In detail: DIY repair of a Zelmer 919 vacuum cleaner from a real master for the site my.housecope.com.
Zelmer 919.0 st vacuum cleaner coil repair
To get to the coil you just need to remove the front
On the sides from the bottom, open the doors and use a short screwdriver
we unscrew the screws, but I also removed the doors on the right side
you need to remove the bolt and two screws under it
The front part is prevented from removing the wires going to the control board
We unscrew three self-tapping screws and remove the part with tubes
do not lose the rubber rings on the tubes through the formed
snap the hole off the panel latches with buttons
we get to the control board disconnect the wires
Unclench and spray WD40 press on the axle with a screwdriver
one of the sidewalls is removed remove the white disc with a spring
take out the current collector with rings solder the wires
The wires apparently came off from the fact that the rings
scroll on the current collector and when pulling the cord
the wires moved here and there broke off
Therefore, the rings must be glued during assembly.
The spring must be corrected before assembly as in the photo
We tighten the spring contacts
For those who have forgotten where the wires were
Krasnoyarsk repair of vacuum cleaners t. 8 933 332 3164
The spray nozzle for wet cleaning of the Zelmer Aquawelt 919.0 ST vacuum cleaner is often clogged. As a result, water with detergent spills in multidirectional jets and does not evenly wet the surface. The manufacturer, in the spirit of the newspaper column "Notes to the Hostess," suggests trying to clean the nozzle with a taut thread. But this method is ineffective: soon the sprayer clogs up again, and then it stops working altogether due to deformation of the plastic.
IMHO, the Poles from Zelmer set themselves the task of producing an inexpensive washing vacuum cleaner and, in general, fulfilled it. The result is a large and heavy assembly curve apparatus made of fragile plastic. Nevertheless, the vacuum cleaner copes with its tasks, but requires constant attention and participation. For example, according to the same instructions, the "turbo brush" (the one that collects wool and hair) should be cleaned with scissors, no other more convenient mechanisms are provided.
Video (click to play).
The manufacturer suggests trying to clean the nozzle of the Zelmer Aquawelt 919.0 S vacuum cleaner with a taut thread
But back to the repair of the Zelmer Aquawelt 919.0 ST sprayer. I was helped by a video showing how to replace a nozzle with a garden sprayer.
Having said "thank you" to this craftsman, I went to the nearest building supermarket for everything I needed. I will say right away that I did not find exactly the same sprayer with a pump and a brass nozzle, but I came across a nozzle for a bottle called "Geolia Garden Sprayer", which fits very well into the new design.
So, you need the following things:
Native atomizer removed from the nozzle of the vacuum cleaner with pliers.
Garden or household spray with a metal nozzle. Diameter> 8mm.
Hacksaw for metal.
FUM tape.
Saw off the tip of the native sprayer with a hacksaw. The tip is no longer needed.
Saw off the tip of the donor spray with a hacksaw. We use common sense when choosing the size: the new nozzle will consist of two parts, one of which is inserted into the other. The total size of the connected part should be approximately equal to the size of the original nozzle.
In my case, there was another one inside the sprayer tube - a hollow, but already plastic tube, which in its diameter completely coincided with the hole inside the native nozzle. So I just wrapped a good layer of FUM tape around the rest of the base of my original atomizer, put it on a thin tube and screwed both halves of the part into each other. Sawed off the rest of the thin tube.
There may not be a thin tube, but in this case, we simply connect the parts using an FUM tape.
Then we carefully return the sprayer to its place in the nozzle, assemble the vacuum cleaner and check for a leak at the junction.If there is a leak, then the FUM tape layer needs to be increased.
The result is a new atomizer with an old base. which does not clog and performs its function perfectly.
Updated (December 2015). Today, the vacuum cleaner is still sold in stores. In my opinion, this technique is shitty. Below is a list of the parts that came on in the order in which they broke. Draw your own conclusions.
Conventional brush: one wheel.
All brushes with nozzles.
Water release button (fasteners squeezing the water hose to increase / shut off the water pressure).
Compressor: does not supply water from the container.
I bought a Zelmer Aquawelt 919.0 ST, used it for a month, cleaned the apartment once a week, refused to turn on for the next cleaning, although I left it intact. I’ll probably do it myself to the service center, I’ll probably do it myself. In short, I’m not satisfied with the quality.
Not bad, of average quality. Immediately the retainer on the retractable tube broke. We did not go for repairs anywhere, and we suffer. But the turbo brush pleases. Only a year later we realized that if you open a window on it, it rotates better.
When turned on, all the blue and a red lamp are on and the motor does not start, the worker motor checked it myself, I put it in the vacuum cleaner, it does not work, the working button can be a board or a transistor near the motor.
hello, the problem is that the vacuum cleaner drops and gains power by itself, you vacuum the vacuum cleaner and then the bang turns off for a second and then turns on itself
worst vacuum cleaner. At first I dumped the power, and then stopped turning on altogether. This is the first and last purchase of the Zelmer brand.
Write review Zelmer Aquawelt 919.0 ST Describe how satisfied or dissatisfied you are with your purchase Zelmer Aquawelt 919.0 ST
either it turns on from the 10th time, or it does not turn on at all and the indicator of clogging of the air intake hole is on. what is and how to fix it?
does not supply water to the sprayer although the sprayer itself and the hose are not clogged
The turbo brush rotates very slowly even at maximum power, cleaning does not help, I don’t want to disassemble it myself, what could be the problem?
The hose does not come out from the vacuum cleaner after working in the washing mode. How to pull it out?
When turned on, all the blue and a red lamp are on and the motor does not start, the worker motor checked it myself, I put it in the vacuum cleaner, it does not work, the working button can be a board or a transistor near the motor.
I took it out of the case. I checked the circuit at the terminals with the device. She is absent. Does this type of motor mean that its winding has blown?
worked fine. We decided to turn it on again, it does not turn on. Everyone checked the water level in the bucket and the switch button does not respond. Tell me what to do
either it turns on from the 10th time, or it does not turn on at all and the indicator of clogging of the air intake hole is on. what is and how to fix it?
The suction power is constantly dropping to one. Both wet and dry cleaning. I checked all the filters - everything is clean. What is the problem?
A week later, the retractable tube adjustment lock broke. A year later, he refused to turn on. LEDs are on and silent.
The video was uploaded by Dmitry Z. Search for Dmitry Z. 7 months ago
This video shows how you can make an air blower (blower) from ANY vacuum cleaner How to get a big discount on building materials see here
Hello everyone. Recently I got a vacuum cleaner that worked very badly, although it was completely new. And I began to investigate why this is happening, and in the end I got such a design.
A tale of how to repair a vacuum cleaner in a particularly perverse form.
In this video, I tried to talk about how you can repair a vacuum cleaner, or rather its cord winding mechanism, with your own hands. A common problem with the failure of the winding mechanism is the breakage of the flat spring. You can learn how to restore it from the video. #repair of the mechanism for the vacuum cleaner cable reel #repair of the vacuum cleaner Anyone who wants to support the channel financially. Individual gratitude will be expressed to each.
When disassembling the motor of the Zelmer Aquawelt 919.0 ST washing vacuum cleaner, it turned out that the noise and vibration were caused by a broken bearing!
After the purchase, I immediately started cleaning, dry, at the end I turned it off, disassembled and hid it.
Dima Poured water into the tank?
Nikolay I don’t know, this one has served me for quite a long time without any tips, and in general, as it was written, the only thing that immediately flies there is the wheel on the nozzle. Are you really turning on the start, not the pump? ? Water is not necessary if there is a dust collector ..
Tags: How to disassemble the vacuum cleaner Zelmer Aquawelt 919.0 st
The video shows in order how to disassemble a Zelmer vacuum cleaner, how to replace the motor and which motor.
