In detail: do-it-yourself ps one repair from a real master for the site my.housecope.com.
Need help repairing PS ONe game consoles. PS ONE has no picture or sound. I insert the disk, everything seems to be spinning normally. Checked voltages, all fuses are good. Please tell me where to start diagnosing the problem. If possible, describe on the forum a step-by-step method for diagnosing a malfunction. I will be grateful for help.
In the “Encyclopedia of Repair” there is info on prefixes.
a guest, you need to wave harder, then you will learn to fly 
To begin with, check whether the disk actually rotates in the set-top box when the case is removed.
Further, if your disk does not rotate, then the CXD 8606 central processor most likely failed, but if it rotates, then most likely either the AV cable connection port is faulty, or the reason is much more complicated:
1) malfunction of the A2106R chip (imaging);
2) the most likely reason is no + 5V from the 78M05 chip;
3) failure of the output stage microcircuit.
Will you help me?
When you play games, black squares flash and all sorts of stripes where you don't need them. tell me what is the problem?
If at all games absolutely, then Khan.
often ask for a pressure plate for the Sony Ps1 CD drive. Tell me where you can buy them (especially in Ukraine). Thank you
somewhere, I don't know
there was some advice here
take from old cd roma
for some, it is attached to the outer case - cut a larger circle
and for some, to the insides, break off from the body and attach to the cover sp1
at the old sidirom exactly cut out a circle, more than there in the inside
and at the inner edge
 |
Video (click to play). |
Attaching is no longer a problem.
In PS1, the disk is loaded but does not respond to the joystick. Advice is required.
If you have a PS one, then first check all the fuses for power, you can start with the most positive contact on one of the joystick ports, if power is supplied, then next to the second port there is a small gray light-colored diode, ring it, and to be sure, you can even soldering, it is not necessary to work, if without it the arrow of the joystick appears in the main BIOS menu, then everything is ok, but the diode is mostly on when someone incorrectly solder the wires to the joystick or the Chinese joystick burns out.
If you have a large model, then ring the fuses, with the exception of the fifth series model, diodes can also fail there.
RADIO magazine 2003 6 number p. 22 PS one operation and repair 
Problem! Joysticks work if you insert a regular audio disc, as soon as you insert a game disc, the joysticks do not work. who faced what is the problem help.
people, but did not meet with such a problem. Some games restart out of the blue. some in certain places. i dont know what to think
for Areon and UNIT, it is good to warm up the CPU and memory with the station. In 99% everything starts working.
This little spinning round thing that spins discs in SonyPS had three silvery little balls. I suffered nonsense, pulled them out and lost them. The disks don't want to spin anymore. Sometimes, grunting, spinning. More often not. Games are not loading. What to do?
Catherine_Elizabeth, 
I advise you to search and paste in place. These are disk holders.
I inserted these three balls
but as soon as the disk starts spinning, the balls are shot in different directions
Catherine_Elizabeth, So you broke and the latches from which the springs also fell down.
Look for workshops where they can help you with this problem.
The spindle needs to be replaced.
Give a link to the repair encyclopedia
And then I click on the link, and they return me to the same page
In general, I repaired Sonya, everything seems to be fine, but I didn’t like the work of the SD-ROM, I pressed it on the spindle, the image and sound disappeared, one of the mikruhs began to warm up, disassembled, assembled, powered on, the disk loads, but there is still no sound and image . What to do?
hello dear, help me eat a sony ps one after a power surge does not turn on. bp works scheme is where to dig please tell me
Guys problem. The motor does not spin! The motor is 100% working, tested by the power supply. Where to dig??
Design and support:
Aleksandr Kuznetsov
Technical support: Mikhail Bulakh
Programming: Danil Monchukin
Marketing: Tatyana Anastasyeva
Translation: Natalia Kuznetsova
When using site materials, a link to https://my.housecope.com/wp-content/uploads/ext/3265 is required
made in Ukraine
PS one: operation and repair
The video game console “PS one” by the Japanese company Sony is the result of the development of a series of consoles “PlayStation” [1]. The small weight and the sizes leave an imprint on features of its operation. Compared to previously released models, “PS one” suffers from accidental falls from a height more often, you can literally sit on it without noticing on a chair or on a sofa. As a result, it is necessary to seal cracks in the fragile body of the attachment more often.
To protect your “PS one” and its accessories (joysticks, memory cards) from premature failure, make it a rule not to dock or unpair the connectors when the green indicator on the front panel of the set-top box is lit. And if you really had to do this without turning off the power, apply force strictly perpendicular to the plane of the set-top box. This ensures that the longer than the rest pins of the power circuits and the common wire in the connector will be connected first or disconnected last.
There are no very hot elements in “PS one” and it can be left on for a long time. The network adapter, which continues to work even after the set-top box itself is turned off, is designed for long-term “idle” operation. Nevertheless, it is better not to leave it unattended and unplug it from the wall outlet at night or when leaving home.
The case of the network adapter of the video set-top box is plastic and. non-separable, to resist the age-old childish desire to look, “what's inside?”. By the way, in various household equipment, a similar design is increasingly being used. To gain access to the adapter board, carefully cut its case with a thin hacksaw from the side along the perimeter. After completing the repair, glue the body halves or simply wrap them with several layers of adhesive tape, preferably transparent.
In the network adapter, the 2 A fusible link F1 most often burns out ([2], Fig. 5). Often this is a consequence of a breakdown of a powerful field-effect transistor Q1, which is easy to replace with one of the similar switching power supplies for TVs (FS5TM, 2SK1117, 2SK2666, 2SC2128, 2SC2125, 2SC2718). The transistor must be rated for a voltage of more than 600 V and a direct current of at least 5 A.
The transistors used as Q2, Q3, Q51 are produced by many Western and Asian firms. If necessary, they are replaced by any low-power ones of the appropriate structure (p-n-p or n-p-n) and sizes, for example, the KT3129, KT3130, KT315, KT361 series.
The closest in parameters to the one installed in the adapter (IC1 chip) is the NCP1200D60R2 SHI controller from ON Semiconductor. Optocoupler IC2 - any with an isolation voltage of more than 500 V (NEC2561, TLP621, TLP521, PC817A, “3171”, “3131”). Diodes D3, D4 - 1 N4148 or series KD521, KD522, KD503.
In case of complex malfunctions, it is advisable to refuse to repair the adapter and replace it with any, even home-made and not necessarily a switching power supply with an output voltage of 7.4. 8 V at a load current of 1.5. 2 A. A lower voltage is not enough for stable operation of the set-top box, with a higher voltage, some of its elements will heat up too much: the integral stabilizer IC601, the Q602 transistor ([2], Fig. 4), the IC722 microcircuit (Fig. 3 ibid.).
The appearance of the processor board is shown in fig. one.
All the important elements are marked here. If there are no obviously damaged parts, for example, blackened resistors, on the board, regardless of the nature of the manifestation of the defect, all fuse-links in the design for surface mounting are subject to priority checks (Table 1).In good condition, the resistance of any of them does not exceed several tens of milliohms, a larger value indicates partial or complete operation (burnout).
If the failure was the result of a surge in the supply voltage or an accidental short circuit in the joystick, replacing the burnt insert with a similar one or simply with a piece of wire with a diameter of 0.1 mm usually completely restores the operability of the IVP. Nevertheless, after repair, it is recommended to observe for some time whether the malfunction recurs and whether there are unusually hot parts on the board.
Quite often, protective zener diodes installed in the input and output circuits of the set-top box at the CN502 connectors fail (their failure leads to a lack of image and sound) or CN101, CN102 (joysticks and memory cards do not work). For example, if the stabilization voltage of the zener diode D104 drops to 1.8 V n as a result of a malfunction,
Some joysticks continued to work, while others did not. Zener diodes can be replaced with conventional KS147. KS168 with any letter indices, although it is better to use special clamping diodes [3]. Less often, breaks in the windings of inductors and noise suppression filters occur, which should also be checked with an ohmmeter.
Mechanical damage to the processor board and its elements is not typical for “PS one”, although there have been cases of a short-term loss of power supply due to poor contact in the J001 connector. Sometimes the prefix cannot be turned on because the contacts of the S001 switch are oxidized or burnt. Greater reliability of the switch can be achieved by connecting a free group of its contacts in parallel with the operating one. A break in the hinged conductor going to the IC801 chip once led to the fact that when any game disc was installed in the console, a music menu appeared on the screen.
Table 1 will help you choose a replacement for failed transistors (including those installed in the network adapter). 2. It contains not only the main parameters of each transistor, but also the marking applied to its case, without knowing which, it is quite difficult to “recognize” the device.
Video set-top box resistors are marked, as a rule, in a standard way. Of the three or four digits of the code, the one on the far right is the exponent of the number 10, by which the number indicated by the previous two or three digits should be multiplied. Examples:
However, Bourns resistors are also installed with a tolerance of ± 1% from the nominal value and alphanumeric marking. To decipher the digital part of the code applied to a similar resistor, refer to Table. 3. The number found in it is multiplied by the coefficient indicated by the letter: S - 0.01, R - 0.1, A - 1, B - 10, C - 100, D - 1000, E - 10000, F - 100000. The result obtained is the resistance of the resistor in ohms. For example, 12C - 13 kOhm, 18V - 1.5 kOhm.
The weak point of all "PlayStation" models, including "PS one", is the mechanics of the CD-ROM drive. Long-term daily operation of the attachment leads, as a rule, to the backlash of the rotor of the engine that rotates the disk. Externally, the defect manifests itself in the fact that in the normal (horizontal) position of the IVP case, game programs begin to work only after repeated “fidgeting” of the laser head over the disk. By tilting the case by 10.45°, data entry reliability can be restored. Sometimes the angle required for this stabilizes over time, but more often it gradually increases.
Having found such a defect, first of all make sure that it is in the motor that rotates the disk, and not, for example, in the drive of the optical head carriage. The worm gear of the drive is worn out, sometimes its action is hampered by accumulated dirt. Wash all transmission parts with pure ethyl alcohol and lubricate with vaseline or a special non-thickening lubricant for plastic parts (MOLITUBE, LUBRIPLATE, etc.).
To eliminate the "jerks" of the carriage, sometimes it is enough to slightly shift the motor that rotates the worm, or to put a drop of lubricating oil on its rotor.With a working drive, the movement of the carriage should not be accompanied by crackling and other sounds.
Unreliable data reading may be due to contamination of the optical head lens. This is often caused by the deposition of tar from tobacco smoke on it. The lens surface is blown with dust-free compressed air from a special, similar to an aerosol can, or gently wiped with a clean, dry cotton cloth. It is permissible to replace the lens with a similar diameter of 5 mm from a computer CD-ROM drive.
Sometimes it is useful to increase the power emitted by the laser diode by reducing the resistance of the trimmer resistor located on the flexible cable of the optical head by 10.20%. Before adjusting, measure the set resistance value (approximately 1.2 kΩ) so that in case of failure, return everything back.
If no improvement has come as a result of the measures taken, the most reliable and fastest way to repair is to replace the entire CD-ROM drive assembly with a known good one. In addition to the regular one, you can use the KSM-440ACM drive from the set-top boxes of the SCPH-100 x series. Drives KSM-440ADM, KSM-440AEM differ from other models of "PlayStation" in the length of the flexible cable and design, although they are electrically compatible with "PS one".
Please note that the cost of this operation will be 35.50% of the total cost of "PS one". A cheaper option is to replace only the CD-ROM drive motor. Suitable RF-300PA-11400 D/V 5.9 or RF-300F-11420 D/V 5.9 from Mabuchi.
In a hopeless situation, you can go for an independent engine repair. It, together with a plastic nozzle 2, is schematically shown in Fig. 2. The latter must be removed, having previously measured and recorded the width of the gap S between it and the engine housing 1. This will allow you to return the part exactly to its original place. Please note that the assembly is not designed for disassembly and reassembly, the operation is far from always successful and requires certain skills.
The nozzle is very fragile and is tightly seated on shaft 3. When removing it, it must not be skewed, which can lead to irreversible consequences: bending of the shaft, cracks in the nozzle or a “broken” mounting hole, which does not allow further fixing it on the shaft.
It is best to make a special puller - a lever with two blades that are inserted into the gap. With its help, the nozzle is gently shifted, applying efforts evenly from all sides. This operation can be performed in another way, for example, with the help of several steel plates inserted into the gap from different sides. The main thing is to act carefully and without haste.
Rinse the entire surface of the shaft freed from the nozzle with ethyl alcohol. Then, wearing protective gloves, with a drop of cyacrine (this strong, quick-drying glue is sold under the trademarks “Instant Super Glue”, “Second”), fix the shaft in the plain bearing 4, eliminating play. After a few minutes required for the glue to dry, the nozzle 2 can be installed on the shaft 3, making sure that the width of the gap S is exactly equal to that measured before the start of the repair. If the nozzle slips on the shaft, try to fix it with the same glue.
After a day, you can begin to “train” the engine with a voltage increased to 8.9 V. At the first start-up, the shaft will accelerate slowly, as if with difficulty. After a few "training" normal rotation will be restored.
Cyacrine is able to firmly glue biological tissues, so it should be used with caution, avoiding contact with the skin.
- Ryumik S. "PlayStation": history of development. - Radio, 2002, No. 11, p. 21, 22.
- Ryumik S. “PS one”: schematic diagram. - Radio, 2003, No. 1, p. 23-28.
- Semiconductor voltage limiters. - Radio, 2002, No. 8, p. 50 - 52.
See other articles section Television.
Vladimir
The worm gear gears broke, I ordered a new laser unit for aliexpress.I installed it and when the set-top box is turned on, it makes a sound like when the motor is running (there is a feeling that the motor is spinning), and it does not stop until you turn off the power, but the landing slot for the disk does not spin. As if the spindle with the rotor lost contact. Please tell me how to solve the problem.
SnakeR 
User
Posts: 44
Registered: 04/10/2012
Rating: 0
cybdyn
Veteran
Posts: 1365
Registered: 12/20/2011
Rating: 8
under the plug where 4 wires come to a scarf with a small motor. immediately below the connector, the nearest soldering pad is “+” or for the red wire, the bottom one is for the black “-” minus.
It's also a good idea to check the fuses.
SnakeR
User
Posts: 44
Registered: 04/10/2012
Rating: 0
cybdyn
Veteran
Posts: 1365
Registered: 12/20/2011
Rating: 8
SnakeR
User
Posts: 44
Registered: 04/10/2012
Rating: 0
cybdyn
Veteran
Posts: 1365
Registered: 12/20/2011
Rating: 8
on the left edge of the board in the middle on the old wide boards 4 pcs, they say “20”, on the last 3 pcs. they are smaller.
it just suddenly turns out that the motor is soldered and it does not turn, then it’s more likely that there is no voltage on the driver’s power supply, just a predhr.
and the motor was torn out, I probably decided with a backlash and I didn’t read the disks well, - replacing the motor or lubricate
SnakeR
User
Posts: 44
Registered: 04/10/2012
Rating: 0
SnakeR
User
Posts: 44
Registered: 04/10/2012
Rating: 0
cybdyn
Veteran
Posts: 1365
Registered: 12/20/2011
Rating: 8
SnakeR
User
Posts: 44
Registered: 04/10/2012
Rating: 0
cybdyn
Veteran
Posts: 1365
Registered: 12/20/2011
Rating: 8
which block is native or similar?
check the voltage from it. and whether it reaches the plate.
check the soldering of the yellow connector where you insert the block
check voltage after fuse ps000
check fuses, others PS00X
check for a short circuit between the ground and the output of the coil (blue barrel, the upper left edge of the board), if it is short-circuited by a khan or some kind of big mikruha.
if it doesn’t short and there is no voltage, then the transistor-key could fly out, next to the right of the coil
if there is a power supply - but the black screen is still a khan to the processor or the memory chip.
All other questions that are not related to the topic are deleted.
Please, in case of a problem, describe the problem in detail, in intelligible Russian.
Is it possible to replace the 5.9 volt spindle with a 3 volt one?
you can replace it, only how long it will work is unknown, if at all it will work for some time.
it all depends on the winding, if it is designed for such a voltage, it will work, if not, then there will be overheating, and in the future the winding will burn out, it’s good if there is no short circuit.
gayal, I removed such motors from old PCs of SD drives, they carry a sled, they are designed for high voltage.
I have one in ZYCH, I replaced it myself, only the fuss will be with this thing for disks, it must be installed accurately enough on the spindle, at the right height, otherwise reading the disks will be bad.
Tell me, please, how and how can I clean the laser on the console?
Well, it seems that there is a special liquid for this, but you can just blow it and wipe it with some dry cloth.
It is better to blow off the dust with a small enema
Lost, my psx is already seven or eight years old. There were problems with reading, and the best way is with a fiber miracle cloth, which is sold in any optics and on any tray with Chinese glasses. It leaves no dust and cleans everything perfectly. Recently wiped my PS2, everything rustles perfectly now.
Do not forget that in addition to the lens, there is a refractive mirror in the head, which can also become dusty over time. Blowing and cleaning the lens in this case may not bring visible results. To clean the mirror, you need to disassemble the head 🙂
I have done this operation several times. To a friend and to myself, discs that were not read are now read as much as a run.Well, do not forget to lubricate the drive. And then from prolonged use, the old lubricant is depleted. I use Vaseline for such purposes. Works well, does not creak 🙂
brill, you can take a picture of where to disassemble and what to clean and lubricate, very relevant for my PSX (thick), it works fine only on the edge
Unfortunately, I didn’t take pictures, it’s not so difficult there, the main thing is attentiveness, accuracy and cleanliness. Because dust is enemy #1.
I also bought a thick PSH 7502 in 1998, the SDR is native, although I periodically make those prefixes. service. Once even my sister threw it into a basin of water, soldered the entire board with a hot air gun, and washed it in alcohol. Recently I took it apart, I thought there would be oxides, but no, the prefix works well.
I also cleaned my Sonya's eye and mirror, it seemed to get better. but then I still had to change the laser, but you can clean it without disassembling the head, crawl with a thin stick like a match, the main thing is not to be zealous, otherwise you can move the mirror
Yes yo mayo! Drive from PSOne is worth a penny! You can also buy one to continue enjoying the games 🙂
There, the mirror is calibrated and quite strongly glued to the metal base of the head, if you moved it with a stick, then there is one conclusion. And if you added it back and it still works for you after that, then you are terribly lucky.
On the worm gear, which is responsible for the movement of the laser reading from the disk, dust can accumulate. I clean this rot with a wooden toothpick, this method is relatively safe for the SD mechanism. The main thing is not to press with all the dope, but to gently clean it. Prefixes are often brought with a complaint about incorrect operation. And very often the prefix of the people is on the floor all the time.
I'll try to explain in more detail:
I do electronics repair.
And then it fell into my hands PS1 SCPH-5502 PAL with comment:
She doesn't want to read CDs.
Well I guess “I’ll clean the peephole and everything is fine, in extreme cases I’ll change the drive”
(by the way, the drive at the console KSM440ADM)
After eye cleaning “what a miracle, he started with great difficulty, but still read discs, even if not all of them”
Tried to clean the peephole again “and then you never know - it will help!”, but it did not give positive results.
(Although I even managed to play Tekken 3, though I almost died on hellishly long downloads, from 5 to 20 minutes. I turned the prefix in every possible way and put it on all sides, but that didn’t help either.)
I decided to take it all apart - clean it from dust, but this did not help.
But then I noticed that the prefix turns out to be chipped.
And apparently, either the manufacturer O.O ”or the supplier, because, for almost 18 years of the life of this set-top box (dated August 1998), no one except me disassembled it, which was proved by the tightly locked case and untouched license stickers on the case.
Generally,
Maybe it's the chip and it's worth unsoldering and trying without it?
Maybe I'm dumb?
Can you advise what could be the issue?
Breaking a set-top box, joystick or any other electronic device, unfortunately, is not difficult. It is enough to drop it, and the screen will break, the button will break, or it will completely stop turning on.
If you get water or any drinks, you can get sticky keys, stains on the display, and battery failure. Also, the way the device is used has a lot to do with the state of the device. Joysticks and portable consoles sink, break off, buttons and sticks are erased. With frequent use of wired headsets or headphones, the connectors for connecting them are loosened. All in all, a lot of things can go wrong.
None of these reasons, as a rule, yet a reason to throw away or change the device. Yes, at a flea market or in the electronics market, they will gladly buy a game console or joystick from you, as sellers know that most breakdowns can be fixed quite easily. They tell you a low purchase price, and after the repair they sell an updated device for a much higher price.
If you encounter a defect that was not caused by your actions, and the set-top box is still under warranty, then you should contact the store or the manufacturer for a free repair or return the faulty console altogether.
We advise you to carefully study the appearance and behavior of the set-top box (or joystick), read about similar cases on the Internet. Perhaps you can fix the problem yourself or find a good workshop in your city.
If the warranty period has expired, or the breakdown does not pass as a warranty case, then you may be considering the possibility of repairing the game console or gamepad yourself. Before you start, think carefully and study everything.
Nowadays, you can find short video tutorials and instructions with photos on almost any topic. However, keep in mind that not all of them are detailed enough and not all authors are competent in the issues they write or talk about. If you still decide to act at your own peril and risk, then before starting, look (or read) the instructions to the end. You may not have all the necessary tools, programs, wires, and skills, which will not allow you to make repairs successfully.
Remember that attempting to repair it yourself, you lose the warranty and increase the likelihood of a complete failure of your set-top box or joystick.
Not all consoles or accessories are so easy to disassemble without special training and tools. It often turns out that the two halves of the plastic case of a gamepad or portable console are connected by a cable that easily breaks when you try to open the case. It is also possible to push through the screen, trying to separate certain parts, especially if you miss some places where these parts are attached to each other.
The next question will be the correct diagnosis of the problem, which for a beginner who does not understand electronics can be a daunting task. And even if you can correctly determine what needs to be replaced in the device, then not all spare parts can be easily obtained. Rather, on the contrary, most of the spare parts for game consoles and accessories for them are not sold in Russia or have a very high cost. In workshops that constantly deal with the repair of consoles, joysticks and other gaming equipment, there are constant suppliers of spare parts, and it will not be a problem for the service center to find the right mechanism, board or connector.
Weigh all the risks. If you have any doubts that you will succeed at the end of the repair at home, contact a specialized service center for the repair of game consoles.
If you want your set-top box to be correctly diagnosed and repaired professionally and with a guarantee, then take it to the workshop. Ultimately, it may be cheaper than self-repair.
- Firstly, an experienced master will do the job much faster and with a predictable result.
- Secondly, the workshop purchases spare parts for consoles and joysticks at a wholesale price, and sometimes the repair cost is the same as what you would be charged for buying a spare part at a retail price.
- Thirdly, without experience, you can damage something when trying to fix a defect that has arisen, which will lead to an increase in the number of breakdowns, as well as the total cost of fixing them.
If you have any problems with a game console, joystick or other gaming equipment, you can always contact us. Diagnosis in our workshops is always free of charge.
Replacing the PS1 video connector is a very common procedure. It is invariably necessary and in demand in repair service centers. PlayStation 1
Replacing PS1 power connectors is another highly requested service at repair service centers. In general, PS1 connectors, despite the fact that
You can find out pretty quickly that a PS1 laser needs to be replaced. It is the laser that is responsible for the normal reading of discs, therefore
Replacing PS1 buttons and sticks is a standard procedure, always relevant and in demand. It is the PS1 gamepads that take the brunt of the load
Repair of the PS1 gamepad remains an actual service, despite the impressive age of the console. The prefix itself was released a long time ago, but still
The console itself will signal to you that a PS1 power supply needs to be replaced. It is very difficult not to notice the problem with the power supply,
Repair of the PS1 power supply may be required for several reasons. Most often, the cause of the combustion of the part is unstable voltage in the house. Because of
Sony PlayStation 1 repair in Moscow has been and remains in demand, despite the impressive age of the game console. Many years have passed since the release of this set-top box, however, even today there are loyal fans of the device who are not ready to exchange it for more modern options.
PlayStation 1 is not bad in its own way. This is a model tested by time and thousands of users, which provides opportunities for a full-fledged game.
For the most part, Sony PlayStation 1 breaks due to the natural wear and tear of components. Intensive operation for many years makes itself felt, so that many parts wear out over time and become unusable.
Such a process is inevitable, and you can only delay the breakdown, but not eliminate it completely.
The PS1 drive, which is used constantly and very actively, takes on a special load. Careless handling of the drive mechanism can add even more problems.
As for the most common breakdowns, they are standard and easily recognizable.
- The drive breaks as a result of abrasion of the components of the mechanism, and the laser head that reads information from the disks also often fails.
- As for the controllers, they wear out naturally, requiring replacement buttons and sticks.
- Power surges in your home can cause your PS1 power supply to burn out, another common problem with game consoles.
- Finally, careless handling of the set-top box may lead to the need to replace various parts, for example, device connectors.
Either way, if something goes wrong with your console, the best thing you can do is take it to a repairman. Self-intervention, quite possibly, will become an aggravating factor that will make repairs even more expensive.
In our service center you can repair the game console of any model. We will check the performance of the device, repair the PS1 gamepads and perform other work on the day of contacting the service.
The consoles that came out a few years ago have been and remain popular with gamers. Someone falls in love with the console at first sight, and someone likes this particular model, and the game completely suits him.
|
Video (click to play). |
If you are a PS1 fan and your console is malfunctioning, bring it to us. Our masters will cope even with such breakdowns, which were refused in other service centers.
