2) Using a plastic tool, pry off the back panel, the latches shown in the figure below should come loose
11) Disconnect the two latches to remove the motherboard and display. One latch on the left side
15) Disconnect the ribbon cable with a plastic tool. Be careful not to damage the items nearby on the motherboard
24) If the keyboard works, then this is optional. Removing the keyboard backing
This is a translation of the official Nokia C5-00 disassembly guide from Nokia.
VIDEO
Today we are going to talk about how to change the display on your phone. Nokia С5-00 .
As usual, first remove the back cover and take out the battery, SIM card, memory card. Then, using a spatula, remove the camera panel.
Under the cover, there are two screws in the holes.
Then again use the spatula to remove the front panel.
Next, you will need to unscrew the screws in the places indicated in the next photo.
After that, we take a spatula and proceed to removing the motherboard.
The next photo shows the motherboard and middle panel after separation.
We put the middle panel aside and take the motherboard.
Use a spatula to detach.
Then we remove the speaker module.
Now you can remove the frame that holds the display. Fold back the frame as shown in the next photo.
So we got to the display.
We remove the broken display, put a new one in its place and check its performance.
If the display is working properly, you can fold the ribbon cable. We use the old one as a sample display .
Install display , remove the protective film and assemble the device in the reverse order.
- install a module with speakers,
- connect the keyboard board loop,
- install the board in the middle,
- install the front panel,
good time of day, can someone tell me drowned c5 now does not see either the network or the memory card, can it be fixed, can the firmware help you in advance thanks
This site has an article on drowned people and the steps to take. Look in the "Helpful Tips" section or at the following link:
We make the firmware according to the following rule:
and on nokia x2-00 you can also
hello))) please tell me, I have a nokia c5-00. I would like to put a password on it, when the phone is unlocked - immediately so that the password is requested. I press options-general-protection-phone and sim-card-lock code. then I enter the standard lock code 12345. then I come up with a new one, for example, I enter 445566554 and confirm it again. and writes that the code is incorrect. tell me then what code can I enter? or am I doing something wrong?) Thanks in advance!
It looks like you have already changed the standard code 12345 to something else. Therefore, when you enter it, the phone gives an error.
Hello) I have this question) I managed to change the security code, I entered mine, but when I turn on the lock and then click “unlock”, there is no password request. How can this be fixed so that when unlocking it is there? Thanks in advance))
Olya, have you read the instructions for your phone? There are answers to all your questions.
Hello! After installing the display, the screen flashes constantly, as if updating, what could it be? Thank you.
Perhaps they did not install a high-quality display, or something was damaged during installation.
They brought a phone for repair, and a fairly new one, the store refused to send it to the service, as well as to exchange it, explaining that the phone was flooded with water and therefore it does not have any sound at all or the microphone works! Well, what are we going to do, we need to help the person. The phone itself turns on and works, but with its main function - to call and conduct conversations, my grandmother has a problem. The phone itself is quite interesting, the display is not small, there is a flashlight, 2 SIM cards, and a slot for a USB flash drive.
Everything is unscrewed simply and classically, although Nokia changed the owner, but the assembly technology is still the same modular - we unscrew 4 screws with a special screwdriver, remove part of the panel case, hook 4 latches, take out the board and see that the phone was in fact in contact with water - the connector is all green from oxidation.
I, as a rule, do not strongly scrape such damage with screwdrivers and sandpaper, in order to preserve the device I apply the degreaser with a cotton swab, rub, and heat it up with a hair dryer to 100 degrees - as a result, the surface is like new, and the contact will be wonderful.
In addition to problems with sound, there was a problem with the network - here I had to clean the dimes at the antenna, which was a plate with leads connected in the same way as the headphone jack with the board.
We collect it by drying it with air from a hair dryer, check it - everything works, there is sound, the network catches great, the radio works too. In addition, we wipe everything with a napkin and the phone is like new, both grandmother and I are happy))
Is your Nokia S5 cell phone not working? Such news, no doubt, will upset any user. Our telemama service center will carry out a professional repair Nokia C5 of any complexity.
First of all, we do diagnostics. A time-consuming service and completely free. You can easily purchase any original part from us, and at the lowest cost in Moscow.
There is no doubt that the phones of this brand are considered very reliable and of high quality. But, like any other technique, they can be broken.Most often, users break screens, pull out the connector, or face the loss of sound or images on the phone. Whatever you have to face, whatever situation you have to face, we will repair Nokia C5 of any complexity.
If the damage is not serious, then we can fix the mobile in your presence in just a few minutes. Our main advantage is that we repair Nokia C5 cell phones using original parts. We only cooperate with manufacturers, so it is unlikely that at least someone will make the cost lower than ours.
Our experienced craftsmen have been repairing mobile phones for a long time, so there are no hopeless situations for them.
Most often, they contact us at the Telemam service center with a request to fix the mobile after it fell or was broken. It is mechanical damage that is most often the reason why it is necessary repair Nokia S5-00 ... This is why you should always be careful with your technique.
After we repair Nokia S5-00, customers receive a long-term phone warranty. That is why you can be confident and confident that your cell phone will not fail anytime soon.
Until the end of the promotion there are
Display + glass for:
I haven't described repairs for a long time, a rather large influx of work, but today I decided to fix the situation. I got a phone for repair Nokia C5-03 with a missing image. Local craftsmen tried to change the display, but this did not bring the desired result.
I started the test with the Self Test operation using the BEST programmer, as a result of which I received one error related to a broken display bus:
Since I did not find a diagram for this phone, everything that is on the Internet on this topic is just a collection of files with pieces of diagrams of different Nokia phones. After reading several topics on thematic forums and carefully examining the board, I found a small analogy in the inclusion of the display with the Nokia 5228 (and others). A distinctive feature of the display connection of Nokia C5-03 from Nokia 5228 is that another channel In5 (C1) - Out5 (C4) is activated on the Z2450 antistatic filter (the reference designations will be used as in Nokia 5228).
For greater clarity and further convenient use, I sketched the diagram of switching on the Nokia C5-03 display.
Armed with a multimeter in diode dialing mode, I checked the display connector for an open circuit, the LoSSI Reset signal at the 16th pin of the X2470 connector turned out to be disconnected. Then I started looking for an antistatic filter and ran my eyes over the board and found it near the camera. Just near it, I found some oxides, on the test site, which was the LoSSI Reset signal.
Externally, the contact pad was intact, I did not pay enough attention to it. I removed the filter and rang the output to which the reset signal came.
Having walked a little along the control point with a scalpel, I realized that only copper dust remained from the copper and, having removed a small part of the mask and the top layer of the board, I got to the remaining bits of the inner layer tracks.
This is how the final part of the image restoration work looks like, the antistatic filter did not reinstall and replaced it with wires.
Is your Nokia S5 cell phone not working? Such news, no doubt, will upset any user. Our telemama service center will carry out a professional repair Nokia C5 of any complexity.
First of all, we do diagnostics. A time-consuming service and completely free. You can easily purchase any original part from us, and at the lowest cost in Moscow.
There is no doubt that the phones of this brand are considered very reliable and of high quality. But, like any other technique, they can be broken. Most often, users break screens, pull out the connector, or face the loss of sound or images on the phone. Whatever you have to face, whatever situation you have to face, we will repair Nokia C5 of any complexity.
If the damage is not serious, then we can fix the mobile in your presence in just a few minutes. Our main advantage is that we repair Nokia C5 cell phones using original parts. We only cooperate with manufacturers, so it is unlikely that at least someone will make the cost lower than ours.
Our experienced craftsmen have been repairing mobile phones for a long time, so there are no hopeless situations for them.
Most often, they contact us at the Telemam service center with a request to fix the mobile after it fell or was broken. It is mechanical damage that is most often the reason why it is necessary repair Nokia S5-00 ... This is why you should always be careful with your technique.
After we repair Nokia S5-00, customers receive a long-term phone warranty. That is why you can be confident and confident that your cell phone will not fail anytime soon.
Until the end of the promotion there are
Display + glass for:
Nokia phones are one of the most reliable, and often even the owners of modern smartphones do not want to part with their "old friend", using it as a backup option. And some simply do not want to change Nokia to a more modern phone, since they are completely satisfied with it.
But even with these gadgets, troubles happen. For example, the nokia asha 200 phone is a great usable model, but it happens to freeze. The cause may be shock, water ingress, memory overload, operating system failure.
It happens that there is no way to get into the phone repair service. Something you can do yourself. For example, clear memory by deleting unnecessary SMS and contacts. If your phone gets wet, try drying it by removing the back cover and removing the battery. It will take 1-2 days. If the phone does not work after that, it means that the contacts have oxidized. Try cleaning them with rubbing alcohol, acetone, or a special oxide remover. If this did not help, then alas ... This means that the liquid has thoroughly spoiled the microcircuits and you cannot do without replacing them. And it is better to do it in the service.
If you still want to try self-soldering microcircuits, wiring or a pad on the board, you will need a hair dryer to warm up the microcircuits, flux and rosin. You can only warm up those that are not filled with a compound - a special resin. But if you really need to, there are liquids for removing the compound. Now we act according to the following algorithm:
we warm up and remove the microcircuit;
we clean the remnants of the legs on the microcircuit and the board with a soldering iron;
we put the microcircuit on the stencil, making sure that the holes of the stencil coincide with the contacts of the microcircuit;
cover the holes with BGA paste;
heat the paste until the lead balls appear;
wait for cooling, then remove the stencil;
heat the microcircuit to the board with a hairdryer.
Replacing the glass is easy. It must be greased with soldering fat and heated with a hairdryer. Then clean the contacts on the board to zero with a soldering iron. After that, put a new glass and warm it up with a hairdryer.
Nokia software repair is a job for specialists. It is necessary to understand the firmware configuration: which files are responsible for which functions, as well as many other nuances.It is better for a beginner not to take on this and take the phone to the service, but such trifles as a crack in the glass are an excuse to train their skills.
Using the key tool, open the SIM card slot and take it out.
Do not press too hard, it may cause breakage.
Disconnect the display module.
Using a screwdriver (Phillips 1.5 mm), unscrew 1 bolt and remove the bar that secures the module and battery connectors.
Disconnect the battery connector.
Disconnect the connector and remove the display module.
Using a screwdriver (Phillips 1.5 mm), unscrew 17 bolts around the perimeter of the phone.
Disconnect the middle panel and battery.
We take out the speaker from the fixing hole in the middle panel.
Using a screwdriver (Phillips 1.5 mm), unscrew the 3 bolts on the bottom board.
Using a screwdriver (Phillips 1.5 mm), unscrew the 3 bolts and remove the protection of the connectors.
Disconnect the coaxial cable connector on the lower PCB and the board-to-board cable connector and remove the board.
The board-to-board ribbon connector is located on the inside of the PCB, so be careful when removing it.
Disconnect the board-to-board cable.
Disconnect the lower unit with the speaker.
We turn the board over, disconnect the coaxial cable connector from the inside and remove the board.
We take out the flash from the fixing hole in the module frame.
VIDEO
Hello everyone! Nako with you! And in this article I will tell you how to disassemble the legendary Nokia C5-06 phone. I will disassemble my personal phone, which served me faithfully.
1.Prepare your workplace
2. Before disassembling, remove static from your hands by grasping something iron with both hands.
3. The details are very thin and brittle, so be extreme, accurate, do everything slowly.
4. You must be in a great mood.
2. Remove the battery, SIM card, USB flash drive
3.Use the spatula to pry the front part and remove it, it is held by two latches
4. Remove the SIM card and unscrew the four screws
5. Insert the spatula into the gap and drag it over the entire body of the phone, counterclockwise, thereby opening the body of the phone. After that, carefully take and turn the phone over, then raise the touchscreen
6.Disconnect the touchscreen cable, unfortunately I don't have it
7. With tweezers we pry on the brown frame and lift it to the top, after that we turn off the matrix cable
8. Use tweezers to pry the board.
9. Putting it all in the reverse order.
This concludes the article on how to disassemble the Nokia C5 06 to replace the display or housing.
It will be interesting for you with me!
Subscribe to the blog and receive free articles by mail!
In block diagnostics, it is determined which specific element (housing, protective glass, sensor, printed circuit board, connectors, speakers, microphone, antenna, battery) is out of order.
Checking s ayadku , if the phone is fully charged, otherwise:
We check the phone connector, if it works, then:
If all of the above does not suit you, then you will need to reflash or repair the phone's motherboard.
Checking P I will lose the charge if the phone battery is charged then:
We check and whether it is correct power button on the phone;
If nothing was found at this stage, the cause of the breakdown, we recall - if the phone was flooded with liquid, or the phone fell and stopped turning on, most likely the phone's motherboard will need to be repaired.
Check if the phone detects another sim card if it detects then:
Checking Phone settings if the settings are correct then:
Phone flashing is required.
Checking phone flash card if serviceable then:
Checking USB flash drive connector on the phone, if it is also working properly, then:
You need to flash your phone, or remot the phone's motherboard.
Checking usb cable if the cable is ok then:
We check the phone connector, if it is ok then:
You need a motherboard repair or phone flashing.
Checking settings , if the settings are correct, then:
Checking Internet connection , if the connection is stable, then you need to reflash your phone.
Checking Phone settings if the settings are correct then:
Checking WiFi adapter phone, if the order requires a flashing of the phone.
Checking connection cable to the computer if the cable is whole then:
Checking driver phone on the computer, if the correct drivers are installed, then:
Phone flashing is required.
Checking for availability physical damage screen, if not then:
Checking display cable phone, if the loop is intact, then:
Phone flashing or motherboard repair is required.
We check the integrity of the touch screen for damage, if it is intact then:
Checking touch screen flex , if int, then:
Phone flashing is required, or controller repair display.
Checking Phone settings if the settings are correct then:
We check the integrity of the microphone, if it is intact:
Check if it works microphone controller if it works on the phone:
Phone flashing is required.
Every day we listen to music on the phone, connect the charger, connect the phone to the computer, and naturally these connectors are subject to constant wear and tear, which subsequently leads to breakdowns of the Nokia C5-03 connectors.
Broken usb connector on Nokia C5-03:
When the USB cable is connected, the computer does not detect Nokia C5-03, or the connected device is not detected, or external signs of breakage are visible - the connector core is broken, the outer part of the connector is broken. Also, when connecting another cable, the same problems arise.
Broken charger connector on Nokia C5-03:
Nokia C5-03 does not charge when the charger is connected, the connector is broken. You can also determine that the connector is defective by connecting another charger. If the charging connector is outwardly working, but the phone does not charge, then the phone's motherboard will probably need to be repaired.
Broken audio jack on Nokia C5-03:
There is no sound when connecting headphones, or external breakdowns are visible. Also, the problem may be in the phone's settings, or in the firmware.
Repairing any Nokia C5-03 connector means removing the broken connector from the motherboard and replacing it with a similar new connector.
Do not postpone repairing the Nokia C5-03 connector until the connector is completely out of order. its use in a semi-working condition can damage the elements located near the connector, and as a result, it may be necessary to restore the board, replace adjacent elements.
Every year, phones perform more and more functions, and are already mini-computers. And for stable operation, a debugged operating system is required.
Phone flashing can be required for most problems - from the fact that the phone stopped detecting the computer to the phone display stopped working.
Microphone is not working on Nokia C5-03;The sensor stopped working on the Nokia C5-03 phone:
Nokia C5-03 turns on but there is no image on the screen or it is garbled by the phone:
Nokia C5-03 cannot see the computer;
Nokia C5-03 does not connect to Wifi;
Nokia C5-03 is not updated;
Nokia C5-03 will not turn on or does not load;
The Nokia C5-03 phone does not pick up the network, or does not see the sim card ;
Nokia C5-03 does not see SD card, does not detect a USB flash drive;
Nokia C5-03 not charging via usb.
Video (click to play).
Most of the Nokia C5-03 phone problems are caused by the firmware or an incorrect update. Due to a failure in the phone's firmware, the settings get lost, or the drivers of some controllers fail, and some functions may simply stop working.
