DIY nokia 206 repair

In block diagnostics, it is determined which specific element (housing, protective glass, sensor, printed circuit board, connectors, speakers, microphone, antenna, battery) is out of order.

• Checking sayadku, if the phone is fully charged, otherwise:
• We check the phone connector, if it works, then:
• If all of the above does not suit you, then you will need to reflash or repair the phone's motherboard.

• Checking PI will lose the chargeif the phone battery is charged then:
• We check and whether it is correct power button on the phone;
• If nothing was found at this stage, the cause of the breakdown, we recall - if the phone was flooded with liquid, or the phone fell and stopped turning on, most likely the phone's motherboard will need to be repaired.

• Check if the phone detects another sim cardif it detects then:
• Checking Phone settingsif the settings are correct then:
• Phone flashing is required.

• Checking phone flash cardif serviceable then:
• Checking USB flash drive connector on the phone, if it is also working properly, then:
• You need to flash your phone, or remot the phone's motherboard.

• Checking usb cableif the cable is ok then:
• We check the phone connector, if it is ok then:
• You need a motherboard repair or phone flashing.

• Checking settings, if the settings are correct, then:
• Checking Internet connection, if the connection is stable, then you need to reflash your phone.

• Checking Phone settingsif the settings are correct then:
• Checking WiFi adapter phone, if the order requires a flashing of the phone.

• Checking connection cable to the computer if the cable is whole then:
• Checking driver phone on the computer, if the correct drivers are installed, then:
• Phone flashing is required.

• Checking for availability physical damage screen, if not then:
• Checking display cable phone, if the loop is intact, then:
• Phone flashing or motherboard repair is required.

• We check the integrity of the touch screen for damage, if it is intact then:
• Checking touch screen flex, if int, then:
• Phone flashing is required, or controller repair display.

• Checking Phone settingsif the settings are correct then:
• We check the integrity of the microphone, if it is intact:
• Check if it works microphone controller if it works on the phone:
• Phone flashing is required.

In modern models of smartphones, there are practically no buttons left, and the keyboard function has been taken over touch glass... If the glass has lost its sensitivity, then you will not be able to fully control your smartphone.

And even if the touchpad on the Nokia 206 is cracked, but did not lose sensitivity, then you should know: he did not have long before the final breakdowns... If you don't want to lose the main control, or damage the display.

The display of the Nokia 206 mobile phone protects against damage by a special protective glass... If glass cracks or a chip appears on it as a result of the fall, then display your phone is at risk: it may be damaged too, and the image may become “blurred” or the phone 206 may stop displaying altogether. If dust or small debris gets behind the glass, which will further damage it. The specialists of our service center can replace the protective glass of your Nokia 206 phoneto prevent possible display breakage.

Component Nokia 206 phone diagnostics are diagnostics of the phone's system board. This type diagnostics, being more complex, is the identification of the damaged element on the board of the Nokia 206 phone. Repair after this diagnosis, the device is a re-soldering of microcircuits and replacement of defective elements on the board of the Nokia 206 phone.

Display - part screenwhich shows the image and is behind touch or protective glass. Damaged display phone Nokia 206, be it defective pixels or blurry screen, makes it difficult to work with the Nokia 206 phone or makes it impossible, because the image loses sharpness and clarity.

With a defective display, it is more difficult to read text on the Nokia 206 phone screen, operate with the touchscreen, and view images or videos.

Damaged display will not "cure" over time, but it can finally go out at the most inopportune moment, which can cause very great inconvenience. If the display on the Nokia 206 is faulty - You can contact our service center.

To replace the Nokia Nokia 206 housing, you need to contact a service center.

The online store strongly does not recommend making a replacement yourself. Also, we do not accept any responsibility for damage to individual parts of the phone, caused by the user or employees of service centers.

The information below is a short and incomplete description of the parsing of the Nokia Nokia 206 mobile phone.

All actions regarding the repair of the phone are carried out at their own peril and risk by the contractor.

1) Stick surface A with a protective film.

2) Free surface B using the notch on the bottom of the housing.

3) Remove surface B.

4) To remove surface A, use a tool to release the clips from the bottom of the housing.

5) Next, release the clips on the right side of the case by dragging the tool along this side.

6) Next, release the clips on the left side of the case by dragging the tool along this side.

7) Next, release the upper part of the case.

8) Remove surface A.

10) Stick the protective film on the display.

11) Remove the six Torx + size 6 screws in the order shown.

12) To remove the board, use the tool to release the three indicated clips.

13) Lift and remove the board.

14) Open the display connector with a tool. Be careful not to damage the connector and nearby components.

15) To remove the UI screen, release the two clips on the indicated side.

16) Also release the two clips on the other side.

17) Lift up and remove the UI screen.

19) Place the camera eject tool on top of the camera and press until the clips holding the camera release. Click on the tool button ...

21) Loosen one corner of the keyboard backing with a dental tool. Use tweezers to peel off the keyboard backing. Don't use it again.

22) Release the AV socket with the AV plug and pull it out with tweezers.

23) Release the DC jack with the AV plug and pull it out with tweezers.

24) Use a dental instrument to release the speaker.

25) Remove the speaker with tweezers. Don't use it again.

26) If any sticky speaker tape remains on surface D, peel it off.

27) Loosen the 3-in-1 speaker with a dental instrument and remove it with tweezers.

28) Peel off the gasket on the speaker. Don't use it again.

29) To remove the antenna module, use a tool and push down on the indicated clips.

30) Next, release the antenna module from the side and top.

It reacts to the power button starting from 4V, turns on even without using Bsi, while it does not complain about a low battery charge, but when used. BSI is complaining.

———- The message was added on 04/28/2014 at 11:31 am ———- The previous message was from 04/25/2014 at 17:56 ———-

[QUOTE = Vyacheslav72; 1037016] And my phone will start to turn on, show Nokia and go out. I connect the charger, it shows the charge, but if you try to turn it on, then for a moment the white screen goes out. After 30 sec. shows charge again. I connected it via USB, but the PC does not see it.What is the reason, tell me.

I also had a case. the firmware helped in the dead mode (Phoenix)

You can deliver the product yourself to our service center or use our logistics service

Upon acceptance, an acceptance certificate is drawn up and express diagnostics are done.

A full cycle of diagnostics and repair of a mobile phone (tablet) takes from 1 to 3 days.

During the repair, the master constantly informs the client about the readiness of the product and agrees on the cost.

The master consultant will check with you the operability of the phone (tablet) and only after that the payment is made

A simple and unpretentious phone, a device for those who do not need unnecessary bells and whistles. At the same time, the equipment includes a slot for memory cards up to 32 GB and a camera (the simplest of 1.3 megapixels), it is possible to use the device as a media player or FM receiver. Quite large for its class 2.4 ″ display has a resolution of 320x240 and supports 65 thousand colors. Due to its simplicity, the device has good autonomy - 20 hours of talk time and more than 47 days of standby time.

Our center professionally makes repair of mobile smartphones Nokia 206 and offers its customers not only a highly qualified approach, but also more than affordable prices for repair Nokia 206.

Good Nokia 206 cell phone diagnostics - the first stage of repair. Before giving the phone to our center, it is advisable that the owner of the phone describe in detail the nature of the breakdown, as well as tell about the factors that could lead to breakdown (for example, falling the phone to the floor).

Taking into account the data received by the customer, our technicians will make an accurate diagnosis of the device, establish the cause of the breakdown and eliminate it.

Malfunctions with the Nokia 206 software are fixed without diagnostics. Therefore, as flashing the phone will not harm the design, you can try to reanimate the device yourself. It is important to remember that the loss of files in the internal memory of the gadget with its firmware is almost 100%.

In the event of a problem with the software, the phone will most likely display this problem in this way:

• Will stop turning on (while connecting the smartphone to the computer using a USB cable, it appears in the device manager).
• It will reboot, turn on and off at its discretion.
• Will refuse any module, addition (camera, Blutooth, Wi-Fi, other)
• Reveals lethargy in work and so on.

In any case, flashing the device is the most budgetary and simplest repair of your product.

The flashing process for Nokia 206 is as follows:

1. Preparation of the system itself (as a rule, it is downloaded from the official website. This is a file with the .IMG extension).
2. A selection of the original USB cable, or the most suitable for such a procedure.
3. Installing a software update program (Flashtool, Batchtool or any other program) on your computer.
4. Connecting equipment that needs to be flashed to the computer using a USB cable, and the firmware process itself by clicking upgrade.

If the software was not installed, an error appeared, or the phone could not be started after flashing - the reason may be a malfunction in the hardware of the product or incorrect installation of the software. It is important to understand that an unsuccessful firmware will cause the phone to malfunction. Incorrectly stitched phones are called "bricks". It is quite difficult to restore the "brick" of the newest versions, while the old versions can be cured by yourself by starting the firmware over again.

There is one more way of flashing - through the system menu of the product. Such an attitude is much more complicated, requires knowledge and skills, and is not suitable for a beginner. In this case, the equipment must be returned to the BESTKOM service center.

Sensor (touchpad) and display malfunctions are very closely related to each other. Since usually, after breaking the touchpad, the sensor also becomes unusable. If, by “spraying the web”, the sensor can still work (possibly with errors and failures), then the display will end its functioning.

Separately, these elements cannot be restored.That is, it is not possible or advisable to repair a broken sensor or display. Most often, these malfunctions are solved by replacing broken parts with new ones.

If the main element of each product - the processor - becomes unusable, then an end is put to the performance of the smartphone. Most likely, such a malfunction will not be repaired.

Despite the fact that absolutely any board can be repaired by replacing a burned-out element, or by restoring a break in communication on the board, modern craftsmen do not undertake this responsible and painstaking work. After all, it is much easier and more profitable to install a new board than to restore an old one. In addition, when buying a new board for the client's device, the craftsmen keep the old parts for themselves. No wonder they can be re-soldered and put back into operation for another client.

It is in connection with the above that it is worth contacting only the BESTKOM service center. After all, an unscrupulous employee of a private workshop can easily deceive the owner of the phone by making poor-quality repairs, thereby aggravating the situation of an already "sick" device.

For a test run of BSI, you can short-circuit to ground, without this the body will not turn on .. Describe the dynamics of consumption, after pressing on?

For a test run of BSI, you can short-circuit to ground, without this the body will not turn on .. Describe the dynamics of consumption, after pressing on?

For a test run of BSI, you can short-circuit to ground, without this the body will not turn on .. Describe the dynamics of consumption, after pressing on?

What's this? I meant this: Connect to the LBP, with BSI shorted to ground, press the on button. and describe how the ammeter behaves

What's this? I meant this: Connect to the LBP, with BSI shorted to ground, press the on button. and describe how the ammeter behaves

You do not have access to view attachments:
1. Please log in or register.
2. You must have 15 (FIFTEEN) or more messages.
3. You can buy access to files from us.

But it may turn out that after such lengthy water procedures it will not start at all. ([/ quote]

It can turn on, it can only vibrate and that's it. It always turns on only after juggling the battery and with charging in the network. There is a backlight, the display is normal. It just doesn't work for a long time. Hangs up, and then turns off altogether. And further. if you put it on charge from the off state, then from the charging battery, it continues to “animate” even when the charger is disconnected from the network ..

He does not understand the witnesses that he was turned off. I remembered something, and such a picture emerges. 1) Always when it was turned off on the battery it was 3.62V, 2) It does not charge, 3) It does not indicate a low battery charge, but just stupidly turns off, 4) Does not understand that the body is disconnected from the charger.
One more. If you turn it on with a fully charged battery, nothing changes anyway

The body is "watery". roll the D3100
replace R3005 and check all items from BSI to D3100 (including R2081 R2080)

Was it a sewing cable? Did you turn on from him? Post test logs

Under the keyboard, clean
unsolder the display and USB connectors clean under and in them

Find the "firmware cable" with meals
There is a local, charging is in progress - it means BSI is alive. slowly we find out that you have a software problem.
Let's check one more hard? Remove the headset (headphones) plug - see if it turns on or not
clean, solder in place

after soldering are the nickels normal? not torn off?

Besides UFS, is there ATF, Best?
What is the current dynamics?

and try with another battery (and put this in another phone, it will work)))

I connected the charging and showed the charging indicator. but when the charger is turned off, it also continues (allegedly) to charge replaced V2204, V2205, R2209, R2210, R2211, R2212, R2213, R2214, capacities C2217, C2218, C2219, C2220 are also replaced. There are no options. here is the log

Earnings at home

Where in Ulyanovsk to buy a remedy, a drink for alcoholism (Alco Barrier)? Order, composition, instructions for use.
Drops "Alco Barrier" are an effective antidote that rapidly removes toxic substances from the patient's organs and immediately eliminates the craving for.
Dec 18, 2017 - Alco Barrier - a remedy for alcoholism, price 4 950 Tg., Buy in Almaty -. Detailed information .
Powder "AlcoBarrier" is the most efficient antidote that removes toxic toxins from the patient's organs and effectively expels weakness for.
Alcohol barrier is an effective remedy for alcoholism without the knowledge of the patient. Application in traditional medicine.

Official site:

On the site you can download a Nokia diagram for any model. Download Nokia solution. Find out how to unlock Nokia, SE, LG using UFS, Setool, MXkey programs. How to make a hard reset? Unblock the player, usb modem and completely free of charge, as well as calculate the unlock code. MobiSoft - we think about you!

Nokia phones are one of the most reliable, and often even the owners of modern smartphones do not want to part with their "old friend", using it as a backup option. And some simply do not want to change Nokia to a more modern phone, since they are completely satisfied with it.

But even with these gadgets, troubles happen. For example, the nokia asha 200 phone is a great usable model, but it happens to freeze. The cause may be shock, water ingress, memory overload, operating system failure.

It happens that there is no way to get into the phone repair service. Something you can do yourself. For example, clear memory by deleting unnecessary SMS and contacts. If your phone gets wet, try drying it by removing the back cover and removing the battery. It will take 1-2 days. If the phone does not work after that, it means that the contacts have oxidized. Try cleaning them with rubbing alcohol, acetone, or a special oxide remover. If this did not help, then alas ... This means that the liquid has thoroughly spoiled the microcircuits and you cannot do without replacing them. And it is better to do it in the service.

If you still want to try self-soldering microcircuits, wiring or a pad on the board, you will need a hair dryer to warm up the microcircuits, flux and rosin. You can only warm up those that are not filled with a compound - a special resin. But if you really need to, there are liquids for removing the compound. Now we act according to the following algorithm:

• we warm up and remove the microcircuit;
• we clean the remnants of the legs on the microcircuit and the board with a soldering iron;
• we put the microcircuit on the stencil, making sure that the holes of the stencil coincide with the contacts of the microcircuit;
• cover the holes with BGA paste;
• heat the paste until the lead balls appear;
• wait for cooling, then remove the stencil;
• heat the microcircuit to the board with a hairdryer.

Replacing the glass is easy. It must be greased with soldering fat and heated with a hairdryer. Then clean the contacts on the board to zero with a soldering iron. After that, put a new glass and warm it up with a hairdryer.

Nokia software repair is a job for specialists. It is necessary to understand the firmware configuration: which files are responsible for which functions, as well as many other nuances. It is better for a beginner not to take on this and take the phone to the service, but such trifles as a crack in the glass are an excuse to train their skills.

+7 499 917-08-18
+7 812 603-49-74

You have become the owner of a wonderful Nokia 206 dual SIM phone, but it broke at the most inopportune moment? No problem, just contact our service center and we will help you fix any problem. Short terms of repair of Nokia 206, two SIM-cards in Moscow and a satisfied customer - these are the main principles of our work in the service market.

Convenient phone with support for two SIM-cards, made in a classic plastic case. Powered by the Series 40 platform, equipped with a small but bright 2.4-inch display with a resolution of 240 x 320 pixels. It will delight you with memorable pictures of modest quality, because the Nokia 206 has a 1.3 million pixel camera with digital Zoom 4x and the ability to record video. Keeping pace with the times, the phone is equipped with all wireless communication interfaces.The volume of internal memory is 64 MB, expandable by means of a microSD memory card. An impressive battery for such a phone has a capacity of 1110 mAh, which is quite enough for uninterrupted phone operation during a call up to 20 hours.

Replacement of the display (glass) of the Nokia 206 mobile phone (two SIM cards)... Most often, when using phones, the display beats. If you break the screen or damage it by careless pressing, we will replace it within 1-2 days.

Replacing the flex cable of the Nokia 206 mobile phone (dual SIM). If the display of your phone has stopped showing the image, but the device itself continues to make and receive calls, then the breakdown may be due to a malfunction of the loop. If we have the necessary components in stock, we will replace the flat cable in your phone in no more than 30-60 minutes.

Replacing the microphone or speaker Nokia 206 Dual SIM. If you cannot hear the caller during a conversation or cannot hear you, then we offer a quick and inexpensive replacement of the microphone and speaker.

Replacing the Nokia 206 Dual SIM Charging Slot. Has your phone stopped charging over time? Due to wear and tear or the use of a poor-quality charger, the charging connector may become unusable. If we have spare parts in stock, we will replace the connector in 30-60 minutes!

Software update and configuration Nokia 206 dual SIM. Has your phone stopped working, freezes or turns off by itself, does not respond to button presses, loads slowly, or does not have enough memory? You need software firmware, which our programmers will easily and competently make for you!

Our specialists have a very large positive experience in repairing phones, they are technically competent and responsive. We are glad to offer you favorable prices for high-quality repair of Nokia. We value our reputation, so users who turn to us for help are always satisfied with our service!

We understand your feelings when you urgently need to repair your Nokia Lumia 720 smartphone. Therefore, we work every day from 10-00 to 20-00 except Sundays and holidays.

The prices indicated on the website include the cost of the main spare parts and labor.

Please note that the final cost of the repair is determined by the engineer after the diagnostics.

Order repairs on the website and get 10% discount from the cost of work and spare parts!
All work performed and replaced spare parts are provided 30 days warranty.

1. Diagnostics is free if you agree to repair, if you refuse to repair, the cost of diagnostics is paid in the amount of 400-600 rubles.
2. The time frame for each repair operation is approximate and depends on the availability of spare parts in stock.

This morning, literally grief happened, my favorite phone, Nokia 920 hung on the logo and didn't want to do anything. I ran to the service, was the first customer, the girl at the reception took him in her hands, just pressed all the buttons at the same time and it miraculously rebooted !! The girl checked for basic functions after that, everything worked. Didn't even have to leave it for repairs !! I am so glad. Thank you very much, the girl at the reception. It is immediately evident that they take their place and really understand the technique.

My old Nokia C3-00 began to junk, I decided to immediately go to MT-Service, I'm very used to it and I love this phone. Constantly, during work, a white screen popped up, the guys asked for it for an hour, after which they returned it and promised that this would not happen again. And it really helped, I have been using it for 3 months already, everything is fine. The telephone can still serve. Thanks to the masters and the entire team of the service center, give a second life to our technology.

I managed to break the display into Nokia 925. I changed it somewhere in the basement service for 5000 rubles, began to peel off after a week. I went to them, they blessly returned the money, saw and recognized their joint. They put my old display back. I decided not to take any more risks and turn to a normal service. Replacement cost more, of course, but the mean pays twice as they say.My advice to everyone, do not skimp on this business, it is better to pay 3-4 thousand more, but be sure that you will serve for more than one year and that nothing will come off. I am satisfied with the repair, thanks to the good craftsmen.

We contacted the SC with a broken screen on a smartphone. Here it was replaced for us in just a few hours, Carefully, no signs of repair! very satisfied with the work! Not cheap, of course, but with a discount, issued on the site - it is quite acceptable. Satisfied, never regretted that they came here.

I would like to express my gratitude to the service workers for their friendly attitude and for the prompt, and most importantly - high-quality work! I handed over a lumium phone for repair under warranty, prepared for 45 days without a phone and painful expectations. However, the next day the phone was ready. Works properly to this day. Satisfied and recommend!

I want to express my gratitude to this service center for the work done on my Microsoft Lumia 950 DS device. I handed over the device to replace the front panel of the phone, the screen dripped from the impact and the sensor did not work. The work was done very high quality, the spare part was original, a nice price. Very happy, thank you!

The phone is lumiya730, the glass in the upper right corner began to recede. In the service, within ten minutes, they made a diagnosis, after which they told me that this was a warranty case and offered to leave the phone for repair, but they immediately warned that my spare part was out of stock and I had to wait. I waited eight days, after which my status on the site changed to “the device is ready to issue”. I came and looked at the phone and my joy was not there, my lumiya was as good as new. Special thanks to Po for your attitude to work, keep it up.

We repair Nokia mobile phones using original spare parts, repair documentation and equipment approved by the manufacturer.

Our technicians have sufficient experience to carry out high-quality diagnostics and repair of Nokia phones. Diagnostics, as a rule, takes 1 day, and repairs on average take up to 3 days if the necessary spare parts are in stock.

By choosing a model, you can learn more about the cost of the services provided and receive additional bonuses for repairs.

Our service centers are authorized for warranty repair of Nokia cell phones.

By contacting us, you can count on the professionalism and experience of our engineers who will help you with any difficult situation. Repair on a warranty basis is free of charge, subject to warranty obligations (no mechanical damage, no traces of moisture and unauthorized repairs).

We are waiting for you in our service centers and will be happy to help with solving your problem.

Federal company "MT Service" is a network of authorized service centers for the repair of phones, smartphones, tablets and other digital equipment.

Most likely, judging by the described percentage, he died (Often happens), but first check the BSI and the elements sitting on it! And try to throw off the D2750 (If you say that there was water in the sim area). This is for a start.

TS if I understood you correctly, you turned on the TA, it worked and went out.

Well, if so that the percentage (You can remove) the KP is alive in it. See the binding of the Battery Contact and discard the mikruhu (Apply voltage and go through the elements that are on v_bat for a drawdown). And describe what consumption with KNP on and without it. (If with the included consumption is too high, see what is heating)

But this is for a start. In general, you need to start with Diagnostics (Voltage measurements, Visual inspection, etc.) and not roll everything + info boxes would not be bad here.

Frequently Asked Questions - A collection of frequently asked questions on a topic and answers to them. In our FAQ on Nokia and Microsoft, we have tried to collect the most popular questions and answers to them found on our forum. In order to find what you are interested in, just select your Nokia or Microsoft model from the list or use the search.

Where can I find the technical specifications of the Nokia 206 Dual SIM?

What are the differences between a smartphone and a regular phone?

Can you listen to the radio only with wired headphones connected?

How to make your phone / smartphone work longer?

1 minute burning
backlight = 1 hour in Standby mode.

10 seconds of work with
menus = 15 minutes in Standby mode.

1 minute reception
network information = 30 minutes Standby.

One registration for
next Base Station = 1 hour in Standby mode.

Switching on the phone with
search and registration in the network = 2 hours in Standby

What does “gray” phone mean and how to tell “white” from “gray”?

“Gray” or “White” (not to be confused with Chinese forgeries) does not affect the quality of the product. “Gray” is considered to be an apparatus officially produced for the domestic market of country “A”, which for “unknown” reasons is sold in country “B” (for example, in Russia), that is, imported into it bypassing customs and tax authorities - and therefore cheaper (and, as a result, does not have a Russian keyboard layout, or it is “cut” by a handicraft method).
A device legally manufactured at some German plant, illegally located in Russia ("gray"), will not work worse because of this, but the buyer does not purchase no guarantee and in the event of a breakdown he will not be able to contact the SC for free help.(only in the SC of the country for which the device was released). The "gray" phone was initially non-Russian (or again in a handicraft way) - it can be flashed into Russian, but the Russian keyboard (if it is not there) will have to be bought somewhere separately.

What you need to pay special attention to when buying a “white” device:
- -Check for the presence of the conformity marks of the Telecommunication Certification System (SSE) and Rosstandart (RST) on the stickers on the packaging and in the phone under the battery. All these data (PCT, IMEI, country of manufacture, manufacturer's name, etc.) under the battery should be applied in the form of just one sticker (separately glued “PCT” and so on - a clear sign of “grayness”).
- -Make sure that the IMEI on the package, under the battery and in the phone is consistent (by dialing * # 06 #).
- -Check IMEI with the manufacturer (by calling the Russian representative of the manufacturer's consumer support). Nokia Care hotline: 8 (800) 700 - 22 - 22. Calls from Russian regions are FREE.
- -Check availability original instructions on Russian language.
- -Check for the presence of original films on the display and case.
- -Presence of a Russified keyboard.
- -Check the complete set according to the instructions.
And buy in a more or less decent store, and not in the transition 🙂. On the Nokia's website there is a list of authorized dealers, where you can find stores in your city.

When the phone is on charge, the vibration alert does not work - is that how it should be?

Today I want to talk about the repair Nokia C7-00 with a camera that does not turn on. Outwardly, all signs of poor contact in the camera holder, but it turned out that is not quite the case.

I invite my readers to get acquainted with the next repair from Pavel, this time he received it for repair Nokia X2-02 with partially disabled buttons.

I haven't described repairs for a long time, today I want to talk about repairs Nokia 515 ceased to turn on after a strong fall.

Today again I would like to present an interesting article from the master Paul. In which he very popularly and clearly told how to repair a phone Nokia 500 after contact with liquid, even if there are no suitable components.

Today I want to present a description of phone repair Nokia Lumia 610 , which Pavel kindly shared, thanks to him for an interesting incident from personal experience.

I had a chance to make a simple phone repair Nokia 206 with a problem, does not see the second SIM card.

I would like to describe the repair of a popular phone Nokia 6303ci discharges quickly with a malfunction. In my practice, these come across quite often even now, and the problem is constantly in one microcircuit.

Diagnostics and repair of the Nokia 206 phone is carried out by professional engineers of our service as soon as possible.A guarantee is issued for all types of work. You pay only for the repairs performed.

The prices in the table are for repair work, excluding the cost of spare parts.

All information provided is for reference only and is not a public offer. Check the terms and the actual cost of repairs with our specialists by phone +7 (495) 363-78-55

The Tech-Profi service center is always happy to help in solving problems that have arisen with your phone. Our engineers carry out repair of cell phones of any complexity. From replacing the display and touch glass, repairing the charger and SIM holder, to complex electrical repair of the motherboard. Our service technicians will restore Nokia 206 after flooding or severe mechanical damage at the lowest prices in Moscow.

The addresses of our service centers:

* Discount is provided for the work of the master. Specify the exact cost by phone.

The article deals with the issues related to the repair of the Nokia 206 mobile phone. General points can be useful when repairing other Nokia mobile phones (including the Asha series) assembled on a similar hardware platform.

The announcement of the mobile phone "Nokia 206" took place at the end of 2012. This unit has a classic candy bar form factor and a hardware keyboard. The basic specifications of the Nokia 206 include a 2.4-inch QVGA display, a 1.3MP camera, a microSD slot, Bluetooth and other features typical for mid-budget mobile phones. The device is available in versions with one or two SIM-slots. The main technical characteristics of "Nokia 206" are shown in table 1.

To disassemble the Nokia 206 you need the following tools:

1. Screwdriver with TorxPlus profile # 6.

2. Tool SS-93, which is a paddle made of soft plastic. In its absence, you can use a spatula from a set of children's plasticine.

3. Soft plastic plate, approximately 0.5 mm thick (SRT-6).

4. Tool SS-276 for removing the camera module.

5. Tweezers with curved jaws.

Disassembly of "Nokia 206" is carried out in the following order:

1. Turn off the phone, remove the back cover, remove the battery, SIM-card and memory card.

2. Using the SRT-6 tool, starting from the bottom of the phone, pry off the front panel and, releasing it from the latches, remove it.

3. Remove the keyboard cover.

4. Using a Torx No. 6 screwdriver, unscrew the 6 screws securing the phone board to the middle part of the case (Fig. 1a).

5. Using the SS-93 tool, starting from the bottom of the phone, release the phone's motherboard from the latches that hold it and remove it (Fig. 1b).

6. To replace the polyphonic and spoken speakers, charger connectors and headphones, remove the corresponding elements from the middle part of the phone case.

Table 1. Main technical characteristics of "Nokia 206"