If the following message appears when inserting a smart card: “Smart card is incorrect Smart card is not inserted “
, then the fastest on the receiver board is the smartcard controller TDA8024 .
We change it and rejoice
Operating voltages on the board:
Message :
If such a garbage happened and the flashing did not help, then the fastest of all is an iron problem:
In my case, the receiving module turned out to be the culprit:
And upon opening it, flooding and corrosion were found:
Plus, after removing the module, the track was damaged:
The module includes: m88ts2022 (DVB-S2 / DVB-S / ABS-S tuner) and M88DS3103 (DVB-S2 / S demodulator)
Accordingly, I had to replace the module from the donor. and throw the track MGTF - ohm.
Only the radio works (as an option), does not reset to factory settings, freezes and turns off, is not flashed via USB, is not updated in any way.
Written by Administrator on 07 December 2011.
Hello, today we will try to fix the Tricolor TV receiver with our own hands. Many faced such a problem when the warranty (usually it is 12 months) expired, and the receiver suddenly failed. A new one is expensive, and in most cases the repair will not be difficult and will cost a penny, if you are even a little friends with a soldering iron, the main and most common faults are easy to fix yourself. Let's consider such a repair using the example of another GS-8300 N receiver from the Tricolor TV company. I must say that the device is not of the best quality, and of course, Tricolor TV is not worth the money that Tricolor TV takes for it. But, nevertheless, the number of subscribers is large and not all of them work for a long time and regularly.
The main and most common malfunction of all receivers is a malfunction in the power supply and voltage conversion circuit. Also, the modulator often fails due to a short circuit in the coaxial cable from the LNB, although the latest models have good protection against short circuits in the cable, when triggered, the voltage supply to the converter simply stops until the short circuit is eliminated.
And so, our receiver does not show any signs of life, the indicators on the front panel display do not light up, and no twitching of the power plug from the outlet and turning on the toggle switch does not help us (at least that was the case with the device, an example of which is given in this article) ... The first thing we do is pull out the plug from the network and remove the top cover, we need to get to the electronic filling of the device. And here it is important to remember one thing, namely, about the warranty seal, which of course we will break if we remove the cover. Therefore, once again make sure that the warranty period has definitely expired, and under warranty no one will repair it for you. If the warranty is still valid, I advise you to take the receiver to a service center and entrust this matter to a specialist.
The electrolytic or oxide capacitor at the input often dries up and fails, which is also a malfunction, not everyone can find such a breakdown either, you need to have at least an initial level of a radio amateur. Usually, defective capacitors have a yellowish appearance, or a small brown speck on the board at the base of the legs.Also, the serviceability of a capacitor can be determined by comparing its nominal and measured capacitance.
The receiver uses direct current, which is rectified from the AC mains using a diode bridge. Problems with the diode bridge also happen. It is very simple to check diodes, the main function of a semiconductor diode is to pass current in one direction, and not in the other. In my case, the transistor of the primary winding of the transformer turned out to be faulty, it is not difficult to find it, it usually has a radiator to remove heat. I determined the malfunction of the transistor by measuring the voltage at its emitter, it was absent there, the primary winding was not powered, respectively, everything else is de-energized. The transistor cost me 28.5 rubles. Replacing it with a soldering iron, I eliminated the malfunction and the receiver is back in working order. I must say such a breakdown is quite a rare occurrence, usually it all ends with a fuse.
A very common malfunction is a firmware crash. The firmware often crashes, this is usually evidenced by the complete hang of the receiver. In this case, "flashing" will help. I also want to say about another cause of the malfunction, which may arise due to poor-quality installation. Water in the cable. If the outer insulation of the cable is broken, then water from atmospheric precipitation can get inside and it easily enters the receiver like a hose, sometimes flooding all of its insides. The condition of the cable must be monitored throughout the entire service life of the device.
Electronic devices surround us everywhere: on the street, at work, at home. With the rapid growth and availability of satellite television to the general public, a wide range of satellite equipment has emerged for the general public. These are satellite receivers, conditional access modules, antennas, converters, etc. Whether we like it or not, sooner or later breakdowns occur with them, which cause us to feel the loss of our beloved thing.
You should not despair - for this there are service centers that you can turn to and they will help you to bring your equipment back to life.
Breakdowns of equipment occur for various reasons - voltage drops, failure of various nodes, wear and tear of the equipment itself from its venerable age, you can also note the incompetence of the owners themselves, for example, improper replacement of software in satellite and cable receivers.
Power supply failure is perhaps the most common type of digital terminal failure. It arises for various reasons: a poor-quality supply network (see photo), poor-quality radio components were used, especially this is de facto in Chinese technology.
Also, this can include violation of operation, dust, dirt, as a result of this, the thermal regime is not correct (see photo).
A service center is a structural unit within a company. He is responsible not only for the repair and maintenance of the products sold by our company, but also for the repair (including warranty) of satellite equipment from other companies. Our clients are not only individuals - users, but also equipment dealers who seek to save their customers from the problems associated with the repair and maintenance of receivers. Our flexible corporate customer policy allows us to provide adequate service and meet the interests of all customer groups. This is more than 1000 units of equipment per month. To carry out such large volumes, of course, allows the professionalism of the staff, the equipment of the service center with professional equipment, tools and technical documentation. Therefore, in our service center we carry out high-complexity repairs: for example, replacing processors in BGA cases. Repair takes place in the shortest possible time.
The supply department, in addition to its main function - the purchase of equipment, is also engaged in meeting the needs of the service center, purchasing components necessary for repair. And here it is worth noting that the selection and purchase of components for repair is carried out according to the following criterion: the quality of parts comes first, their price comes second, but due to the large volumes of supplies of parts, the price ultimately remains low.
Of course, unforeseen moments happen - for some reason, the repair is delayed. This usually happens due to the lack of some scarce radio component. Sometimes repairs require a complete replacement of the motherboard, and this repair part is not always available. In this case, we are trying to find some acceptable solution together with the client, taking into account his wishes, combined with our capabilities.
At autopsy, found out of order:
According to the table on identification and selection of analogs https://my.housecope.com/wp-content/uploads/ext/2561/ic_power/, the last part was replaced with SG6848 with minimal interference with the factory circuit.
SSS4N60B (TO-220F package) was installed instead of the burnt-out Q1
On Telesputnik posted a diagram of the power supply unit.
The receiver turns on, the LNB has 18 volts. There is no video signal, it gets very hot (the finger does not hold) stv 6419 .. because of it there can be no video? there is no other point? (in the sense that more video signal is not to be taken from?) the receiver switches channels ..
GS 8300N receiver there is no video and audio signal through scart to the TV, the channels are switched on the receiver panel.
the video signal from the STi5119ALC chip can be checked with an oscilloscope at the control point opposite the capacitor C117, then it comes to the resistor R87 and is transmitted to the capacitor C129 and then goes to the STV6419 microcircuit from it there is no output to R91, the culprit is not 12 volts on the board, respectively, there is no power + 12V on the 3rd leg STV6419, a 12 volt Zener diode D3 is faulty near the power connector
There was such an answer: if you use only composite video signal, most likely it can be simply thrown out (replaced with a jumper). And where to put the jumper? if that's the right advice ..
Defective VD3 (VD3 zener diode 12 V) on the motherboard next to the power connector.
Zener diode brand and parameters:
Power supply + 12V for 3rd leg STV6419.
Zener diode analog:
VD3 STV6419 similar Zener diode (SMD) did not find. Put a 0.5 watt glass zener diode the size of a diode kd522 ... While the flight is normal.
If replacing the zener diode did not help:
After the thunderstorm, 6419 swelled. After the replacement, the image did not appear, but when checking the strapping, two resistors were cut off, R91, R95 ... I replaced it, and it worked.
One more problem:
And yet, instead of 13, 18 Volts, 24V was running on the LNB. Replacement required DA1 (LM317T) ... And that's it, the flight is normal
The same situation with the GS-8304 receiver:
After 5 years of operation, the GS-8304 suddenly stopped broadcasting, although the indication is working properly. Zener diode brand MMZE5242B.
Satellite TV is evolving with every update and with every new device. Every satellite TV user from time to time encounters problems and errors in the robot of their receivers or other components. This can be due to various factors. For example, older models may fail due to long operating times. Despite their quality and reliability, devices can break down due to unsatisfactory weather conditions, electrical problems or improper use. Let's take a closer look at this.
Among the reasons for the breakdowns of the GS8306, GS8300, DRS-5001 models are the following:
the receiver does not start;
the timer flashes on the display of the set-top box at startup;
on the display of the prefix only a non-blinking timer;
on the display of the prefix the inscription "boot";
on the display of the prefix error message ER31;
an error on the TV display when switching on "Short circuit!" or "Check antenna cable".
In the case of the last error, you can carry out diagnostics yourself to clarify the cause of the malfunction. When the wire was disconnected, the error message disappeared, the problem is with the satellite converter or the antenna cable. Next, you need to check the wire in case of a short circuit. If it is not there, there is an error in the satellite converter. But, if the TV still signals an error, the problem is in the tuner.
These types of breakdowns include other representatives of the series of MPEG-2, MPEG-4 and Full HD set-top boxes. There is no need to prematurely go to the store for another device, because the purchase will definitely cost a lot. It is recommended to contact service center for qualified help, or repair the receiver with your own hands, if you have the necessary skills.
Diagnostics show that often the accessories of the set-top box fail:
firmware - this can be detected if you see errors on the display;
receiver power supply Tricolor - when the receiver does not turn on or the timer is flashing;
motherboard - only timer is displayed or in case of error ER
However, satellite TV users may encounter picture, sound or signal problems. This also happens due to problems with the receiver. The following are attributed:
breakdown of the satellite converter;
the antenna cable is damaged;
breakdown of the tuner unit;
weak signal due to obscuring trees;
unsatisfactory weather conditions.
The reasons also include channel broadcasting frequency change or even a whole package of channels or satellite malfunctions, to which the service center has nothing to do.
First of all, you do not need to start repairing Tricolor receivers yourself if you are not 100% sure what and how you are doing. If the warranty period is valid, it is best to entrust the repair of the Tricolor satellite receiver to a specialist. But, this is possible if there is a warranty card, purchase receipt, client's signature. The repair warranty may be voided if:
operation of the receiver during power surges;
damage to the seal or the integrity of the structure;
errors when switching, connecting cables or incorrect programming;
the receiver was not installed by an installer, and this led to a breakdown during operation;
the client has violated the terms of use;
All this must be adhered to if the client wishes to repair his receiver in the future.
Repair of the Tricolor TV receiver is as follows:
replacing the motherboard;
changing the power supply;
replacement of the module;
flashing or reinstalling software.
If the motherboard breaks down, it is most often recommended to buy a new and more modern version of the set-top box, because repairing the motherboard will cost almost at the price of a new receiver.
For example, there are a number of errors typical for each type of device and options for correcting. The peculiarity of the repair of the GS8300 receivers of the Tricolor company depends on the alteration of the power supplies, because the devices are not highly resistant to voltage surges. Overheating was a typical problem for the GS 7300, causing the diode bridge or chip to break.Also, the power supplies for the Tricolor receivers sparked after prolonged operation, so they often had to be changed. The most optimal model, the GS8306, also had typical problems. For example, overheating during prolonged viewing of channels.
VIDEO
VIDEO flashing satellite receiver GS 8305 after unsuccessful firmware update via satellite. The video describes an example of how to flash a USB stick of a satellite receiver after an unsuccessful software update through the provider. In other words, a forced downgrade (downgrade, to the previous version) of the firmware is carried out.
LCD TV power supply repair
GS-8306 Antenna short circuit. A rather obscure malfunction of this receiver.
You can contact me through my website there is all contact information as well as Order accessories or send the receiver for repair! ,
VIDEO flashing satellite receiver GS 8305 after unsuccessful firmware update via satellite. The video describes an example of how to flash a USB stick of a satellite receiver after an unsuccessful software update through the provider. In other words, a forced downgrade (downgrade, to the previous version) of the firmware is carried out.
LCD TV power supply repair
GS-8306 Antenna short circuit. A rather obscure malfunction of this receiver.
VIDEO flashing satellite receiver GS 8305 after unsuccessful firmware update via satellite. The video describes an example of how to flash a USB stick of a satellite receiver after an unsuccessful software update through the provider. In other words, a forced downgrade (downgrade, to the previous version) of the firmware is carried out.
LCD TV power supply repair
GS B521 Let's disassemble our copy and see what this receiver has.
Tricolor is a scam. Now you can throw out my receiver, or again follow the lead of Tricolor and buy new equipment every three years. Mmm new
Vitaly Anatolyevich, in general, has nothing to lose, I'll finish it off and calm down
Vitaly Anatolievich 6 개월 전
and have not tried chtol from a flash drive?
Vitaly Anatolyevich I will find computers, I will try
Vitaly Anatolievich 6 개월 전
try to flash it then
Vitaly Anatolyevich shows all the data and status and id and subscription until 19, and that the receiver is valid until 2023. I have been fighting with them since April 3. The cable checked the convector too. The advertising blocks are working and the channels are not there, only the message: there is no access to viewing. Turn off for 3 seconds and so on.
Man Like you without looking. The programmer has not yet mastered this COSMOS for me)))) are there not expensive progromators for 8306 ??
Programmers for microcircuits and not for 8306 or 9305)
Tricolor is a scam. Now you can throw out my receiver, or again follow the lead of Tricolor and buy new equipment every three years. Mmm new
Vitaly Anatolyevich, in general, has nothing to lose, I'll finish it off and calm down
and have not tried chtol from a flash drive?
Vitaly Anatolyevich I will find computers, I will try
try to flash it then
Vitaly Anatolyevich shows all the data and status and id and subscription until 19, and that the receiver is valid until 2023. I have been fighting with them since April 3. The cable checked the convector too. The advertising blocks are working and the channels are not there, only the message: there is no access to viewing. Turn off for 3 seconds and so on.
Man Like you without looking. The programmer has not yet mastered this COSMOS for me)))) are there not expensive progromators for 8306 ??
Programmers for microcircuits and not for 8306 or 9305)
Any product from China “Aliexpress.com” https://ali.pub/uo612 Any product from China “Gearbest.com”.
Repair of the tricolor GS 8306 receiver. Removing and programming SPI Flash. How it's done.
Repair of the GS8306, GS8307, GS6301 receiver. Replacing the flash drive when the firmware is released. Troubleshooting is everlasting.
You can contact me through my website there is all contact information as well as Order accessories.
send a request for receiver repair. ...
At the request of users, https://my.housecope.com/wp-content/uploads/ext/2995/remont-gs-8306-perednyaya-panel/ we upload another video on the topic of repair.
Interesting repair of the tricolor tv receiver. ... Transistor tester.
Any product from China “Aliexpress.com” https://ali.pub/uo612 Any product from China “Gearbest.com”.
Firmware Gs 8306 Dump 1 9 1604 02 00.
Any product from China “Aliexpress.com” https://ali.pub/uo612 Any product from China “Gearbest.com”.
prefix GS 8306 does not work after updating what to do.
Gs 8306 after update, repair https://my.housecope.com/wp-content/uploads/ext/2995/gs-8306-posle-obnovleniya-remont/ We show the whole process,.
Any product from China “Aliexpress.com” https://ali.pub/uo612 ⭕ Any product from China “Gearbest.com”.
Firmware Programmer for Gs 8306.
flashing satellite receiver GS 8305 after unsuccessful firmware update via satellite. The video is described.
Recently, more and more often the company's clients Kirovsat in Kirov, after purchasing and installing a set of satellite television Tricolor in Kirov and connecting to the Tricolor operator, they began to ask one single question about the operation of the GS 8306 HD receiver: “What should I do, I do not have a picture on the TV screen, but the GS 8306 HD Tricolor receiver works and responds with the indicator signaling when you press the keys on the control panel? ".
For help in solving the problem, you can contact our company Kirovsat in Kirov, or find out on your own by reading the article below.
And so, the GS 8306 HD Tricolor receiver is a technically complex device, to start working with which, it is advisable to study the instructions attached to the set of satellite equipment.
As you have noticed, the reverse side of the GS 8306 HD Tricolor receiver has 2 outputs: RCA output "tulip" and HDMI, to switch between which, on the receiver's remote control, there is an “input signal” button located in the upper left part of the remote control ...
Some users of GS 8306 HD Tricolor receivers connected to a TV via RCA or HDMI output, when switching channels, mistakenly press the “input signal” button, as a result of which the GS 8306 HD Tricolor receiver switches to another output and the image on the TV disappears.
As a rule, older people start to panic and in order to return the receiver to normal operation, they begin to sort out all the keys on the remote control of the GS 8306 HD Tricolor receiver, which, of course, does not lead to the desired result. There are also subscribers of the Tricolor operator who, in such a situation, bring their GS 8306 HD Tricolor satellite receiver to one of the service centers located in Kirov and other regions of Russia.
Next, there will be a list of the operating modes of the indicator light of the GS 8306 HD Tricolor receiver with a decoding of the operating mode in which the receiver is located and the options for your actions to bring the receiver into working condition:
1. The indicator light is off - the receiver is turned off (to turn it on, press the "on" button on the front panel of the receiver) 2. The indicator light flashes alternately - the receiver is turned off, in standby mode (to turn on, press the "on" button on the receiver's remote control) 3. On the indicator light, one upper light is on - the receiver is turned on, the signal is taken from the RCA output “tulips” (to switch to HDMI output, press the “input signal” button once) 4. The indicator light is on completely (not flashing) - the receiver is on, waiting for switching between the RCA and HDMI outputs (do not press anything, wait until one of the lights is on: top or bottom) 5.One bottom light is on on the indicator light - the receiver is turned on, the signal is taken from the HDMI output (to switch to RCA output, press the "input" button once)
If both indicators on your receiver are lit for a long time and the GS 8306 receiver does not react to the remote control in any way, the first step is to turn off the receiver from the power supply for 2-3 minutes. If the problem persists after turning it on, try to flash the receiver from an external USB drive. How to do this is described in the article "Updating GS 8306 Tricolor Firmware".
Thus, you have familiarized yourself with all the operating modes of the GS 8306 HD Tricolor receiver, and we hope that a small note from our Kirovsat company in Kirov will help you eliminate cases of worries about the performance of your receiver.
Video (click to play).
