Repair of heated seats Renault Logan do it yourself

Seat heating in the base Renault Logan is provided only in the driver's seat. The passenger seats are heated in the Prestige and Privilege trim levels. Unfortunately, the system occasionally malfunctions.

Heated seats are an important element of driver and passenger comfort, especially in our country. It is more difficult for a freezing driver to focus on driving. On the other hand, many owners deliberately refuse this option. For the rest, the possibility of completing with freelance heating is provided.

Under the textile upholstery of Renault chairs there is a canvas with heating wires, they are also called "threads". Structurally, the system consists of a control unit and a backrest sheet.

The current from the battery terminals is supplied to the control unit. From there, it enters the series-connected canvases and backs. Tension arises in the threads, which creates the required temperature. Due to this design, the presence of current in the system is checked from the web contacts: if there is voltage there, then the problem is in the backrest web.

Occasionally the owners consider the normal operation of the system to be a problem. It is equipped with a thermostat that controls how it functions. So, upon reaching a certain temperature, the system automatically turns off. In addition, the heating does not turn on when the outside temperature is above + 7 ° C.

Tip: In the latter case, a frozen water bottle will help to deceive the temperature sensor. If you need to drive, and the system does not turn on due to insufficiently low temperature outside, then the bottle is placed closer to the junction of the seat and backrest, and the heating will start.

Thread breaks also occur. It is necessary to remove the upholstery of the chair and reveal the breaks with a multimeter or visually. The elements of the system are connected in series - when it does not work, you first need to check the contacts, and then the backs. You can fix the problem by connecting the threads, but only as a temporary measure. It is better to replace the cloth with burnt threads. The replacement process is described below.

Another reason for the breakdown is the disconnection of the temperature sensor wire. As already mentioned, it is located on the seat, closer to the back. The problem is widespread - the wires connected to the sensor are too tight. Because of this tension, the wire falls off. You can solder it by removing and unscrewing the casing. In this case, it is better to tighten and fix the wires so that the break does not recur.

In case of problems with the Renault Logan heating system, you must first of all check the fuse. It is located in the mounting block in the salon. The fuse box is located on the side of the dashboard, under the cover. The diagram on the lid will help to determine it.

The fuse is blue (15 A). It is located in the first horizontal row on the left, fourth from the top. The fuse is labeled F16. If everything is in order with him, you can proceed to further inspection. If it burns out, a banal replacement will help.

Some malfunctions, for example, multiple thread breaks, make it impossible to repair the heated seats - you will have to change the entire system. Using the services of a service center or other workshop can be unprofitable financially.

Renault Logan's "native" heating system is hard to find. In addition, there is no guarantee that it will not deteriorate like the previous one. Many car enthusiasts opt for the Emelya domestically produced system. Modifications UK and UK2 differ only in control units.In the first, the control element is made in the form of backlit buttons, in the second - a rotary regulator of the heating intensity.

By purchasing such systems and installing them on Logan yourself, you can save a lot. The price of "Emelya" is an order of magnitude lower than its counterparts from the manufacturer, but it works just as well. With the tools and minimal skills, the installation process will take no more than an hour and a half. In workshops, the standard replacement rate is three standard hours.

To replace the blades, you need to prepare: pliers for removing the retaining rings, plastic ties from any hardware store to replace them, flat and "star" screwdrivers, a hook for pulling ties and double-sided tape, a stationery knife and a replacement heating kit.

For convenience, it is worth dismantling the Logan chairs. A screwdriver or an "asterisk" screwdriver will help to twist the fasteners. Having removed the chair, you can start replacing the canvases:

1. Remove the seat adjustment knobs with a flat screwdriver.
2. Dismantle the plastic sidewalls by unscrewing the bolt on one side, on the other - the plastic retainer.
3. Turn the chair over and remove the retaining rings for the trim from the underside.
4. Remove the trim and open the rings at the back of the seat, at the junction of the backrest and the bottom, and on the sides of the central square.
5. The backrest lining is not fastened with rings, so it can be simply pulled off.
6. Remove old heating elements.
7. Fasten new ones with double-sided tape.
8. Tighten the backrest cover carefully so that no folds form on the heating element.
9. Fasten the center square of the lower part of the seat with plastic ties. For convenience, use the hook prepared earlier.
10. Tighten the upholstery on the bottom of the seat carefully using the same ties to secure it.
11. Connect a new heating kit to the standard control button or replace it with a control unit from a new set.
12. The standard button may not be suitable for the wiring. To install a new control unit, you will have to correct the hole in the plastic case of the sidewalls with a clerical knife.
13. Lay the wires under the plastic "sidewalls" and fix with ties.
14. The replacement is done, it remains to return the chair to its place and connect it to the power supply.

Normal connection of non-standard heating Renault Logan may require replacement of connectors in the car.

Repair of the Logan temperature sensor begins with step 4. By removing the trim on the lower part of the seats, the sensor can be found very close to the backrest. It is enclosed in a round black plastic case the size of a ruble coin. We tighten and solder the disconnected wire. We fix the wires with ties and return the sheathing to its place.

We repair heated seats in Renault Logan on our own, saving a lot of money. The most common breakdown, which is eliminated with a soldering iron and hands growing from the right place)))

We repair heated seats in Renault Logan on our own, saving a lot of money. The most common breakdown, which is eliminated with a soldering iron and hands growing from the right place)))

Removing the seats to remove the bolt corrosion and install the seat covers. Buy plastic pullers https://ali.pub/er5tf Trivia for megan https://ali.pub/4svjl

In winter, I especially want warmth, but not all manufacturers equip cars with heated seats. Do-it-yourself seat heating - we will provide ourselves with comfort.

A video about how you can fix the rear window heating threads. Here I showed some of the nuances and my experience when repairing the rear window heater. This video is not an advertisement of a particular manufacturer, since I was not a professional but an ordinary user and made repairs in a regular garage. After some repairs with cheap preparations of gray color and an incomprehensible composition (I tried several of them), they either did not work, then blurred when the glass was melted. In one of the village auto shops I found this repair kit. At the request of the audience, I write its name (I found a lost packaging) * PERMATEX *. In general, I am satisfied with the drug. I rolled it off for two winters, everything worked. I liked the fact that during the repair, the color of the drug is close to the color of the factory threads (not gray) and it is practically not noticeable during a neat repair.

help please do not start Renault Kangoo 2004 tell me what maybe drowned out the engine everything was fine, after a while I started to start it will not start noticed that the glow coil does not burn diagnostics does not show anything please tell me what could be

Dear subscribers, do not forget to subscribe to the channel and the group on VKontakte Not just a website

Online store "Auto-Gadget" z

How to easily and effectively make the driver's seat in Renault Logan more comfortable

We repair heated seats in Renault Logan on our own, saving a lot of money. The most common breakdown, which is eliminated with a soldering iron and hands growing from the right place)))

We repair heated seats in Renault Logan on our own, saving a lot of money. The most common breakdown, which is eliminated with a soldering iron and hands growing from the right place)))

Online store "Auto-Gadget" z

“Budget, speed and do it yourself” - these are the keywords of the recorded video on various modifications of Renault Sandero or Renault Logan. # Clickoncar20k

We repair heated seats in Renault Logan on our own, saving a lot of money. The most common breakdown, which is eliminated with a soldering iron and hands growing from the right place)))

III Toxa III 3 dias atrás

Please tell me the fuse number

Anvar Gilmutdinov 4 meses atrás

Hi Vitaly! The heating does not work for me, I disassembled and found out that two wires (yellow and black) fell off, the yellow wire knew where to solder, but where the black one did not understand. The black wire is the one that is paired with the yellow

vadim grudin 5 meses atrás

when removing the seat, you need something to disconnect from. where ?

Vika Girnova 11 meses atrás

what is the number of the fuse responsible for seat heating