Avoid playing with animals near the inflatable mattress, cats can easily break through the covering with their claws.

yes indeed the cats have untied a rubber three-section mattress with 18 holes to glue them I will not cut this section

From my:
1. You can quickly blow off the mattress with a vacuum cleaner
2. To deflate by jumping and running on the mattress is almost hopeless, but the chances of damaging the mattress are even higher, so just let the mattress deflate under its own weight, you can put a cotton mattress on top, for example, over the entire area, this will speed up the process a little.
3. For INTEX mattresses with a fleecy surface, it is optimal to remove the fluff before gluing with acetone, it is normally cleaned off with a cotton swab or disc, and only then work with such a surface.
4. In INTEX mattresses, the sore spot is the valve, therefore, the bleeding is not always the result of a puncture, the valve is also checked with soap and water, but do not check the valve of the built-in pump in this way or dry it thoroughly before turning it on.

Thanks for the detailed and helpful comment!

Thank you, I will try to glue it together today.

how to replace the patch if there is no spare pvc material for the mattress?

Strange, the answer is in the text “In the absence of patches, some cheap inflatable toy for children can serve as material for replacing them. Sandpaper is purchased from a hardware store. Degreasing agent - alcohol or gasoline. "

Hello . Thanks for this article. Need advice:
It is necessary to glue the anti-decubitus cellular mattress made of polyvinyl chloride (PVC). There are no problems in patches, there are plenty of them
What adhesives do you recommend?

-It is desirable that he glue it together as quickly as possible (in order to lay the bedridden patient on the glued mattress as soon as possible). In most adhesives, the term is stipulated for a day. This is VERY long in our case.
- so that the glue smell in a closed room (apartment) is not very long.

What is the minimum gluing time to use the product? (if it is important, the patient's weight is 55 kg, but on the other hand, the compressor constantly, every 6 minutes, alternately inflates / deflates the cells of the mattress)

What to do if an inflatable trampoline breaks? How to properly repair an inflatable trampoline? In this video, you are.

How to repair a trampoline, trampoline. If a small hole appears on the trampoline, trampoline. We are repairing a trampoline.

It is very easy to repair a trampoline. Follow our instructions and take care of your trampolines! Website: my.housecope.com/wp-content/uploads/ext/807 Tel.

In this video you will see one of the options for gluing a PVC product using a hairdryer. They hold on.

SuperBatut.rf Repair of nylon mesh in PVC. We keep up with the times, we use modern and relevant techno.

How to assemble a trampoline correctly: from the frame to the net. We discuss the springs - how to tighten them, how to use them correctly.

Sewing a hole - 10:00 Hemming trousers by hand - 00:00 How to hem trousers with a blind seam or sew up ripped karma.

as swimming pools are bursting.

HOW TO ASSEMBLE A TRAMPOLINE IN HOME CONDITIONS Having pretty much digged in the attic, I and my friends found our old trampoline.

What will happen if you JUMP INTO THE WATER FROM A HIGH ALTITUDE SUBSCRIBE TO NEW ISSUES ▻ If you like it.

Gymnastic trampolines. Trampoline mat made in the USA. It is made of heavy-duty and wear-resistant polypropylene.

124. Trampoline in your hands (Almost)

We glue the inflatable pool using sandpaper glue and a press. Quickly, cheaply and reliably. Since I myself have recently.

Website: https://my.housecope.com/wp-content/uploads/ext/807/shop/kommercheskijj-batut-belyjj-klyk Phone: 8 800 500 42 90.

a story about the most frequent breakdowns in the "holiday" business: breakdowns of a trampoline, trade tents. And chance.

Website: https://my.housecope.com/wp-content/uploads/ext/807/kak-khranit-batut Phone: 8 800 500 42 90 Storage of inflatable attractions is preservation for later.

How to install an inflatable trampoline

Technotent company performed trampoline repair. The video shows a control test.

7 stitches from being hit with a metal baton surreptitiously in the transition. We sew, discuss the battle)

Video from a factory for the production of inflatable trampolines. All stages of making high-quality trampolines for a large one.

How to sew a mosquito net on a stroller is a very simple way.

How to sew a hole is what you will see in this lesson, you will learn simple things.

A 5.5-year-old child is jumping on a trampoline arena with a net. The diameter of the arena is 135 cm, good and stable. Purchase.

Subscribe to my channel:

Assembling the i-JUMP trampoline In the video, the specialists assemble the 12 ft i-jump trampoline with a protective net and a ladder. Trampoline.

Everyone loves spectacular fights in the UFC, in Boxing, it doesn't matter if knockouts in 2018 or knockouts in 2017. It's always beautiful and spectacular. A.

Everyone knows how to glue a camera on a bicycle, but few people know how to glue a tire. In this release.

Floor beams trampoline effect, second light construction.

pool frame how to glue the simple way #PoolFrameHow to glue the simple way #Repair

Inflatable robot for commercial rental Who did not play pirate in childhood.

This video will give you the information you need to know how to RIGHTLY repair your cut.

An independent review was sent by our client about the results of the work of Liquid Patch as an adhesive for an inflatable mattress.

The inflatable trampoline is made of dense PVC fabric, but, alas, even such a strong and strong material is not insured against damage that may arise from careless handling.

Fortunately, it is quite possible to eliminate punctures, cuts and other violations of the integrity of the product at home, using improvised means.

If you want to know how to glue an inflatable trampoline, then stay with us.

Usually, the repair kit goes as a gift to the sports equipment, so all the manipulations will take a minimum of time. In addition, you should also prepare:

scissors;
acetone or other solvent;
a small brush with stiff bristles;
roller or roller;
pencil.

Important! Don't use superglue. There is already an adhesive in the repair kit, which is best suited for the material and is guaranteed to provide a good result.

How to glue an inflatable trampoline at home? To do this, you must adhere to a certain order of actions:

Before gluing the inflatable trampoline, clean the surface of the material from dirt. Treat the damaged area around the perimeter with acetone / solvent. Dry the product thoroughly.
Prepare the PVC patch that comes with the kit. It is important not to confuse the sides of the material and place it with the matte side towards the trampoline. Cut a piece to a suitable size and hold it over the damaged area to make sure it fits.
Using a resilient brush, apply a small layer of glue to the surface of the trampoline and the patch. For the best effect, you can warm up the fate a little with an ordinary household hair dryer.
Apply the patch to the damaged area and smooth. For these purposes, a roll-in or a hard roller is best suited.
Press the repaired area for about 24 hours.

You are probably interested in the question: how to glue an inflatable trampoline along the seam? It is better to entrust such serious damage to specialists and not try to do it yourself.

Important! All work must be carried out on a firm and level place (table, floor, etc.). Do not use sandpaper to clean the surface of the trampoline or seal, as this may cause new damage. Do not overdo it with solvent and hairdryer, everything should be in moderation.

You can see the full range of trampolines by following the link.

Urgent repair: inflatable slides, inflatable trampolines, inflatable pools, trampoline complexes, PVC water attractions, inflatable boats, bananas, mattresses, etc.

We repair any product made of PVC fabric from a trampoline to awning hangars!

What to do if a trampoline breaks and repairs are needed?

The fastest way is to call the phone and get all the answers: +38 (050) 419-8-333
We will quickly and efficiently repair inflatable attractions of any complexity:

Repair of an inflatable trampoline
Repair of an inflatable pool or PVC cover
Repair of a park attraction
repair of inflatable boats or kayaks
Repair of pneumatic robot
Water slide repair
Trampoline set repair

The repair includes: seams stitching, hermetic sealing, gluing patches, if necessary - complete replacement of worn-out parts and elements. We also take on repair of trampolines made in China.

The cost depends on many factors: what condition the product is in, whether large fragments need to be replaced or small patches can be dispensed with, how many cracks, cuts and tears on the surface, how difficult it is to get to them, and so on. Therefore, our specialists will be able to most accurately determine the cost of repair after visual assessment of damage.

To do this, we ask clients to either send a photo of the trampoline in an inflated form, which clearly shows the nature and extent of the damage, or send us the attraction itself. Then we will draw up a detailed estimate of the repair work.

Small cuts or punctures can be corrected on the spot, for this our specialist can go to you with special equipment and make repairs as soon as possible, using high-quality materials. If the damage is extensive, their correction will take a lot of time - the repair must be carried out directly at our production site.

There are several main reasons why the attraction you bought disappointed you and fell into disrepair.

Warranty and post-warranty repair of a trampoline

HWhat is covered by the warranty? We guarantee that, subject to the operating conditions specified in the instructions, during the warranty period, the seams will not disperse, and the fabric will not tear. Cuts, including sharp parts of clothing, punctures, burn marks and similar damage are not covered by the warranty.

Don't wait a few months! With us you will have time to repair the trampoline by the beginning of the season!
Still have questions? Call by phone: +38 (050) 419-8-333

See ready-made new offers for inflatable attractions:

Option number 1. Happy hop trampoline: For punctures and cuts in the PVC laminated surfaces of the trampoline (everything that is pumped with air), use the repair kit that comes with the trampoline. Repair Patch is used in case of punctures and small cuts.

It is necessary to cut a patch of the desired size without sharp corners, stick it on the damaged, cleaned area and do not inflate the happy hop trampoline for 20 minutes, for larger damage, use scraps of cloth and glue.

Does it let air pass at the seam joint? It is banal to sew up with a thread.

Seal the hole in the inflatable mattress, trampoline, ball, bed:

When buying inflatable products (mattress, trampoline, toys and circles), it is advisable to take care of PVC repair kits. We have them on sale:
The kit includes the most necessary things:
1 PVC adhesive. A similar one is sold in auto parts for repairing truck awnings.
2 A piece of PVC for the patch.

To find the puncture site it is enough to take a washcloth, use soap to make foam and wipe the punctured product, after which it is necessary to degrease the place of gluing. Then you need to cut off the patch of the required size, apply glue and stick the patch. You need to combine the patch without stopping - the glue softens the PVC to a soft and plastic state, and dries quickly.

And a folk recipe for a hole in the seam of PVC productswhen the patch cannot be applied:
take a regular napkin and glue, drip glue (superglue) onto the hole near the seam and apply the napkin, it dries up tightly.

Back to the list of inflatable trampolines Large and small trampolines for the house

These are recommendations on how to quickly restore the tightness of an inflatable product without causing additional harm to it. You should not expect too much from a temporary repair, moreover, it will need to be redone in a workshop, but often this is the only opportunity.

Do not use super glue!

Repair of circles, vests and small pools.

How to find the air exit points?

inspect visually,
try with the back of your hand to hear a cold stream of air,
partially immerse in a container of water and turn, bubbles indicate a leak.

it is necessary to mark the places of damage, blow off, remove dirt, dry.

For self-repair, the easiest way is to use the Intex repair kit (59632)

There is little damage on a flat area.

Cut a patch with a diameter of 2 cm from the material of the repair kit. It is better to wipe the patch and the damaged area with alcohol, at least wipe it with a clean, dry cloth. The gluing area must be dry. Apply glue from a tube to the patch and spread it with a “greasy” layer. Immediately apply the patch with glue to the damaged area, smooth and press the patch until the glue dries. The glue should dry in 1-2 minutes. After 30 minutes, you can use it. If you use Dismakol as a glue, then the glue is applied in a thin layer, it is dried for 10 minutes, then the second layer is applied, it is dried to the state of "scotch tape", it remains to glue and smooth it. You can very gently warm up with a hair dryer, carefully, the material of circles and pools can easily melt.

There is little damage at the seam edge.

Inflate about halfway to see where the leak is. Fill this place with glue from a tube, let it dry, pour more until the bubbles disappear. After 2 hours, you can use it. It doesn't always work out.

There is damage more than 1 cm. - contact the workshop for the repair of inflatable products.

R Repair of inflatable mattresses, beds, sofas, Intex boats.

There are many tips on how to find punctures in air mattresses and beds on your own. I do not recommend pouring water into an inflatable mattress, let alone an inflatable bed. The method is, of course, effective for finding holes. But after that it is very difficult to dry an air mattress, and an air bed is impossible. White streaks will appear on the surface and the fabric will be damp. Sleeping on such an inflatable mattress will be very unpleasant.

To find air leaks, you need to:

visually inspect for scratches, scoring, etc.
try to hear the cold air flow with the back of your hand
Take a container for water and a sponge. Make a soapy solution and lather the inflated mattress from all sides, mark the places where air bubbles exit, dry and deflate the mattress.

There are small punctures or micro tears in the seams.

Temporary repairs are done as follows. This requires polyurethane glue, PVC material or leather. Cut out a patch with a diameter of 2 cm. The patch and the damaged area must be cleaned and dried without peeling off the lint from the surface of the air mattress. It will be correct, of course, to remove the lint, but there is a possibility of causing additional damage. Then the patch and the place of damage must be coated with a layer of glue and allowed to dry. This is 10-15 minutes. Spread a thin layer again, dry, but not completely. The glue should remain sticky. Press the patch to the seam and hold, smoothing the edges. No need to heat with lighters, matches, a mug of hot water, etc. It could be worse. You can only heat with a hairdryer and then carefully. Wait at least an hour. Inflate and expect results. It is unlikely that it will be possible to completely eliminate the leak at the rupture site, but the punctures must be repaired.

If the mattress is still deflating, repeat the entire procedure, starting with looking for damage, and so on until the mattress stops deflating.

There are large gaps on the flat surface.

Lit is better to go straight to the workshop, but if it is not possible, glue in the same way as a puncture, but the patch should protrude 1 cm in all directions from the gap. In the workshop, I glue on both sides with a special adhesive.

There is a gap in the seam along the edge of the seam larger than 5 mm.

Contact the workshop. Self-repair of breaks is more difficult and often does not lead to the desired result. And repair in a workshop "after repair" is usually more complicated and expensive.

The valve is often thought to be causing the mattress to deflate. It's easy to check. This requires a soapy solution and a brush. Inflate the mattress, close the valve cap. Then you need to completely lather the valve from all sides with thick foam. If no air bubbles are observed, then the valve has nothing to do with it. If there are bubbles, go to the workshop or look for a valve. An attempt to smooth the plane of the valve surface with emery paper will not give any tangible result.

If you do not want to soap, dry, and so on yourself, contact a specialist.

Watch the video course Air Mattress Repair School.