DIY blender knife repair

In detail: DIY repair of a blender knife from a real master for the site my.housecope.com.

A blender is a multifunctional home appliance that is found in almost every kitchen. This is a convenient device that can replace several devices at once. With its help, grind, mix, beat the products. The design of blenders is simple, so they are quite reliable, but even the most reliable technique fails. Consider how to disassemble a submersible and stationary blender, find the cause of the breakdown and do it yourself repairs.

All blenders can be divided into two types - stationary (tabletop) and submersible (hand-held). They differ in design and method of operation, may have different attachments and additional functions. To repair a stationary or hand blender, you need to understand the features of its device.

The hand-held models are long-handled electrical appliances with a cutting attachment. They are dipped into a bowl with products that need to be chopped and mixed, pressed on the start button and held until the procedure is over.

The undoubted advantages of submersible models include compactness. The devices are easy to disassemble for cleaning, plus they need a minimum of space to store them. Blenders with a large number of attachments are versatile and perform a variety of food preparation operations.

There is only one drawback of submersible structures, but it is significant. During cooking, you have to hold the device in your hand while pressing the start button. If you have to do this within 1-2 minutes, the hand gets tired, numb. Such a device is not suitable for frequent use, because does not cope well with mixing large portions of food.

Video (click to play).

Making Soup with a Hand Blender

Stationary models resemble food processors in appearance and often perform many functions. They are bowls with rotating knives attached to the bottom. Such a device is installed on a table, you do not have to hold it with your hands while working. He is able to grind a large portion of food at a time, copes with mixing cocktails, liquid dough.

Desktop models also have drawbacks. The hostess has to allocate quite a lot of storage and installation space. In addition, some stationary blenders do not grind vegetables well: they either grind into crumbs or remain large chunks. The advantages of tabletop structures include the fact that it is sometimes easier to disassemble and repair them with your own hands than submersible ones.

Although the principles of operation of submersible and stationary blenders are similar, there are still differences due to the different design of the devices. In all models, products are chopped with knives, but in tabletop appliances, the bowls also serve as an auxiliary function.

The knife of the stationary appliance, located at the bottom of the bowl, rotates and cuts the food. With an increase in speed, the crushed mass is mixed, rises up. The walls of the bowl expand upward, so small pieces slide along the walls, and large pieces fall into the center - to the knives. It turns out that the crosspiece pulls down the pieces of food and throws the already crushed mass to the walls of the bowl.

It is not uncommon for a blender to be considered broken if it does a poor job of chopping. But it happens that the problem is not in breakdowns, but in the low power of the electric motor. Sometimes it is enough to add a little liquid to the bowl to make the work of the knives easier.

If the model is powerful, then such deviations in operation can really indicate malfunctions, for example, a blunt knife, a broken speed switch, etc. In some cases, problems with the bowl may be the cause of poor performance.

Stationary model device

In submersible structures, collector-type electric motors and fuses are usually installed that turn off the device in case of overload. Frequent breakdown - burning of current-carrying parts, therefore, when a malfunction occurs, first of all, the contacts "ring out" by rotating the shaft by hand.

Care must be taken when using handheld devices: they are not suitable for kneading dough and other thick products. The motor may not be able to withstand the load. Repairs will be expensive. However, there is good news: often women's hands get tired of holding the equipment before the engine has time to overheat.

Many models are equipped with gear shifters. This is a very convenient feature that expands the capabilities of the hostess. But if the engine does not cope, then the working device can break out of the hands, which becomes the cause of mechanical failure.

Submersible model device

In submersible models, the power cable is often damaged. This is the flip side of the main advantage of such devices - mobility. The hand blender is often turned on and off, carried from place to place, which leads to kinks in the cord, incl. critical.

Unstable operation of the power grid is also a risk factor. During power surges, motors often burn, printed circuit boards are destroyed. Often it is necessary to replace the knife, repair the attachment, the speed regulator. In table-top appliances, liquid may leak into the nozzle drive, the bowl snap mechanism may break.

Hand blender repair

Consider how to check the performance of individual structural units:

If the blender does not turn on, the first thing to check is the presence of current in the electrical outlet. Before disassembling the device for repair, you need to make sure that there are no power problems. The outlet is checked using a tester or by connecting to it another electrical appliance, which has an accurately working cord.

If there is current, but the blender does not turn on, check the power cable and fuse. Repair in this case comes down to replacing faulty parts with new ones.

Overloads can burn the motor. In addition to problems with performance, such a breakdown gives off a burning smell. Sometimes the device can be repaired by replacing the brushes on your own, but more often you have to give the blender to a service center for repair or buy a new one.

When the elements of the printed circuit board burn out, a short circuit occurs. It is necessary to disassemble the equipment, inspect the board, test and, if necessary, re-solder the faulty elements.

If the gasket leaks, then it must be replaced with a new one. liquid can get on the electric motor and cause more serious repairs.

Diagnostics of malfunctions of the submersible model

Housewives are often faced with a situation where the blender has stopped and the knife is not spinning. It happens that the knife is spinning, the engine and the speed switch are in good order, but when loading the products, the device runs “idle” without grinding them. In many cases, repairs can be done by hand. Let's figure out how to do this.

Stationary blender device diagram

(KMU: make a screenshot of the 1st picture with the name of the parts)

Before disassembling the blender for repair, you should carefully read the technical documentation. Disassembly instructions may be supplied with Bosch, Philips, Scarlett, Polaris models. It is best to follow the manufacturer's recommendations. Otherwise, there is a great risk of permanently breaking the device.

For disassembly and repair, you will need the following tools:

flat thin screwdriver (if such a screwdriver is not available, it can be replaced with a narrow knife);
long screwdriver;
pliers;
a magnet to reach small parts if you cannot remove them with tools;
superglue or any other reliable adhesive with which you can restore the integrity of the seams if they are damaged.

DIY blender disassembly procedure:

Remove all screws, remembering or noting where they are located.
Remove as many items as possible.

Note! Some craftsmen offer a more radical option for disassembly: a narrow screwdriver or knife is pushed between the body and the casing of the device and the weld is knocked down with an accurate hammer blow. This method is only suitable for non-collapsible models, and superglue is required to reassemble them after repair.

Parts that could not be removed must be carefully examined. They can be clipped. In this case, they can be removed by pressing the latches.
When the case is disassembled, you can start checking the performance of parts and repairing.

The most common models of Scarlett ("Scarlet"), Vitek ("Vitek"), Polaris ("Polaris"), Philips ("Philips"), Bosch ("Bosch") are usually disassembled, so they can be repaired by hand, replaced nozzles. Let's consider in what cases self-repair is possible.

Replacing the knife. If the knife is dull, it can only be replaced, because it cannot be sharpened. New knives are sold in specialized and hardware stores. To replace, remove the old part by wrapping a towel around it and unscrewing it. After that, insert a new knife (it may differ in appearance from the old one), secure.

Important! Sometimes you can buy a new knife complete with an oil seal. It makes sense to replace both parts at once. In some stationary models, the knife cannot be removed from the bowl, because it is not collapsible. Then there remains only the option of a complex replacement of the bowl, knife and gland.

Old and new knives

Speed regulator. In stationary models, it may be difficult to check the switch, because the function of blocking switching on without a bowl is often provided. By the way, the problem of stopping the operation of the device is also associated with blocking. If you suspect a malfunction of the speed switch, it must be evaporated, each position must be checked in full, and repaired.

Stopping work. If the device does not turn on, the first thing to do is check and, if necessary, replace the cord. If it turns on and buzzes, but does not work, then disable the lock. Inoperability when the blocking is released most often indicates a burnout of the electric motor winding. It can be replaced, but this is an expensive repair, so more often than not it is more profitable to just buy a new blender.

Note! The problem might be with the circuit boards. Capacitors and resistors are worth inspecting. If a short circuit occurs, then it is better to give the device to specialists. In many cases, damaged electronics cannot be repaired or the cost is too high.

So that you have to disassemble, check and repair blenders with your own hands as rarely as possible, you should adhere to simple rules of safe operation. Check the reliability of attachments before starting work, do not turn on the device without a bowl, do not overload, handle the wire carefully (make sure that it does not bend or twist). The main thing is to follow the instructions for use. These simple measures are quite enough for the equipment to serve for many years without repairs.

Rack structures on the ceiling are used to decorate various premises, both residential and public. The kitchen is no exception. The popularity of this material.

Someone becomes an adherent of this style at first sight, someone is annoyed by its excessive cloying and "mimicry", but completely indifferent shabby.

The financial costs of arranging a kitchen and a bathroom often account for the lion's share of the cost of repairing an entire apartment or private house. No wonder, after all.

Various food processors are used to prepare various first courses, as well as special foods for children. But due to frequent use, they break down quickly. Repair of the blender Brown (Braun), Turbo (Turbo), Philips (Philips), Bosch (Bosch MSM) and others is not difficult, all work is easily done by hand.

This device is very simple in structure. In principle, a blender consists of an electric motor, a nozzle and a bowl (only for a stationary one). Devices are of two types:

Manual, submersible (Bimatek BL, Kenwood, Krups, Orion);
Stationary (Moulinex, Panasonic, Gorenje, Zelmer).

The manual ones are a motor with a handle, to which a nozzle is attached. The key difference between the hand blender and the stationary hand blender is how it works. Food is poured into the bowl of the stationary, which is crushed by the knives located at its bottom. The manual one is immersed in a container (most often in a special glass) and cuts food at any level.

Photo - hand blender

The main types of equipment malfunctions:

The device does not rotate. This is a knives speed switch problem;
The household appliance does not grind or does not work well. With a mixer and blender, the power of work plays a very important role. If an insufficiently powerful or high-quality type is selected, then the work efficiency will be low;
The device does not turn on. Perhaps there is something stuck inside the shredder or the engine burned out from very intense work. Also, in some cases, this is affected by a decrease in voltage in the electrical network;
Modes do not switch. This is most likely a drive or control problem;
The knife broke. Most common problem. These blender parts are sold in almost any brand store (Vitek, Redmond RHB, Scarlett - Scarlet, etc.), they cannot be repaired, so they are replaced.

Photo - stationary blender

Video: how to fix a blender

Before you repair the device, you need to disassemble it. It should be noted right away that the disassembly of the Brown, Saturn, Bork and Vitek hand blender is impossible. Their construction is molded plastic. A plastic ring is soldered into the base, which cannot be removed. Therefore, there are only 2 options for solving the problem if the device is broken:

Buy a new one immediately. Unfortunately, not every service center will provide warranty repairs for such blenders;

Unsolder the panel. To connect the body, plastic soldering technology is used, therefore, disassembly can be carried out using high-temperature technologies. You need to carefully cut the case and insert several metal plates or needles into the cut. They need to be heated and the molten plastic removed. After repair, the plastic can be glued.

The body contains the working part of the blender - the motor, the spindle, the control unit (a circuit that helps to set the modes, etc.). After disassembly, you can replace the required part with a working one or clean the device contacts.A little more complicated is the case with disassembling a stationary blender. It consists of a specially shaped bowl (often cylindrical or trapezoidal), a knife, an electric motor, a shaft and a spindle. When the device is connected to the network, the shaft with the spindle transmits the torque to the knife, which moves and cuts the food in the bowl. To prevent the ground food from falling out through the extended top, the bowl is closed with a lid. The rotation of the knife can be carried out for a certain number of times (some models of Moulinex, Polaris and Redmond have a built-in timer in the system) or until the contacts open.

Photo - disassembly of the hospital

To disassemble such a blender at home, you will need a screwdriver or wrench, depending on the type of mounts. The housing cover is supported by screws or nuts, mainly with a left-hand thread. They are removed, the body is removed. Underneath is the motor, shaft and spindle. The first step is to inspect the shaft; there should be no jags or obvious irregularities on it. Further, if necessary, you can change the knife:

If the knife is dull, then it will not work to sharpen it - but you can buy it in the company store. Depending on the brand, it costs from 2 dollars to 10. To remove the old cutter, you need to unscrew it from the spindle;
Sometimes the knife is mounted not on the thread, but on the nuts. Then they are unscrewed, and the blade itself is carefully removed from the socket;
An oil seal is located at the junction of the knife and the drive - this is a seal that improves the adhesion of the parts and increases the torque. It must be replaced every six months (if the model is collapsible);
In some blenders Tefal (Tefal), Bork, Scarlet SL-1548 and Cameron, the knife and container are solid, so if any part breaks, you will need to replace both parts.

If the knife is turning too slowly, the speed selector may not be working. The control board is responsible for its work. To inspect it, you need to disassemble the device according to the instructions above and test all the contacts. They should be closed. In this case, be sure to check the power and lock button.

Photo - knives

It should be noted that the operation of the drive is impossible without a tight fit of the bowl to the junction. This safety technique protects you from accidental injury. If the board and the lock button are normal, then you need to test the contacts of the bowl - they may come off. Sometimes, when doing kitchen work, food residues get on the active parts of the device - look at them and, if necessary, wipe them with special substances for cleaning and degreasing.

Photo - hand model construction

In the event of a gearbox malfunction, the blender most often simply does not turn on; such repairs are very difficult to carry out on your own. Instructions on how to replace the engine:

It is necessary to disassemble the device according to the scheme described above. Be sure to read the manufacturer's recommendations and the technical specifications of the device. In non-separable models, such repair is not advisable due to its high cost;
Check the power and lock button - there may be a problem with it. If a buzzing sound is heard when you turn on the blender, then you need to squeeze the contacts and test them with a multimeter. In some cases, they simply cannot close when turned on;
Engines can be bought separately in special stores, but such spare parts are sold separately only for expensive models or for food processors (Kenwood HBM, Polaris PHB, Gastrorag, DEX DHB);
The new engine is installed in place of the broken one, the system is assembled and tested.

Often the reason for the non-working condition of the blender is a broken power cord. To check it, you need to disconnect the device from the network and ring the wire. The cable is soldered to the power head inside the case, you need to check its voltage with a multimeter when connected to the network - if there is a signal, then the cord is working. Otherwise, the cable is replaced. The same can be done with a fuse - it is tested and, if necessary, replaced with a new one.

The blender is a motor with a special attachment on the shaft. This is a fairly simple device. To start working, a bowl with a knife is attached to the motor shaft. This makes it possible to disable the engine blocking. After the blender, you can work in a pulse or normal mode by pressing the power button. The household appliance is completed with a speed controller, cord, plug. A fuse may also be included.

Are you sure you can handle a DIY blender fix? In this article, we will show you how to disassemble a blender and how to become a near-professional blender repair master. Like most devices, the blender is easy enough to disassemble, the main thing is that there are no unnecessary parts left during assembly.

Today there are three types of blenders available:

Stationary
Submersible
As an option in a food processor.

In all kinds of blenders, the main component is an electric motor. But the principles of operation of a household appliance are somewhat different. Stationary blenders are almost identical in performance to food processors. They consist of two main components: an electric motor and a cookware with a knife placed inside it.

Let's look at the device and how the blender works. Food is placed in the blender bowl. The device turns on and its knife starts to rotate very quickly. The shape of the knife is designed to make the products move in a closed path. The knife of the device is located at the bottom of the bowl and mates with the rotor of the engine. High speed and the right shape allow you to quickly chop the food. The blender blade is shaped like a propeller. This allows him to draw in products for cutting, and at the same time throw the already chopped mass onto the walls of the bowl.

The blender bowl has a special shape that allows the movement of the processed products in a circle. The walls expand towards the top. In this regard, the resulting mass begins to fill the walls, freeing the center of the mold for not yet cut products. As soon as the number of processed products on the wall reaches a critical weight, they fall back onto the knife and further chopping takes place. In practice, all this happens in a matter of moments.

We have described the process that can be observed with quality equipment. Cheaper models may not cope with the task at hand. Lack of power does not allow creating a continuous flow of processed products and the knife begins to cut the air. If you decide to chop the cabbage, add a little water. This will help the knives handle this vegetable.

If the blender does not cope with chopping food, this does not mean that it is broken, it may simply not have enough power. Then add some liquid and try starting the blender again. If this does not help, then perhaps you should do the repair yourself:

sharpen or replace the knife;
test the speed switch;
make sure the engine is working properly;
check how the bowl connects to the knife.

If you decide to repair the blender with your own hands without involving professionals, then you should start by checking the speed regulator. It's simple. It is necessary to press successively different speeds and determine by ear whether the speed of the rotor is changing. If the speed changes, then the regulator is working, and it is worth checking the blender knife.

Read also: DIY viburnum mirror repair

Do-it-yourself blender repair in most cases means disassembling the case. Most branded models provide for this, but there are also non-separable models. In the latter case, it is worthwhile to disconnect the housing elements with extreme caution, and use adhesives when reassembling.

The malfunctions from the table below are typical for any type of blender:

The knife in the attachment or chopper bowl may be less effective at grinding, tearing, or seizing pieces during use. Repair of the grinder in this case consists in replacing it, since the knife cannot be sharpened.

How to disassemble the blender chopper:

press the axis of the knife with your finger;
pull it up in a rotating motion.

In most bowls, the knives are removable, and if not, then the problem will be solved only by replacing the bowl.

If the knife is blunt in the leg of the hand blender, how do I repair the attachment? In this case, you can either purchase a new one, or disassemble the attachment, replacing only one knife.

If the unit stops working, the problem is probably in the fuse:

disassemble the case;
remove the fuse;
we replace it with a new one (the price of a new part is very small).

If the blender does not spin, although it buzzes and clearly shows signs of life, then this may be a malfunction in the engine winding.

It is not recommended to repair it yourself. Try to get a new engine, otherwise you will have to go to the store for a new blender.

When, it would seem, it was possible to determine the malfunction, to change the part, but it turned out that the device does not turn on again when it is subsequently turned on to the network, then this is probably a short circuit.

In this case, you cannot fix the problem on your own. Such damage cannot be repaired.

We examined the most common blender breakdowns and how you can fix them without contacting a service center. I hope that a detailed description of the problem and its solution will help you cope with the repair yourself.The video in this article provides visual instructions for fixing blender breakdowns.Have questions? Ask them in the comments!A blender is a must-have tool in the kitchen. Almost every housewife has it, because it is very convenient and practical. And if the blender does not work, many people feel severe discomfort while cooking. After all, it is indispensable during chopping, whipping and mixing food. However, do not despair and immediately contact the workshop, since some faults can be repaired on your own.Why isn't the blender working?To understand how to repair a blender with your own hands, you first need to know how it works. So, today two types of these devices are produced:

Stationary.

Manual or submersible.

But there is also a blender, which is part of a large and multifunctional combine. In this case, if there is a breakdown, the whole device does not work. Therefore, in this article we will only talk about how to calculate the cause of the breakdown and repair a stationary or hand blender. Image - DIY blender knife repair

Hand or hand and stationary blender

Regardless of the model, kitchen utensils have several basic mechanisms that enable them to work. First of all, it is a motor, various knives and attachments, the number and types of which depend on the model, as well as a bowl. In some of them she can perform a remembering role.

A reed-shaped device equipped with several attachments. Its main difference from the stationary one is the absence of thickets. At the same time, this enables housewives to perform all manipulations in a variety of containers. Its body contains the following:

During his work, the hands of the cook are free. The device has a base on which the bowl is installed. The cutting attachments are located in it. Repair of this type of device is somewhat more difficult due to the presence of a large number of parts. It consists:

bowl with lid. It can be glass or plastic, depending on the model;
engine;
spindle;
knife;
drive shaft;
locking mechanism.

It should be noted right away that not all devices are capable of grinding products equally well. For example, low-power models are not able to cope with solid food, so if your blender does not work, or rather does not cut food, this does not mean that it is broken and needs repair. If after turning on the device starts to hum, but no process occurs, you need to check two things:

whether the knives are spinning if they are not obstructed by food. If so, this means that your device is simply not able to cope with such a volume, and it does not need repairs. To do this, you either need to add liquid or reduce the amount to be ground;
in some cases it may not cut due to blunt knives.

In the first case, you will not do anything, since your model is very low power. But how to replace the knife, we will describe below.

Check the blender before disassembling!

Important! You will not be able to sharpen the blade manually at home.

There are two options for the development of events:

Go to the workshop with a request to sharpen a knife. However, it must be said right away that most of the craftsmen will tell you to buy a new one.
Get a new knife. They are now sold in almost all stores. To do this, you need to know the model, but it is better to go in search with a passport or with the device itself. Most often, they are sold together with oil seals, so you need to replace it immediately.

Before handling, unplug the device from the socket, otherwise one careless movement may lead to loss of fingers!

Removing and replacing a knife with your own hands

To remove the old knife, you will need a towel. Grasp the cutting part with it and unscrew it from the spindle.

Note! You need to scroll to the right!

In some models, the knife can be fixed with several nuts, so you need to arm yourself with a wrench or pliers.Sometimes, but in rare cases, to dismantle the knife, you also need to disassemble the bowl.

After replacement, you need to put everything back and fix it securely. Only after that, turn on the device for testing.

Here everything is a little more complicated, so a more complete disassembly and repair will be required, since there can be many causes of malfunctions, and here are the most common ones. Disassembling the hand held device is not difficult. To open the case, it is enough to correctly set the places on the handle, locate the latches and open them.

It is more difficult to disassemble a stationary model, in addition, it has much more parts and mechanisms. Therefore, you need to arm yourself with everything you need at once. You may need several types of screwdrivers, pliers, tweezers, indicator screwdriver. It is very important, especially if you are doing repairs with your own hands for the first time, to remember where and how all the mechanisms are installed. Otherwise, you will carry a blender for repair with no more serious malfunctions, for example, a short circuit, a burned out engine.

DIY blender repair

Unfortunately, unless, of course, you are a radio technician, DIY repair is very difficult, and sometimes impossible. Since not only special tools are needed for this, but also knowledge in physics. If your blender has a broken speed switch, it is best to contact a specialist.

But if you do decide to do your own repair, get ready for the fact that you will need to disassemble the blender. So, armed with a screwdriver, we unscrew the case of the device. You need to remove all parts to free access to the switch. The regulator is evaporated from the equipment and then checked in all positions. If the blender is working properly, the contacts will be correctly set at all speeds.

Important! Before proceeding with the repair, you need to listen to whether the speed changes in different positions of the switch.

Speed switch repair

Sometimes it happens that the device simply does not turn on. There can be many reasons, as well as ways to eliminate them, so let's start in order.

The most common is knife jamming. To determine this, you need to turn on the device and listen: if there is a buzzing, then the reason is established. To eliminate it, you need to remove the bowl and very carefully, it is better to do this with a foreign object, squeeze the power-on lock button. Great, everything worked - the repair was limited to removing the bowl and knife.
The problem is much more interesting, but also more deplorable when buzzing is heard, and the lock button is released, but the process does not occur. Here, the forecast is disappointing - the motor winding burned out. There are several solutions here: contact the service center with the question that the blender most likely burned out and whether it can be properly repaired or disassembled and try to independently establish the cause.

The first sign of a burnt out engine is a strong burning smell, which occurs when a short circuit occurs in the system. Repairing it is possible, but only if it is limited to replacing brushes. In other cases, it is cheaper to buy a new household appliance.

It is important to understand! Buying a new device in many cases will be more profitable, since the price of the motor is very high.

We check the most common causes of breakdowns

In this case, there are many breakdown options. And most often, housewives begin to panic even in cases where there is no problem as such:

Before proceeding with the repair of the blender, you need to check the most elementary thing - the operability of the outlet.
If this is not the reason, then one more thing must be excluded - wire breakage. To check the cord, you need to disassemble the case, so you need to take a set of screwdrivers. Rare models may require you to use special attachments, but, as a rule, a regular cross or flat is sufficient. Before disassembling the blender, it must be disconnected from the power supply.And only after that open the case. After it is separated, a power block will appear in front of you, to which the cable will be soldered or screwed. At the connection points, you need to check the voltage with a special screwdriver. If it is, then everything is in order with the wire, but if it is missing, it is better to connect a new cord.

Checking the wire in a blender

As you can see, the malfunctions and methods of their elimination are not as complicated as they might seem at first glance. Therefore, if you need to fix a broken blender, do not rush to go to the workshop, try to eliminate the causes yourself.

The blender does not always break down due to electrical problems, often the causes of the malfunction can be ordinary mechanical damage, which can also be successfully dealt with at home.

If, during the operation of the device, a leak is detected between the body and the bowl, it cannot be postponed. It is necessary to disassemble the bowl, nozzle, whisk, then remove the spindle. A gasket will be opened in front of you, which is the culprit of the breakdown. To fix the leak, it is enough to replace it with a new one.

A blender, however, like any other technique, can be damaged during operation, especially if it is sloppy. Most often, the latches located on the lid and additional nozzles are susceptible to damage. Most often, such damage cannot be repaired, since it is very complex and short-lived. It is better to go straight to the store to purchase attachments.

However, do not rush to throw away the damaged attachment, since not every model has spare parts on sale.

There is another weak point in modern blenders - the gearbox. Its frequent breakdown is associated with excessive loading of the device. With frequent and prolonged use, it can heat up, as a result of which its seat and gears melt. This problem can be established immediately - when the device is turned on, characteristic sounds will be heard due to extraneous things.

For DIY repair, you need to disassemble the device and examine it. If the internal mechanisms are intact and they just came out of the grooves, they need to be reinstalled and fixed. If the gear is broken, you need to buy a new one.

Important! Select this part exactly in size!

If the blender breaks down for any reason, you do not need to immediately contact the masters. After all, the reason may be a banal cable breakage or blocking of knives. Before wondering if the blender is not working, what should I do? Check the elementary possible reasons and only after that, evaluate your strengths and capabilities, and only then proceed to self-repair.

Video (click to play).

I would also like to say that some spare parts for this household appliance are very expensive. In addition, non-original spare parts produced do not guarantee long and high-quality work. Therefore, before proceeding with an independent repair or in a workshop, evaluate its expediency. Because sometimes the difference between a repair and a new device can be only a few hundred rubles.

Rate the article:

Grade 3.2 who voted: 82