DIY kyocera printer repair

In detail: do-it-yourself kyocera printer repair from a real master for the site my.housecope.com.

Multifunction device Kuocera can issue error codes to your display in the event of a malfunction. To get your bearings in numbers, we offer you a set of the most common ones:

• E-0007 - you need to install a new toner cartridge because the used unit is used up.
• C 7990 - the waste toner box is full, you need to clean the drum unit.
• C 3100 - it is required to unlock the scanner by moving the latch to the working position.
• F248 - it is difficult for the printer to process the image, since the print job most likely contains special characters, restart the device.
• C 2810 - a problem with the mining motor.
• E-0001 - the device has noticed a non-original toner cartridge, you can reset it by simultaneously pressing Stop / Reset and the button next to the indicators, holding it for 5 seconds.
• 1101 - you need to check if the specified SMTP server or host name is correct.
• C 6000 - there was a failure in the work of the pinning unit.
• CF000 - there is instability or interference in the power supply network.
• J-0511 - remove the jammed paper under the rear cover.
• E-0008 - you need to close the front or back covers.

Kyocera MFP Repair in case of error, it is possible even with your own hands with a careful and careful approach. Study the characteristics and instructions for the Kuoser equipment model, determine the cause of the problem and determine how difficult it is to repair it yourself. If the work requires a professional approach of specialists, then, without hesitation, take the multifunctional device to the service center or call the wizard with a visit to the office or home.

Printers, scanners, multifunction devices - office equipment has become a part of our life: these devices are now available in any office and in almost every home. Like any electronics, such devices, no matter how high-quality they are, can start to "junk" over time. Someone in such cases immediately goes to the service center, someone tries to repair the printer on their own at home, which sometimes leads to disastrous results. Let's find out together in what cases do-it-yourself printer repair is justified, and when it is better to use the services of professionals.

Video (click to play).

Printer interruptions can occur for a variety of reasons. The most common problems faced by users can be described as follows:

Problems with feeding / dispensing, even paper rolling.
Horizontal / vertical stripes appear on sheets.
Loud noise during the operation of the device.
Problems turning on the printer.
"Invisible" cartridge that is not recognized by the printer.
Inability to print from a computer or print "incomprehensible" characters.
Inability to print a given (usually large) volume.

We have listed several problem situations, but in fact, printer malfunctions can manifest themselves in different ways - depending on the type of device, its "age" and other factors.

Let's figure out in which of the cases it is possible to repair printers at home, and whether it is possible in principle.

A strong noise during the operation of the device is most likely caused by a malfunction of the gearbox or the main drive, so you should immediately contact the service center, and not try to "fix" the printer by repeatedly turning it on and off.

There are many sites on the Internet that describe in detail how you can easily and easily repair any equipment with your own hands.However, in our opinion, the repair of printers should be carried out only by specialists who will accurately identify and fix the problem, and will not act with improvised means (screwdrivers, nail files, scissors), as most users would do. "So what happens when you run to the service center at the first unsuccessful attempt to print a sheet of paper?" - you ask. No, you don't need to run right away, you can still do something at home - for example, carry out initial diagnostics of the printer's operation.

Often, oddly enough, the printer does not work for "funny" reasons:

incorrectly installed cartridge,
not exposed sheet limiters,
tray not fully retracted,
foreign objects stuck in the printer.

Therefore, if your machine suddenly starts to jam or tear the paper, make sure that all the elements in it are installed correctly. Remove the cartridge and carefully inspect the inside of the device: if you see the remains of a jammed sheet, it is better not to try to get it yourself using sharp objects, they can cause much more damage.

If water, sand such as plaster, earth from a flowerpot gets inside your printer, or toner spills, unplug the machine immediately and contact the service center.

Another diagnostic trick to understand where the problem lies is to use one cartridge instead of the other. If your printer “does not see” the cartridge, jams the paper under it, prints stripes on the sheet, install another cartridge in it, if, of course, you have one. Restoring the device's performance will indicate that the problem was in the cartridge, but if the problems persist, then the malfunctions should be looked for in the printer itself. By the way, sometimes stripes on the paper indicate that soon you will need to refill the cartridge. When stripes appear on the sheets, take out the cartridge, shake it well several times and put it back in place: if the “streaking” has disappeared, it means that the matter is in the running out of toner.

• E-0001 - the cartridge and toner in the printer are not original.
• E-0003 - the memory is full, a reboot is required.
• E-0007 - the toner cartridge has run out.
• E-0008 - front or back cover is open.
• E-0009 - the tray is full.
• E-0014 — Incorrect paper size.
• E-0015 - the network or USB cable is not connected.
• J-0511 - paper is jammed under the rear cover.

Umedia Service performs post-warranty repair Kyocera printers with free diagnostics in 22 service centers in St. Petersburg and at home! For renovation Kyocera uses only original parts from the manufacturer Kyocera.

Our technicians daily answer a large number of questions about the repair of Kyocera printers. Check out the questions that concern you below, or ask your own question, which we will be happy to answer!

Hello, we poured paints into the Epsom XP-342 printer, when turned on, it gives an error number 000031, what is it? is it possible to own it.

When printing starts, the process is in progress (sound of operation, paper delivery speed), but the sheet comes out white. previously left traces of stripes when printing. Requests: general.

Worked for 5 years without repair. Yesterday refueled with ink - printing stopped

The pick-up roller spins freely, takes a long time, the paper is not pressed or picked up, The red light turns on, the printer turns off (off.

Didn't work for about a year, put new cartridges, copied the color and black-and-white sheets turned out fine, the following sheets became paler.

Hello! After refilling the cartridge of a Canon copier, white sheets of paper come out during copying. What could be the reason?

The cover of the paper feed tray is broken. it is possible to acquire a new one through you. Serial number RC3-2534

The MFP began to display an error: “Printing system failure - printhead not found, damaged or improperly installed”. The service was replaced.

From time to time, printer owners encounter malfunctions.Most people have independently acquired personal experience in eliminating the minor flaws of such a device. As practice shows, a frequent reason for the unwillingness of the printer to work may be a software failure or a minor malfunction in the mechanical part, which can be eliminated independently, without seeking help from a specialist.

Let's consider the probable causes of malfunctions and how to eliminate them on our own, without resorting to the help of another person.

The device of printers such as HP, Canon, Epson, Samsung, Sharp, Ricoh is fundamentally the same. Therefore, we will consider several reasons that are found on all printing devices:

After the printer gave you the information about the error, first of all, check the presence of paper in the loading tray, whether the paper is jammed, the presence of toner in the cartridge, whether all the covers on the printer are well closed and, of course, the connection to the network and to the PC.
A common problem that you may not be shown is a software glitch.
One of the most common malfunctions is contamination of the mechanical parts of the device. First of all, you need to disconnect the printer from the power supply, open the top cover where the cartridge is located, take it out and visually inspect both the cartridge itself and the mechanisms in the field of view. In case of contamination of the mechanism, you just need to wipe it off with cotton napkins, slightly moistened with water. In hard-to-reach places, cotton swabs will come to the rescue.

Important! In no case should you use detergents and liquids containing alcohol.

In addition to all of the above, listen to the operation of your device. Are there any extraneous noises coming from it? If you hear them, this could be a signal that the gears that activate the printing mechanism are out of order. In most cases, they are made of plastic.

Below we will consider how to make repairs using the example of an HP LaserJet 1100 printer. This manual will also be useful for repairing Canon, Samsung and Epson printers.

Suppose the thermal film is damaged during printing with a paper clip on the sheet. For repairs, you need a small set of tools:

crosshead screwdriver;
flat thin screwdriver;
pliers with long jaws;
wet wipes or cotton-dampened pads.

Having prepared the necessary tool, we proceed to repair the device:

Important! During such work, each operation must be carried out very carefully, since the printer is mostly made of plastic and any latch or part can break. Of course, after assembly, there should be no unnecessary parts left.Technical Center. Maintenance of copiers, MFPs, printers. Supply of consumables and equipment. Refueling and restoration of cartridges. Technical support.Has your Kyocera ECOSYS-M2035dn stopped working normally (poor print quality, paper jams, extraneous noise, does not turn on, etc.)?Check for warranty coverage. You should familiarize yourself with the warranty card, which describes your actions in the event of a malfunction of the purchased equipment and the conditions under which warranty repairs will be possible. If the manufacturer's warranty has expired, check whether paid service / repair was performed on this device, as a rule, the service center gives a guarantee for the work performed.Before contacting the service, you should carefully read the operating instructions and the articles specially prepared by us for you, in which some types of malfunctions are spelled out that are self-corrected by the user. This will protect yourself from unnecessary costs.If it was not possible to eliminate the malfunction on your own, fill out an application for consultation. Try to provide as complete information as possible about the problem.Contacting the service center.Technology: Kyocera ECOSYS, Laser.
Control panel display: 5-line LCD display.
Print speed: up to 35 pages per minute A4 (print / copy).
Permission: 1200 dpi (1800 x 600 dpi when printing), 600 x 600 dpi, 256 shades of gray (when scanning / copying).
Peak load: Maximum 20,000 pages per month.
Warm-up time: Up to 20 seconds.
First sheet exit time: Up to 7 seconds.
First copy out time: Approximately 6.9 seconds.
CPU: PowerPC 465S / 667 MHz
Memory: Standard 512 MB, max. 1536 Mb
Power consumption: Print / Copy: 439 W. Ready mode: 65 W. Sleep mode: 3.7W Auto power off mode 0.3W.
Noise Level (ISO 7779): Copy / Print: 49dB (A) half speed mode. Copy / Print: 55dB (A) full speed mode. Standby (ready): 30 dB (A).
Dimensions (WxDxH): 494x430x448 mm.
Weight: about 18 kg.All paper capacities listed are based on a maximum sheet thickness of 0.11mm.Paper feed: 50-sheet multipurpose tray 60-220 gsm, A4, A5, A6, B5, Letter, Legal, Folio, Envelopes, Custom (70 x 148 to 216 x 356 mm) 250-sheet multipurpose cassette 60-120 g / m2, A4, A5, A6, B5, Letter, Legal, Folio, Custom (105 x 148 to 216 x 356 mm). Maximum number of fed sheets with options: 800 sheets.
Duplex module: Standard duplex printing 60-105 gsm.
Automatic document feeder for handling double-sided documents: 50 sheets, simplex scanning 50-120 gsm, duplex scanning 50-110 gsm, A4, A5, B5, Letter, Legal, Custom (140 x 210 to 216 x 356mm).
Output Tray: 150 sheets face down.Standard interface: USB 2.0 (Hi-Speed), USB Host, Fast
Ethernet 10 / 100Base-TX, slot for optional CompactFlash®, slot for optional print server.Functionality: Scan-to-e-mail, Scan-to-FTP (FTP over SSL), Scan-to-SMB, Scan to USB Host, TWAIN (USB), WSD Scan (WIA) (USB).
Scanning speed: 35 ppm (300 dpi, A4, b / w), 14 ppm (300 dpi, A4, color).
Scan Resolution: 600, 400, 300, 200 dpi (256 shades of gray).
Max. scan format: A4, Legal.
Original recognition: Text, photo, text + photo, for OPC.
File types: TIFF, PDF, JPEG, XPS, PDF / A.
Compression method: MMR / JPEG.
Functions: Features: Scan to Email, Scan to FTP (FTP over SSL), Scan to SMB, Scan to USB, TWAIN (USB), WSD (WIA) Scan (USB).Paper Feeder PF-120: Max. 250 sheets, 60-120 gsm, A4, A5, B5, Letter, Legal, Custom (148 x 210 mm to 216 x 297 mm)
Memory expansion: 1024 MB MDDR3-1G memory.
USB IC Card Reader + Card Authentication Unit (B):
Support for various authentication keys.

Additional interfaces
IB-50: 10BaseT / 100BaseTX / 1000BaseT Gigabit Ethernet Network Card.
IB-51: Gigabit Wireless LAN (802.11b / g / n).

CB-120: Wooden stand on wheels with a box for paper.TK-1140 Toner: Ultra clear toner for 7,200 A4 pages. Starter toner resource - 3,600 A4 pages.
Microfine toner according to ISO / IEC 19752.We will repair and service KYOCERA printers, MFPs and copiers with a visit to Moscow 8 (495) 724-64-77. All necessary spare parts are in stock. Refilling of Kyocera cartridges. Warranty for the work performed.The most varied technique Kyocera works in offices including printers and multifunctional devices (MFPs). Of course, like all other equipment, it needs maintenance and timely replacement of resource parts (development units, photo drums, fusing units, rollers, etc.). Less common is the need for repairs such as replacing gears, replacing motors and boards.Along with problems with paper passage, there are also problems associated with print quality.

The device writes “no paper in the tray», «add paper", Less common"add material”Although there is paper in the tray;

The device prints one sheet at a time (jams occur when printing 2 or more sheets);

Paper jams, sometimes accordion crumples;

Paper jams intermittently.

Most of these problems are solved by replacing the paper feed unit or paper feed rollers.

The paper feed unit for Kyocera printers and MFPs consists of three rollers:

Kyocera paper pick roller designed for the initial grip of paper and moving it to the feed roller (most susceptible to wear)
Kyocera paper feed roller is necessary for further transportation of paper to the registration unit - the machine slightly lifts the paper in the tray and feeds it a few centimeters, while the printer beeps and informs about problems with paper.
Kyocera Paper Peel Roller is needed so that the paper passes one sheet at a time - least of all affects the work, but usually worn out more than others.

These faults are typical for printers and MFPs Kyocera FS-1028, FS-1030, FS-1035, FS-2030, FS-2035, ECOSYS M2030dn, ECOSYS M2035dn, ECOSYS M2040dn, ECOSYS M2135dn, ECOSYS ECOSYS M2530dn, ECOSYS M2535dn, ECOSYS M2535dn, ECOSYS M2535dn M3540dn, ECOSYS M2540dn and on other printers and MFPs of Kioser (Kuoser).

The service kit consists of a pick-up roller, a feed roller and a separation roller and is designed for one tray.

The cost of replacing the pick roller, feed roller and separation roller (repair + rollers 3 pcs.) is 2500 rubles.

Hello everyone! After my previous post about repairing printers, I still have +10 subscribers) Although I do not pretend to be such respected pikabushniks as qepka and 80cats (I am far from them and their work profile is different), I am very pleased for your support. In this post I want to tell and show about the repair of some printers that have visited our SC

Xerox WC3220, problem - after turning on it does not go on readiness, a message appears something like “system error: off / on. a printer". I also thought that everything is simple because with the same error, the same printers have already brought, the result - the heating lamp burned out. I noticed that recently they began to bring Sam / Xer printers with a burned out lamp, it seems to be understandable: it often turns on and off during operation (it was just that this was not the case before, and devices of about the same year of manufacture ¯_ (ツ) _ / ¯ ) During the repair process, it turned out that the lamp and the fuses were intact, and the reason was not a contact in the thermo unit connection socket:

Looks like the face of a robot with square eyes) The “teeth” of the robot are the contacts of the thermal sensor, the “eyes” are the contacts of the lamp. Two pins were just a little covered with oxides, I was too lazy to clean them and I put the whole socket from another disassembled thermo unit.

Next, the Canon LBP3110 printer, the problem is crackling when printing, jams. And here is a typical problem - wear of the drive gear of the thermal unit:

In the photo, another printer seems to be Canon MF5730, exactly the same gear in HP 1000/1200/1300 printers and many others

Instead of teeth, the gear has thin plates, of course, there is no normal engagement with the gear of the rubber shaft of the thermal assembly. I think there are several reasons for this wear: different gear material, weak pressure between the gears, wear of the thermal assembly, and the manufacturer himself is not interested in the nodes to serve for a long time

Kyocera ES 1370N printer. Customer complaint that the sheet comes out of the printer by about 2-3 cm and stops. This happens in about 5-15 sheets.

I found out that the Teflon shaft was worn straight to the metal on one edge, but after replacing it, the malfunction remained. Having crawled through the forums on this problem, I realized that either the optocoupler for the passage of paper in the thermal unit is faulty, or the forward / backward rotation switch of the output shaft is damaged (with double-sided printing). I checked all this - the problem remained. Further, suspicion fell on the registration clutch in the gearbox. It is a pity that then I did not take enough pictures because my hands were constantly greased from gears (there is a mechanism that is not easy to disassemble)

Further repair of НР Р2035. They printed until the last: after the thermal film broke, the rubber shaft broke, they stopped only when the printer began to jam the paper, the result: repairs for something about 3000 rubles, and it could be more if the heating element burned out (gray strip on photo) The photo shows that even the paper turned black from the temperature

If you open the rear door of the printer after a paper jam and notice such pieces of rubber roller or thermal film (sometimes they fall into the tray or at the exit from the printer), then turn off the printer and carry it to repair so that you will not spend even more on repairs.

Often, in HP / Canon printers, it is necessary to replace the bearings (bushing) of the rubber shaft of the fuser unit. They are made of heat-resistant plastic, in shape they can be left and right as half rings or one half ring, and the other on the gear side of the rubber shaft with a loop from scrolling in place.

Ball bearings familiar to many are also put into printers, but the price of such devices is usually several times higher. In the upper right corner of the photo, it broke when trying to get it - it was completely erased.Often they wear out unevenly, in which case a skew arises and the thermal film slides towards the worn one and over time its edge breaks. Also, when they wear out, the clamp between the rubbers. the roller and the heating element becomes smaller, which is why the toner does not adhere well to the sheet (the image is erased if you slide your finger over it). On the left side of the photo are two red bearings from canon 3110/3220/5730 and similar. The trick is that the one that is higher in our country is around 200 rubles, and with a loop it is already almost 900 rubles. (!) The wholesale price will certainly be lower, but still I do not understand what exactly is its high price, can any of the pikabushniks know?

The next Brother 7xxx series printer seems to be and the most common problem is poor print quality. It happens that a client calls and asks: "Why is my printer doing there?" Well, I don't like these printers, my parents have a DCP-7030R at home, my father rarely prints and all the rules, and in an organization where you need to print a lot, they constantly bring them with poor print quality. When I just started working in the service I tried to somehow fix the cartridge, clean it there, replace the photo tube, sometimes it seems to help, but more often, or when checking, it will do the same thing again, or then a dissatisfied client will bring it again. The most reliable thing is to buy a new cartridge stupidly and not to steam. Moreover, the compatible cartridge is not much worse than the original, and the price is 3 times less

The cartridge itself consists of two parts: a toner cartridge (TN) and a photo cartridge (Drum). In the photo there is a disassembled Drum without a photo box. In general, cartridges themselves are consumables and manufacturers try to make them disposable in their own way, because this is just a gold mine for them. Someone, for example, puts chips with protection, which are blocked after printing a certain number of sheets, and Brother uses a mechanism instead of chips, which, in principle, is easy to reset to 0, in addition, they took some parts from the printer into the cartridge and made it as disposable as possible ... On average, 4-5 refills and the toner cartridge starts to crumble, and then the dram starts to print badly. As I said before, cleaning and repairing the cartridge does not always help. You can clean the toner cartridge (completely empty out the old toner, invigorate the seals, clean the magnetic roller, metering and cutting blade), but with the drum it is more difficult. As we understood, charge leakage begins and that's it.

Next comes the HP M400 printer - another example of how a manufacturer strives for disposable cartridges. Customer complaint: the printer breaks the teeth of the drive coupling for rotation of the photo roll (by the way, the cartridges are original)

Fortunately, the clutch is available, and it can be removed from the decommissioned ones. The trick is that on previous models with the same fotoval drive unit, such garbage was not observed. If you pull out / insert the cartridge, the printer starts to rotate the shafts, but sometimes the clutch slips and over time the clutch breaks. I had to work on a collective farm with a gear cover so that the clamping of the clutch and the drives was tighter)

True, then, after about 3-4 months, the client brought it again with the same trouble (and they print a lot). There are no further kolkhoz photos - another person took up the printer. In addition to this jamb, the printer has a dull touch display and log firewood - you wait almost an hour for installation, it reaches 99% and an error occurs that the installation takes too long, restart the computer (if there is firewood installed on the same printer, remove them completely and start the installation again)

Further on the list of MFP Toshiba e18. Quite a popular model with a reasonable price for an A3 paper machine. The client says he is jamming the paper in the fuser with an accordion. The client is to blame for this - when a jam occurs, the paper must be removed carefully, otherwise the seats of the paper separator fingers can be easily broken:

You can, of course, try to fix it with a thin drill, wire or paper clips (if you glue something, then with a special high-temperature glue, which we do not have 🙂), but in such cases we usually suggest replacing the entire lid of the thermo unit, there is no other way. If the printer displays a message about the need for service (after about 75 thousand pages) and the print quality suits you, the error can be easily reset, but still sometimes you look inside to see if everything is okay with it. By the way, I recently screwed up a lot with another Toshiba) I replaced the Teflon shaft, began to assemble it back, and at the stage of tightening the fastening screws of one of the heating lamps pulled my hand that broke the tip with the contact of the lamp (I'm a fool, I'm used to using an electric screwdriver, but it was necessary to tighten the usual one carefully) Naturally, there is no way to repair it, and the lamps removed from the old devices have disappeared somewhere. Fortunately, the boss did not swear much, advised him to look into the thermo unit of the old decommissioned model of Toshiba, which had been standing in the corner for a long time. I was lucky - although there was only one lamp, instead of two in the 18th one, it matched the parameters of the broken one.

That's all for today, I think it's time to finish) Why didn't I have inkjet printers in my post? There was a time when our service refused to repair them altogether. there was little exhaust from them. Recently, they decided to take them again, but only to eliminate problems not related to print quality - this is a dirty business, and there is no guarantee of work (at most, start cleaning the nozzles). Usually we reset errors, remove jams, change pick rollers, “diapers” and so on. Instead of cats at the end - fsh with Pikabu from which I blasted out loudly at work: Mitka Makkonokhov and Zhorik Letov

What I liked while working in the SC was the repair of printers / copiers. Although I started with a banal PC repair, then laptops, navigators, etc. As a result, I slowed down on the printer equipment, and for the last three years I have only been repairing it. Now I will explain a little to those who do not know:

1. It is much more interesting (and even more difficult) to repair a printer than computers and laptops (it’s not just me about laptop BGA soldering, etc. a child can handle soldering at a thermal soldering station).

2. Variety of breakdowns, each printer is something new and a drop of experience. Yes, there are repetitive repairs, but their percentage is not as large as when repairing PCs / laptops. There are instances (immediately the cold ran through the body) with which you f * ck for several days and knowing exactly the node in which the malfunction (from personal experience - SHARP, I picked it up for three days, as a result - on the gear already when measuring the gear it turned out that the teeth were licked evenly by 1 - 1.5 mm.) For 10 years of work experience in the SC, I have not yet seen a single laptop and PC which would take more than 2-3 hours to diagnose.

3. Each printer is endowed with a magical mind. And if you do not say at the end of the assembly and before the test check the phrase: “Well, bitch, just try to fuck, I won’t fucking disassemble you for the third time” - then there is a possibility that I didn’t finish something. The most important thing is communication with the printer, you have to feel it so to speak. ~~(to know in which case in which area to get off the feet)~~.

4. Incredible thrill when everything works. Especially the buzz is obtained from the repair of the mechanical part (~~there is the fiercest pi * ets just~~).

5. Copiers (these are such big infernal office machines) are the raisins for an employee of the SC. Since this is the same printer, only there are more details - ask where are the raisins? For the price of repair, they are charged 10 times more expensive.

And finally, I would like to end with the following phrase: you can't just pick up and assemble so as not to leave extra bolts.

The device of laser printers and MFPs KYOCERA.

The main components of the MFP.

Main shafts.Passing the paper from the tray to the registration shaft, then transferring the image to it and then passing through the oven where the image is fixed by a high temperature with a pressure roller (rubber) and thermal film (or Teflon roller)

The paper sensors are checked when a paper jam is indicated. Check by removing the cartridge for jammed paper, pieces of paper, or foreign objects on the sensors shown

Paper picking problems from the lower tray are due to dirty or worn roller

A paper jam at the exit from the device is caused by a rupture or wear of the thermal film (for a Teflon roll, dirt or abrasion of the surface)

Printouts have gaps or random dots. The reason is the development unit and the AMD MFP of the KYOCERA printer.

Tekhorgservice specialists carry out work on the repair and refueling of the KYOCERA printer MFP. :

Replacing consumables for the MFP of the KYOCERA printer (improper operation and failure to perform preventive maintenance on the MFP of the KYOCERA printer).

For each MFP KYOCERA printer, there are calculation tables for the planned replacement of elements according to the passage of their resource (number of copies). To ensure reliable operation of the MFP of the KYOCERA printer, replacement is carried out within strictly established terms of operation.

In the event of a malfunction of the KYOCERA printer MFP, it is replaced with a new item according to the catalog number for an original or compatible spare part.

The most complex repair requiring a highly qualified specialist is the appropriate element base and equipment for monitoring the performance of the KYOCERA MFP printer. In the event of a failure of an electronic component developed by the manufacturer for a specific model, the entire unit has to be changed, which sharply affects the timing and cost of repair and is not always justified in ensuring the restoration of the functioning of the KYOCERA MFP.

An experienced specialist will find, repair or replace a faulty element of a KYOCERA MFP. Whenever possible, when ordering repair, try to clearly describe the problem and fix the KYOCERA MFP, this will reduce the repair time and cost.

All types of repair operations for the MFP of the KYOCERA printer are carried out by agreement with the customer at a convenient time for him, confirmed by an act of work performed and paid as the repair is completed.

Printer won't turn on? Is your computer unable to see the device, or is the printer printing dirty paper? We specialize in field repair of Kyocera laser printers in Moscow - at a convenient time for you, our specialist will come to your home / office and quickly carry out the necessary repairs of any complexity.

We do not repair A4 inkjet printers and scanners. in most cases, repairing such printers is impractical. Also, we are not engaged in refilling cartridges. Also, if you have disassembled equipment, then we will not be able to accept such a device for repair.

To make the repair of Kyocera printers take the minimum time, when calling our specialist, describe in detail what exactly is happening with the device, tell us the brand and model. So the master will be able to pick up the necessary parts before leaving.

The exact cost of repairs is reported to you only by a specialist after inspection and determination of the complexity of the required work. If the repair of Kyocera printers turns out to be impractical, the wizard will definitely warn you about this before starting work.

The prices presented on the website are not final and may vary up or down. We provide a long-term guarantee for all services.

Our craftsmen work in all districts of Moscow and the nearest Moscow region. To complete your application, just call 495 662-99-64.

In recent years, modern office equipment has closely entered our daily life, solving many issues related to maintaining important documentation, sending, copying all kinds of electronic and paper media.

It is good when all our electronic assistants are in good working order and faithfully work for our good. But there are situations when technology fails, then we truly understand the importance of these electronic devices.

The Printmaster company carries out repair of Kyocera printers and has sufficient experience in this direction. We have a professional, close-knit team of like-minded people, a large, modern repair and diagnostic base. We carry out even the most complex repair work on any type of equipment.

It is not so rare that incompetent, unprepared people undertake repairs to printers, which leads to new, even more serious damage to the device. In this case, the cost of repairs may increase due to outside interference. It happened that after such would-be specialists the equipment became unrepairable.

In addition to the repair of Kyocera printers, our company is engaged in comprehensive preventive maintenance of equipment and office equipment of our customers. As you know, it is better to prevent the disease than to cure it for a long time.

For a more complete understanding of the algorithm of actions of our employees and customers who have contacted us, we present step-by-step operations after the Kyocera printer came to us for repair:

- the very first step in this process is a comprehensive diagnostics of the Kyocera printer, which includes the identification of faulty electronic components of the device's circuit or its entire blocks. After the printer falls, all sorts of mechanical damage to both the external case of the device and its internal filling, including cracks in the printed circuit board, are possible;
- after carrying out the diagnostics, our specialist will analyze the possible cost of repairing the Kyocera printer and its timing. It often happens when the cost of repairing or restoring a printer is financially comparable to the cost of a new device or even exceeds it. It is clear that in this case the repair itself is not economically feasible;
- in case of a positive opinion of our specialist about the profitability of further repair or restoration of the printer, the nuances of the repair time and its approximate cost are negotiated with the client. If the client agrees with our terms, then the printer is handed over to the technicians for repair;
- directly repair the printer itself, with the replacement of failed radio components or entire units of the device.

There are a lot of firms and companies for the repair of office equipment, printers in particular, in our time. It is simply impossible for an uninitiated person to understand this abundance of proposals, but it is worth asking these people a few leading questions, everything immediately becomes clear. For example, many firms refuse a full-fledged warranty period, citing all sorts of pretexts.

The Printmaster company is completely open and transparent for our clients and immediately stipulates all possible nuances. So our arguments are:

- the pricing policy is based on the minimum principle, i.e. prices are always the lowest in their segment;
- highly qualified and competent personnel;
- the possibility of temporary substitution of the printer for our client;
- departure of employees to the customer's territory;
- using only original electronic components and spare parts during repair work;
- the shortest terms of the repair;
- full warranty service.

Need urgent repair of a printer or MFP Kyocera, Ricoh, HP, Konica Minolta?

Apply now:

e-mail: This e-mail address is being protected from spambots. You need JavaScript enabled to view it.

Our service center engineers repair Kyocera, Ricoh, HP mfp and printers in Moscow and the Moscow region, directly at the customer's place.

At the end of the work, the engineer provides an act of completion, an invoice and an invoice.

Diagnostics of A4 color duplicating equipment is carried out by prepayment or by a letter of guarantee signed and stamped by the manager, followed by payment of the invoice for diagnostics.

If it is necessary to replace parts, the service center will issue an additional invoice for the parts required for repair.

In difficult cases, printing equipment is delivered to the hospital, where detailed diagnostics and repairs are performed.

We work only with legal entities. We conclude contracts for scheduled maintenance of equipment.

In order for the engineer to be able to leave for the repair of your printer or MFP, we need the following data: the name of your organization, TIN / KPP, actual and legal addresses, contact person and his phone number, equipment model and problems encountered. This data must be sent to the email address This email address is being protected from spambots. You need JavaScript enabled to view it. or fill out the form above. The service manager will contact you and specify the time of arrival of the engineer. Service center phone number +7 (495) 727-02-01. Call us, we will be happy to answer your questions.

The cost of leaving within the Moscow orbit is 500 rubles, outside the Moscow orbital (up to 25 km) - 1000 rubles, (from 25 to 70 km) - 2000 rubles.

Under this contract, maintenance (technical maintenance of printing equipment) is carried out monthly (quarterly). Spare parts, toner, sold separately. Recommended for light duty vehicles.

Departure and diagnostics - free of charge;

Guaranteed availability in our warehouse of routine spare parts at a fixed price for the equipment included in the contract;

A database is maintained on the work performed, which reduces the time for diagnostics and troubleshooting.

Under this agreement, payment is made for the prints produced on your equipment. The price of a print includes maintenance parts, toner, and the work of an engineer. Work on the equipment is carried out at intervals in accordance with the service documentation. Recommended for heavy duty vehicles.

Transparency - there are no additional fees;

Reduction of repair time - maintenance, replacement of maintenance parts, delivery of toner is carried out without delay during the period of the contract, it is possible to provide replacement equipment if it is impossible to repair promptly, billing for maintenance - at the end of the reporting period;

Predictability of payments - you can predict the amount of costs under the planned load;

Direct interest of our company in the performance of your equipment.

Under this agreement, payment is made for prints made on the equipment provided for rent. The price of the print includes depreciation of the equipment, all parts, toner, and the work of an engineer. Work on the equipment is carried out at intervals in accordance with the service documentation.

There are no investments in the purchase of equipment, the equipment is on the balance sheet of our company, the equipment is out of order and worn out;

Transparency - there are no additional fees;

Reduction of repair time - maintenance, replacement of maintenance parts, delivery of toner is carried out without delay during the period of the contract, and billing for maintenance - at the end of the reporting period;

Predictability of payments - you can predict the amount of costs under the planned load;

Direct interest of our company in the performance of the equipment provided for rent.

We offer for rent office printing equipment from 35 ppm A3 format on a lease basis. In this case, payment is made monthly, depending on the number of printed pages, or fixed per unit of equipment. Our company fully undertakes the provision of office printing equipment, consumables, as well as service. As the service life of the client's equipment develops, we replace the used equipment with our own.The cost of consumables, spare parts and service is included in the price of a print (from 0.15 to 1.5 rubles, depending on the equipment and the volume of monthly printing).

List of required documents:

1. Application for the required equipment.
2. Notarized copies of constituent documents (Articles of Association, Memorandum of Association, decision on registration, amendments to constituent documents, STI certificate of amendments to the Unified State Register of Legal Entities).
3. Copies of documents confirming the powers of officials entitled to sign official documents (general director, chief accountant, etc.).
4. Balance sheet for the last 5 reporting periods, including the profit and loss statement (Form 2 balance sheet) with the mark of the tax office.
5. Statement of cash flow on the current account in the servicing bank (banks) for the last half of the year, broken down by month (certified by the bank).
6. Certificate of ownership or lease agreement for the premises where the leased equipment will be located.

Video (click to play).

Order: This email address is being protected from spambots. You need JavaScript enabled to view it.

Rate the article:

Grade 3.2 who voted: 85

DIY kyocera printer repair

Printouts have gaps or random dots. The reason is the development unit and the AMD MFP of the KYOCERA printer.

Replacing consumables for the MFP of the KYOCERA printer (improper operation and failure to perform preventive maintenance on the MFP of the KYOCERA printer).

For each MFP KYOCERA printer, there are calculation tables for the planned replacement of elements according to the passage of their resource (number of copies). To ensure reliable operation of the MFP of the KYOCERA printer, replacement is carried out within strictly established terms of operation.

In the event of a malfunction of the KYOCERA printer MFP, it is replaced with a new item according to the catalog number for an original or compatible spare part.

An experienced specialist will find, repair or replace a faulty element of a KYOCERA MFP. Whenever possible, when ordering repair, try to clearly describe the problem and fix the KYOCERA MFP, this will reduce the repair time and cost.

Popular

Car wash calm do-it-yourself repair

Jackhammer Makita DIY repair

Do-it-yourself repair of deep scratches on a car

DIY niva 2121 bumper repair

New items

DIY d4bh pump repair

Steering rack Renault Logan with gur DIY repair

Do-it-yourself KamAZ fuel equipment repair

DIY tile roof repair