DIY window mesh repair

In detail: do-it-yourself window mesh repair from a real master for the site my.housecope.com.

The mosquito net is a good helper and "protector" from small insects and mosquitoes trying to fly into the living space. It happens that the mosquito nets fail, and then the need for repair comes. Safety nets can be repaired by hand without calling a specialist.

To know how to repair the mosquito net itself, you need to understand how it works. The base of the mesh consists of four aluminum profiles, which are connected by plastic corners. A mesh is attached inside the profiles, thanks to a cord located in the recess of the frame.

You can find three types of fastening mosquito nets:

Roll. Such nets work on the roller blind principle, that is, a box with a mosquito cloth is fixed at the top of the window, which can be easily pulled down and fixed on the lower part of the frame. Yes, the device is very good, but the price, however, for such a grid is also not small.
Frame mesh. These nets are considered to be the most common ones due to the optimal price-performance ratio: the degree of insect protection is high and inexpensive. The frame mesh is an aluminum profile, inside of which a mosquito cloth is stretched.
Hinged mesh. In this case, there is a reinforced frame, and often swing nets are installed on the entrance, balcony frames. Such a mesh is held on hinges, which are mounted to the door block. On the free side of the frame, there are magnets that prevent the swing net from opening from gusts of wind. Some users do not exclude the installation of such grids on windows.

Video (click to play).

In addition to these methods, there are also homemade, homemade, cheap ways to secure the mesh. Details about the options for attaching mosquito nets.

There are several reasons why mosquito nets break, deteriorate, deteriorate. Firstly, over time, all mesh elements lose their original properties, especially since the profile itself is constantly under the influence of natural conditions: wind, rain, snow, temperature drops. Secondly, the canvas is "clogged" by insects, because of which, in fact, the mosquito net is placed. The integrity of the net is affected by aggressors such as pets and birds.

If the components of the mesh were made improperly, it means that the mosquito cloth will not serve you for a long time. Therefore, it is better not to skimp on the quality of the profile and components from the very beginning of the purchase, then the service life of the mesh will increase significantly.

If you need to change the mesh on a plastic window, you need to remove the cord from the frame. It can be easily removed with a thin, sharp object such as a screwdriver. Together with the cord, the mesh is released and easily removed.

Next, we put a new sheet on the aluminum profile. It is necessary to carefully lay the mesh, starting from the top and fix the canvas in the profile grooves with a cord. You can help fix the mesh in the gutters either with the same screwdriver, or with a ballpoint pen, or with another suitable object.

Replacing the canvas of mosquito nets

As accurately as possible, you need to pull the third and fourth sides of the mesh - make sure that the canvas does not wrinkle, it is perfectly evenly stretched. After completing the installation, cut off the remaining mesh with a margin, hiding it under the profile. As you can see, repairing a mosquito net is easy and short-lived.

Sometimes it is necessary not only to replace the mesh on the mosquito net, but also to reduce the dimensions of the profile itself. This can also be done by hand. First, you also need to pull out the cord and pull out the mosquito netting. After that, the profile is sawn off with a file and you can proceed to the reverse installation.

If you are worried about the safety of the profile, you can walk with glue and, according to the algorithm described above, assemble a mosquito net.

Many people are faced with the issue of broken handles on mosquito nets. Handles are used for installation in a window opening, and, as luck would have it, very often break at the most inopportune moment. Most likely, these pens are not made of the highest quality materials, therefore, under the influence of natural conditions, they become fragile.

Replacing the handles of the mosquito net

The absence of handles in the grid brings some inconvenience when replacing the canvas itself, so we offer a way out of this situation. You can make a hook from a wire with a diameter of about 3 mm. This hook will be an assistant and a solution in the situation of a broken handle on a mosquito cloth.

The bottom line is that you just need to hook the canvas with a hook, then, if necessary, press it back down. When repairing or replacing a mosquito net on a plastic window with a broken handle, hold one side with the hook while pressing down on the piece of the handle. This will allow you to reach the mosquito net profile from the window.

If desired, repairing mosquito nets with your own hands is quite real, you just need to familiarize yourself with the object being repaired and a little perseverance. If a corner is broken in the profile, you need to purchase a new one and remove, clean out the fragments of the previous one. It happens that the piece gets stuck in the profile, then it will be extremely difficult to get it. It is recommended to push the rest of the corner into the profile, you need to be very careful not to make it worse. The replaced corner cannot be hammered with an ordinary hammer, it is better to use a rubber hammer or a block.

Like the canvas itself, the corners of the mosquito net profile become unusable over time, so it is recommended not to wait for the moment when they break. A sign that the corners have worked out their time is their yellowing. It's time to replace parts of the mosquito net.

Replacing the corner of the mosquito net

In no case should you completely disassemble the frame to replace the corners. During the manufacture and installation of the mesh, all the excess canvas was cut off, so now we have no stock. For this reason, we will start shooting only the upper part of the mesh.

In the area of the profile corner, you need to pry the gum with a sharp object and get it only from the upper part of the frame. The mesh itself must also be removed from the groove. After that, carefully disassemble the upper profile bar, gently help with a hammer if the frame parts are firmly connected. We take out the corners and replace them, and then we re-install the profile frame and mesh. If a plastic window sticks, learn how to adjust the sash.

Modern mosquito netting is simple and elegant, and does a good job with its main purpose - to keep mosquitoes and other small flying vermin into the living space. But, in spite of the correctness of the well-known axiom of technicians: “the simpler, the more reliable”, sometimes there is still a need to repair this product, which is necessary in the house. Let's take an example of how to repair a mosquito net with your own hands without resorting to the help of manufacturers.The basis of the mosquito net is made up of four specially shaped aluminum profiles, connected by plastic inserts in the form of corners. When assembled, the grooves of the profiles form a recess along the inner perimeter of the frame, in which the mesh is fixed using a special cord.Frame assembly diagram. In the center of the picture there are images of the connecting corner and profile.In my case, two mosquito nets required repairs at once. In one of them, cheeky sparrows pecked at the netting. It looks like something edible in their eyes was stuck in the net, maybe a spider or a seed, and they only had to interrupt a couple of threads. And after that, the hole parted so much that mosquitoes began to enter the room. The second grid needed to reduce the overall dimensions - height and width (the neighbors asked).First, the cord is removed - I just forged it with a thin screwdriver sting at the junction and pulled it out, trying not to stretch it in length. (Perhaps this is superfluous - he is not so elastic). The mesh came loose and I took it off.Two photos at the stage of disassembling the mosquito net.Now it was necessary to install a new mesh fabric. Approximately orientated it and began from the upper profile to gradually lay the cord in a circle in the groove, fixing the mesh in it. Used the same screwdriver. It turned out not to damage either the mesh or the profile, although a couple of times the screwdriver jumped off dangerously. Whoever wants to repeat - I recommend working with something less dangerous, for example, the blunt end of a ballpoint pen.The stretching of the third and fourth sides of the mesh is most responsible - I had to redo the corner so that the mesh would not wrinkle. At the end, I cut off the excess mesh with a sharp knife flush with the profile.This is the result. The bottom mesh is overstretched.It turned out fine. The photo shows in comparison that the quality of performance is inferior to the factory one. But collectors use some kind of special roller to lay the cord into the groove, and there, of course, it turns out more accurately.The repair with the second mosquito net went already easier - in the same way I pulled out the cord, removed the netting. I disassembled only two diagonal corners of the frame, carefully pulling out the plastic connecting corner from the aluminum profile. It is held only by friction, but it is pressed in with effort.Then I sawed the frame profiles in length, walked a little along the edges with a file and proceeded to reassemble. Although the corners were held tightly, just in case I dabbed a little bit of Moment glue. And then everything follows the worked-out grid installation scheme, as I wrote above.After all that was done, it became clear to me that the service life of the net itself is much less than that of its aluminum frame, but anyone can replace the mosquito netting of a plastic window. You just need patience and accuracy.Everyone knows the problem of mosquito nets in modern plastic (and not only plastic) windows, whose handles break at the wrong time, intended for installation and dismantling into the window opening. Obviously, these pens are made of substandard plastic. Under the influence of the environment, the material of these fasteners becomes soft and brittle.Without these handles, it is very problematic to insert a mosquito net into the window opening. For a quick solution to this problem, I propose the following option. I think that everyone will have a piece of steel wire with a diameter of 2-3 mm. I made a hook from the wire.It is very easy to pry on, hold and press the net with this hook. With one hand I hold the net with a hook, and with the other, pressing on the fragments of the mounts, I help to insert the mosquito net into its seats.After the mesh is inserted, it is easy to remove the hook through the remaining slot by turning it slightly.This method, of course, does not repair the mosquito net, but it allows you to quickly install or remove it from the window. Image - DIY window mesh repair

The mosquito net is a necessary accessory that can protect the room from insects; it is attached to both wooden and metal-plastic windows. Most often, special grids with a frame are used for this purpose. They are easy to install and can be removed if necessary. Mosquito net handles will do this, but over time they break and need repair.

Most often, buyers purchase a model with an aluminum frame, which is fastened with plastic corners. In order for the mesh to hold, the profile is equipped with a special groove designed for a rubber cord: it fixes the mesh in place, keeps it taut. Sometimes manufacturers install special handles for mosquito nets., with which the frame can be installed in special brackets: they are located on the street side of the plastic profile. Such fasteners allow, if necessary, to remove and install the mesh.

If the plastic fasteners of the mosquito nets break, they can be made using the metal yourself.

Any model of the frame can break. Most often, they are exposed to wind and ultraviolet radiation, which can cause the structure to break or crack. Most often, the problem concerns windows facing south.

Often there are no handles on the mesh, which is why it is quite difficult to pull it out, it becomes even more difficult to put it in place, since the fasteners are located on the outside, and it is impossible to stick your fingers there. In this case, it is not difficult to make handles for mosquito nets with your own hands.

If you want to reliably repair your mesh, purchase Z-shaped holders and special handles. This will allow you not to return to the problem every year.

In order to fix the breakage of the mesh for a plastic window, you will need to do the following:

Remove the product from the holders. To do this, you need to pull on the handles: they are usually attached to the mosquito net along the perimeter.
You need to start by releasing the lower holders, then you can pull out the structure from the upper ones.

If you see that the corners are in a deplorable state, you should not wait for them to break, in which case you can lose the mesh that has fallen down. Replace them beforehand. For this procedure, you should not disassemble the structure, otherwise it will be impossible to assemble it, since the mesh is cut off after tension at the factory, you will no longer have a surplus.

You need to change the planks one at a time, starting from the top. Remember to remove the rubber bands from the corners. You can pry it off with a screwdriver. Do not pull out the entire elastic, loosen the top notch from it, then carefully remove the top bar. If the part doesn't come off, you can try knocking it out with a small board and hammer. After that, using pliers and a screwdriver, you can remove the plastic corners and replace them with metal ones. Assembly takes place upside-down.

If the handles of the mosquito net are broken, not everyone knows what to do. Pulling out such a mesh will be problematic, and not everyone can figure out how to install new handles. Despite the fact that many nets are designed for frequent use, even the highest quality construction is not immune from the trouble of broken handles.

Most often, you have to think about how to replace the handle of a mosquito net at least once every two years. Less often, this element is able to last longer. Having changed it once, you will understand how this is done, and you can easily make a replacement yourself. The procedure usually does not cause problems and does not require hiring a professional who repairs plastic windows.

The easiest way to repair a broken handle on a mosquito net is to screw a small self-tapping screw into the crossbar to help hold the frame. For complete convenience, cut a ribbon from a plastic bottle or find a ready-made ribbon.

We wrap the self-tapping screw into an aluminum profile. It is easier to do it with a screwdriver, but if you try, it is quite possible with a screwdriver

For convenience, make a loop from the material at hand.

First of all, to repair the do-it-yourself mosquito net handle, you need to buy a kit suitable for repair. This is usually not difficult to do: such items are sold in the same place where there is fittings for plastic windows. These are either large construction stores, or companies that produce custom-made plastic windows. If you just ordered plastic windows, do not be lazy to immediately purchase several repair kits for window screens. First of all, you need metal corners instead of plastic ones and some spare handles.

Gently lift the sealing cord with a knife

Install new handles and crush the cord into place

If you order the mosquito net separately, ask the technician to install the metal corners right away, this will save you the trouble of repairing the mesh frame after a few years. This replacement will slightly increase the price of the mesh.

If your design has a cord, please note that you do not need to remove it. In order to make the pairing of the handles less, it is enough to use a flat screwdriver or scissors. The element can be reached, but you must act carefully, otherwise there is a risk of breaking the mesh. It is not recommended to take it off during work, it is not always possible to put the mesh back: this will add unnecessary trouble to your work.

After you have been able to remove the old handles, you need to leave the new ones in their place and clamp them so that they do not fall off. Take care not to damage the cord or net, otherwise the structure will require more serious repairs.

If the cord breaks, there is no need to replace it entirely. Take the desired piece from the repair kit and insert the missing piece.

You can simply install a mosquito curtain on the balcony door. Read more in our article "Mosquito curtains and curtains".

A do-it-yourself mosquito net is made quickly and inexpensively. Read on our website how to make a mosquito net on the window with your own hands?

It is not always possible to find a repair kit on hand. There are situations when the net needs to be urgently pulled out, but there are no fittings for it, in this case the handles for mosquito nets with their own hands will help to get out of the situation. It will not be exactly what in the traditional sense can be called a handle, but the item is quite suitable for conveniently pulling the structure out of the mountings.

You can use this option even if you do not want to put the same fragile and unreliable parts instead of a damaged set of elements made of low-quality plastic. When the handles on the mosquito net are broken, what to do if there is no repair kit at hand, you do not have to guess. All you need is steel wire thick enough to make a hook that won't bend under light load. If there is no wire in the house, it can be bought at almost any hardware store, it is inexpensive.

With the help of the resulting hook, you can easily pry the structure from the bottom and release it from the grooves that hold the frame in place. It is most convenient to remove the mesh by pressing down with a key the places where the fasteners were before.

If the handles on the mosquito net are broken, there are two ways to solve the problem: replace them or use hooks that will allow you to easily remove the structure if you need to dismantle it.

But these seemingly comfortable mosquito nets have flaw - if the frame itself is often made of an aluminum profile (there are also plastic ones), then the corners, Z-shaped holders and handles are usually plastic.

They are the ones that most often break: crumble and crack. This happens especially quickly on nets that protect windows facing south or west, i.e. are actively and for a long time illuminated by the sun.

Corners, Z-holders and handles are replaceable, and to renovate mosquito net do it yourself.

Now appeared metal corners, Z-shaped holders and handles for mosquito nets. I recommend finding just such corners, holders and handles to do not repair mosquito net yearly.

Removing the mosquito net with Z-shaped holders. To do this, lift the net by the handles. up before stop... We deduce lower the edge of the net outside the lower holders. A little omitting mesh down and release the top edge. Outside unfold the windows so that it goes into the window opening.

Replacement of corners.

Better not to wait for the corners to crack and break. Severe yellowing plastic corners are a clear sign that they need to be changed.

To replace corners do not try disassemble the whole frame at once... The fact is that pulling the net itself later will very difficult or even impossible... When making a mosquito net, the net is cut off with a margin, pulled and only then, the excess is cut off. We already have no stock.

Therefore, first we remove only the top the bar.

From the corner we pry a rubber band, for example, with a screwdriver.

We take out the gum only from the top groove. We also take out the mesh from the groove.

We try to pull the top bar up with our hands. If it doesn't work, then turn the grid over grooves for gum down. Covering the grid cardboard so as not to accidentally tear.

With a plank and a hammer knock out the top bar, tapping on one side, then on the other.

From the blows, the corners begin to go out of the frame.

We also first try to remove the corners from the removed bar with our hands, and if it doesn't work, then knock it out with a hammer. Press one edge with your foot (hand), and knock out a corner from the other edge.

It is possible that in this case some corners will break or they were already broken initially. This not scary... Using a screwdriver and pliers, we take out the remaining parts of the corners from the hollow metal frame, being careful not to damage it.

If all the plastic breaks off at the edge of the frame, and part of the corner remains inside, then we drill leftovers with a small drill approx. 3 mm in diameter.

If you cannot pull out the remnants (there is nothing to catch on), then just push them further inward.

Assembling the frame in reverse order. V upper insert the bar with metal corners.

They fit very tightly, so we hammer them with a hammer through a wooden spacer so that do not damage corner and do not peel the paint off it.

We hammer until the corner tightly will not dock with the bar.

Upper plank with corners simultaneously we insert into the holes of the side plates.

Resting the lower end of the frame against a stationary object (for example, a plinth or lifting the frame vertically - to the floor), we hammer the upper bar with corners through a wooden gasket until it stops, tapping with a hammer, then from one or the other corner.

We straighten the upper edge of the mesh, stretch it a little and slowly start tucking the cord into the groove.

Carefully! Do not tear the mesh or cut the cord.

If the cord is difficult to fit into the groove, then it can be wet water and a little lather.

In the same way, we change the lower corners on the lower plank.

That's the whole frame repair, and they told me in the window hardware store that I could not cope with it. That it is very difficult, and only a professional can handle such repairs. Of course, I had to tinker with the first mesh for almost an hour, but I spent only 30 minutes repairing the second mesh.

Replacement of Z-shaped holders.

Replace holders much easierthan to change corners.

Unscrew old Z-shaped holders.

Checkingwhether the mounting holes on the old and new holders are the same.

There are a little holes on my holders did not match... In order not to drill new holes, I just took screws smaller diameter.

We fasten upper holders.

But with the lower no need to rush... The fact is that plastic and metal holders different heights. If you change corners, then dimensions framework decrease and the corners can be screwed into place.

But if you are do not change, and screw the lower holder to the old place, then the frame can do not pass between the edges of the holders.

So in this case (if the corners do not change), before removing the mosquito net from the fasteners (holders), lift the net up until it stops and pay attention to the gap between bottom edge of mesh and top edge bottom Z-shaped holder. If the gap is minimal or 1-2 mm., Then the holes in the metal-plastic frame for attaching the lower holder will have to overdrill... If the gap is about 6-7 mm., Then you can attach the lower holder to the old place.

If the gap is minimal, then measure difference in height between the old and new holder.

Usually it is 6-7 mm. It is for this distance that you need below the old holes drill new holes.

We do the markup with a pencil.

We drill a hole. Plastic is drilled very easily.

We fasten the holder with a screw, align it. Through the hole drill a second hole in the holder. We screw in another screw. We also fasten the second lower holder to a new place.

Now you can put the mosquito net in place.

We set the grid in exactly the same way. how was filmed, only in reverse order... By tilting the mesh, we take it out of the window opening. We insert into the upper holders, lift up to the stop.Pressing the mesh tightly to the window, we bring the bottom edge into the lower holders. Omitting grid all the way.

Replacement of handles.

There is more on the mosquito net one weak point - plastic holders for raising and lowering the net during installation - pens.

To replace the handles, we pry the elastic band from the nearest corner.

We take out the gum from the groove from corner to handle inclusive.

Removing the old handle or what's left of her. If the handle does not come off, pull it down to a corner - the handle will pop out of the groove.

We insert a new handle into the old place, slightly pressing it down from above until it clicks. We check the distance from the edge so that the second handle is set at the same distance from the edge. Metal handle install immediately to the right place, she moves badly, but pull her out out at all problematic.

We insert the elastic into the groove. The elastic near the old handle was a little crumpled. It is in this place that you need to put a new pen. It is very difficult to insert the elastic between the handle and the frame. Do not forget that you can lather it, and then the work will go easier.